Contents 1. Lid a. Clips 2. Bottle/Accessories Rack b. Dome cap stem c. Bottle cavity d. Nipple cavity e. ISIS Breast Pump slots 3. Base f. Safety grips

I II Before each use

IMPORTANT: Failure to add enough water may cause damage to the Express II Microwave Steam Sterilizer and/or your microwave. Adding too much water may mean your items are not properly sterilized. 2. Put the rack back into the base. 3. Position the lid over the sterilizer base and lock the clips into place until you hear them click. 4. Ensure that the microwave is clean and dry before use Place the sterilizer into the center of the microwave. III Select microwave wattage and timings See Table III do not exceed these times.

IV Aprs chaque cycle

IMPORTANT : Laissez lappareil refroidir au moins deux minutes avant de le retirer du micro-ondes. 1. Retirer le strilisateur du four micro-ondes : Une fois que lappareil a refroidi, retirez-le du micro-ondes en le tenant par la jupe et/ou par les prises de scurit, puis dposez-le sur une surface plane rsistante la chaleur.
NOTE: Les articles restent striliss pendant 24 heures dans le strilisateur vapeur pour micro-ondes Express II si le couvercle nest pas soulev.
Wash all items in warm soapy water and then rinse in water. Wash your hands before handling your sterilized products. 1. Remove rack from the sterilizer and pour 200ml of water into the base.
2. Aprs avoir retir le strilisateur du micro-ondes : Retirez le couvercle en dverrouillant les clips. Lorsque vous soulevez le couvercle, loignez lappareil pour laisser chapper la vapeur. Soin et entretien Videz toujours leau qui reste de la cuve et rincez pour viter lentartrage. Rangez lappareil lorsque sec. Le strilisateur vapeur pour micro-ondes Express II convient au lave-vaisselle.

Loading the sterilizer

Before using the Express II Microwave Steam Sterilizer, always ensure that the items are positioned according to the below loading instructions. A Loading six 4oz/125ml or 9oz/260ml AVENT Airflex Natural Feeding Bottles 1. Position the nipples in the nipple cavities around the dome cap stem. 2. Place the screw rings over the nipples. 3. Place the first three dome caps in the lower slots of the dome cap stem. 4. Place the remaining three dome caps in the upper slots of the dome cap stem. 5. Position the bottles upside down around the previously loaded nipples and screw rings. B Loading three 11oz/330ml Airflex Natural Feeding Bottles 1. Position the nipples in the three nipple cavities surrounding the dome cap stem. 2. Place the screw rings over the nipples. 3. Position the bottles upside down in the three outer nipple cavities. 4. Arrange the three dome caps around the edge of the rack in between the inverted bottles.
C Loading one or two Philips AVENT ISIS Breast Pumps (non-electrical components only) and two 4oz/125ml OR two 9oz/260ml Airflex Natural Feeding Bottles 1. Disassemble the ISIS Breast Pump ensuring the stem is removed from the diaphragm. 2. Position the ISIS Breast Pump bodies into the two slots provided. 3. Position the nipples in the nipple cavities around the dome cap stem. 4. Place the screw rings over the nipples. 5. Place one dome cap in the unobstructed lower slot of the dome cap stem, then the second in the upper slot on top of the inserted dome cap. 6. Position the bottles upside down in the unobstructed bottle cavities. 7. Place the remaining NON-ELECTRICAL pump components in any unobstructed space on the rack. D Loading six 6oz/180ml OR 8oz/240ml VIA Cups and Lids 1. Position the VIA Cups upside down around the dome cap stem. 2. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading.

E Striliser un biberon VIA et de gobelets et couvercles VIA 180 ml OU 240 ml* 1. Insrez la ttine dans la cavit pour ttine extrieure. 2. Placez la bague dtanchit par-dessus la ttine. 3. Disposez les gobelets VIA lenvers autour de la tige centrale. 4. Placez ladaptateur VIA la verticale prs du bord du panier (tel quillustr). 5. Placez les couvercles VIA la verticale aux extrmits du panier, la face interne vers lextrieur. 6. Insrez le capuchon dans lencoche suprieure libre de la tige centrale. F Striliser le biberon naturel AVENT Tempo 1. Ouvrez la bague de verrouillage intrieure de la bague dtanchit et placez la bague dtanchit dans le panier, la languette de verrouillage vers le bas. Assurezvous que les parties de la bague dtanchit qui sont en contact avec la ttine sont tournes vers le haut. 2. Placez la ttine et le capuchon dans le panier comme vous le feriez pour striliser un ensemble biberon. 3. Suivez les directives de strilisation. Striliser dautres accessoires-repas et produits pour bb Lorsque vous strilisez dautres articles NON LECTRIQUES Philips AVENT, veuillez les disposer dans le panier de manire ce que la vapeur puisse circuler librement entre eux.
Philips AVENT est l pour vous aider 1.800.54.AVENT www.philips.com/AVENT
* Comprend un gobelet VIA, son couvercle et son adaptateur, une douce ttine dbit lent supplmentaire, un capuchon et une bague dtanchit
WARNINGS FAILURE TO FOLLOW INSTRUCTIONS MAY CAUSE SCALDING OR DAMAGE TO THIS PRODUCT AND/OR YOUR MICROWAVE Always ensure you use 200ml of water before sterilizing. (The unit should be emptied of residual water before each subsequent use.) Always follow loading instructions and do not overload. Do not use bleach or chemical sterilizing solutions/ tablets in sterilizer or on products to be sterilized. Do not sterilize metallic or electronic items in the sterilizer. Do not microwave bottle brush. Always use the appropriate heating time for the power of your microwave unit. (see Table III ) In combination ovens, ensure grill is switched off and has cooled before use. Be sure that the lid is properly fastened to the base before placing in microwave. Always allow at least 2 minutes cooling time before removing from the microwave. Do not remove the lid from the sterilizer immediately after cycle. Allow to cool as the steam will be hot. When removing from microwave, be sure to hold the sterilizer level to avoid leaking or spilling of hot water. When taking the sterilizer out of the microwave, BE CAREFUL it will still be hot. When removing the lid, point it away from you to allow steam to escape. Be careful when handling the sterilized products as they may be hot. Always keep out of reach of children.

NOTE: Do not overload the sterilizer. NOTE: Do not place dome caps in the sterilizer upside down. NOTE: The Express II Microwave Steam Sterilizer is designed to specifically hold the wide shape of Airflex Natural Feeding Bottles. Some products featured may not be available in all countries. Please contact Philips AVENT to check availability.

IV After each cycle

IMPORTANT: Allow the unit to cool for at least two minutes before removing the sterilizer from the microwave. 1. Removing the sterilizer from the microwave: After the unit has cooled, remove it from the microwave by holding the skirt and/or safety grips and then place on an even, heat-resistant surface.
NOTE: Items will remain sterile in the Express II Microwave Steam Sterilizer for up to 24 hours providing the lid is not removed.
2. After removing the sterilizer from the microwave: Remove the lid by unlocking the clips When removing the lid, point it away from you to allow steam to escape. Care and cleaning Always drain the excess water from the unit and rinse to prevent the build up of limescale. Always store when completely dry. The Express II Microwave Steam Sterilizer is dishwasher safe.
E Loading one VIA Feeding System and up to four 6oz/180ml OR 8oz/240ml VIA Cups and Lids* 1. Position the nipple in an outer nipple cavity. 2. Place the screw ring over the nipple. 3. Position the VIA Cups upside down around the dome cap stem. 4. Place the VIA Adaptor on its side around the racks edge (as shown). 5. Position the VIA Lids vertically around the racks edge. Rims should face out for easier loading. 6. Place the dome cap in the unobstructed upper slot of the dome cap stem. F To load the AVENT Tempo Natural Feeding Nurser 1. Open the inner locking ring of the screw ring and place the screw ring in the basket with the locking tab facing downwards. Ensure that the parts of the screw ring that are in contact with the nipple are facing upwards. 2. Place the nipple and the dome cap in the basket as you would when sterilizing a bottle assembly. 3. Follow sterilizing instructions. Loading other feeding and baby product items When sterilizing other NON-ELECTRICAL Philips AVENT PRODUCTS simply place the components in the rack allowing enough space so that steam can effectively circulate.
Philips AVENT is here to help 1.800.54.AVENT www.philips.com/AVENT
* Consists of VIA Cup, Lid and Adaptor, an Extra Soft Slow Flow Nipple, Dome Cap and Screw Ring

Ask Philips AVENT

Our customer service is available Monday Friday 9am 5pm (EST) Call Toll Free 474

www.philips.com.au/AVENT

Spare Parts are available at www.bpmchildcare.com
Distributed in Australia by BPM Childcare www.bpmchildcare.com

Pierwsza pomoc

Sterylizator nie wcza si Zbyt duo pary wydostaje si spod pokrywy Na artykuach poddanych sterylizacji powstaje osad Czas sterylizacji jest zbyt dugi Sprawd prawidowo woenia wtyczki oraz czy jest napicie w gniazdku. Artykuy s nieprawidowo uoone. Sprawd ich uoenie posikujc si rysunkiem.
Ze sterylizatora trzeba usun kamie (zobacz w instrukcji usuwania kamienia).
Zbyt duo wody wlaa do sterylizatora. Stosuj dokadnie 90ml wody. LUB: Do sterylizatora woya za mao artykuw niewielkie zaadowanie przedua sterylizacj.
Philips AVENT Express Electric Steam Steriliser
Please take 5 minutes to read through the whole of this leaflet before you use your Philips AVENT Express Electric Steam Steriliser for the first time. As well as bottles and breastfeeding accessories, you can sterilise any other boilable items (please refer to the manufacturers instructions regarding sterilisation). Please keep these instructions safe for future use. These instructions are also available on our website. NB: When loading, always ensure that the steam can effectively circulate around all surfaces and that any water can drain off easily. 8) Removed items must be used/assembled immediately or re-sterilised. Expressed milk can be stored in a sterile breast milk container in the refrigerator for up to 48 hours (not in the door) or in the freezer for up to 3 months. Infant formula should be made up fresh for each feed. 9) The steriliser must be left to cool for at least 10 minutes between each use to allow the thermostat to reset. 10) After each use, pour away any remaining water, rinse and wipe dry.

Warnings

1) Under no circumstances should anything other than citric acid or vinegar be used for de-scaling as it may cause irreparable damage. 2) Do not use bleach or chemical sterilising solutions/tablets in your steam steriliser or on products to be sterilised. 3) Do not use abrasive, anti-bacterial materials or scourers to clean the steriliser. 4) Do not use softened water in the steriliser. 5) The lead supplied must not be used on any other appliance and no other lead should be used with the Express Electric Steam Steriliser. 6) This appliance is intended for use by responsible persons, Keep out of reach of small children and the infirm. 7) This appliance is not intended for use by persons including children with reduced physical, sensory or mental capabilities, or lack of experience or knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. 8) Children should be supervised to ensure that they do not play with the appliance.

To sterilise up to six 260ml, 125ml or 330ml AVENT Bottles (see diagram C)
1) Slide the lower basket onto the central stem. 2) Thread 2 screw rings onto the central stem. 3) Slide the bottle rack down the central stem, with the neck facing down, until it rests on the top screw ring. 4) Place the teats through the centre of the holes in the bottle rack onto the lower basket. 5) Thread 4 screw rings onto the central stem. 6) Place the 6 inverted bottles in the bottle rack. 7) Push the upper basket onto the central stem until it rests on the catch. Place the 6 dome caps and tongs into the upper basket. 8) The upper basket is not required when sterilising 330ml bottles (see diagram C8). 9) Place the assembled unit into the steriliser body and put the lid on. 10) Put the lead into the back of the steriliser body and plug into the mains supply. Switch on. 11) Cycle times will vary depending on the load. After each cycle the unit will switch off automatically and the light will go out (approx. cycle time: 8 minutes).

Hazard Warning

When in use, the steriliser contains boiling water and steam escapes from the vent in the lid. Ensure the steriliser is placed on a firm level surface when in use. Never open the unit when in use. Always keep out of reach of children. Always unplug from the mains when not in use. Never place items on top of the steriliser. To stop the steriliser during the cycle, unplug at the mains. Take care when opening as steam can burn. Never immerse the steriliser in water. Never use the steriliser without water. Failure to follow de-scaling instructions may cause irreparable damage. There are no servicable parts inside the Express Electric Steam Steriliser. Do not attempt to open, service or repair the Express Electric Steam Steriliser yourself.
Dishwasher Basket (see diagram F)
1) The upper and lower baskets can be clipped together to hold small items such as teats, breast pump parts, soothers, etc for washing in the top rack of your dishwasher prior to sterilisation. 2) To clip together, align the two baskets so that the indicators are opposite each other and snap the baskets together. To open basket, pull apart with fingers using side recesses. Warning: If your Philips AVENT items are washed in the dishwasher with dirty items covered with remnants of strong sauces, such as tomato sauce, they may discolour over time.

Care of your steriliser

You should de-scale your steriliser every four weeks to ensure it continues to work 100% effectively. It may be advantageous to use pre-boiled or filtered water in your steriliser in order to reduce limescale build up. EITHER: 1) Mix one sachet of citric acid (10gms) with 200ml of water. Pour into the empty steriliser. Do not put lid on. Switch on for 1-2 minutes, i.e. do not run a full cycle. Switch off at mains and leave to stand for 30 minutes. Drain and rinse out the steriliser. Run a full cycle empty with the lid on, using exactly 90ml of water. Wipe out the steriliser. (Citric Acid is available from most chemists avoid contact with eyes as this may cause irritation. Keep out of reach of children.) OR: 2) Pour 100ml vinegar mixed with 200ml cold water into steriliser. Allow to stand in the unit until any limescale has dissolved. Empty the unit and rinse thoroughly.

Guarantee

Philips AVENT guarantees that should the Express Electric Steam Steriliser become faulty during twelve months from the date of purchase, it will be replaced free of charge during this time. Please return it to the retailer where it was purchased. Please keep your receipt as a proof of purchase, together with a note of when and where purchased. For the guarantee to be valid, please note: The Express Electric Steam Steriliser must be used according to the instructions in this leaflet and connected to suitable electricity supply. The claim must not be a result of accident, misuse, dirt, neglect or fair wear and tear. This does not affect your statutory rights. Philips AVENT is here to help GB: Call FREE on 064 IRL: Call FREE on 021 AU: AVENT Ltd, Suffolk, CO10 7QS, England

Contents (see diagram A)

a) Lid b) 2 x Upper basket c) Bottle rack d) Lower basket e) Central stem f) Steriliser body g) Measuring cup h) Lead and plug i) Tongs NB: Upper and lower baskets are identical
To sterilise the Philips AVENT ISIS Manual Breast Pump (see diagram D)
1) Click the ISIS Breast Pump body into the slot in the upper basket and arrange the other breast pump components as shown. Assemble remaining components of the ISIS Breast Pump in the lower basket. 2) Up to six bottles (not including screw rings, teats or dome caps) can be sterilised with the pump. 3) Place assembled unit into the steriliser body, put the lid on. 4) Put the lead into the back of the steriliser body and plug into the mains supply. Switch on.

Before using your steriliser for the first time
(see diagram B) Remove all items from inside the steriliser body. 1) Pour in exactly 90ml of tap water. 2) Assemble all the blue components (baskets, stem and bottle rack). Place the assembled components in the steriliser and put the lid on. 3) Connect the lead into the back of the steriliser and plug into the mains supply. The light should come on automatically. If it does not, press down on the steriliser switch. 4) At the end of the cycle the unit will switch off automatically and the light will go out. 5) Allow unit to cool, turn off at the mains, unplug and disconnect the lead from the back of the steriliser. 6) Remove baskets and bottle rack, pour away any remaining water and wipe dry.
To sterilise narrow neck bottles and other feeding items
Teats should be placed around the central stem in the lower basket and screw rings in the top basket, as they are too narrow for the stem. Always ensure items are positioned within baskets /racks to ensure effective circulation of steam. The bottle rack and/or upper basket can be removed to make more room.

Before each use

1) Before sterilising, wash all items in mild soapy water and rinse. 2) Pour exactly 90ml of water into the steriliser body. If you add more than 90ml you will prolong the cycle time. If you use less than 90ml, your items may not be properly sterilised.
After sterilisation (see diagram E) 1) Do not remove the lid straight away. Let the steriliser cool down for 3 minutes. 2) Turn off at the mains, unplug and disconnect the lead from the back of the steriliser. 3) Wash your hands thoroughly before removing the sterilised items. 4) Remove the lid. 5) If necessary, shake excess water from items before assembling. 6) The tongs can be used to remove small items and to pull the sterile teats through the screw rings of the bottles. 7) The contents will remain sterile for up to six hours, following the end of the cycle, provided the lid is not removed.

Troubleshooting guide

Steriliser will not work Check that the mains lead is connected to the steriliser as well as plugged into the mains. Check fuse in plug. Parts incorrectly loaded. Refer to diagrams C/D.
Excessive steam escaping from under the lid Bottles come out with marks Steriliser takes too long to switch off
Steriliser needs de-scaling (see section headed Care of your steriliser). Too much water is being used. Use exactly 90ml of water, OR: The steriliser is loaded with only a few items light loads will take longer to cycle.

Ask Philips AVENT

Our customer service is available Monday Friday 9am 5pm (EST) Call Toll Free 474