Owner's Manual

VBPEX5

5" LCD MONITOR

Important Notice

It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the drivers seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, the VBPEX5 should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle.

Warnings

Do not use any solvents or cleaning materials when cleaning the video Monitor. Do not use any abrasive cleaners, they may scratch the screen. Use only a lightly dampened lint free cloth to wipe the screen if it is dirty. Before putting on headphones always adjust the volume setting to the lowest position. Do not put pressure on the screen. Caution children to avoid touching or scratching the screen, as it may become dirty or damaged.
A. Introduction Thank you for selecting the VBPEX5, 5 inch Liquid Crystal Display (LCD ) Monitor. The VBPEX5 can be connected to the VBP3000 and VBP4000, (Please contact Audiovox's retailers). The connection of the Monitor is plug and play. The Monitor utilizes the latest state of the art electronics and is designed for use in vehicles, hotels, offices or your home and is constructed to provide years of reliable, trouble-free service. Please read the entire manual prior to operation. This documentation will assist you in installing the system properly to obtain the best equipment performance. B. Cautions 1. Use only the approved power cable (AC/DC Adapter or DIN cable) supplied with this Monitor. When the system is left unattended and unused for long periods of time, unplug it from the power source. Always disconnect the power source first and then the jack from the system. 2. Ensure that the Monitor is installed in accordance with the instructions and illustrations provided in this manual. Do not use the system in the front seat while operating your vehicle. 3. To prevent fire or electric shock, do not expose this appliance to rain, moisture or long periods of direct sunlight. Keep the unit away from sources of heat. Do not operate or store the unit close to strong magnetic fields. Do not spill or spray liquid of any kind on or in the system (this may result in a fire or electric shock). 4. To ensure proper ventilation, never cover or block the slots and openings with a cloth or other material. 5. To reduce the risk of electric shock, do not remove the back cover of the unit. There are no user-serviceable parts inside. Contact qualified service personnel if your system is in need of repair. 6. When cleaning, make sure the system is unplugged from power source. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the system only. C. Contents ITEM 1. 2. 3. 4. 5. 5" LCD Monitor VPBEX5 DIN Cable AC to DC Power Adapter Cigarette Lighter Adapter Pouch PART NUMBER 136C2124 112-3092 136-1830 136-1831 126-1170
QUANTITY One One One One One
D. Positioning the Monitor Option 1 Vehicle Headrest (Refer to Figure 1)
INSTALL AT ION INSTRUC T IONS INSTALLAT ION INSTRUCT IONS INSTALL AT ION INSTRUCT IONS INSTALL AT ION INSTRUC T IONS INSTALL AT ION INSTRUC T IONS
Figure 1 Loop the strap of the pouch around the headrest in the vehicle, and pull the end of the strap while holding the buckle until the pouch is tightly secured. Option 2 Flat Surface (Refer to Figure 2)

Figure 2 Rotate the base of Monitor backward and place it on a flat surface. Adjust the screen for a proper viewing angle. This can be done with the Monitor inside or outside the pouch.
E. Controls/Indicators/Connectors (Refer to Figure 3)
Figure 3 1. Headphone Jack 2. 12V DC Input Jack 3. Remote Control Sensor: The sensor will relay commands to the either the VPB3000 or VBP4000. 4. Power LED Indicator 5. Power Switch 6. TV/VCP (Video Cassette Player) Select Switch 7. Brightness Up/Down Control 8. Volume Up/Down Control 9. Right Audio Input Jack 10. Left Audio Input Jack 11. Video Input Jack 12. Monitor Port (Input)
F. Powering the Unit NOTE: When the VBPEX5 is connected to either a VBP3000 or VBP4000 using the supplied DIN cable, there is no need for a power source to be connected to the DC 12V IN jack. Option 1 Indoor Power (Refer to Figure 4)
Figure 4 c Using the AC/DC adapter supplied with the VBPEX5, plug the connector end into the DC 12V IN jack on the side of the Monitor. Plug the AC/DC adapter into a 120 VAC power receptacle. This can be done with the Monitor inside or outside the pouch. Option 2 Vehicle Power (Refer to Figure 5)
Figure 5 Using the cigarette lighter adapter supplied, plug the connector end into the DC 12V IN jack on the side of the Monitor. Plug the cigarette lighter adapter into the cigarette lighter socket. This can be done with the Monitor inside or outside the pouch.
G. Connecting to the VBP3000/VBP4000 Option 1 Using Two Monitors (Refer to Figure 6 and 7)

VBP3000

DIN CABLE

Figure 6

VBP4000

VBPEX5 VBPEX5

Figure 7 Using the DIN cable supplied with the VBPEX5, connect one end of the DIN cable to the Monitor Port (Input) located on the side of the Monitor. Connect the other end of the DIN cable to the either of the Monitor Ports (Output) on the rear of the VBP3000 or the side of the VBP4000. When the VBP3000/VBP4000 is operational, audio/video
signals, power (12 Volt DC ) and Infrared control signals are routed through the DIN cable to the Monitor. Since the Monitor is deriving power from the VBP3000/ VBP4000, there is no need for a power source to be connected to DC 12V IN jack located on the Monitor. NOTE: If connecting the Monitor to the VBP4000 be certain to slide the TV/VCP select switch located on the face of the Monitor to the VCP position. H. Using External Audio/Video Sources (Refer to Figure 8) Connect the VBPEX5 to an external power source. Refer to Figure 4 and Figure 5. Plug the external source audio/video signals into the appropriate jacks on the side of the Monitor. Plug the video output from an auxiliary source such as Camcorder, Video Game, DVD Player, Video Cassette Player etc. into the yellow Video In jack. Plug the left audio signal into the white jack. Plug the right audio signal into the red jack.

Figure 8 I. Using Headphones (Refer to Figure 8) Optional wired headphones may be used with the Monitor. Simply plug in the headset to the headphone jack on the side of the Monitor and both internal speakers will be turned off. J. Operation (Refer to Figure 3)
1.Slide the POWER ON/OFF switch to the on position to turn the Monitor on. The POWER LED will light. 2.When connecting the VBPEX5 Monitor to the VBP3000, slide the TV/ VCP switch to the appropriate position for selecting the TV or VCP mode.
3. When connecting the VBPEX5 Monitor to the VBP4000, slide the TV/ VCP switch to the VCP position. 4. When connecting an external signal source to the VIDEO IN, AUDIO L IN, AUDIO R IN jacks on the VBPEX5, the TV/VCP switch can be set to either the TV or VCP position. 5. Use the BRIGHTNESS UP/DOWN control to adjust the picture to desired setting. 6. Use the VOLUME UP/DOWN control to decrease or increase volume level.
K. Specifications: Color System:... Screen Size:.. Power Supply:... Power Consumption:... Operating Temperature:.. Operating Humidity:... Storage Temperature:.. Dimensions (W x D x H).. Weight....
NTSC 5 Inches DC 12 V 6W 41~104 F (5~40)C 10-75% 4~140 F (-20~60)C 9.4" x 1.5" x 6.6" 1.6 lbs
OPERA INSTRUCT OPER AT ING INSTRUCT IONS

90 DAY LIMITED WARRANTY

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below. This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

U.S.A.: AUDIOVOX ELECTRONICS CORP., 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 ! 1-800-645-4994 CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA

Form No. 128-5047A

Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788

128-6325

WWW.audiovox.com
Product Information, Photos, FAQs Owners Manuals
For Customer Service Visit Our Website At
2002 Audiovox Electronics Corp., Hauppauge, NY 11788

VBP3000

VIDEO IN A BAG SYSTEM WITH DETACHABLE 5" LCD TV/MONITOR AND VIDEO CASSETTE PLAYER

A. Introduction

Thank you for selecting this Video in a Bag System. The system's main features include two 5" Liquid Crystal Display (LCD) TV/Monitors and Video Cassette Player (VCP) (see page 4 for a detailed feature list). The system utilizes the latest state of the art electronics and is designed for use in vehicles, hotels, offices or your home. The Video in a Bag System is constructed to provide years of reliable, trouble-free service. The system is compact so that you can take it with you anywhere and is designed for quick and easy installation. The system comes with two detachable displays that can be utilized and stored separately from the main unit. An additional monitor can be purchased and added to the system setup allowing you to utilize three monitors at once (two external and one attached). The connection of the additional is plug & play. Please read the entire instruction manual supplied with this product prior to operation. The documentation will assist you in installing the system properly to obtain the best equipment performance. All manuals should be stored for later use.

B. Precautions

1. The Video in a Bag System MUST be powered from switched Accessory power (i.e. not directly from the car battery). Power should be applied to the unit when the ignition key is in the Run and/or Accessory positions. NOTE: To prevent battery discharge, disconnect the Video in a Bag System jack from the cigarette lighter socket when the unit is not in use. 2. IMPORTANT!: There are two short Velcro straps located inside the bag. These straps are used to anchor the system securely inside the bag using the loop brackets on either side of the system. This will prevent the system from falling out and being damaged in transport or while in use in your vehicle. 3. Ensure that the LCD TV/Monitor, VCP and the Bag are installed in accordance with the instructions and illustrations provided in this manual. 4. The S hooks and all straps must be fastened correctly to secure the system in the vehicle in the event of an accident. 5. Operate the Video in a Bag System with the Bag open to ensure proper ventilation of the monitor and the VCP. 6. The system intended to be mounted for rear seat viewing only. DO NOT USE THE SYSTEM IN THE FRONT SEAT WHILE OPERATING YOUR VEHICLE.

C. Cautions and Warnings

1. Cleaning Video Head To prevent video head clogging, use only good quality VHS tapes and discard worn out tapes. If the heads become dirty over a period of time during normal operation of the VCP, the picture will be snowy and the auto-tracking will not adjust the picture correctly. We recommend using cleaning cartridges sparingly to restore normal picture. 2. Placement To prevent fire or electric shock, do not expose this appliance to rain, moisture or long periods of direct sunlight. Keep the unit away from radiators or other sources of heat. Do not operate or store the unit close to strong magnetic fields. Do not place the set on an unstable cart, stand, tripod, bracket or table to prevent it from falling. 3. Ventilation To ensure proper ventilation, never cover or block the slots and openings with a cloth or other material. 4. Object and Liquid Entry Do not push objects of any kind into the system through openings; do not spill or spray liquid of any kind on or in the system (this may result in a fire or electric shock). Do not place anything heavy on the unit. 5. Disassemble To reduce the risk of electric shock, do not remove the cover (or back). No userserviceable parts inside. Contact qualified service personnel if your system is in need of repair. 6. Cleaning Unit When cleaning, make sure the system is unplugged from power source. Do not use liquid cleaners or aerosol cleaners. Use a cloth lightly dampened with water for cleaning the exterior of the system only. 7. Power This system should be operated only from the type of power source indicated on the marking label. Use only the supplied power cable matching this set to avoid electric hazards. When the system is left unattended and unused for long periods of time, unplug it from the power source. Always disconnect the power source first and then the jack from the system. 8. Cassette Do not force a cassette into the compartment when the power cord is unplugged. An inverted cassette cannot be inserted. After playing a videocassette, remove it from the player. Store videocassettes in the sleeves or cases and in upright position.

INSTALL AT ION INSTRUC T IONS INSTALLAT ION INSTRUC T IONS INSTALL AT ION INSTRUCT IONS INSTALL AT ION INSTRUC T IONS INSTALL AT ION INSTRUC T IONS

D. Feature List

1.) One Video Cassette Player with Built In VHF/UHF/CATV Tuner system 2.) Two 5" LCD Monitors with AUX Inputs 3.) One Infra Red Remote Control 4.) One Bag (for carrying the unit and accessories) 5.) One Set of Straps for Mounting 6.) Two Pouches (for the detachable monitors) 7.) One DC Power Adaptor (cigarette lighter adapter) 8.) One AC to DC Power Adapter (two piece set) 9.) Two DIN Cable 10.) One Dipole Antenna 11.) One Slip-on COAX Connector 12.) Two Headphone Jacks
Figure 1 E. Powering the Unit
1. Refer to Figure 1. Unzip the lower compartment of the bag and take out the AC/ DC adapter. Plug one end of the AC to DC adapter into 110 VAC power receptacle and the other end into the DC IN 12V jack on the rear of the system.
2. Refer to Figure 2. For use in a vehicle, take the cigarette lighter socket adapter from the lower compartment, plug one end into the DC IN 12V jack on the rear of the unit, slide the cord through the slot in the bag, and plug the other end into the cigarette lighter socket.
Figure 2 F. Powering the Detached Monitor or the Additional Monitor
1. The attached monitor can be detached from the system by depressing the button below the screen with one hand and removing the monitor with the other (Refer to Figure 13 Item #13.). You may take the additional monitor from the bag. Take the AC/DC adapter from the lower compartment, plug one end into the DC IN 12V jack on the left side of the monitor, and the other end into the power receptacle indoors.

Figure 3

2.Refer to Figure 4. For use in a vehicle, take the cigarette lighter adapter from the lower compartment, plug one end into the DC IN 12V jack on the left side of the monitor and the other end into the cigarette lighter socket.

Figure 4

Note: 1). When the monitor is connected to the main unit the unit will supply inside power to the monitor, there is no need for another power source to be connected to the DC 12V IN jack on the side of the monitor. 2). Refer to Figure 5 and 6. When the monitor is separated (either the monitor detached from the main unit or the additional monitor), You can connect the MONITOR PORT on the side of the monitor to the MONITOR PORT on the rear of the main unit with the supplied DIN cable. If in the vehicle, insert one end of the DIN cable into the MONITOR PORT on the side of the detached monitor, slide the cable through the slot in the bag and insert the other end into the MONITOR PORT on rear of the main unit. After plugging in the main unit, DC 12V power, Audio/Video and IR signals will all be supplied through DIN cable to the separated monitor.

Figure 5

Figure 6
H. Installing the Unit with Bag Between the Driver/Passenger Seat Option 1 (Refer to Figure 7)

Figure 7

1. Take one of the supplied straps and connect the latch to the upper metal ring on the left side of the bag. Attach the "S" hook to the same ring after looping the strap around the headrest of the driver's seat. Repeat this process for the right side (Passenger Seat). 2. Take another strap and connect the latch to lower metal ring on the left side of the Bag. Attach the "S" hook to the same ring after looping the strap around the driver's seat rail. Repeat this process for the right side. In some vehicles, it may be necessary to attach the "S" connector to the rail directly, as it may not be long enough to reach back to the ring. Also, depending on the desired angle, you may need to attach the latch to either the front or the rear ring on the bottom of the Bag, depending on your vehicle. 3. Adjust the straps tightlyso that the bag is secured. 4. Unzip the bag on both the left and right side. The system will lean against the front of the bag at about a 15-degree angle when the zippers are fully unzipped. Adjust the zippers so that the unit is at the proper angle to allow the screen to be adjusted for the best viewing angle.
Option 2 (Refer to Figure 8)
Figure 8 1. Follow the installation instructions shown in the Option 1. 2. Remove the second monitor and its pouch from the front compartment of the bag. 3. Unfastening the Velcro strap and remove the monitor from the pouch. 4. Rotate the base of the second monitor backward so that it may be placed in an upright position on a flat surface. 5. Insert one end of the DIN cable into the MONITOR PORT on the side of the detached monitor, slide the cable through the slot in the bag, and insert the other end into the MONITOR PORT on rear of the main unit.
Option 3 (Refer to Figure 9)

Figure 9

1. Follow the installation instructions shown in the Option 1. 2. Remove the additional monitor and pouch from the front compartment of the bag, make sure to feed the bottom piece of the pouch into the long slot of the Monitor and attach the Velcro strap to fasten the monitor in the pouch. Then loop the strap of the pouch around the headrest and pull the end of the strap while holding the buckle until the pouch is tightly secured. 3. Insert one end of the DIN cable into the MONITOR PORT on the left right side of the detached monitor, slide the cable through the slot in the bag and insert the other end into the MONITOR PORT on rear of the main unit.

I. Installing the Unit with Bag on the Back Seat in a Car
There is no need to remove the four straps from the bag as they are not used in this installation.
Option 1 (Refer to Figure 10).

Figure 10

Carefully place the system (back facing up) on the back seat. Guide the vehicles safety belt through the short strap sewn on the front of the bag. Then secure and adjust the safety belt so that the unit is not free to move around. Finally uncover the attached monitor and adjust the screen for a desired viewing angle.
Option 2 (Refer to Figure 11)

Figure 11

1. Follow the installation instruction shown in the Option 1. 2. Detach the monitor from the system by depressing the button below the screen with one hand and removing the monitor with the other. Slide the monitor into the spare monitor pouch, feed the bottom piece of the pouch into the long slot of the monitor, and attach the Velcro strap to fasten the monitor in the pouch. Then loop the strap of the pouch around the headrest, and pull the end of the strap when holding the buckle until the pouch is tightly secured.
3. Remove the additional monitorand pouch from the front compartment of the bag, making sure to feed the bottom piece of the pouch into the long slot of the monitor and attach the Velcro strap to fasten the monitor in the pouch. Then loop the strap of the pouch around the headrest of the same row, and pull the end of the strap when holding the buckle until the pouch is tightly secured. 4. Insert one end of the DIN cable into the MONITOR PORT on the side of the detached monitor. Slide the cable through the slot in the bag and insert the other end into the MONITOR PORT on rear of the main unit. For an additional monitor, repeat this process using second of the two DIN cables supplied with the unit.
J. Using the System in a Hotel, Office or Home (Refer to Figure 12.)

Figure 12

1. Place the unit on a table or other level surface with the unit bottom facing down. Adjust the screen for a desired viewing angle. This can be done with or without the unit inside its bag. 2. Take the second monitor from the front compartment of the units bag. rotate the base of the monitor backward so that it may be placed on a table or other level surface. Adjust the screen for a proper viewing angle. This can be done with or without the monitor inside its bag of its pouch. 3. Insert one end of the DIN cable into the MONITOR PORT on the side of the detached monitor. Slide the cable through the slot in the bag and insert the other end into the MONITOR PORT on rear of the main unit.
K. Controls/Jacks/Plug/Indicator (Refer to Figure 13)

Figure 13

1. Headphone Input Jack 2. 12V DC Input Jack for Monitor 3. Remote Control Sensor 4. Power LED Indicator for Monitor 5. Power Switch for Monitor 6. TV/VCP Select Switch 7. Brightness Up/Down Thumbwheel 8. Volume Up/Down Thumbwheel 9. Audio R Input Jack 10. Audio L Input Jack 11. Video Input Jack 12. Monitor Port (Input) 13. Release Button for Monitor 14. Power Button for VCP 15. Stop/Eject Button 16. Auto Repeat Button 17. (Fast) Rewind Button 18. (Fast) Forward Button 19. Play Button 20. RF Input Jack 21. Dipole Antenna Connector 22. Reserve Hole for Antenna 23. 12V DC Input Jack 24. Monitor Port #1 (Output) 25. Monitor Port #2 (Output)

L. Remote Control (Refer to Figure 14)
1. TV Power Button 2. Number Buttons 3. Skip Search Button 4. TV/CATV Select Button 5. VCP Power Button 6. (Fast) Rewind Button 7. (Fast) Forward Button 8. TV Channel Up Button 9. TV Channel Down Button 10. Auto Memory Button 11. Erase/Write Button 12. Play Button 13. Stop/Eject Button 14. Pause Button
Figure 14 M. Watching a Movie
1. With power applied to the unit, select the VCP mode by sliding the TV/VCP switch on the face of the monitor to the TV/VCP position. Insert the videotape into the VCP, you will feel the automatic pull on the cassette as it is loaded and the VCP will go into the play mode automatically. 2. Press POWER on the VCP to turn it on or off. Slide the POWER switch on the face of the monitor to turn it on or off. 3. Press (FAST) FORWARD or REWIND button to scan forward or backward and press it again to increase the speed. 4. Press PAUSE on the Remote Control to make the image still. 5. Press PLAY to resume the normal playing mode. 6. Press STOP/EJECT to stop the playing, and press it again to eject the cassette. 7. Press AUTO REPEAT to activate the repeat playing. When the tape reaches the end, the VCP will automatically rewind the tape to the beginning and then repeat playing. In this mode, all other controls except the power key arent functional. Press it again to deactivate the repeat playing. 8. Adjust the volume control and the brightness control on the monitor for individual preference. Note: If the system is exposed to excessive levels of moisture it will display the word DEW on the screen when in VCP mode. If this occurs, the only VCP function available will be Eject until the moisture level in the system is sufficiently reduced. All other system functions will remain while the VCP functions are halted. The word DEW will disappear from the screen and all VCP functions will return when the moisture level is reduced.

N. Watching TV

1. Antenna a. Refer to Figure 15. Plug the dipole antenna into the reserve hole on the back of the system with its side that connects the cable facing up, you will hear a snap as it locks into place. Plug its connector into the RF IN jack. Extract the dipole antenna and adjust its extension, angulation and direction to optimize the picture and sound.

Figure 15

b. If there is poor reception of signals with the dipole antenna, connect an external antenna or the CATV to the antenna jack. 2. With power applied to the system, select the TV mode by sliding the TV/VCP switch on the face of the monitor to the TV position. 3. Press POWER on the VCP to turn on or off the TV. Push POWER on the face of the monitor to turn it on or off. 4. Press AUTO MEMORY on the remote control to automatically search and store the channels The unit will start to play the first channel automatically. 5. Press CHANNEL UP/DOWN or the number buttons to get to your desired TV channels. 6. Press SKIP SEARCH on the Remote Control until SKIP MODE ON is displayed on the screen, then if you press CHANNEL UP/DOWN, the TV will stop only on the active TV channels. Press SKIP SEARCH until SKIP MODE OFF is displayed on the screen. Then all the TV channels will be shown pressing CHANNEL UP/DOWN. 7. Press ERASE/WRITE until MANUAL MEMORY has "ERASE" displayed on the screen to erase a TV channel. Press it until MANUAL MEMORY has "ADD" displayed on the screen to store a TV channel. 8. Adjust the volume control and the brightness control on the Monitor for individual preference.

O. Playing a Video Game

There are three jacks on the side of the monitor. The jacks are labeled as: Video Audio L Audio R Plug the video output from your game system into the yellow video jack and the Audio L and Audio R into the applicable jacks. Prior to video game or camcorder use always stop videotape.

P. Wired Headphone

Optional wired headphones may be used with the "Video In a Bag" System. Simply plug in the headset to the headphone jack on the side of the monitor, and both internal speakers will be turned off.
Q. Support External Monitors
Contact an authorized Audiovox dealer for information on ordering an additional external monitors (max number of two external monitors can be supported). Using the DIN cable, connect the external monitor to the MONITOR PORT on the rear of the main unit. The DIN cable supplies 12V DC power, Audio/Video and IR Signals to the monitor.

R. Specification:

Color System:.. NTSC Screen Size:. 5 Inches Remote Control:. Infrared rays Antenna:. External Dipole Antenna TV Channels. 2~6 (VHF low), 7~13 (VHF high), 14~69 (UHF), 1~125 (CATV) TV Reception Sensitivity.20~40 dB Audio Track:. 1 track Tape Width:.. 12.7 mm Tape Speed: SP.. 33.35 mm/s Playback Time:.. 180 Minutes with T-180 Set to the SP Mode Fast/Forward/Rewind Time:. Less than 7 Minutes with T-120 Video Output:.. 1.0 Vp/p, 75 Ohm, unbalanced Video S/N:.. Better than 35 dB Audio Output:.. 2 x 0.5 W Audio S/N:.. Better than 35 dB Power Supply:.. DC 12 V Power Consumption:. 25 W Operating Temperature:.. 41~104 Degrees Fahrenheit (5~40) Degrees Centigrade Operating Humidity:.. 10-75% Storage Temperature:. 4~140 Degrees Fahrenheit (-20~60) Degrees Centigrade Dimensions (W x D x H).10.8" x 13.6" x 4.9" Weight..9.9 lbs
INSTRUCT OPER AT ING INSTRUC T IONS

90 DAY LIMITED WARRANTY

AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 90 days from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor. To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below. This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems. This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/ bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT. This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights, which vary from state to state.

U.S.A.: AUDIOVOX ELECTRONICS CORP., 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 l 1-800-645-4994 CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA

Form No. 128-5047A

Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788

128-6208