Installation Guide

GH-UD U E - F C

Caution

The following are not covered by the warranty : 1. Use the product incorrectly or in a manner other than the designed purpose. 2. Nonobservance of the proper operation provided. (e.g. over-clocking) 3. Malfunction due to interference from other devices. 4. Fail to install due to the specification of the VGA card or other components that are not supported by the product. 5. Unauthorized modification of the product. 6. Malfunction arising from casualties (earthquake, thunder, fire, and flood). 7. The warranty label of the product has been removed or damaged. 8. Any loss caused by removing the original heat sink on VGA card. 9. Any loss caused by failure to follow the installation process contained in the user.

Bracket Instruction

TYPE A

PCI-E nVIDIA

GeForce 6600 LE GeForce 6600 GeForce 6600 GT

TYPE B

AGP PCI-E ATi nVIDIA ATi
RADEON X800 XL RADEON X800 GTO RADEON X800 RADEON X800 XT RADEON X800 Pro RADEON X700 XT RADEON X700 Pro RADEON X700

AGP nVIDIA ATi

RADEON X800 XL RADEON X800 RADEON X800 XT RADEON X800 Pro
RADEON X1650 XT RADEON X1650 Pro RADEON X1600 XT

nVIDIA

GeForce 7300 GS RADEON X1600 Pro GeForce 7600 GS RADEON X1300 Pro GeForce 7600 GT RADEON X1300

Features

1. Supports nVIDIA SLi and ATi CrossFire. 2. High Performance Aluminum fin with copper pillar and base to advance thermal circulation. 3. Radial airflow 8 cm fan with radial airflow to enhance thermal circulation of surrounding components. 4. Light weight Only 200g, VGA card loading free. 5. Two covers in red and green Users may use the cover depend on their preference. 6. Ball bearing fan with 2300 rpm provides quiet and long life expectancy and reliability. 7. Heat sink for memory. 8. Easy and fast installation.
Installation Instruction Specification
Heat Sink Dimension : 160 x 91 x 34 mm Fan Dimension : 80 x 80 x 15 mm Base material : Copper Fin material : Aluminum Rated Voltage : 12 V Rated Current : 0.19 Amp Fan Speed : 2300 rpm Noise : 25 dBA Bearing Type : EBR Bearing Fan Life Expectancy : 30,000 hr Support : nVIDIA 6600 PCI-E series nVIDIA 7600 PCI-E serie ATi RADEON X1650 series ATi RADEON X700 series ATi RADEON X1600 series ATi RADEON X1300 series ATi RADEON X800 series

( ATi and nVIDIA )

Remove the original cooler on the VGA card and clean the grease.

( as Figure A )

STEP 1
Remove heat sinks on the memories if any. Caution : Please be careful while removing the original heat sink on the VGA card. GIGABYTE is not responsible to any loss caused during the removing process. According to the STEP number of the memories on the VGA card, to remove the sticker on the back of the heat sinks and paste on the memories.
Figure B ( as Figure B ) Figure C

Figure A

Apply the STEP grease on the VGA chip appropriately.

( as Figure C )

Accessories

Figure D

To replace the cover, use the pincer compress the collapsible end of the push clips to slide out to remove the original cover and put on the new one by aligning the push clips with the lock holes on the cooler and pushed completely through the holes to lock it. ( as Figure D )

STEP 4

Tear off the STEP sticker on the copper base. ( as Figure E )

Figure E

STEP 6
2) Wrench x 1 3) Heat Sink x 8 4) Washer x 4

Figure F

with wrench. ( as Figure F )
Lock the screws on the bracket
Please lock the screws on the appropriate positions. Figure G
Place the STEP cooler on the table and align the holes for the screws on the VGA card to the screws on the cooler.

( as Figure G )

1) Cover ( red ) x 1 5) Nut x 4 6) Screw x 4 7) Grease x 1

Figure H

Place the washers on STEP the screws and lock the nuts on the screws with screwdriver to fasten the cooler.
(as Figure H) To avoid the damage to the c h i p, p l e a s e l o c k t h e n u t s diagonally.
To complete STEP the installation, connect the power cord of the fan to the output of the power supply.
( as Figure I ) While installing the power cord of the fan, please be careful not to interfere to the blade.

Figure I