AZ9371

SENSITIVE SUBMINIATURE RELAY
FEATURES Extremely small footprint Thin vertical profile, only 7 mm wide High sensitivity, 113 mW pickup Dielectric strength 4000 Vrms 5 Amp switching capability (version T 10 Amp) Two different footprints available Reinforced insulation (VDE 0700, 0631) footprint Version K UL, CUR file E44211 VDE certificate 40030746 GENERAL DATA
Life Expectancy Mechanical 150 W or 1385 VA 300 W or 2770 VA) 5A 10 A) 30 VDC* or 277 VAC Standard version Electrical 1 x 105 at 5 A, 250 VAC res. [1] 5 x 104 at 5 A, 250 VAC res. [2] High capacity version T Electrical 1 x 105 at 7 A, 250 VAC res. [1] 1 x 104 at 10 A, 250 VAC res. [1][2] Standard version 5 A at 277 VAC, resistive, 85C, 50k cycles [1][2] 5 A at 30 VDC, resistive, 85C, 50k cycles [1][2] 3 A at 277 VAC, resistive, 85C, 120k cycles [1][2] 3 A at 30 VDC, resistive, 85C, 120k cycles [1][2] B300 [2] R300 [2] High capacity version T 10 A at 277 VAC, resistive, 85C, 10k cycles [1][2] 10 A at 30 VDC, resistive, 85C, 10k cycles [1][2] 7 A at 277 VAC, resistive, 85C, 60k cycles [2] 7 A at 277 VAC, resistive, 105C, 50k cycles [1] 7 A at 30 VDC, resistive, 85C, 60k cycles [2] 7 A at 30 VDC, resistive, 105C, 50k cycles [1] VDE Standard version 5 A at 250 VAC, resistive, 85C, 50k cycles [1][2] 5 A at 30 VDC, resistive, 85C, 30k cycles [1][2] High capacity version T 10 A at 250 VAC, resistive, 85C, 10k cycles [1][2] 10 A at 30 VDC, resistive, 85C, 10k cycles [1][2] 7 A at 250 VAC, resistive, 105C, 50k cycles [1] 7 A at 250 VAC, resistive, 85C, 50k cycles [2] 7 A at 30 VDC, resistive, 105C, 50k cycles [1] 7 A at 30 VDC, resistive, 85C, 50k cycles [2] Material Resistance Silver nickel [1], silver tin oxide [2], gold plating available < 100 milliohms initially (at 6 V, 1 A, voltage drop method) 3 x 104 at 7 A, 250 VAC res. [2] Operate Time (typical) Release Time (typical) Dielectric Strength (at sea level for 1 min.) Surge Voltage Coil to contact Insulation Resistance Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure Terminals Max. Solder Temp. Max. Solder Time Max. Solvent Temp. Max. Immersion Time Weight 6 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) 4000 Vrms coil to contact 1000 Vrms between open contacts 10,000 V (at 1.2x50 s) 1000 megohms min. at 20C, 500 VDC, 50% RH Greater than 5% of nominal coil voltage At nominal coil voltage -40C (-40F) to 85C (185F) -40C (-40F) to 105C (221F) 0.062" (1.5 mm) DA at 1055 Hz 10 g P.B.T. polyester Tinned copper alloy, P.C. 270C (518F) 5 seconds 80C (176F) 30 seconds 3 grams Minimum operations 5 million operations

CONTACTS

Arrangement Ratings SPST (1 Form A) Resistive load: Max. switched power: (Version T: Max. switched current: (Version T: Max. switched voltage:
* Note: If switching voltage is greater than 30 VDC,
special precautions must be taken. Please contact the factory.

Rated Load UL

ZETTLER

electronics GmbH

Tel. +0 Fax +200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com

2010-12-08

Junkersstrasse 3, D-82178 Puchheim, Germany
Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 113 mW
750 mW at 20C (68F) ambient 1. All values at 20C (68F) 2. Relay may pull in with less than Must Operate value. 3. Mounting position terminals upside is not recommended, if an electrical or mechanical life of > 100,000 operations is required. 4. Specifications subject to change without notice.
26C (47F) at nominal coil voltage Max. 105C (221F)

RELAY ORDERING DATA

COIL SPECIFICATIONS
Nominal Coil VDC 24 Must Operate VDC 2.25 3.75 4.50 6.75 9.00 13.50 18.00 Max. Continuous VDC 5.8 9.7 11.6 17.4 23.2 34.8 46.5 Coil Resistance Ohm 10% 720 1,620 2,880

ORDER NUMBER

AZ9371-1A-3D AZ9371-1A-5D AZ9371-1A-6D AZ9371-1A-9D AZ9371-1A-12D AZ9371-1A-18D AZ9371-1A-24D
* 1A denote silver nickel contacts. Add suffix E to 1A for silver tin oxide contacts. Add suffix T after AZ9371 for high capacity version. Add suffix E for sealed version. Add suffix K for different footprint (meets reinforced insulation (VDE 0700, 0631)) Add suffix G at the end of order number for gold plated contacts.

MECHANICAL DATA

Standard Pinning Outline Dimensions
Version"K" Pinning Outline Dimensions

20.5 max

7.2 max

15.3 0.3

3.4 0.3

+ 0.15 - 0.1

0.3 7.0

0.4 - 0.05 4.7

0.3 3.5

PC BOARD LAYOUT

4 x 1.x 1.1

Viewed toward terminals

WIRING DIAGRAM
Attention! Grid is not 0.1 (2.54 mm)!!

Project Scope Guide

The following guide will help you to identify the goals and needs of your website and it will allow us to give you a customized quote that accommodates them.
RAN LOGIC S.R.L. Darwin 1154, C/2B Buenos Aires (1414) Argentina T +(11) 4855-9371 info@ranlogic.com www.ranlogic.com
Please, answer the questions in a concisely. Include any additional relevant information at the end of the document. Do not worry about completing all the questions if you don't have the answers or believe they do not apply to your project. Once you nish completing the form, please send it to George Taylor, at lt@ranlogic.com Should you have any questions, please do not hesitate to contact him via email or by phone to (+54 11) 4855 9371

General Information

1. Company name 2. Brief company description 3. Desired website deployment date
4. Do you have a pre-established budget for website development? 5. Can the project be divided into several phases to adjust to time and/or budget limitations? 6. Is your company present on the internet at the moment? (If so, please provide website address)
Website Goals and Target Audience
1. Please describe your primary and secondary goals for this project. 2. If you are promoting products or services, please describe their history, market position and customer base. 3. How will you measure success for this project? (e.g. lowering customer service phone call numbers, improve communications from/to your providers, increase sales, etc) 4. How often do your customers visit your site? What do they use it for? 5. What is the most important action that your customers perform on your website, for your company? (e.g. Learning about your products, shop, suscribe to a mailing list, etc) 5. What are the bottom line reasons why the users choose the products or services from your company? (e.g. price, quality, customer care, etc)

Design

1. Do you have an existing corporate identity?(Iso and / or logo, company colors, visual identity manual, etc) If so, please send us the material via email. 2. Do you need us to do the graphic design for your site? If not, who will be in charge of that?
3. Are there any websites of companies similar to your own that you have liked?Please send us the web addresses and tell us what you liked/disliked from each. 4. Using adjectives or short phrases, please describe the way in which you would like the average customer to perceive your site (e.g. Reliable, fun, innovating, modern, exclusive, good for the entire family, easy to understand) 5. How is your company seen at the moment? Would you like the new website to encourage this perception or to promote a change on it?

Content

1. Have you planned the content and structure of your site? If so, please describe it briey. If not, do you need us to help you with this? 2. Will the site use content that is already published some where else? (e.g. advertising material, magazines, iers, company internal documentation, etc) 3. How many pages will the site have approximately? 4. Are you planning to keep the site updated? If so, how often? Who will be in charge of updating it?

Technologies

1. What is the operating system and browser that most of your users use?(this is in case you know or foresee it) 2. Is there any technology (XHTML, JavaScript, Flash) that you would like your site to use? If so, how would its implementation benet the user experience?

3. Do you need a content management system? Do you already have one? If so, please describe it, and tell us how it is working for you. 4. Do you need a system to perform secure online transactions? (ecommerce). 5. Does your site need any other feature? (Customization capacity, le management, etc)
Additional information and Comments
We encourage you to write as much as you need to let us know about any important aspect or item that we have not asked you about and that you consider important. Feel free to add any comments and suggestions. Thank you for completing our form! All you need to do now is send it to us, attaching the material (the one we asked for and anything else you believe is relevant) to George Taylor at lt@ranlogic.com and we will send you our proposal soon after.