s Never allow metallic objects, such as staples and paper clips, to enter inside your device. Metallic objects, such as staples and paper clips, if allowed to enter your device, could cause the generation of excess heat or fire. s Never connect terminals (metal parts) to metallic objects (such as wires). Connecting terminals to metal objects could cause excessive heat or fire. s Always immediately disconnect the AC Adapter from the power outlet and turn the battery switch to the Stop position in the event the device emits an unusual odor or sound or generates smoke.
s Never use or store your device in the following locations: Anywhere it may be exposed to water, such as a bathroom or sauna; In conditions of high humidity, such as in the rain or fog; Where your device will be exposed to high temperatures, such as near a fire or equipment that emits high temperatures; In direct sunlight; or In a sealed automobile left in the sun and subject to high temperatures. Never store or transport flammable liquids, gases or explosive materials in the same compartment of your automobile as the device or any of its accessories, as possible sparking in the PC could cause ignition or explosion. When driving, always secure your device in its softcase, when it is not in use. Never place your device on the passenger seat or any place else in the car where it can become a projectile during a collision or stop. s Never drop your device or subject it to severe shock. Dropping your device or subjecting it to severe shock could cause the built-in battery to leak, ignite and/or rupture. s Always immediately remove your device and its battery from the vicinity of any source of heat, such as an open flame, in the event the built-in battery leaks liquid or emits an unusual odor. Continued use of your device under either of these conditions could cause ignition (i.e., fire) of the leaked battery liquid, or rupture. s Never touch any fluid that might leak from the built-in battery. Such liquid when in contact with
the eyes or skin, could cause injury to the skin or eyes. Should the liquid come into contact with the eyes, irrigate the eyes thoroughly with clean water and immediately seek medical attention. In the event the liquid comes into contact with the skin or clothing, wash it away immediately with clean water. Failure to follow the above directions concerning use and storage could result in bodily injury and/ or property damage due to battery liquid leakage, fire or rupture. Failure to follow the above directions concerning use and storage could also result in damage to your device.
s Always use authorized Audiovox accessories and optional devices when operating this device, as the use of incompatible auxiliary equipment could result in fire, electric shock or other bodily injury. The use of unauthorized accessories will also void your Warranty.

Table of Contents

SAFETY INSTRUCTIONS... 5
SAFE USE AND OPERATION OF DEVICE (WIRELESS HANDHELD PHONE)... 12
SAR Information.... 15 Chapter 1: Getting Started.... 18
Welcome.... 19 Where to Find Information... 19

Chapter 2:

Basic Skills.... 20
Parts Names and Function.... 21 Battery Charging... 27 Initial Setup.... 29 Setup Options.... 30 Connecting to a Computer... 31 Today Screen... 32 Programs.... 34 Navigation Bar and Command Bar... 35 Pop-up Menus.... 36 Notifications.... 36 Entering Information.... 37 Entering Text Using the Input Panel... 37 Finding and Organizing Information... 46 Customizing Your Device... 47

Chapter 3:

Phone Functions.... 55
Using Phone Function.... 56 Placing Calls.... 62 Receiving a Call.... 64 Call Waiting.... 66 Call Forwarding.... 66 Three-Way Calling.... 66 Voice Mail..... 66 Digital Numeric Page... 66 Missed Call.... 67 Link Dialing.... 67 Emergency Dialing.... 68 Phone Book.... 68 KeyGuard Lock.... 69 Scratch Pad.... 69
Speed Dial.... 70 Call Log.... 71 Options (Preferences).... 72 SMS (Messaging).... 78 Accessing the Internet.... 83

Chapter 4: Chapter 5:

Microsoft ActiveSync..... 86 Microsoft Pocket Outlook..... 89
Calendar: Scheduling Appointments and Meetings.. 90 Contacts: Tracking Friends and Colleagues... 93 Tasks: Keeping a To Do List... 96 Notes: Capturing Thoughts and Ideas... 99 Inbox: Sending and Receiving E-mail Messages... 101

Chapter 6:

Companion Programs... 106
Pocket Word.... 107 Pocket Excel...111 MSN Messenger.... 113 Windows Media Player for Pocket PC... 117 Microsoft Reader.... 118

Chapter 7:

Pocket Internet Explorer... 122
The Mobile Favorites Folder... 123 Mobile Favorites.... 123 Using AvantGo Channels... 125 Using Pocket Internet Explorer... 126

Chapter 8:

Getting Connected.... 128
Transferring Items Using Infrared... 129 Connecting to the Internet... 130 Connecting to Work... 131 Ending a Connection.... 132 Connecting Directly to an E-mail Server... 132 Get Help on Connecting.... 132

Chapter 9:

Optional Functions.... 133
Home..... 134 Backing Up.... 141

Chapter 10:

Additional Information... 145
Resetting..... 146 Clearing Memory (Initialization)... 147 Specifications.... 148
Chapter 1: Getting Started
Chapter 1 Getting Started

Welcome

Congratulations on the purchase of your Pocket PC. You can keep your most important business and personal information up to date and close at hand. And with the power of Microsoft ActiveSync you can synchronize and download information on your desktop or laptop computer with your handheld device. With your Pocket PC you can: Make and receive phone calls. Instantly view the days appointments with the touch of a button. Send and receive e-mails. Download web pages. Make handwritten notes

Even if the power is turned off, pressing the program button turns the power on and the program screen is displayed. (However, you can change the setting. See Setting Power in Customizing Your Device later in this chapter.) When using the device under high ambient temperatures and the temperature inside of the device goes up (to about 144F or more), the power is forcibly turned off. In this case, after the temperature inside of the device cooled down, turn the power on and use the device under appropriate ambient temperatures. (144F=62C)

Battery Switch

The Battery Switch supplies/cuts the battery power to the device. When shipped, the setting is Stop. Before using your device for the first time: 1. Detach the Color Panel (see illustration) to expose the Battery Switch.
2. Confirm that the Radio Standby Switch is set to OFF, then slide the Battery Switch to Supply (lower side). Battery Switch Lock
3. Reattach the Color Panel.
Note Returning the switch to the Stop (the upper side) resets the device back to its factory settings - initial setup will need to be repeated. To move to the Stop side, slide the switch while inserting the stylus into the Battery Switch Lock.

Charging LED

Steady orange. Built-in battery charging Flashing yellow. Charging has stopped due to extreme temperatures. Charge at a temperature of approximately 41F - 95F (5C and 35C). Steady green. Built-in battery fully charged. Steady yellow.. Built-in battery charging but level is not strong enough to power.
Incoming Call / System Notification LED
Fast flashing orange.. Incoming call (Approx. 2Hz) Slow flashing orange. Indicates alarm as set through Calendar or Tasks. (Approx. 1Hz)

Radio Standby Switch

Determines functionality of device. To turn ON, slide Radio Standby Switch to the upper side. ON. Can be used as phone to make and receive calls OFF.. Cannot function as a phone

Using the Stylus

Use only on touch-screen for menu selection or data input. Tap: Touch the screen once with the stylus to open items and select options. Drag: Hold the stylus on the screen and drag it across to select text and images. Drag in a list to select multiple items. Tap and hold: Tap and hold the stylus on an item to see a list of actions available for that item. On the pop-up menu that appears, tap the action you want to perform.
Note Only use the supplied stylus on the touch screen. If the stylus tip becomes damage, replace with a new one. Using a ballpoint pen or damaged stylus may damage the screen.

About Cursor Button

Navigate the cursor on screen by pressing the upper, lower, right or left part of the cursor button. Press the center of the button to select an option or program.

Note The cursor movement depends on the screen. When the cursor is at the right or the left side of the screen, it may not move.

Earphone Microphone

The supplied Earphone Microphone can be used to receive phone calls. When the Earphone Microphone is inserted into the device, the microphone and speaker on the main unit will become inactive. Also, this microphone can be used as a recorder.

Microphone

To Headphone Jack
You can attach the Earphone Microphone to your pocket, etc., by using this clip.
This devices phone component can be used with the Earphone Microphone or as a speakerphone. Unlike conventional cell phones, it is not designed to be held against the head in conversation. Such unauthorized use of the phone, without an Earphone Microphone or other than as a speakerphone, is contrary to the design of this product and is not recommended. For instructions on how to use the phone with Earphone Microphone or as a speakerphone, please refer to page 61 of this manual.
Note Do not use the Earphone Microphone when turning on and off the device or when connecting or disconnecting the Earphone Microphone to/from the device because a loud noise may be otherwise emitted during connection and disconnection.
Audio Remote Controller with Microphone
The supplied Audio Remote Controller with Microphone can be used to listen to audio playback. Combined with the headphone (sold separately), it can be used to receive phone calls. When the Audio Remote plug is inserted into the device, the microphone and speaker on the main unit will become inactive. Also, this microphone can be used as a recorder.
Headphone SEND / END button Play / Pause, FF, REW Switch

(sold separately)

Play a previous song

Play / Pause

Skip to the next song

Hold Switch

All other remote keys become inactive when HOLD is set. The SEND/END button is active.
Audio Remote Controller with Microphone Clip

Volume button

+ Adjust Volume
You can attach the Audio Remote Controller with Microphone to your pocket, etc., by using this clip.
Stop button Stereo headphone jack
During a call, it is not possible to adjust the volume with the Volume button. Use 3.5mm mini-plug type headphone to connect to the Audio Remote Controller with Microphone. This devices phone component can be used with the Audio Remote Controller with Microphone or as a speakerphone. Unlike conventional cell phones, it is not designed to be held against the head in conversation. Such unauthorized use of the phone, without an Audio Remote Controller with Microphone or other than as a speakerphone, is contrary to the design of this product and is not recommended. For instructions on how to use the phone with Audio Remote Controller with Microphone or as a speakerphone, please refer to page 61 of this manual.

Battery Charging

When using the device for the first time, set the Battery Switch to the supply side (see page 23), then fully charge the battery.

Charging the Battery

You can use two charging methods. When you connect the AC Adapter to the device, turn the power off. Connect the supplied AC Adapter to the cradle as shown in the figure below, and then insert the device into the cradle.
Connect the supplied AC Adapter to the device as shown in the figure below.
Note Charge the battery in an environment between 41F - 95F (5C and 35C). Temperatures outside this range may pause the charging process. Refer to page 24 for additional information on charging.
When charging the battery for the first time, or immediately after setting the battery switch to the supply side, fully charge the battery. If the battery is not fully charged, the remaining battery power will not be accurately displayed.
Maximizing the Battery Operating Time
Whenever possible, use the device with the AC Adapter especially when it is connected to your computer. Select the short powered-off time in the setting menu. This will shorten the time the unit will remain on if not used. See Customizing Your Device later in this chapter for more information. Turn off the front light. Set the screen brightness to power savings mode (front light off) or shorten the front light turn-off time. See Customizing Your Device later in this chapter for more information. For optimal performance use in an environment between 59F - 77F (15C and 25C). Anything outside this temperature range may decrease the operating time.

Battery Life

The built-in battery has a limited life that will gradually decrease after repeated charging. Replace the battery when you notice a dramatic decrease in battery performance.
Battery Charge Level and Stored Data Protection
If the battery charge level becomes extremely low or completely discharged, stored memory data will be deleted. As soon as the low battery status icon or the alarm message appears, immediately connect the AC Adapter to the device so it can charge. The battery gradually discharges even when not in use. If not used for a long time, it may completely discharge. It is strongly recommended that you save the devices memory data to your computer or a storage card. The manufacturer is not responsible for data changed or lost due to battery discharge. For back up, see Backing Up in Chapter 9.

Initial Setup

When using your device for the first time, completely charge the battery then follow the initial setup procedures below: 1. Press the Power button and when the welcome screen appears, tap the screen with the stylus to start the setup process. 2. When the align screen appears, follow the directions for adjusting the touch screen until the stylus screen appears. If a finger or any other object touches the screen during a correction, it will be cancelled. Repeat the correction procedure.
Note To display the align screen after the initial setup process, press the Record button while pressing the center of the navigation button, or by tapping , Settings, System, and then Screen.
3. Read and understand how to use the stylus, then tap Next.
Note See Using the Stylus on page 24 for more information.
4. Read and understand pop-up menu operation, then tap Next. Read the on-screen explanation and then operate the screen. Display the pop-up menus, and cut and paste the data according to the screen instructions. When this stage is complete, tap Next. 5. Follow the directions for setting the location, then tap Next. 6. When the complete screen appears, initial setup is finished. After tapping the screen, the Today screen will appear and the device will be ready to use. See Today Screen, later in this chapter for more information.

Setup Options

Method of Setting Card into SD Card Slot

Inserting a card:

1. Turn off the power. 2. Insert the card with its contact surface (metal contact surface) facing backward into the device.

Contact surface

Note An SD dummy card is loaded in the SD card slot at purchase. Remove the SD dummy card before inserting the card.

Removing a card:

1. Make sure that no application is accessing the SD card. 2. Turn off the power. 3. Lightly press down on the card until a clicking sound is heard. The card will pop out slightly from the slot. 4. Pull the card straight up to remove.

Connecting to a Computer

Before connecting your device to a computer, check the following. ActiveSync is on your computer. (For installation procedures of ActiveSync, see Quick Start Card.) The device is turned off. The computer youre connecting has an available USB port for the cradle.
To connect using the supplied USB cradle:
1. Connect the USB cradle to your computer as shown in the illustration below.

USB port

2. Insert the device into the USB cradle.
Make sure that the connector on the cradle is inserted into the port on the bottom of the device. Data can not be transferred if the connection is not made. When your device is properly inserted into the cradle, your device will turn on automatically and ActiveSync will automatically open on your computer.

Calendar Contacts Inbox Pocket Internet Explorer

Notes Tasks Pocket Excel

MSN Messenger

Pocket Word

In addition to the programs listed above, Windows Media Player, Backup, Calculator, File Explorer, Home, Infrared Receive, Microsoft Reader, Terminal Services Client, Watcher, Solitaire are pre- installed.
Note The program can be launched by using Home. See Home in Chapter 9.
Navigation Bar and Command Bar
The navigation bar, located at the top of the screen, displays the active program and time, and allows you to switch programs and close screens. The command bar at the bottom of the screen performs tasks in the open program, and includes menu names, buttons and the Input Panel button. Tap New to create a new item in the program.
Tap to view notification messages. Tap to change volume or mute the device. Tap to display the current date and the next schedule. Navigation bar. Tap to quickly select a program you have recently used. The program launched from Home is not stored here.

Tap to select a program.

Tap to see additional programs. Tap to customize the device.

New button.

Input Panel button. Command bar.

Menu names.

Buttons.
Note If you tap if you tap
on the right of the navigation bar, you can close that program screen. Also, on the navigation bar, you can close that screen.
To end the program, tap , Settings, System, Memory and Running Programs, and select the program you wish to end, then tap Stop. You can also end the program with Home.

Pop-up Menus

Pop-up menus provide quick access to select an action for an item, and vary with each program. To access a pop-up menu, tap and hold the stylus on the item you want to perform the action on. When the menu appears, lift the stylus and tap the desired action. Tap anywhere outside the menu to close it.
Tap and hold to display the pop-up menu. Lift the stylus and tap the action you want.
Tap outside the menu to close it without performing an action.

Notifications

Your device can remind you when you have an appointment or task scheduled, or serve as an alarm clock. Notification options include: A message box on the screen A sound (which you select) A flashing light To select reminder types and sounds, tap and then Settings. In the Personal tab, tap Sounds & Notifications. The selected options will apply for the entire device.

Entering Information

Options for entering new information include: Using the input panel to enter typed text. Writing or drawing pictures directly on the screen. Recording a message by speaking into the microphone. Using Microsoft ActiveSync to synchronize or copy information from your computer to the your device.

Changing memory allocation:
1. Tap , then Settings. On the System tab, tap Memory to display the Memory setting screen.

Slider.

Free space of the Program memory.
Free space of the Storage memory.
2. Drag the slider widthwise to adjust the memory allocation between Storage and Program. 3. When finished, tap OK.
Chapter 2: Basic Skills To confirm usage status of a storage card:
1. Tap , then Settings. On the System tab, tap Memory, then the Storage Card tab on the bottom.
Capacity of a storage card being inserted.
Free space. Capacity in use.
2. When finished, tap OK.

Releasing memory:

If memory is approaching full capacity, you can free up space by: Transferring data to a storage card or to your computer then delete it from your device. Deleting unnecessary files and programs. Quitting the program currently in use.
Note For more detailed information on operation method or the releasing memory, tap Help.
Chapter 3 Phone Functions Phone Functions
Chapter 3: Phone Functions

Using Phone Function

Launching Watcher
The Watcher program is used for the phone functions of your device. When the Radio Standby Switch is ON and Watcher is launched, the Watcher screen automatically is displayed when a call is received, even if you are currently using another program. 1. Turn the Radio Standby Switch (located on the left side) ON. Watcher will automatically launch and the phone can be used when the main screen appears.
Note When launched, a watcher status icon is displayed on the right part of the Today screen command bar.
As long as the Radio Standby Switch is ON, the Watcher screen will automatically appear when a call is received, even if the main unit is off. is operated by the Pocket PC operating system and the application programs on the device, pre-loaded and post-loaded. If the system get in such unusual case as when a button or tapping the screen does not respond, the phone functions are also unavailable, voice or data, outgoing or incoming. In such a case, please reset your device. See Chapter 10 (Resetting).

Ending Watcher

1. Turn the Radio Standby Switch OFF. Watcher will turn off and the screen will disappear. Do not quit Watcher during a call or communication.
Note When Watcher is OFF, the phone functions will not work even if the device is on.
If you turn the switch OFF while the device is OFF, the device will turn on automatically, and then the Watcher will turn off.

Dialing from the Call Log
1. Tap Call Log on the Tools menu. 2. Tap the number you want to dial and select Dial from the File menu, or press the center of the navigation button.
Note You can also place calls by tapping and holding the number you want to dial and selecting Dial from the pop-up menu. For details on the Call Log screen, see Call Log (page 71).

Redialing

1. Tap SEND on the VOICE tab screen to call the last number dialed.
Note The redial function does not work when there has been a missed call.

Receiving a Call

Depending on the settings, an incoming call is alerted with an audible sound, a flashing indicator, or a vibrating alert. 1. To answer a call, tap the SEND button on the device or the screen. Tapping CLR or the Volume button can mute the ringer tone. About Any-key Answer: When activated, Any-key Answer enables calls to be answered by tapping any button, other than the END, CLR or Volume buttons. This also includes the four program buttons on the front of the device. To set, in the VOICE tab screen, tap Tools, Options, and then scroll over to Voice at the bottom of the screen. For more information, see page 77.
About Caller ID: If a call is received from a number stored in the Pocket Outlook Contacts list, the name and number will be displayed. Unknown will be displayed if the caller is not on the Contacts list.
Note When END is tapped during an incoming call, it is rejected and the missed call icon appears.

Volume Control

Adjust the ringer volume by using the Speaker Icon on the navigation bar and the call volume (the speakerphone volume) by using the Volume buttons.
Tap to adjust the ringer volume.
Appears when Volume buttons are used. Speaker Icon button. Volume buttons.

Speaker Icon button:

The ringer type changes each time you tap the Speaker Icon button. The setting options in standby mode are Ringer Only, Ring and Vibe, Vibrate Only, and Silent Mode (Ring and Vibe Off). During a call, the setting switches between Sound on and Mute.

Volume buttons:

When you tap the Volume buttons, a volume bar appears on the screen to indicate the call volume level (6 levels excluding Mute). The call volume (the speakerphone volume) can be adjusted by tapping Tools on the VOICE tab screen, then Options, then Sounds at the bottom of the screen.

Call Waiting

When youre on the phone and another call is received, you hear a call waiting tone and Call Alert From appears on the display. 1. Tap SEND to put the original party on hold and switch to the new caller. When speaking to the new caller, the information for the first caller will not be displayed. 2. Tap SEND to switch to the original caller.

Call Forwarding

Call Forwarding transfers incoming calls to another phone number. Please contact your service provider about this feature.

Three-Way Calling

Three-Way Calling allows you to simultaneously talk to two callers at different phone numbers. Please contact your service provider about the availability of this feature. 1. When connected to one party, tap SEND and enter the second partys number, then tap SEND again. 2. When the second call is connected, tap SEND to talk to both callers. 3. Tap END to disconnect both parties.

Voice Mail

appears on the display when you have new voice mail. 1. Tap. 2. On the confirmation dialog screen, tap Yes. The phone connects to your voice mailbox. The voice mailbox phone number can be set at the Voice tab in Options. For details, see page 77.

Digital Numeric Page

When Digital numeric page is received, Numeric Page: XXX-XXXX appears on the screen. XXX-XXXX is numerical. The received Digital numeric page is saved as SMS in Inbox. To call the number, tap Messaging on the Tools menu, then select the Digital numeric page, then tap Call back Sender on the File menu.

Missed Call

appears if you do not answer a call. Tap END to turn off the missed call message.

Returning Missed Calls

To return the last missed call, tap SEND. When is tapped, the Call Log appears. This can be used to select a contact to call back. For details on the Call Log function, see page 71.
Note If the callers number is not identified, you cannot call back.

Link Dialing

With Link Dialing you can place calls require multiple inputs in a sequence of continuous operations. It is set when storing phone numbers in the Contacts of Pocket Outlook.

Link Dialing Storing

1. From the Today screen tap New then Contact. 2. Enter the phone number. 3. After the phone number, enter uppercase L or lowercase l, then the next number. 4. To enter more numbers repeat step 3. 5. Once all the numbers are entered, tap OK then start Phone Book in Watcher. 6. Tap Refresh on the command bar. The set number is read into Phone Book, and calls can now be placed from there using Link Dialing. Example: 604-323-

Using the Message List

Received messages are displayed in the message list - the most recently received are listed first.
Select the service and folder you want to display.
Select the sort order for messages. Tap to open a message. Tap and hold to display a pop-up menu of actions.
Tap to connect and to send and receive e-mail. Tap to connect to the selected service.
When you receive a message, tap it to open it. Unread messages are displayed in bold.
Tap to return to the message list.
Tap to delete this message.
Tap to view the previous or next message. Tap to reply to or forward this message.
To retrieve a full message during your next synchronization or e-mail server connection, tap and hold the message. On the pop-up menu tap Mark for Download. Specify downloading preferences when you set up the service or select your synchronization options. Inbox synchronization options can be changed using ActiveSync options. See ActiveSync Help for more information. To change options for e-mail server connections, tap Tools then tap Options. On the Service tab, tap the service you want to change. To remove a service, tap and hold the service and select Delete.

Composing Messages

1. Tap New. 2. In the To field, enter the e-mail addresses of the recipients, separating the names with a semicolon, or select a name from the contact list by tapping and holding To, or by tapping the Address Book button.

Tap to send the message.

Tap to show or hide. the complete header.
Tap to show / hide the recording toolbar. Tap to display the Address Book. Tap to insert common messages.
3. Compose your message. To enter preset or frequently used messages, tap My Text and select a message. 4. Tap Send when youve finished the message. If you are working offline, the message is moved to the Outbox folder and will be sent the next time you connect.
Managing E-mail Messages and Folders
Messages are displayed in one of five folders: Inbox, Deleted Items, Drafts, Outbox and Sent Items. The Deleted Items folder contains messages that have been deleted on the device. The behavior of the Deleted and Sent Items folders depends on the options you have chosen. In the message list, tap Tools then Options. On the Message tab, select your options. To create new folders, tap Tools then Manage Folders. For all service except ActiveSync, you can access folder options by tapping Tools then Manage Folders. To move a message to another folder, tap and hold the message and then tap Move to on the pop-up menu.
Folder behavior with a direct connection to an e-mail server
The behavior of the folders you create depends on whether you are using ActiveSync, POP3, or IMAP4: If you use ActiveSync, e-mail messages in the Inbox folder in Outlook will automatically be synchronized with your device. You can select to synchronize additional folders by designating them for ActiveSync. The folders you create and the messages you move will then be mirrored on the server. For example, if you move two messages from the Inbox folder to a folder named Family, and you have designated Family for synchronization, the server creates a copy of the Family folder and copies the messages into that folder. You can then read the messages while away from your computer. If you use POP3 and you move e-mail messages to a folder you created, the link is broken between the messages on the device and their copies on the mail server. The next time you connect, the mail server will see that the messages are missing from the device Inbox and delete them from the server. While this eliminates duplicate copies of messages, you will no longer have access to messages moved to folders created anywhere except the device. If you use IMAP4, the folders you create and the e-mail messages you move are mirrored on the server. Therefore, messages are available to you anytime you connect to your mail server, whether it is from your device or computer.

Tap View to select Text Color. Tap Tools for Tab Settings or About.
Note Tap and hold anywhere on the Running tab, except the application names, and Stop All appears in the pop-up menu.
Activate, Stop and Stop All of the running application can also be operated with Memory of System tab of Settings.

Display Icon List

The following list shows the tabs and icons for the initial setup.
Tabs Icons Applications Tabs Icons Applications
Running Main Watcher Pocket Internet Explorer Windows Media Player Notes Tasks Inbox Calendar Contacts Pocket Word Pocket Excel Calculator
Front Light Power File Explorer Backup Infrared Receive Microsoft Reader MSN Messenger

Solitaire

Moving an Application Icon into Another Tab
A moved icon appears next to the last icon in its new location. It cannot be moved to a tab that already contains 18 icons.
To move using pop-up menu:
1. Tap and hold the icon to be moved. 2. Tap Cut on the pop-up menu. 3. Tap the destination tab, then tap Paste on the Edit menu.
Note You can also select Paste from the pop-up menu displayed by tapping and holding any portion other than the icon.
To move using drag and drop:
Tap the icon you want to move and drag it to the destination tab, after the tab name is highlighted, drop it. The icon is transferred and deleted from its original location.
Note If the icon is dragged and dropped in the same tab, it will return to its original position on the tab screen.

Deleting an Icon

1. Tap and hold the icon to be deleted. 2. Tap Drop on the pop-up menu.
Note You cannot delete the Watcher icon.

Adding an Icon

Application and file icons can be added to the Home screen. 1. Tap Edit, then Add to display the Add Application screen. You can also select Add from the pop-up menu displayed by tapping and holding any portion other than the icon. 2. Tap w of Application file to show the file list. If there is no desired file on the file list, you can find it by tapping Browse. To refer to all folders and files, tap Browse to show the Browse Dialog screen. When the file is selected, its name is displayed in the Application file box.
Tap to designate a folder you want to browse. When a storage card is inserted, files or folders contained in the storage card are displayed from the top directory. Tap to move up one level in the directory folders.
Tap to select kinds of application or file to be browsed.
If a file is selected from the list, the screen returns to the Add Application screen.
3. Enter an icon name (up to 32 characters) in the Application name box that will display on the Home screen. 4. Tap OK when finished.
Note A new icon cannot be added if the Application file is not designated or if the Application name is not entered.

Note If your device memory becomes short of its capacity during restore, the restore process stops. Increase the memory allocation of the main memory of your device (see Setting Memory in Customizing Your Device in Chapter 2), then restart the restore procedure.

Deleting a Backup File

1. Insert the storage card, which contains backup data to be deleted. 2. Tap , Programs, then Backup to display the Backup screen. 3. Select Delete Backup File from Functionality.
4. Tap OK to display the Delete Backup File confirmation screen. 5. Tap OK to delete the backup file.
Chapter 10 Additional Information
Chapter 10: Additional Information

Resetting

Reset is equal to Restart on a computer. Reset only in unusual circumstances such as when the screen freezes and doesnt respond to tapping. Information not saved prior to resetting will be deleted. When your device is reset, phone functions are ended. To reset, press and release the Reset Switch while the power is on. Once reset, the Today screen appears.
Note If the function cannot be restored even after resetting, initialize your device (see Clearing Memory on the next page).
When the power is on, press the Reset Switch with the stylus, then release. By doing so, reset is made and the Today screen appears.
Clearing Memory (Initialization)
Initializing the device returns it to the status when it was originally purchased.
Note Initializing the device deletes all stored data, except built-in programs.
Before initialization, we recommend storing the memory data of the device into your computer or a storage card. Before initialization, remove a storage card.

To initialize:

1. Turn off the power. 2. Press the Power button while pressing and holding the Reset Switch with the stylus, then release the Power button. 3. Release the Reset Switch. When initialization is complete, the welcome screen appears. Proceed with setup.

Specifications

External dimensions Operating conditions 3 in. x 5 in. x 3/4 in. (excluding protrusion part) (77.5(W) x 127.5(H) x 19.5(D) mm) Temperature: 32F to 104F (0C to 40C), Humidity: 30 to 80% RH Temperature capable of charging: 41F to 95F (5C to 35C) (According to the operating status, the charging may pause even when the ambient temperature is below 95F (35C).) Advanced Lithium Ion battery Intel StrongARM SA-1110 206MHz 32MB SDRAM Reflective color TFT, 240x320 pixels, 65,536 colors Possible to insert SD memory card or SDI/O card Note: The security function of the SD memory card is not usable. Data encrypted by the SD memory card security function-compatible equipment is not usable. Infrared port Stereo headphone jack Cradle connection port AC Adapter jack AC Adapter INPUT: 100-240V AC, 0.36-0.2A, 50-60Hz OUTPUT: 5V DC, 3A An attached Power Supply Cable is a 125 V AC type. Based on IrDA Ver.1.2, Maximum data transmission speed: 115 kbps 2.5mm, five poles stereo mini plug

When you enter letters that are on the same number key, you must pause after entering the first letter and wait until the underline disappears before entering the next letter so your Smartphone can process the first letter. This pause is called the Multipress time-out, and you can adjust the length of the pause between keypresses. For example: To enter the word "cat," press 222, pause, press 2, and then press 8. Press the # key to move a space. To enter punctuation in Multipress mode, press 1 repeatedly until you see the punctuation mark that you want. To change the Multipress time-out:
1. Select Settings from the Start menu. 2. Select Accessibility. 3. In the Multipress time-out field, select the length of the pause between keypresses that you prefer. 4. Press the Left Softkey (Done) to save the settings and return to the Settings screen.

T9 Mode

When you are in the T9 mode, just press the number keys that contain the letters that you want to form a word. T9 will then analyze your keypresses and attempt to complete the word. For example: To enter the word "shoe," press 7, 4, 6, 3. To enter text in T9 mode:
1. Press and hold the * key until the input menu appears. Scroll down and choose English. The T9 indicator should appear at the top of the display. 2. Enter letters by pressing the keys on which the letters appear. Press a key only once for each letter. 3. Press the # key to accept the word and enter a space after it, or press the Down button on the Navigation Pad to scroll through the other word options; press the Action button to accept the word choice. 4. Press 1 and then press the Up or Down button on the Navigation Pad to cycle through common punctuation symbols.
NOTE: T9 cannot always find the word you want in the T9 dictionary. In these cases, switch to Multipress mode. After you have entered the word in Multipress mode, the word will be added to the T9 dictionary.

Numeric Mode

When you are in the Numeric mode, just press the number(s) you want to enter on the keypad. If a field permits a numerical entry only, such as the Work phone number field in Contacts, the input mode will automatically default to Numeric mode.

Unknown Photo: This photo will display whenever the phone number of the incoming call is not known to Caller ID because no phone number was passed in to your Smartphone. This would occur if the person calling you has blocked their phone number from being displayed to the receiver, or has not enabled the broadcast of their Caller ID. Not-found Photo: This option in the Set Default Photos screen lets you assign a generic Photo ID to any incoming call from a person whose number is not found in your Contacts. That is, the phone number of the incoming call is known, but has no matching entry in your Contacts. Default Photo: This photo will display when the incoming call is found to be from a matching entry in your Contacts database, but there is no user-assigned Photo ID for either that individual Contact entry, or for the Group it belongs to. Display Settings Selecting this from the Options submenu opens the Display Settings screen, which allows you to specify whether the Photo ID should consist of only a photo (Use Photo Only), or a photo merged with a template (Use Template). Options available in this screen will depend on which of these is active in the Display Style field. General Opens a screen that contains two options:
Storage Path for Re-sized Photos: Every time you use Assign Photo to assign a photo, Caller ID will automatically copy and re-size the original photo file. You can then delete the original file, if you wish to save valuable storage space in the phone. The Storage Path for Resized Photos field allows you to specify whether you want these re-sized photos to be saved to your Smartphone or to your Storage Card. Display Photo During Incoming or Waiting Call: Active by default. If you uncheck this checkbox and then select Done, Photo Contacts will be disabled. The phone will recover its original background image for incoming calls, and the Incoming Call monitor will be unloaded from memory. No photos will display when the checkbox is not checked.
Assigning a Photo ID to a Contact
The Assign Photo command lets you assign an image file or animated GIF file (Photo ID) to an individual Contact entry stored in your Pocket Contacts, or Phonebook entry on the SIM card. You can also specify a size, and a position for the Photo ID. And, to add more fun and a stronger visual impact to your incoming calls, you can assign an animated template ID, which will serve as a frame around the image, if desired. Templates are animated GIF files, and are available in both Portrait and Landscape orientation. You can choose to display the Photo ID only, or the Photo ID together with a template ID, and easily change Photo IDs and/or Template IDs at any time. A collection of templates are included in the \\Storage\My Documents\IA Caller ID Photos folder of your Smartphone. NOTE: The steps in this section are for the Assign Photo command on the main menu (individual Contact assignment), but this same basic procedure can also be followed when:

Capturing a video using Video mode
Select Camcorder from the Start Menu to go directly to Video capture mode. If already in a different capture mode, open the menu and select Video from the Capture Mode submenu, or press 1 on your phone keypad to switch to different modes. The Capture Size dimensions are shown at the upper left of the screen. Press 2 on your keypad to select the size (176 x 144, or 128 x 96). Press the navigation pad Up if you want to Zoom In, or Down to Zoom back out. To specify the output format, select Options from the menu and then Modes. In the Encoder field, select either MPEG4, H.263, or Motion-JPEG AVI. Also in this screen, you can set a limit to the video file size, if desired. Select Options > Video to specify whether or not to capture audio to accompany the video clip, and to change the default filenaming convention if desired. As a shortcut, you can press the 6 button on your phone keypad to toggle audio-capture capability On and Off. An icon resembling a microphone in the lower right of the Video Capture screen indicates whether audio capture is enabled or disabled. When Off, a diagonal line is drawn through the icon, as shown below. Audio recording enabled Audio recording disabled
The amount of time available for your next video capture, according to available memory and your current settings, is always displayed. To begin capturing a video clip, press the Camera button on the right side of your Smartphone, or the Left Softkey (Capture), or the Action button. Press any of them again to stop recording. If a limit has been set for the video file size, recording will stop automatically when the limit is reached.
Capturing a video using MMS Video mode
The usage and options for MMS Video capture mode are the same as for Video capture mode, except for the following: Whereas the Video capture mode allows you to set any file size limitation, MMS Video mode is permanently set to a file size limitation of 95 KB. When the video currently being recorded reaches a file size of 95 KB, the recording process will automatically stop. In addition, when in MMS Video mode, there are only two choices for Encoder type: MPEG-4, and H.263. Typically, it is recommended that you use H.263 for video files to be sent as MMS attachments.

Using Photo ID mode

The Photo ID capture mode captures a still image in the same way as Photo capture mode, but captures at a size (176 x 180) which is convenient to use directly as a Photo ID for one of your contacts. Immediately after capturing an image using Photo ID capture mode, you can select Save As > Caller ID Photo from the menu in the Review screen (shown later in the section entitled The Review screen) to invoke the Caller ID (Photo Contacts) application. In Caller ID, all entries in your Pocket Contacts will be listed. Select the Contact to which you want to assign the image you just captured. Then press the Left Softkey (Next) and then again (Done) to assign the photo. After that, you will be returned to the Capture screen of Capture mode automatically.
Using Picture Theme mode to frame your captured photos
The Picture Theme capture mode lets you place your captured images into selected frames. When in Camera mode, select Capture Mode > Picture Theme from the menu, or press 1 on your keypad until Picture Theme is the active capture mode. When you switch to Picture Theme, one of your templates in the \My Documents\Frames folder will be loaded. To load a different template, press the navigation pad Left or Right; or select Select Template from the menu to browse and preview each template. The file name, dimensions, and number of images required for that template will be displayed in the Select Template screen, as shown below on the left. The figure on the right below shows the Picture Theme capture mode, ready to capture an image. The incoming video stream is previewed in the place holder where the captured image will be placed (in this example, its the place holder on the left). Note that (1/2) is displayed in the lower right of the screen. This indicates that the next image captured will be the first one; no images have been captured yet.
In templates that require two or more images, the focus switches to another place holder after the first one is filled. To capture an image, press the Camera button on the right side of your Smartphone, the Left Softkey (Capture), or the Action button. The image will be saved with the frame. As with other still images, it will be placed in the \My Documents\My Photos folder. Zoom capability is determined by the currently loaded template, as shown later in the table in the Zooming in and out section.

Smartphone User Manual NOTE: While you are connected to the Internet, you can change between Pocket Internet Explorer and other programs on your Smartphone by pressing the Home key and invoking the program you want. This does not close your Internet connection. Subsequently returning to Internet Explorer in the same phone session would re-display the most recently opened Web page. (To terminate the Internet Explorer program, you can use the Task Manager utility explained in Chapter 9.) Using the Favorites list If you see a Web page you want to visit another time, mark it as a favorite. The next time you want to visit that Web page, you can select it from your Favorites list. If you select Add Favorite from the menu when the desired Web page is open, the name and URL of the current page is already filled in. You can edit the Name field and/or Address (URL) field if necessary. If you previously created additional folders, select a folder in the Folder field. Then select Add to add it to your Favorites. By default, only the Favorites folder exists. To create a new folder in which to place URLs, select Add Folder from the menu in the Favorites screen. To edit the Name, Address (URL), or Folder fields of an existing entry in your favorites, select the desired Favorite in the list, then select Edit from the menu. To delete a favorite, select Delete. Customizing Pocket Internet Explorer You can customize Web browsing options, change the network to connect to, and make more memory available on your phone by clearing stored cookies and Web pages. Select Options from the menu, then select either General, Connections, or Memory.

5.3 Bluetooth

Bluetooth is a short-range wireless communications technology. Devices with Bluetooth capabilities can exchange information over a distance of about 30 feet (10 meters) without requiring a physical connection. Unlike infrared beaming, you don't need to line up the devices to beam information with Bluetooth. The devices only need to be within a range of about 10 meters. You can even beam information to a device in a different room, as long as it's within range. The software included with your Smartphone allows you to use Bluetooth to beam information such as files, contact cards, appointments, and tasks to other Bluetooth-enabled devices.

To set up an E-mail account:
1. When in the Home screen, select Start > Messaging. 2. Select Outlook E-mail > Menu > Options. 3. Select Account Setup > Menu > New. 4. Enter your display name for this E-mail account, and your E-mail address, and select Next.
Smartphone User Manual 103 NOTE: Before configuring E-mail on your Smartphone, you must have an Internet and E-mail account. You will also need to configure your Smartphone's data connection, as described in Chapter 5.
5. In E-mail address, enter the address for this account. Leave the Automatic setup box checked to obtain E-mail setting from the Internet. Your Smartphone will make an Internet connection and attempt to determine the server settings for E-mail. 6. In User name, enter your user name. This is usually the first part of your E-mail address, which appears before the "at" sign (@). 7. In Password, enter your password. 8. In Domain, enter the domain name, if required. 9. To save your password, so that you do not need to enter it each time you connect to your E-mail server, select Save password > Next.
NOTE: If you save your password and then lose your phone, your E-mail could be accessed by someone else.
10.In Server type, scroll to select the type of E-mail server that hosts your mailbox (IMAP4 or POP3) and select Next. In Account name, enter a name for this account. You must use a different name for each account that you set up. 11. In Network, scroll to the type of network that your E-mail server runs on and select Next. 12.Enter information about your E-mail servers and select Next. If you are not sure what to enter, ask your network administrator. 13.Select message download options and select Next. 14.Select a connection option, then select Next > Finish.
104 Smartphone User Manual

6.2 Managing Accounts

Use and manage up to eight messaging accounts with your Smartphone. Viewing the list of accounts In the Home screen select Start > Messaging. The list of accounts that display the number of unread messages in the Inbox of each account is shown in parentheses. Moving between accounts If you have an account open, you can quickly switch to another account by scrolling right or left, or selecting Menu > Switch Accounts. Changing E-mail account options In the Home screen, select Start > Messaging and then select an account. Select Menu > Options and then select the type of option to change. Select Done to confirm. Deleting an account In the Home screen, select Start > Messaging, and then select an account. Select Menu >Options > Account Setup. Scroll to an account and then select Menu > Delete.

112 Smartphone User Manual
6.5 Viewing Message Folders
Each messaging account has a set of folders in which your Smartphone stores messages for that account. Deleted Items: contains messages that you have marked for deletion. Drafts: contains messages that you have saved before sending. Inbox: contains received messages. Outbox: contains sent E-mail messages awaiting synchronization, or messages that will be sent upon the next E-mail server connection. SMS messages are sent immediately over the network and appear in your SMS Outbox folder only for a few seconds. Sent Items: contains copies of sent messages. You can move a message to a different folder within the same account. When you synchronize or send and receive E-mail, your Smartphone synchronizes any additional E-mail folders that you have created in Outlook on your desktop computer or on your E-mail server. It also synchronizes the messages contained in those folders, if the folders are marked for synchronization. To view message folder contents:
1. From the Home screen, select Start > Messaging. 2. In the Messaging screen, choose the account. 3. Select Folders from the menu. 4. From the list of folders, select the folder you want to view, then press the Left Softkey.
Smartphone User Manual 113 Moving a message to a different folder: From the Home screen, select Start > Messaging. Choose the account and scroll to the message to move. Select Menu > Move. Select the folder into which to move the message. To empty the deleted items folder:
1. From the Home screen, select Start > Messaging. 2. Select Menu > Folders. 3. If necessary, scroll right or left to switch to the account for which to empty the Deleted Items folder. 4. Select Folders > Deleted Items. 5. Select Menu > Empty Folder.
114 Smartphone User Manual

6.6 Managing Messaging

All E-mail and SMS messages are stored in the respective Inbox of each account in Messaging. By default, the most recently received messages are displayed at the top of the Inbox list. Using the menu options, you can customize your Inbox settings to control the way you send, receive, and view messages.
Using Messaging menu options
It is easy to accomplish common messaging tasks from your Inbox. Press the New softkey to compose a new message, or press the Menu softkey to forward, delete, and reply to messages. Inbox options allow you to customize and manage your messages. To view messaging menu options: In the Home screen, select Start > Messaging. Choose the account and then press the Menu softkey.
Smartphone User Manual 115 The following table lists the Messaging functions found under Menu: Messaging Option Delete Reply Reply All Function Delete the selected message. Reply to an open or selected message. Reply to the sender and all other people who received a copy of the open or selected message. Forward the selected message to another E-mail address. View the folders in this account. Switch between this account and another. Move the open or selected message to another folder. Display the header text of a message in your Inbox in light type, indicating that the message has been read. Retrieve the entire E-mail message from the E-mail server the next time you connect. Display a list of Inbox options that you can customize. Connect to your E-mail server to send and receive messages.

1. From the Home screen, select Start > Messaging > MSN Messenger > Sign In. 2. In Sign-in Name, enter the sign-in name that you use for Hotmail or your.NET Passport (Example: name_ 123@hotmail.com). 3. In Password, enter your Hotmail or.NET Passport password. 4. Select Remember my password if you don't want to enter your password again in the future. 5. Select Sign In. 6. To sign out, select Menu > Sign out.
NOTE: If you do not sign out of MSN Messenger, you will remain on a data connection. This may result in additional charges from your service provider. Adding an MSN Messenger contact: In the MSN Messenger contacts list, select Menu > Add Contact. Add the Hotmail or.NET Passport sign-in name of a person with whom you want to chat. Their sign-in name is added to the contacts list.
Smartphone User Manual 119
Deleting an MSN Messenger contact: In the MSN Messenger contacts list, select the contact. Select Menu > Delete Contact. Sending an instant message: Sign in to MSN Messenger. Scroll to the contact with whom you want to chat. Select Menu > Send Message. Enter your message and select Send. This starts a chat with the contact. To reply to an instant message:
1. Select Menu > Chats. 2. Select the name of the person sending the instant message. The message displays, along with a box for your reply. 3. Enter your reply and select Send. If you want to be able to receive instant messages at any time your phone is connected to a network, select Menu > Options > Passport Account > Run this program when connection is available > Done.
Inviting a contact to an ongoing chat: From a chat, select Menu > Invite and then choose a contact. The contact receives an instant message and can join the chat.
120 Smartphone User Manual Changing between chats: Select Menu > Chats. In the list of ongoing chats, select the name of a contact with whom to chat. Return to the contacts list: From a chat, select Menu > My Contacts. Ending a chat: Select Menu > End Chat. Seeing who is already chatting: Select Menu > Chats. Blocking or unblocking an MSN Messenger contact: In the MSN Messenger contacts list, select the contact's name. Select Menu > Block. The contact will no longer be able to see your status or send you messages. To unblock the contact, select Menu > Unblock. Changing your status: In the MSN Messenger contacts list, select your name. Select a status description, such as Away. This status is displayed next to your name in the contact lists of your contacts. Change your display name: In the MSN Messenger contacts list, select Menu. Select Options > Passport Account. In My display name, enter your name as you want it to display in the contacts lists of your contacts.

1. Select Messaging from the Start menu. In the Messaging screen, select Media Messages. 2. Press the Left Softkey (New). 3. An empty message screen will appear. In the To field, enter the recipients phone number or E-mail address. You can enter it manually, or press the Action button or select Insert Contact from the menu, to choose a person from your Contacts. In the Subj field, enter a subject.
124 Smartphone User Manual
To insert a Photo or Video file:
a. In the screen shown on the previous page, select the Insert Picture/Video. box. (If necessary, press the Up or Down button on the navigation pad to select.) b. Press the Action button. All of your available photo and video files will be displayed in a Thumbnail view. c. Highlight the photo or video you want to attach, and press Select.
In addition, the menu (Right Softkey) accessed from the Select Media screen contains the following commands: Select Inserts the currently highlighted photo/video into your message. Play/Open Plays the highlighted video or opens the highlighted photo. Information Displays various data about the selected file. Delete Removes the selected file.
Smartphone User Manual 125
Capture Picture Lets you take a new picture using your Smartphones built-in camera, and attach it to the MMS slide. Capture Video Lets you capture a new video clip using your Smartphones built-in camera, and attach it to the MMS slide. List View/Thumbnail View Toggles the display between List View (basic file list) and Thumbnail View (thumbnails of the files). Change Folder Lets you choose a different folder from which you can select a photo or video to add to your message.

To insert text:

Select the Insert Text. portion of the screen and manually enter the desired text. If you want to save text you have entered (for re-use in a later message), you can press the Right Softkey to open the menu, then select Save to Canned Text. Or, if you want to insert previously-saved text, select Insert Canned Text from the menu. The Canned Text screen will open. Choose the text you want, then press the Left Softkey (Select) to insert it.
126 Smartphone User Manual
In addition, the menu (Right Softkey) accessed from the Canned Text screen contains the following commands: Select Inserts the currently highlighted canned text into your message. New Lets you create a new canned text word or phrase. Type in the text, and then press Save. Edit Allows you to modify the currently selected canned text. Delete Removes the currently selected canned text from the choices available in the Canned Text screen.

174 Smartphone User Manual Menu Commands in List View You can perform many additional file management functions using the commands on the menu when in List View, as follows: File Selecting File opens a submenu that lets you create a New Folder which will be a subfolder under the current folder; or Rename, Copy To, Move To, or Duplicate the currently selected file(s). Selecting Associate on the File submenu allows you to associate all files that have the same extension as the selected file with a specific application program. Then whenever you select a file of the associated file type, it will open using the application you specified. Even if a particular file type is already associated with a particular application, you can perform a one-time override of that default association using the Open With command on the File submenu. It allows you to select a file, and then individually select the application that you want to open the file with. Create Shortcut on the File submenu enables you to create a shortcut for a file and place it in any folder. First, select the file for which you want to create a shortcut, then select Create Shortcut and select the folder where you want it to be placed. Zip Extraction This command lets you unzip (extract) ZIP files that you may have received into your Smartphone via ActiveSync, infrared beaming, E-mail, etc. First, select the desired file (filename must have an extension of.zip). Then select Zip Extraction. This opens a submenu containing the Contents and Extract Here commands.
Smartphone User Manual 175 Select Extract Here from the submenu if you just want to extract all the files immediately and place them in the current folder. Selecting Contents from the submenu will list all the files contained in the selected ZIP file. In the screen listing the individual files, you can open a menu containing several options. Among them are:
Extract To If you dont want all files in the list to be extracted, you can first select only the files you want. Then select the folder/subfolder where you want to place the extracted files and press the Left Softkey (Extract). Integrity Test This command checks to see if the data contained in all of the individual files (contained in the current ZIP file) is correct. View This command is available when only one individual file or one folder is selected. If an individual file within the ZIP file is selected, then the View command invokes the application associated with that filetype and displays the file. If the ZIP file contains folders, and one of the folders within the ZIP file is selected, then the View command will open the folder and display a list of the files within it. A plus sign (+) will be shown in front of encrypted items in a ZIP file.

186 Smartphone User Manual After checking the desired checkboxes in the previous figure, press the Left Softkey to begin the Erase process. You will still be given an opportunity to confirm the deletion of each category individually. Note that only the categories listed in the previous figure will be erased. MMS messages are not deleted. Refresh Selecting Refresh on the menu, pressing the asterisk (*) shortcut key, or pressing the Left Softkey in the main screen, updates and re-displays the amounts of Used Storage and Free Storage. Whenever you use any of the Erase commands on the menu, the Refresh operation will be performed automatically to show you the new storage amounts resulting from the deletion.
188 Smartphone User Manual

Regulatory Notices

Agency Identification Numbers
For regulatory identification purposes, your product is assigned a model number of ST20B. The Battery Pack has been assigned a model number of ST26A and ST26B. To ensure continued reliable and safe operation of your Smartphone, use only the accessories listed below with your ST20B. NOTE: This product is intended to be used with a certified class 2 limited power source, rated 5 volts DC, maximum 1A power supply unit.

European Union Notice

Products with CE marking comply with the R&TTE Directive (99/5/EC), the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms (in brackets are the equivalent international standards):
EN 60950 (IEC 60950) - Safety of Information Technology Equipment. ETSI EN 301 489-7 - Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) for radio equipment and services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS).
Smartphone User Manual 189
ETSI EN Global System for Mobile communications (GSM); Harmonized standard for mobile stations in the GSM 850 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC). ANSI/IEEE C.95.1-1992- specific absorption rate in mobile phone emission condition for body health. FCC part 15 - Radio Frequency Devices and part 24 Personal Communications Services. EN 50360 - 2001 Product standard to demonstrate the compliance of mobile phones with the basic restrictions related to human exposure to electromagnetic fields (300 MHz 3 GHz). SAR value: FCC (1g) Head 0.611W/kg; Body 1.340W/kg. CE (10g) Head 0.297W/kg; Body 0.619 W/kg. ETSI EN 301 489-1 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements. ETSI EN 301 489-17 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2.4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment.

194 Smartphone User Manual
Exposure to Radio Frequency (RF) Signals
Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on the safety standards previously set by both U.S. and international standards bodies:
American National Standards Institute (ANSI) IEEE.

C95.1-1992

National Council on Radiation Protection and Measure-
ment (NCRP). Report 86. 1986 Protection (ICNIRP) 1996
International Commission on Non-Ionizing Radiation Ministry of Health (Canada), Safety Code 6. The standards
include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.
Smartphone User Manual 195 The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6W/kg. In the U.S. and Canada, the SAR limit for mobile phones used by the public is 1.6 Watts/kg (W/kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in usage. Normal conditions only ensure the radiative performance and safety of the interference. As with other mobile radio transmitting equipment, users are advised that for satisfactory operation of the equipment and for the safety of personnel, it is recommended that no part of the human body be allowed to come too close to the antenna during operation of the equipment.
WARNING: Your Smartphone contains a Lithium ion battery pack. There is a risk of fire and burns if the battery pack is handled improperly. Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. Do not attempt to open or service the battery pack. Replace only with the battery pack designated for this product. Recycle or dispose of batteries properly. Do not discard with your regular trash.
196 Smartphone User Manual
Telecommunications & Internet Association (TIA) Safety Information
Pacemakers The Health Industry Manufacturers Association recommends that a minimum separation of six inches be maintained between a handheld wireless phone and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with the independent research by and recommendations of Wireless Technology Research. Persons with pacemakers: Should ALWAYS keep the phone more than six inches from their pacemaker when the phone is turned ON.
Should not carry the phone in a breast pocket.
Should use the ear opposite the pacemaker to minimize the potential for interference. If you have any reason to suspect that interference is taking place, turn your phone OFF immediately. Hearing Aids Some digital wireless phones may interfere with some hearing aids. In the event of such interference, you may want to consult your service provider, or call the customer service line to discuss alternatives. Other Medical Devices If you use any other personal medical device, consult the manufacturer of your device to determine if they are adequately shielded from external RF energy. Your physician may be able to assist you in obtaining this information. Turn your phone OFF in health care facilities when any regulations posted in these areas instruct you to do so. Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

n A warning message about Running out of memory pops up on the screen.
n I cannot open an image or video file.
The file type of the image or video may not be supported. See Chapter 3 for a list of all supported image/ video file formats. When in the Camera screen, you can adjust for different lighting conditions by selecting Ambience from the menu and then selecting an effect, and/or Adjust View properties.
n The image appears dark when using the camera.
200 Smartphone User Manual
ActiveSync Problems Problem
n ActiveSync operation cannot be performed or connected.
Make sure the mini USB cable is connected securely. Make sure you have installed the ActiveSync software found on the Companion CD that came with your phone. Make sure the settings are correct in File Menu > Connection Settings. in the Microsoft ActiveSync window on your desktop computer. Chapter 7 discusses ActiveSync. If still not working, try to uninstall the ActiveSync software (using Control Panel on your desktop computer), then reinstall.
Smartphone User Manual 201
n ActiveSync is connected, but data or information cannot be transferred.
Check Tools Menu > Options. in the Microsoft ActiveSync window on your desktop computer to see if the information type you want has been selected for synchronizing. See more details about ActiveSync in Chapter 7.
n I cannot perform over-the-air synchronization.
Ensure that Microsoft Mobile Information Server has been installed.
202 Smartphone User Manual
Connection Problems Problem
n Unable to use Infrared (IR) to transfer information.
Try the following: Transfer only one file, or no more than 25 contact cards, at a time. Line up the IR ports so that they are unobstructed and within close range. Make sure nothing is between the two IR ports. Adjust the room lighting. Some types of light interfere with IR connections. Try moving to a different location or turning off some lights. Do not try to use infrared beaming in the sunlight. Try the following: Ensure that you have set up and connected to an Internet Service Provider. Ensure that the wireless connection to your mobile Service Provider is switched on and that the signal is unobstructed. Verify with your Internet Service Provider that your user name and password are correct.