IMPORTANT SAFETY INFORMATION

1) 2) 3) 4) 5)

Important Safety Instructions / Specifications...2 Important Information....3 Amplifier Descriptions...4 Set-up & Warranty Information...5-7 Contact Information....8

CAUTION

INSIDE THIS INSTRUCTION MANUAL
Read these instructions. Follow all instructions Keep these instructions Heed all warnings Do not use the MATRIX 1000 near water. Be extra cautious when moving the system during rain or while transporting the system over wet surfaces as water might splash onto the amplifier. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with manufacturers instructions. 8) Do not install near heat sources such as radiators, stoves or other devices that may produce heat. 9) Do not defeat the safety purpose of the polarization or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched, particularly at the plug and the point where it exits the MATRIX 1000 amplifier. 11) Only use attachments / accessories specified by B-52 Pro-Audio. 12) Use caution when transporting the system to avoid injury from tip-over. 13) Unplug the MATRIX 1000 during lightning storms and when not in use. 14) Refer all servicing to qualified to personnel. Servicing is required when the MATRIX 1000 has been damaged in any way such as when power-cord or plug is damaged, liquid has been spilled into the cabinets, the unit has been exposed to moisture or rain, does not operate normally, or has been dropped. 15) To reduce the risk of fire or electric shock, do not expose the MATRIX 1000 to rain or moisture. 16) The MATRIX 1000 is not intended for outdoor fixed installations or in high moisture areas. Moisture can damage the speakers and can use cause corrosion of electrical contacts. Keep speakers out of extended or intense direct sunlight. The subwoofer spider and surround will prematurely dry out and finished surfaces may fade and be damaged by longterm exposure to intense ultra-violent light.

HEED ALL WARNINGS

RISK OF ELECTRIC SHOCK DO NOT OPEN
WARNING: To reduce the risk or fire or electrical shock do not expose this equipment to rain or moisture.
AMPLIFIER SPECIFICATIONS: Subwoofer Power Output: 400 W / 8 Ohms @ 1% THD 10 Two-way Power Output: 150 W / 4 Ohms @ 1% THD Line in: XLR Female Parallel out: XLR Male Input Impedance: 48 k Ohms Speaker Out: Speakon NL4 Style Connector Power Requirement: 115V<>50/60Hz<>10A 230V<>50/60Hz<>6A ACTIVE CROSSOVER: Crossover Frequency: 120 Hz; 24 dB/ Octave SUBWOOFER: Speaker: Nominal Impedance: Subwoofer Freq. Response: Sound Pressure Level (1w/1m): Max. SPL: Weight: Dimensions (Transport): 10 TWO-WAY SPEAKERS: Speaker Input:
CAUTION: Connect the power cable only after you have absolutely made sure that the local mains voltage matches the voltage specified on the device. If you connect to the wrong voltage, you may destroy the electronic components of the MATRIX 1000 system. See page 4 for a complete description of factory-default voltage settings.
1 x 15 Custom Built B-52 Subwoofer 8 Ohms 40 Hz 120 Hz +/- 3dB 102 dB (half space) 127 dB @10% THD 115 lbs 28 (H) x 19 (W) x 23 (D)
Speakon style connector (pin 1+ = +, pin 1- = -) LF/MF Woofer: 1 x 10 Custom Built B-52 Transducer HF Driver: 1 x 3/4 Titanium Diaphragm on CD Horn HF Dispersion: 90O x 40O Nominal Impedance: 4 Ohms Active Freq. Response: 120 19K Hz +/- 3dB Crossover Frequency (passive): 2.5 kHz; 12 dB / Octave Sound Pressure Level (1w/1m): 101 dB (half space) Max. SPL: 124 dB @10% THD Weight: 25 lbs Dimensions (Upright): 19 (H) x 12 (W) x 11 (D) COMPLETE SYSTEM: Weight: Dimensions (Transport): 165 lbs 39 (H) x 19 (W) x 23 (D)

Note: Specifications are subject to change without notice
Congratulations on your purchase of this B-52 Professional MATRIX 1000 V2.
The MATRIX 1000 V2 Active Speaker System
The MATRIX 1000 system is a complete sound reinforcement solution consisting of two 10 two-way speakers and an active 15 subwoofer. The subwoofer enclosure is equipped with a three channel amplifier and all the electronics required to run the system. The electronic circuitry was fine tuned to match the two-way speakers for the best possible sound. This system was designed for easy operation since you do not need to worry about tweaking frequencies and finessing levels. All you have to do is set up the system components, connect the XLR right and left signal cables, speaker cables and power cords and youre ready to go.

SUBWOOFER:

The 15 subwoofer enclosure is divided into two separate compartments. The front chamber serves as the cabinet for the 15 subwoofer. The rear chamber houses all of the systems electronic circuitry, which includes the amplification for all three components, power supply and preamps. The 15 subwoofer has a power handling capability of 400 watts and a nominal impedance of 8 ohms.

10 TWO-WAY SPEAKERS:

The two 10 two-way speakers are loaded with B-52s custom 10 speakers and a 3/4 titanium diaphragm compression driver, mounted to a 900 x 400 constant directivity horn. The speakers are designed to be pole mounted, can sit as stage monitors and have built-in (3/TPI) flying hardware for permanent installations. The front panel of both two-way speakers is concaved so as to fit perfectly onto the subwoofers front grille for easy transport. Each two-way speaker has the power handling capability of 150 watts and a nominal impedance of 4 ohms.
10 TWO-WAY SPEAKER INPUT:
Caution: The systems components are matched for the best possible sound quality and may only be operated in the specified configuration provided in this manual. Use of other two-way speakers may hinder the sound quality and can damage the power amplifier.
To establish a connection, plug the connector and then rotate it until it engages. Before you unplug it, you will first need to disengage the safety catch. To accomplish this, pull the bayonet catch towards the cable. (Pin 1+ = +, Pin 1- = -).

TRANPORTING THE SYSTEM:

To transport the system, simply set the subwoofer on its casters and place the two 10 two-way speakers onto the subwoofers front panel facing down. Secure them with the included locking strap by fastening it to the bar handles on the side on the subwoofer cabinet. Place the included cover over the entire system and you are ready to move the system with ease.

B-52 Pro-Audio speakers, including the MATRIX 1000, are capable of producing sound pressure levels (SPL) sufficient to cause permanent hearing damage to performers, production crews or people in the audience. Hearing protection devices such ear-plugs are recommended. Caution should be taken to avoid extended SPL is excess of 90 dBA. Do not attempt to service the MATRIX 1000 by yourself. Refer all servicing to a B-52 Pro-Audio Authorized dealer. Service is required when the MATRIX 1000 has had liquid spilled on or inside the subwoofer or speakers, has been damaged in any way, the speaker has been exposed to rain or moisture, does not operate normally or has been dropped. To reduce the risk of fire or electrical shock, do not expose this unit to rain or moisture. Do not operate your MATRIX 1000 near a pool or other standing water. Make sure all blades on the polarized power plug are fully inserted into the power source. Ensure the power cord is not stretched, pinched or otherwise abused. Ensure the power cord is routed to avoid foot traffic. Your MATRIX 1000 amplifier should be cleaned only with a dry cloth. 1) 2) 3) 4) 5) 6) Do not hang the speakers by yourself. You must have a professional and licensed contractor hang the speakers. Speakers not properly flown/hung can fall causing injury or extreme cases, death. B-52 Pro-Audio speakers, especially the MATRIX 1000, can produce high-levels of energy. When placed on slippery surfaces such as polished wood or smooth tiles, the subwoofer may move because of its intense bass output. Precautions should be taken to ensure the subwoofer does not fall off a stage or raised surface. Turn the gain knobs all the way down when turning the system on or off. Make sure the active subwoofer is connected to the two-way speakers before powering the system up. Make sure your mixer and all other signal sources are turned on before connecting the MATRIX 1000. The MATRIX 1000 should always be switched on last, after you switch on all connected devices.
Hearing damage, prolonged exposure to excessive SPL
Amplifier Module Precautions

WARNING Shock Hazard:

Caution:

DESCRIPTIONS

1. 2. 3. AMPLIFIER: The Matrix 1000 amplifier panel. LEFT SPEAKER OUTPUT: Speakon-style connector output for left monitor. COOLING FANS: Rear cooling fans for built-in 3-channel amplifier. Ensure these cooling fans are clear of external obstructions for efficient operation. POWER CORD CONNECTOR: For attachment of the included power cord. FUSE HOLDER: Contains primary fuse. See warning below for important safety information. POWER ON/OFF SWITCH: Turns the Matrix 1000 on or off. VOLTAGE SWITCH: Enables the Matrix 1000 to be switched from 115 volts to 230 volts. See warning below for important safety information. RIGHT SPEAKER OUTPUT: Speakon-style connector output for right monitor. PHASE SWITCH: Sets the polarity of the Matrix 1000. SUBWOOFER GAIN CONTROL: Controls the levels of Gain to the subwoofer. GROUND/LIFT SWITCH: Remove ground from circuit to eliminate excessive 60-cycle hum. RIGHT MONITOR GAIN CONTROL: Controls the levels of Gain to the right side full range speaker. XLR BALANCED RIGHT FULL-RANGE OUTPUT: Sends parallel full range signal out to other systems or components. XLR BALANCED RIGHT FULL-RANGE INPUT: Connects the right side full range speaker to your mixing console. LEFT MONITOR GAIN CONTROL: Controls the levels of Gain to the left side full range speaker. XLR BALANCED LEFT FULL-RANGE OUTPUT: Sends parallel full range signal out to other systems or components. XLR BALANCED LEFT FULL-RANGE INPUT: Connects the left side full range speaker to your mixing console. LEFT CHANNEL CONTROLS RIGHT CHANNEL CONTROLS

4. 5. 6. 7.

NOTE: Use Pin #: 1+ and 1-

8. 9. 10. 11. 12. 13.

15. 16.

17. 18. 19.

IMPORTANT: VOLTAGE SWITCH & FUSE HOLDER
U.S.A Customers: The MATRIX 1000 is already positioned to the correct voltage (115v) and also includes the correct fuse. DO NOT change the position of the switch described in (7) above prior to operation in the U.S. International Customers: The Matrix 1000 is shipped internationally from our U.S. factory, with the voltage switch and fuse correctly set to your countrys requirements. DO NOT change the position of the switch described in (7) above prior to operation.
GETTING TO KNOW YOUR MATRIX 1000 V2 SUBWOOFER AMPLIFIER
The MATRIX 1000 consists of one subwoofer and two 10 two-way speakers. Connect the right and left signals from your mixer (master left/right, line out) to the balanced input sockets of the MATRIX 1000 using standard XLR cables.

Setting Up Your MATRIX 1000 V2 Speaker System

MONO SET-UP

Mixer / Sound Source

FESSIONAL

PR OFESSIONAL

to left 10 two-way

to right 10 two-way
Left & Right Gain Controls: After turning on your MATRIX 1000 using the on/off switch located on the rear amplifier plate of the active subwoofer, set the LEFT and RIGHT Gain controls to the center position (or facing straight up). This is the ideal position to operate the MATRIX 1000 if you have connected a mixer to the system. Alternatively, if you have connected a CD Player or other sound source, it is recommend that the Gain controls are turned all the way clockwise to achieve peak volume. During performance, if your MATRIX 1000 shows signs of distortion, check the sound source and, if applicable, reduce the sound levels. If it is not possible to reduce the sound levels at the source, simply turn down the gain levels on the rear amplifier panel of the MATRIX 1000.

SETTINGS

Caution: The Left and Right 10 two-way outputs are designed for a nominal impedance of 4 ohms. Under no circumstance may the impedance dip below the value as this might damage the MATRIX 1000 amplifier.
Subwoofer Level Control: It is recommended to set the Subwoofer Gain control to halfway. At this position and with the 10 Two-way speakers set in a similar position the MATRIX 1000 should be perfectly balanced. If you wish to add bass, simply turn up the Subwoofer Gain control.

STEREO SET-UP

Ground Lift Switch: At times you may experience a low-frequency hum. At this time, engage the ground lift switch to eliminate this hum. If this does not eliminate the hum, please check cabling and sound sources.
CAUTION: Connect the power cable only after you have absolutely made sure that the local mains voltage matches the voltage specified on the device. If you connect to the wrong voltage, you may destroy the electronic components of the MATRIX 1000 system.

DUAL SET-UP

MIXER / SOUND SOURCE

FESS IONAL

FES SIONAL

Using a dual MATRIX 1000 system will cover a wider area and can be used for a larger audience. Connect the LEFT output from your mixer to the systems INPUT LEFT. Take a short XLR cable and connect one end of it from the THROUGH LEFT output to the INPUT
B-52 CABINETS: E.T.I. Sound Systems, Inc. offers a LIFETIME warranty (effective January 1, 2002) to the original purchaser that a B-52's cabinet construction will be free from defects in material and workmanship. A dated sales receipt will establish coverage under this warranty. This warranty does not cover service or parts to repair damage caused by neglect, abuse, normal & wear and cosmetic appearance of the cabinetry not directly attributed to defects in material or workmanship, or service, repair, modifications of the cabinet, which has not been authorized or approved by E.T.I. If this product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. LOUDSPEAKER AND MID-RANGE COMPONENTS: E.T.I. Sound Systems, Inc. warrants the original purchaser that B-52 loudspeakers and/or midrange components will be free from defects in material and workmanship for a period of (5) FIVE YEARS from the original purchase date (effective January 1, 2002). A dated sales receipt will establish coverage under this warranty. This warranty will automatically terminate (5) years after the original retail sales date. This (5) five-year warranty does not cover service or parts to repair damage caused by accident, disaster, misuse, abuse, burnt voice-coils, over-powering, negligence, inadequate packing or shipping procedures and service, repair or modifications of the component which has not been authorized or approved by E.T.I. This warranty is in lieu of all other expressed warranties. If this product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above.
Thank you for choosing a B-52 sound product. B-52 manufactures some of the worlds best sounding and most reliable professional speaker systems, amplifiers and components. E.T.I. Sound Systems, Inc., makers of B-52, takes great pride in thoroughly testing each B-52 product prior to shipment.

Limited Warranty

RIGHT. This will feed both satellites the same LEFT signal. Connect the RIGHT output from your mixer to the systems INPUT RIGHT. Take a short XLR cable and connect one end of it from the THROUGH RIGHT output to the INPUT LEFT. This will feed both satellites the same RIGHT signal.
This Limited Warranty is effective as of January 1, 2002. Any warranty claim on B-52 products purchased before this date may be subject to monetary charges. Warranty valid ONLY to original purchaser with PROOF OF PURCHASE.
HIGH-FREQUENCY DEVICES: E.T.I. Sound Systems, Inc. offers a LIFETIME warranty (effective January 1, 2002) to the original purchaser that B-52 high frequency (tweeters) devices will be free from defects in material and workmanship. A dated sales receipt will establish coverage under this warranty. This warranty does not warranty neglect or abuse. NO WARRANTY IS OFFERED ON HIGH-FREQUENCY DEVICES IN B-52 SYSTEMS WITH A BI-AMP SWITCH OPTION. The lifetime warranty on high-frequency devices does not cover service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures or service, repair or modifications of the product which has not been authorized or approved by E.T.I. This warranty is in lieu of all other expressed warranties. If this product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. AMPLIFIERS: E.T.I. Sound Systems, Inc. warrants the original purchaser that B-52 amplifiers will be free from defects in material and workmanship for a period of (2) TWO YEARS from the original purchase date (effective January 1, 2002). A dated sales receipt will establish coverage under this warranty. This warranty will automatically terminate (2) years after the original retail sales date. This (2) two-year warranty does not cover service or parts to repair damage caused by accident, disaster, misuse, abuse, over-powering, negligence, inadequate packing or shipping procedures and service, repair or modifications of the amplifier which has not been authorized or
NEVER RETURN THE ENTIRE CABINET__JUST THE DEFECTIVE COMPONENT. Identify and remove the defective component. If you are uncertain which component is defective, or need directions for removing a component, please contact our Customer Service Department for assistance. Components which are a part of an original B-52 speaker box must be sent directly to E.T.I. Products must be shipped in the original packaging or its equivalent; in any case, the risk of loss or damage in transit is to be borne by the purchaser. The Return Authorization Number must appear in large print directly below the shipping address. Always include a brief description of the defect, along with your correct return address and telephone number. When calling to inquire about a returned product, always refer to the Return Authorization Number. If E.T.I. determines that the unit was defective in materials or workmanship at any time during the warranty period, E.T.I. has the option of repairing or replacing the product at no additional charge, except as set forth below. All replaced parts become a property of E.T.I. Products replaced or repaired under this warranty will be returned via ground-shipping-within the United States-freight prepaid. E.T.I. is not responsible for costs associated with expedited shipping, either to E.T.I. or the return of the product to the customer.

RETURN PROCEDURES: In the unlikely event that a defect should occur, follow the procedure outlined below. Defective products must be shipped, together with proof of purchase, freight pre-paid and insured to the Authorized B-52 Dealer from whom you purchased the product or directly to E.T.I. Sound Systems. If a product must be returned to E.T.I. Sound Systems for warranty replacement/repair, a Return Authorization Number must be obtained from our Customer Service Department prior to shipping the product.
approved by E.T.I. This warranty is in lieu of all other expressed warranties. If this product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above.
INCIDENTAL OR CONSEQUENTIAL DAMAGE: In no event will E.T.I. be liable for any incidental or consequential damages arising out of the use or inability to use of any B-52 product, even if E.T.I. or a B-52 dealer has been advised of the possibility of such damages, or any other claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you. This warranty gives you specific legal rights and you may also have other rights which may vary from state to state.
FOR YOUR PROTECTION: Please complete and mail the Purchase Information Card within (10) ten days of the date of purchase so that we may contact you directly in the event a safety notification issued in accordance with the 1972 Consumer Product Safety Act. In addition, we ask that you complete the brief questionnaire so me may analyze your answers and in this way, help us evaluate our customer needs. CUSTOMER SERVICE: Our dedicated staff is ready to help you with any B-52 warrant or product questions you may have. Please call 323-277-4100 (9:00AM to 4:00PM Pacific Standard Time).
E.T.I. Sound Systems, INC.
3383 Gage Ave., Huntington Park, CA, 90255

OFESSIO N A L

3383 Gage Avenue, Huntington Park, CA, 90255 Phone: 323-277-4100 Fax: 323-277-4108 National: 1-800-344-4ETI Internet: www.B-52PRO.com E-mail: info@B-52PRO.com
E.T.I. SOUND SYSTEMS, INC.

SMILE LICHT EN GELUID UTRECHT BV
Herenweg 64 - unit AR MAARSSEN tel. 0346-550531 fax. 0346-552820 info@smile-utrecht.nl www.smile-utrecht.nl
B-52 PRO BRUTO ADVIES PRIJSLIJST NEDERLANDSE MARKT FEBRUARI 2009
MODEL OMSCHRIJVING ADVIESPRIJS EXCL. 19% BTW MATRIX-SYSTEMS MATRIX-200 MATRIX-600 - NEW MATRIX-1000 V2 MATRIX-2000 M2C-SAT/PR. M6C-SAT/PR. M1KV2-SAT/PR. M2K- SAT/PR. SMARTKIT STORM-SERIES STORM-12A STORM-15A MX-SERIES MX-15 MX-MN15 MX-1515 MX-18S MX-15P MX-MN15P MX-1515P MX-18SP SL-SERIES SL-12 SL-15 SL-315 SL-1515 SL-18S ACT-SERIES ACT-18V2 (ACTIVE) ACT-18SV2 (PASSIVE) ACT-18XV2 (ACTIVE) ACT-18XSV2 (PASSIVE) ACT-15 ACT-15X ACT-1515 ACT-1515X Active 18" Subwoofer / 800-1200w Amplifier / B-52 18-220S - Tilt-Back Handle & Casters - Carpet 18" Passive Subwoofer / 1000w / B-52 18-220S - Tilt-Back Handle & Casters - Carpet Active 18" Subwoofer / 800-1200w Amplifier / B-52 18-220S - Paint 18" Passive Subwoofer / 1000w / 18-220S - Paint Active 15 Two-Way / 600w Amplifier / B-52 15-160 / Comp-4CLB / Carpet Active 15 Two-Way / 600w Amplifier / B-52 15-160 / Comp-4CLB / Paint Active Dual 15 Two-Way / 1000w Amplifier / 2 x B-52 15-160 / Comp-4CLB / Carpet Active Dual 15 Two-Way / 1000w Amplifier / 2 x B-52 15-160 / Comp-4CLB / Paint 1.308,00 723,00 1.308,00 723,00 1.248,00 1.248,00 1.457,00 1.457,00 12" Two-Way / Comp-4CLB / B-52 12-60 15" Two-Way / Comp-4CLB / B-52 15-Three-Way / B-52 8-50 Mid / Comp-4CLS / B-52 15-120 Dual 15" Two-Way / Comp-4CLB / 2 x B-52 15-120 / Casters & Tilt Back Handle Single 18" Direct-Radiating Subwoofer / B-52 18-180S / Casters & Tilt Back Handle 440,00 539,00 694,00 753,00 555,00 15" Two-Way / Comp-4MX / B-52 15-85 15" Two-Way Stage Monitor / Comp-4MX / B-52 15-85 Dual 15" Two-Way / Comp-4MX / 2 x B-52 15-85 / Casters & Tilt Back Handle Single 18" Direct-Radiating Subwoofer / B-52 18-180S 15" Two-Way / Comp-4MX / B-52 15-85 - PAINT FINISH 15" Two-Way Stage Monitor / Comp-4MX / B-52 15-85 - PAINT FINISH Dual 15" Two-Way / Comp-4MX / 2 x B-52 15-85 / Casters & Tilt Back Handle - PAINT FINISH Single 18" Direct-Radiating Subwoofer / B-52 18-180S - PAINT FINISH 287,00 287,00 416,00 396,00 386,00 386,00 555,00 515,00 NIEUW - Active - 12" Two-Way / ABS Plastic Cabinet / 400w Bi-Amp Design NIEUW - Active - 15" Two-Way / ABS Plastic Cabinet / 400w Bi-Amp Design 416,00 486,00 200w Three Piece Active System - 5-Ch Powered Mixer + 2 x Dual 6.5" Two-Way / With Suitcase 600w Three Piece Active System - 6-Ch Powered Mixer + 2 x 10" Three Way / With Three Covers 700w Three Piece Active System - 15" Subwoofer + 2 x 10" Two-way 1200w Three Piece Active System - 18" Subwoofer + 2 x 12" Two-way Dual 6.5" Two-Way Satellite Speakers / Pair 10" Three-Way Satellite Speakers / Flyable / Pair 10" Two-Way Satellite Speakers / Flyable / Pair 12" Two-Way Satellite Speakers / Flyable / Pair Includes: 2 x Speaker Stands, 2 x 25' Speaker Cables, 2 x XLR-XLR Cables, 1 x Carrying Bag 763,00 1.338,00 1.248,00 2.081,00 446,00 874,00 456,00 713,00 168,00
B-52 Pro adviesprijslijst feb 2009 - www.b-52.nl

OMSCHRIJVING

ADVIESPRIJS EXCL. 19% BTW
ARCHITECTURAL SERIES PA-212 PA-215 PA-315 PA-15X PA-1515X PA-18S PA-1818S PA-MN12 PA-MN15X LX-SERIES LX-18EV3 LX-18V3 LX-18AV3 (ACTIVE) LX-1515V3 Compact 18 Folded-Horn Subwoofer / B-52 18-220X 18 Folded-Horn Subwoofer / B-52 18-220X Active 18 Folded-Horn Subwoofer / 800-1200w Amplifier / B-52 18-220X NIEUW - Dual 15" Two-Way / Comp-4CLB / 2 x B-52 15-130 / Casters & Tilt Back Handle 684,00 832,00 1.635,00 832,00 12" Two-Way / Comp-4 / B-52 12-200 - Black 15" Two-Way / Comp-4 / B-52 15-200 - Black 15" Three-Way / Comp-4 / B-52 8-50 Mid / B-52 15-120 - Black 15 Two-Way / Comp-3300 (2) / B-52 15-200 / Bi-Amp Switch - Black Dual 15 Two-Way / Comp-3300 (2) / 2 x B-52 15-200 / Bi-Amp Switch - Black 18" Direct-Radiating Subwoofer / B-52 18-220S - Black Dual 18" Direct-Radiating Subwoofer / 2 x B-52 18-220S - Black 12" Two-Way Monitor / Comp-4CLS / B-52 12-200 - Black 15" Two-Way Monitor / Comp-3300 (2) / B-52 15-200 / Bi-Amp Switch - Black 783,00 842,00 892,00 1.288,00 1.724,00 832,00 1.486,00 832,00 1.338,00
PRODIGY / PRODIGY FX PRODIGY PRODIGY FX PRDG-CASE Dual CD/MP3 Player / 4 Channel VCA Mixer Dual CD/MP3 Player / DSP Effects / High-Res Jog Wheels / 4 Channel VCA Mixer / ATA Flight Case ATA Flight Case for PRODIGY 1.040,00 1.665,00 208,00