Tools and Supplies You will need these tools and supplies to install your UV8: Torx type, flat-head and Philips screwdrivers Wire cutters and strippers Tools to remove existing radio (screwdriver, socket wrench set or other tools) Electrical tape Crimping tool Volt meter/test light Crimp connections 18 gauge wire for power connections gauge speaker wire Disconnecting the Battery To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
NOTE: If the UV 8 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.
WARNING! Only connect the unit to a12-volt power supply with proper grounding. WARNING! Never install this unit where operation and viewing could interfere with safe driving conditions. WARNING! To reduce the risk of a traffic accident (except when using for rear view video camera) never use the video display function while driving the vehicle. This is a violation of federal law. WARNING! Never disassemble or adjust the unit. WARNING! To prevent injury from shock or fire, never expose this unit to moisture or water. WARNING! Never use irregular discs. WARNING! To prevent damage to the mechanism inside this unit, avoid impact to the TFT monitor. WARNING! Using an improper fuse may cause damage to the unit and result in a fire. WARNING! The monitor employs an automatic motorized mechanism. To prevent damage to the core mechanism, please do not push, pull or swivel the monitor manually.
INSTALLATION Pre-installation 1. Press the metal levers on both sides to remove the halfsleeve from the radio.
2. Install the half-sleeve. a. Install adapter if necessary (optional). b. Install half-sleeve into adapter or dashboard (use only the supplied screws). Do not force the sleeve into the opening or cause it to bend or bow. c. Locate the series of bend-tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard. d. Install support strap to make the unit more stable.
CAUTION! Be careful not to damage the car wiring. 3. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Wiring Complete wiring as illustrated in the wiring diagram on page 51. Once the wiring is complete, reconnect the battery negative terminal. If there is no ACC available, connect the ACC lead to the power supply with a switch. NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The UV 8 uses one 15 amp mini-ATM fuse, located in the black filter box in-line with the main wire harness. Final Installation After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.

1. Connect wiring adapter to existing wiring harness. 2. Connect antenna lead. 3. Carefully slide the radio into the half-sleeve, making sure it is right-side-up, until it is fully seated and the spring clips lock it into place.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 20 of horizontal. Make sure the unit is mounted within this limitation. 4. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary. CAUTION! The rear of the radio must be supported witht he strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. 5. Replace any items you removed from the dashboard.
Final ISO-DIN Installation 1. Remove trim ring. 2. Mount factory brackets on new radio using existing screws from old radio. 3. Slide radio chassis into dash opening and secure. 4. Reinstall dash panel.

Wiring Diagram

CONTROLS AND INDICATORS Button Operation 1. OPEN/CLOSE Press to activate the automatic mechanical system and move the TFT monitor into viewing position. Press again to close the TFT. 2. WIDE/DISP Press to adjust the display aspect of the picture to one of two settings: Full or Normal. With the monitor closed, press the DISP button to cycle through information available on the LCD screen. 3. PIC/AS/PS Press to adjust the Brightness and Contrast. Press the AUDIO button (5) to move between Brightness to Contrast. Turn the rotary encoder (5) to adjust the setting for the selected option. With the monitor closed, press AS/PS to automatically store strong radio stations in the six preset channels in the current band. 4. TILT/BAND Press to activate the tilt function. Use the joystick to make adjustments while the yellow tilt icon is flashing. Press once to adjust the downward tilt angle of the screen one step at a time or press and hold to adjust the angle in a continuous motion. With the monitor closed, press the BAND button to change the AM or FM band. 5. AUDIO/LO/DX Rotate to adjust the volume. Press and release to enter and/ or confirm audio settings. Press and hold to activate the Local (LOC) setting. 6. SRC Press to select playing mode. Long press switch the unit ON/OFF. 7. LCD Display 8. MUTE Press to silence the receiver. Press again to resume previous volume level. NOTE: The UV 8 features Softmute, which will allow the volume to increase or decrease gradually when the MUTE function is activated or deactivated.
9. IR Remote Control Receiver 10. ( ) DVD Mode: Press once to play back the previous chapter / track. TUNER Mode: Press once to auto-search for the previous available radio station. MENU Mode: Press once to move the cursor to the left. 11. ( ) DVD/Disc Mode: Press once for slow forward/slow reverse. TUNER Mode: Press to go down one frequency step. MENU Mode: Press once to move the cursor down. 12. RESET Press to reset system settings to factory default (except the password and parental lock setting). 13.Pause/Play/Enter Press to pause or resume playback or to confirm current selection. 14. ( ) DVD/Disc Mode: Press once to enter the next chapter or track. TUNER Mode: Press once to auto-search the next available radio station. MENU Mode: Press once to move the cursor to the right. 15. ( ) DVD/Disc Mode: Press once for fast forward/fast reverse. TUNER Mode: Press to go up one frequency step. MENU Mode: Press once to move the cursor up. 16. ( ) Press once for disc insertion/ejection.Press and hold to reset core mechanism position. 17. TFT Display

REMOTE CONTROL

NOTE: Your remote control may differ slightly from the one pictured here. The above diagram is for illustrative purposes only.
USING THE TFT MONITOR Open/Close TFT Monitor Open TFT Monitor Press the OPEN button (1) on the front panel or press the ( ) button (25) on the remote control to activate the mechanism that moves the display panel into the viewing position. Close TFT Monitor Press the OPEN button (1) on the front panel or press the ( panel back into the compartment.
) button (25) on the remote control to load the display
TFT Monitor Auto Open If TFT Auto Open is on when the unit is turned on, the monitor automatically moves to the viewing position. If TFT Auto Open is off when the unit is turned on, press the OPEN button (1) or ( ) button (25) on the remote control to move the monitor into the viewing position. If TFT Auto Open is set to Manual, the TFT will not close when the key is turned off. Monitor Tilt Angle Adjustment A known characteristic of LCD panels is the quality of the display in relationship to the viewing angle. The monitor angle can be adjusted for optimum viewing using one of the following methods: Press the Tilt buttom to activate the Tilt function (a yellow symbol appear at the right top corner of the screen). Step by Step Angle Adjustment Press the ^ or button on the remote control to adjust the tilt angle of the screen one step at a time. ^ Press the TILT button (4) on the control panel. While the yellow angle icon is displayed near the top right corner of the screen, use the /\ or V buttons (11, 15) on the joystick to adjust the tilt angle of the screen one step at a time. Continuous Angle Adjustment Press and hold the ^ or button on the remote control to adjust the tilt angle in a continuous motion. ^ Press the TILT button (4) on the control panel. While the yellow angle icon is displayed near the top right corner of the screen, press and hold the /\ or V buttons (11, 15) on the joystick to adjust the tilt angle in a continuous motion.

^ ^ ^ ^

Aspect Ratio Press the DISP button (10) on the remote control or the WIDE button (2) on the monitor to adjust the aspect ratio as follows: FULL The entire screen is extended horizontally to the aspect ratio of 16 to 9. The extension ratio is the same at any point. NORMAL The conventional display image has a 4 to 3 ratio of horizontal to vertical, leaving a blank area on the right and left sides of the display.

Image Setting Table 2 shows the video output mode for each playing source.
Parameter Adjustment Procedure 1. Enter Picture Quality Setting Mode: Press the PIC button (24) on the remote control or the PIC/AS/PS button (3) on the monitor. 2. Select Item to Set: Press the AUDIO button (5) on the control panel to select BRIGHT or CONTRAST. 3. Set Parameters: Press the +/ buttons (15, 16) on the remote or turn the rotary encoder (5) on the control panel. 4. Exit Picture Quality Setting Mode: Press the PIC button (24) on the remote control or the PICTURE/AS/PS button (3) on the monitor Parking Brake Inhibit When the PRK SW cable is connected to the brake switch, the display on the TFT monitor will display video only when the vehicle brake is applied. Parking brake function is overridden when the video source is set to CAMERA. When the parking brake inhibit is active, the front monitor displays Parking Is On, preventing the driver from watching content while driving. Rear video screens are not affected. Monitor Movement Mechanism If an obstruction occurs in the monitor path, the following protective measurements can be executed to prevent damage to the mechanism or monitor:
After the protective procedure is executed, normal operation is resumed by pressing the OPEN button (1) or disconnecting and reconnecting the power.
OPERATING INSTRUCTIONS Power On / Off Press the /SRC button (6) on the unit (or the / POWER button (4) on the remote control) to turn the unit on. The buttons on the front of the unit light up and the current mode status appears in the LCD (7). You can also turn on the unit by pressing the OPEN button (1) and opening the TFT screen. Press and hold the button to power off the unit.The monitor is drawn back into the main compartment.
Audible Beep Confirmation An audible beep tone confirms each function selection. The Beep tone can be disabled through the Setup menu. Mute Press the MUTE button on the front panel (8) or remote control (3) to mute the volume from the unit. Press the MUTE button again to restore the volume. MUTE is displayed on the LCD. Adjusting the volume or using any of the audio setup features cancels the mute function. Playing Source Selection Press the SRC button (6) on the front panel or the SRC button (8) on the remote to change between available playing sources in the following order: AM/FM/RDS, DISC, AUX 1, AUX 2 and CAMERA. The playing mode is displayed on the TFT and LCD screens. Source Menu You can also use the touch screen to change the source through the SOURCE MENU. To access the SOURCE MENU, touch the top left corner of the screen.

Hardware Sub-menu Features If the rear-view video camera is connected, the unit is on, and the TFT monitor is retracted inside the unit, the TFT monitor automatically moves into the viewing position and Camera mode is selected upon shifting into REVERSE gear. When shifting into DRIVE gear, the TFT monitor is retracted back inside unit.
If the monitor is in display mode, the monitor automatically switches to CAMERA mode upon reverse driving. When the reverse driving stops, the monitor return to its original input mode. P.VOL Sub-menu Features
TS Cal (Screen Calibration) To access the Screen Calibration function from the SETUP menu, select the TS CAL option. After entering calibration mode, a crosshair appears in a corner quadrant of the screen. To begin calibration, press and hold the crosshair for one second until it moves to the next quadrant. Continue for each quadrant until the calibration is completed. Exiting the System Setup Menu To exit setup mode and resume normal playback, press the SETUP button (31) on the remote control or touch the BACK button on the screen.
TUNER OPERATION Tuner TFT Display

1. 2. 3. 4. 5. 6.

Touch to view the SOURCE MENU and select a new playback source Current radio band indicator Current present station indicator Radio frequency indicator or PS information Clock Radio function indicators ST: Stereo broadcasting indicator LOC: Strong local signal broadcasting indicator TA: Traffic Announcment indicator TP: Traffic Program indicator AF: Alternative Frequency indicator PTY: Program Type indicator 7. Setup. Touch to open setup menu 8. Numeric keypad 9. Information display bar for radio text 10. Preset radio stations 11. Touch to seek backward 12. Touch to tune backward step by step 13. Touch to seek forward 14. Touch to tune forward Stepp by Stepp 15. AS: Touch to Auto Store stations 16. BAND: Touch to change radio bands 17. 1/2 or 2/2: Touch to view a second page of on-screen buttons 18. MEM: Store current station into present memory 19. AF: Touch to activate / deactivate AF function 20. TA: Touch to activate / deactivate TA function 21. PTY: Program Type indicator (No touch button) 22. PS (Preview Scan): Touch to scan all available, stopping for 5 seconds at each and continuing until one station is selected 23. LOC: Touch to tune to strong local stations
Switch to Radio Tuner source Touch the top left corner of the screen (the RADIO circle) to view the SOURCE MENU. Touch Radio. Press the SRC button (6) on the front panel or remote control (8) to switch to the AM/FM or RADIO source. Select FM/AM Band Touch the BAND button (16) on the screen, or press the BAND button on the unit (4) or remote control (20) to change between the following bands: FM1, FM2, FM3, AM1, and AM2 NOTE: The BAND button on the unit only works when the TFT is closed. Seek Tuning To seek the next higher station: Touch the >>| button on screen. Press the >>| button (19) on remote control. Press the > button on the joystick (14). To seek the next lower station: Touch the |<<| button on screen. Press the |<< button (17) on the remote control. Press the < button on the joystick (10). Manual Tuning To increase or decrease the tuning frequency one step: Touch the or v buttons on screen. v Press the >> or << buttons (14, 22)on the remote control. Press the /\ or V buttons (11, 15) on the joystick.

Direct Tuning To enter a radio station directly, touch the

button.

Enter the desired radio station using the on-screen numberpad. Press the enter button (arrow) to tune to the selected station. To exit the screen without changing the station, touch Exit. To clear your entry and start over, touch Clear. Using Preset Stations Six numbered preset buttons store and recall stations for each band. All six stored stations (P1-P6) for the current band appear on the screen. Storing a Station 1. Select a band (if needed), then select a station. 2. Touch the on-screen MEM button (18) to open the preset screen. 3. Touch the preset number in which you would like to store the current station (or press EXIT to cancel and close the menu). The preset number and station appears highlighted.
Recalling and Storing broadcaster using the presets and the Automatic Storing ( AS) Function:
Recalling a Station 1. Select a band (if needed) 2. Touch an on-screen button (P1- P6) to select the corresponding stored station. Manual Storing of a Station 1. Please manual tune to the desired broadcaster (Frequency) 2. Push the MEM on-screen button and then select the desired preset (P1- P6) 3. The broadcaster will be stored at the selected one 4. Instead of the frequency the Program Service ID (i.e. BBC) will be stored Automatic Storing (AS) of the strongest Stations 1. Push the Automatic Storing (AS) on-screen button for 2 seconds 2. The VME start scanning the available broadcasters (which take a while) 3. Once scanning is finished the 6 strongest ones will be stored at P1- P6 4. During Automatic Storing (AS) only the frequencys will be stored at P1- P6 to decrease the scanning/ storing time 5. If you now manually select P1- P6, then the PS information will be finally stored for the selected preset (i.e. P2: BBC) Radio Text message bar 1. The Radio Text (RT) information is a part of the RDS signal which is supplied by the broadcaster. This information will be shown at the lower bar (i.e. ABCD) 2. Not all broadcaster support this additional information or all the time Preview Scan (PS) To scan the AM or FM band for a preview of available stations in your particular area, touch the 1/2 button to access the second screen of menu options touch the PS button (21). Touch again to stop preview scan.
Local Radio Station Seeking (LOC) When the Local function is on, only radio stations with a strong local radio signal are played. To activate the Local function in AM/FM tuner mode, touch the 1/2 button to access the second screen of menu options, and then touch the onscreen LOC button. Touch the LOC button again to turn Local off. When the Local function is active, the LOC indicator at the top of the screen is illuminated.

DVD/VCD VIDEO OPERATION NOTE: When properly installed, DVD video cannot be displayed on the main TFT screen unless the parking brake is applied. If you attempt to play a DVD while the vehicle is moving, the TFT screen displays PARKING with a blue background. Rear video screens, if applicable, will operate normally. Opening/Closing the TFT Video Screen Opening the TFT Screen To open the TFT video screen, press the OPEN button (1). The unit beeps and then opens. Closing the TFT Screen Press the OPEN button (1) again to close the TFT screen. If the screen is in the IN position, it moves out before closing. Insert/Eject Disc Upon inserting a DVD disc, DVD mode is entered and disc play begins. NOTE: If Parental Lock (Rating) is activated and the disc inserted is not authorized, the 4-digit code must be entered and/or the disc must be authorized (see General Sub-menu Features on page 64 ). You cannot insert a disc if there is already a disc in the unit or if the power is off. NOTE: DVD-R and DVD-RW will not play unless the recording session is finalized and the DVD is closed. Ejecting a Disc Press the button (16) on the unit or remote control (35) to eject the disc. The unit automatically reverts to Tuner mode. You may eject a disc with the unit powered off. The unit will remain off after the disc is ejected. Reset the Loading Mechanism If the disc loads abnormally or an abnormal core mechanism operation occurs, press and hold the the unit or remote control (35) to reset the loading mechanism. Normal operation resumes.

button (16) on

Accessing DVD Mode To switch to DVD mode when a disc is already inserted, press the SRC button (6) on the front panel or remote control (8) until DISC appears at the bottom of the screen. Controlling Playback To access the on-screen controls, touch the screen. Touch the 1/2 button to view a second page of controls.
Stopping Playback Touch the stop button ( ) on the screen or press the / BAND button (20) on the remote control to stop DVD play. Pausing Playback Touch the pause button (||) on the screen (or press the >/|| button on the remote control) to suspend disc playback. Press the > button on the screen to resume disc playback. Slow Motion Playback Press the << button (22) on the remote control, the V button (11) on the joystick, or the << button on the screen to play the current title in slow motion. Keep pressing and releasing the button to increase the rate from 2X to 4X, 8X, and 20X. Press >/|| (18) on the remote control or touch the onscreen play button (>) to resume normal play. Fast Forward Playback Press the >> button (14) on the remote control, the /\ button (15) on the joystick, or the >> button on the screen to fast forward. Keep pressing and releasing the button to increase the rate from 2X to 4X, 8X, and 20X. Press >/|| (18) on the remote control or touch the onscreen play button (>) to resume normal play. Repeat Playback Press the REPT button (7) on the remote control or the following: DVD: Repeat Chapter, Repeat TItle, Repeat Off VCD (PBC Off): Repeat Single, Repeat Off

DVD Playback Information The following information is displayed at the top of the screen during DVD playback:
Title: 05/08 05/08" indicates the fifth of 8 titles on the DVD is currently playing. C : 2// 16" indicates that the second of 16 titles on the DVD is currently playing. 00:41:28 00:41:28 indicates the playback time of the current title. 2 / 6 Eng The language display information indicates the second language out of 6 (English) is currently being used. VCD Playback Information
The following information is displayed at the top of the screen during VCD playback:
VCD2.0 Format of current disc. T: 6/18 6/18 indicates the sixth of 18 tracks on the VCD is currently playing. 00:02:18 00:02:18 indicates the playback time of the current track.
Regional Coding:Both the DVD-Player and discs are coded by region. These region codes must match in order for the disc to play. If the codes do not match, the disc wont play. This units code is 2. DVDs with other region codes
DVD/CD AUDIO OPERATION Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The UV 8 will play music or other audio files from the following disc media: CD-DA CD-R/RW DVD DVD+R/RW DVD-R/RW Upon inserting a disc with the TFT screen open, the disc and track title (if available), along with the track number and playing time appear on the screen. CD Player User Interface The on-screen indicators and touch key areas for CD playback are outlined below.
1. Current track and total number of tracks on disc 2. Elapsed playing time 3. Clock time 4. Track titles 5. Disc title 6. Touch to play/pause disc playback 7. Touch to stop disc playback 8. >>|: Touch to move to next track 9. |<<: Touch to move to previous track 10. >>: Touch to fast forward current track 11. <<: Touch to rewind current track 12. Touch to activate/deactivate Repeat play mode 13. Touch to activate/deactivate Random mode 14. Touch to access the direct entry screen 15. : Touch to view the SETUP menu 16. Touch for quick access to Equalizer level settings 17. Touch to view the SOURCE MENU and select a new playback source
Controlling Playback Stopping Playback Touch the button on screen or press the /BAND button (20) on the remote control to stop disc play. To resume playback, touch the button on screen, press the joystick button (13) on the front panel, or press the >/|| button on the remote control (18). Pausing Playback Touch the button on screen or press the joystick button to suspend or resume disc playback. Moving Through Tracks Press the >>| button (19) on the remote control or on screen or use the > button on the joystick (14) to advance to the next track on the disc. Press the |<< button (17) on the remote control or on screen or use the < button on the joystick (10) to move to the previous track. Repeat Playback Touch the button on screen, press the RPT button on the remote control (7) to alter repeat mode according to the following: DVD: Repeat Chapter, Repeat Title, Repeat Off CD-DA: Repeat One, Repeat All, Repeat Off CD-R/RW: Repeat One, Repeat All, Repeat Off DVD-R/RW: Repeat One, Repeat All, Repeat Off

The UV 8 player will only recognize three folder levels and does not display folders containing only other folders. In the example above, the unit will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain any tracks directly. Folder 5 is not recognized at all since it is at the fourth level.
MP3 User Interface The on-screen indicators and touch key areas for MP3 playback are outlined below.
1. Current track and total number of tracks on root of disc 2. Elapsed playing time, track length 3. Clock time 4. Track titles 5. ID3 information 6. II : Touch to play/pause disc playback 7. : Touch to stop disc playback 8. >>|: Touch to move to next track 9. |<<: Touch to move to previous track 10. / >>: Touch to navigate playlist/touch to fast forward 11. /<<: Touch to navigate playlist/touch to fast rewind or reverse 12. DIR -: Touch to view the previous folder 13. DIR +: Touch to view the next folder 14. Touch to access the direct entry screen 15. Touch to view the SETUP menu 16. Touch for quick access to Equalizer level settings 17. Touch to view the SOURCE MENU and select a new playback source 18. Folder name
Controlling Playback Playing MP3/WMA Files After inserting a MP3/WMA disc, files will play in the sequence of the Root directory. NOTE: When burning MP3 / WMA files onto a DVD disc, use the 2X or 4X burning option, if available. This slower burning speed will help eliminate buffer errors and increase disc reading reliability. Also, use folders when burning large numbers of songs / files to a disc for easy music navigation. Select the "Disc at Once" option and close your disc. Stopping Playback Touch the button on screen or press the / BAND button (20) on the remote control to stop disc playback. button on screen, press the joystick button (13) on the front panel, or press the >/|| To resume playback, touch the button (18) on the remote control.
Pausing Playback Touch the button on screen, press the joystick button (13) on the front panel, or press the >/|| button (18) on the remote control to suspend or resume disc playback. Touch the button on screen, press the RPT button (7) on the remote control to alter repeat mode according to the following: Repeat Single, Folder Repeat, Repeat Off. Use the numeric keypad (29) on the remote control to access files directly or press the button (see Direct Track Entry on page 79).

Moving Through Tracks Press the >>| button (19) on the remote control or on screen or use the > button on the joystick (14) to advance to the next track on the disc. Press the |<< button (17) on the remote control or on screen or use the < button on the joystick (10) to move to the previous track. Repeat Playback Press the REPT button (7) on the remote control to alter repeate mode according to the following : Repeat Single, Folder Repeat, Repaet Off
Random Play Select Press the RDM button (33) on the remote control to play the files on the disc in a random, shuffled order. Press RDM again to cancel Random Play mode. NOTE: CD-R and CD-RW will not play unless the recording session is finalized.
Direct Track Entry Use the numeric keypad (29) on the remote control to access files directly or press the button

TROUBLESCHOOTING

GENERAL Unit will not power on Radio Fuse blown Car battery fuse blown Illegal operation Install new fuse with correct rating Install new fuse with correct rating Press the RESET button located in the bottom right corner of the front panel Replace battery with new one Remove battery and install correctly Check wiring and correct Increase volume level Review wiring diagram and check MUTE connection Replace speakers Adjust the channel balance to the center position Insulate all speaker wiring connections Use original copy Connect proper speakers Check speaker contact Check that the MUTE connection is not grounded and that its properly insulated Check wiring and correct

Corrective Action

Remote control does not function
Battery depleted Battery installed incorrectly Improper audio output connection Volume set too low Improper MUTE connection Speakers damaged Heavily biased volume balance Speaker wiring is in contact with metal part of car

No/low audio output

Poor sound quality or distortion
Pirated disc is in use Speaker power rating not compatible with unit Speaker is shorted MUTE wire is grounded Incorrect connection between ACC and positive battery wire
Tel-Mute malfunction Unit resets itself when engine is off
TFT MONITOR Monitor does not open automatically No image
TFT Auto Open is turned off Incorrect connection to parking brake wire PRK SW is activated, parking brake is not engaged
Turn TFT Auto Open on Check wiring and correct Stop vehicle in safe place and apply parking brake

Flashing image or interference appears on screen
DVD is not compatible with current TV system settingsChange setup to accommodate disc Improper video signal connections Check wiring and correct
Prolonged image or improper height/width ratio display Monitor stops at incorrect position
Improper aspect ratio setup Moving path is blocked
Use correct aspect ratio setting Press OPEN key to restart monitor movement
TUNER Weak station searching Auto antenna is not fully extended Auto antenna not properly connected LOCAL function is activated Disc is warped or scratched Disc is dirty or wet Laser pickup is dirty Incompatible disc is used Disc rating exceeds Parental Lock rating limit Disc region code is not compatible with unit Disc is inserted upside down
Insert disc with label side up
Connect the auto antenna control cable properly Connect the auto antenna control cable properly Turn LOCAL function Disc does not play back Use disc in good condition Clean disc with soft cloth Clean laser pickup with cleaning disc Use compatible disc Change Parental Lock settings to lower restriction Use disc with proper region code
Image blurred, distorted, or dark PCB cannot be used during No repeat or searching MP3 Interruption occurred during playback
Disc is illegally copied VCD playback while playing VCD
Use original disc PCB is not available on the disc PCB is on Turn PCB off
Disc is dirty or scratched File is damaged/bad recording
Clean disc or replace Recreate disc with good files
Incorrect playback message displayed
Message is longer than LCD can display

Message Displayed

Loading No Disc
Disc is being read Disc is dirty Disc is upside down Disc not present in loading compartment Disc is dirty Disc is upside down Disc format is not compatible with this unit DVD is not compatible with region code of unit Illegal mechanism operation
Clean disc with soft cloth Insert disc with label side up Insert disc Clean disc with soft cloth Insert disc with label side up

Bad Disc

Unknown disc Region Error Error
Press EJECT key for 5 seconds to reset loading mechanism
Care and Maintenance 1. Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and nonneutral detergent (such as alcohol) may result in scratching or discoloration. 2. Do not get water or cleaning fluids on the unit. 3. If the temperature inside the player gets too hot, a protective circuit automatically stops play of the disc. If this occurs, allow the unit to cool before operating the player again. 4. Never insert anything other than a 5 (12 cm) compact disc into the player as the mechanism can be damaged by foreign objects. 5. Do not attempt to use a 3 (8 cm) CD-Single disc in this unit, either with or without an adaptor, as damage to the player and/or disc may occur. Such damage is not covered by the Warranty on this product. 6. The CD player may not operate properly in extreme hot or cold. If such conditions occur, allow the interior of the vehicle to reach a normal temperature before using player. 7. When the vehicle warms up during cold weather or under damp conditions, condensation may appear on the LCD panel. Should this occur, the screen will not operate properly until the moisture has evaporated. 8. We suggest you use a cleaning disc in this unit more frequently than in the unit in your home due to the environmental conditions of the vehicle.

GARANTIEKARTE WARRANTY CARD

Typ/ Type

Serien-Nr./Serial-No.
Name und Anschrift des Hndlers /Stempel Name and address of the dealer/stamp

Kufer/Customer

Name/Name Strae/Street PLZ, Ort /City Land /Country

Kaufdatum / buying date

Nur gltig in Verbindung mit Ihrer Kaufquittung! No warranty without receipt!
Audiovox Audio Produkte GmbH Lise-Meitner-Str. 9 D-50259 Pulheim Germany Tel. ++49 (0) 2234 807-0 Fax++49 (0) 2234 807-399 www.audiovox-germany.de