Please take a few minutes to read through the ENTIRE INSTRUCTION LEAFLET including the warnings before using your Express II Microwave Steam Sterilizer for the first time. PLEASE RETAIN THESE INSTRUCTIONS. Also available at www.philips.com/AVENT

Assembly and Use

Contents 1. Lid a. Clips 2. Bottle/Accessories Rack b. Dome cap stem c. Bottle cavity d. Nipple cavity e. ISIS Breast Pump slots 3. Base f. Safety grips

I II Before each use

IMPORTANT: Failure to add enough water may cause damage to the Express II Microwave Steam Sterilizer and/or your microwave. Adding too much water may mean your items are not properly sterilized. 2. Put the rack back into the base. 3. Position the lid over the sterilizer base and lock the clips into place until you hear them click. 4. Ensure that the microwave is clean and dry before use Place the sterilizer into the center of the microwave. III Select microwave wattage and timings See Table III do not exceed these times.

IV Aprs chaque cycle

IMPORTANT : Laissez lappareil refroidir au moins deux minutes avant de le retirer du micro-ondes. 1. Retirer le strilisateur du four micro-ondes : Une fois que lappareil a refroidi, retirez-le du micro-ondes en le tenant par la jupe et/ou par les prises de scurit, puis dposez-le sur une surface plane rsistante la chaleur.
NOTE: Les articles restent striliss pendant 24 heures dans le strilisateur vapeur pour micro-ondes Express II si le couvercle nest pas soulev.
Wash all items in warm soapy water and then rinse in water. Wash your hands before handling your sterilized products. 1. Remove rack from the sterilizer and pour 200ml of water into the base.
2. Aprs avoir retir le strilisateur du micro-ondes : Retirez le couvercle en dverrouillant les clips. Lorsque vous soulevez le couvercle, loignez lappareil pour laisser chapper la vapeur. Soin et entretien Videz toujours leau qui reste de la cuve et rincez pour viter lentartrage. Rangez lappareil lorsque sec. Le strilisateur vapeur pour micro-ondes Express II convient au lave-vaisselle.

Loading the sterilizer

Before using the Express II Microwave Steam Sterilizer, always ensure that the items are positioned according to the below loading instructions. A Loading six 4oz/125ml or 9oz/260ml AVENT Airflex Natural Feeding Bottles 1. Position the nipples in the nipple cavities around the dome cap stem. 2. Place the screw rings over the nipples. 3. Place the first three dome caps in the lower slots of the dome cap stem. 4. Place the remaining three dome caps in the upper slots of the dome cap stem. 5. Position the bottles upside down around the previously loaded nipples and screw rings. B Loading three 11oz/330ml Airflex Natural Feeding Bottles 1. Position the nipples in the three nipple cavities surrounding the dome cap stem. 2. Place the screw rings over the nipples. 3. Position the bottles upside down in the three outer nipple cavities. 4. Arrange the three dome caps around the edge of the rack in between the inverted bottles.

C Loading one or two Philips AVENT ISIS Breast Pumps (non-electrical components only) and two 4oz/125ml OR two 9oz/260ml Airflex Natural Feeding Bottles 1. Disassemble the ISIS Breast Pump ensuring the stem is removed from the diaphragm. 2. Position the ISIS Breast Pump bodies into the two slots provided. 3. Position the nipples in the nipple cavities around the dome cap stem. 4. Place the screw rings over the nipples. 5. Place one dome cap in the unobstructed lower slot of the dome cap stem, then the second in the upper slot on top of the inserted dome cap. 6. Position the bottles upside down in the unobstructed bottle cavities. 7. Place the remaining NON-ELECTRICAL pump components in any unobstructed space on the rack. D Loading six 6oz/180ml OR 8oz/240ml VIA Cups and Lids 1. Position the VIA Cups upside down around the dome cap stem. 2. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading.
E Striliser un biberon VIA et de gobelets et couvercles VIA 180 ml OU 240 ml* 1. Insrez la ttine dans la cavit pour ttine extrieure. 2. Placez la bague dtanchit par-dessus la ttine. 3. Disposez les gobelets VIA lenvers autour de la tige centrale. 4. Placez ladaptateur VIA la verticale prs du bord du panier (tel quillustr). 5. Placez les couvercles VIA la verticale aux extrmits du panier, la face interne vers lextrieur. 6. Insrez le capuchon dans lencoche suprieure libre de la tige centrale. F Striliser le biberon naturel AVENT Tempo 1. Ouvrez la bague de verrouillage intrieure de la bague dtanchit et placez la bague dtanchit dans le panier, la languette de verrouillage vers le bas. Assurezvous que les parties de la bague dtanchit qui sont en contact avec la ttine sont tournes vers le haut. 2. Placez la ttine et le capuchon dans le panier comme vous le feriez pour striliser un ensemble biberon. 3. Suivez les directives de strilisation. Striliser dautres accessoires-repas et produits pour bb Lorsque vous strilisez dautres articles NON LECTRIQUES Philips AVENT, veuillez les disposer dans le panier de manire ce que la vapeur puisse circuler librement entre eux.
Philips AVENT est l pour vous aider 1.800.54.AVENT www.philips.com/AVENT
* Comprend un gobelet VIA, son couvercle et son adaptateur, une douce ttine dbit lent supplmentaire, un capuchon et une bague dtanchit
WARNINGS FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE SCALDING OR DAMAGE TO THIS PRODUCT AND/OR YOUR MICROWAVE Always ensure you use 200ml of water before sterilizing. (The unit should be emptied of residual water before each subsequent use.) Always follow loading instructions and do not overload. Do not use bleach or chemical sterilizing solutions/ tablets in sterilizer or on products to be sterilized. Do not sterilize metallic or electronic items in the sterilizer. Do not microwave bottle brush. Always use the appropriate heating time for the power of your microwave unit. (see Table III ) In combination ovens, ensure grill is switched off and has cooled before use. Be sure that the lid is properly fastened to the base before placing in microwave. Always allow at least 2 minutes cooling time before removing from the microwave. Do not remove the lid from the sterilizer immediately after cycle. Allow to cool as the steam will be hot. When removing from microwave, be sure to hold the sterilizer level to avoid leaking or spilling of hot water. When taking the sterilizer out of the microwave, BE CAREFUL it will still be hot. When removing the lid, point it away from you to allow steam to escape. Be careful when handling the sterilized products as they may be hot. Always keep out of reach of children.

NOTE: Do not overload the sterilizer. NOTE: Do not place dome caps in the sterilizer upside down. NOTE: The Express II Microwave Steam Sterilizer is designed to specifically hold the wide shape of Airflex Natural Feeding Bottles. Some products featured may not be available in all countries. Please contact Philips AVENT to check availability.

IV After each cycle

IMPORTANT: Allow the unit to cool for at least two minutes before removing the sterilizer from the microwave. 1. Removing the sterilizer from the microwave: After the unit has cooled, remove it from the microwave by holding the skirt and/or safety grips and then place on an even, heat-resistant surface.
NOTE: Items will remain sterile in the Express II Microwave Steam Sterilizer for up to 24 hours providing the lid is not removed.
2. After removing the sterilizer from the microwave: Remove the lid by unlocking the clips When removing the lid, point it away from you to allow steam to escape. Care and cleaning Always drain the excess water from the unit and rinse to prevent the build up of limescale. Always store when completely dry. The Express II Microwave Steam Sterilizer is dishwasher safe.
E Loading one VIA Feeding System and up to four 6oz/180ml OR 8oz/240ml VIA Cups and Lids* 1. Position the nipple in an outer nipple cavity. 2. Place the screw ring over the nipple. 3. Position the VIA Cups upside down around the dome cap stem. 4. Place the VIA Adaptor on its side around the racks edge (as shown). 5. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading. 6. Place the dome cap in the unobstructed upper slot of the dome cap stem. F To load the AVENT Tempo Natural Feeding Nurser 1. Open the inner locking ring of the screw ring and place the screw ring in the basket with the locking tab facing downwards. Ensure that the parts of the screw ring that are in contact with the nipple are facing upwards. 2. Place the nipple and the dome cap in the basket as you would when sterilizing a bottle assembly. 3. Follow sterilizing instructions. Loading other feeding and baby product items When sterilizing other NON-ELECTRICAL Philips AVENT PRODUCTS simply place the components in the rack allowing enough space so that steam can effectively circulate.
Philips AVENT is here to help 1.800.54.AVENT www.philips.com/AVENT
* Consists of VIA Cup, Lid and Adaptor, an Extra Soft Slow Flow Nipple, Dome Cap and Screw Ring

Ask Philips AVENT

Our customer service is available Monday Friday 9am 5pm (EST) Call Toll Free 474

www.philips.com.au/AVENT

IV Despus de cada ciclo

IMPORTANTE: Deje que la unidad se enfre por un mnimo de dos minutos antes de sacar el esterilizador del microondas. 1. Sacando el esterilizador del microondas: Despus de que la unidad se haya enfriado, squela del microondas sujetando el faldn y/o las empuaduras de seguridad y luego coloque en una superficie plana y resistente al calor.
NOTE: Artculos permanecern estriles en el Esterilizador a Vapor para Microondas por hasta 24 horas si no se quita la tapa.
Wash all items in warm soapy water and then rinse in water. Wash your hands before handling your sterilized products. 1. Remove rack from the sterilizer and pour 200ml of water into the base.
2. Despus de sacar el esterilizador del microondas: Quite la tapa abriendo los ganchos Al quitar la tapa, dirjala en sentido opuesto de usted para permitir que el vapor se escape. Cuidado y limpieza Siempre vace de la unidad cualquier agua que quede y enjuague para prevenir la acumulacin de sarro. Siempre asegure que est completamente seco antes de guardarlo. El Esterilizador a Vapor para Microondas AVENT Express II es a prueba del lavavajillas.

Loading the sterilizer

Before using the AVENT Express II Microwave Steam Sterilizer, always ensure that the items are positioned according to the below loading instructions. A Loading six 4oz/125ml or 9oz/260ml AVENT Natural Feeding Bottles 1. Position the nipples in the nipple cavities around the dome cap stem. 2. Place the screw rings over the nipples. 3. Place the first three dome caps in the lower slots of the dome cap stem. 4. Place the remaining three dome caps in the upper slots of the dome cap stem. 5. Position the bottles upside down around the previously loaded nipples and screw rings. B Loading three 11oz/330ml AVENT Natural Feeding Bottles 1. Position the nipples in the three nipple cavities surrounding the dome cap stem. 2. Place the screw rings over the nipples. 3. Position the bottles upside down in the three outer nipple cavities. 4. Arrange the three dome caps around the edge of the rack in between the inverted bottles.
C Loading one or two AVENT ISIS Breast Pumps (non-electrical components only) and two 4oz/125ml OR two 9oz/260ml AVENT Natural Feeding Bottles 1. Disassemble the ISIS Breast Pump ensuring the stem is removed from the diaphragm. 2. Position the ISIS Breast Pump bodies into the two slots provided. 3. Position the nipples in the nipple cavities around the dome cap stem. 4. Place the screw rings over the nipples. 5. Place one dome cap in the unobstructed lower slot of the dome cap stem, then the second in the upper slot on top of the inserted dome cap. 6. Position the bottles upside down in the unobstructed bottle cavities. 7. Place the remaining NON-ELECTRICAL pump components in any unobstructed space on the rack. D Loading six 6oz/180ml OR 8oz/240ml VIA Cups and Lids 1. Position the VIA Cups upside down around the dome cap stem. 2. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading.

IV After each cycle

IMPORTANT: Allow the unit to cool for at least two minutes before removing the sterilizer from the microwave. 1. Removing the sterilizer from the microwave: After the unit has cooled, remove it from the microwave by holding the skirt and/or safety grips and then place on an even, heat-resistant surface.
NOTE: Items will remain sterile in the AVENT Express II Microwave Steam Sterilizer for up to 24 hours providing the lid is not removed.
2. After removing the sterilizer from the microwave: Remove the lid by unlocking the clips When removing the lid, point it away from you to allow steam to escape. Care and cleaning Always drain the excess water from the unit and rinse to prevent the build up of limescale. Always store when completely dry. The AVENT Express II Microwave Steam Sterilizer is dishwasher safe.
E Loading one VIA Disposable Nurser* and up to four 6oz/180ml OR 8oz/240ml VIA Cups and Lids 1. Position the nipple in an outer nipple cavity. 2. Place the screw ring over the nipple. 3. Position the VIA Cups upside down around the dome cap stem. 4. Place the VIA Adaptor on its side around the racks edge (as shown). 5. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading. 6. Place the dome cap in the unobstructed upper slot of the dome cap stem. Loading other feeding and baby product items When sterilizing other NON-ELECTRICAL AVENT PRODUCTS simply place the components in the rack allowing enough space so that steam can effectively circulate.
NOTE: Do not overload the sterilizer. NOTE: Do not place dome caps in the sterilizer upside down. NOTE: The AVENT Express II Microwave Steam Sterilizer is designed to specifically hold the wide shape of AVENT Natural Feeding Bottles. * Consists of VIA Cup, Lid and Adaptor, an Extra Soft Slow Flow Nipple, Dome Cap and Screw Ring
Some products featured may not be available in all countries. Please contact AVENT to check availability.
AVENT is here to help 1.800.54.AVENT www.aventamerica.com
Strilisateur vapeur pour micro-ondes Express II AVENT
MISE EN GARDE POUR VITER LCAILLAGE OU DES DOMMAGES CET APPAREIL ET/OU VOTRE FOUR, VEUILLEZ SUIVRE ATTENTIVEMENT CES DIRECTIVES Versez toujours 200 ml deau avant chaque utilisation. (Il faut vider leau qui reste aprs chaque utilisation.) Suivez toujours les instructions sur la disposition des accessoires et ne surchargez pas. Ne mettez pas de javellisant ou de pastille/solution chimique de strilisation dans le strilisateur ou sur les accessoires tre striliss. Ne strilisez pas darticles mtalliques ou lectroniques dans le strilisateur. Ne mettez pas le goupillon au micro-ondes. Utilisez toujours le temps de chauffe correspondant au niveau de puissance de votre four micro-ondes. (voir Tableau III ) Dans les fours combins, assurez-vous que le grill est teint et quil a refroidi avant dy mettre votre strilisateur. Assurez-vous que le couvercle est verrouill avant de placer votre strilisateur au micro-ondes. Accordez toujours 2 minutes de refroidissement avant de retirer le strilisateur du four. Ne retirez pas le couvercle du strilisateur immdiatement aprs un cycle. La vapeur qui pourrait schapper est brlante. Attendez que le strilisateur refroidisse. Lorsque vous retirez le strilisateur du micro-ondes, tenez-le bien droit pour viter les fuites deau chaude. Lorsque vous retirez le strilisateur du microondes, PRENEZ GARDE : il sera encore trs chaud. Quand vous soulverez le couvercle, loignez-le de vous pour permettre la vapeur de schapper. Prenez garde lorsque vous manipulez les articles striliss, ils pourraient encore tre chauds. Tenez hors de porte des jeunes enfants.