Barco Projectors

Configuration and Connections
SYSTEM 4xi xi PROJECTOR COMMUNICATIONS KIT

ATTENTION!

PLEASE READ THIS DOCUMENT FOR IMPORTANT INSTALLATION INSTRUCTIONS
THIS KIT HAS BEEN SHIPPED WITH THE FOLLOWING COMPONENTS:

Kit Type: BARCO

Included Communications Adapter(s):
Quantity 1 Part Number 26-309-01 Description Barco RCDVS Adapter
THE TABLE BELOW LISTS THE POSSIBLE CONFIGURATION(S) AND CORRESPONDING COMMUNICATIONS ADAPTER(S) FOR YOUR PROJECTOR MANUFACTURERS VARIOUS MODELS. PLEASE NOTE THAT YOUR SWITCHER HAS BEEN CONFIGURED AS INDICATED BY THE IN THE CONFIG AS COLUMN. IF YOUR PROJECTOR MODEL DIFFERS FROM THIS CONFIGURATION, YOU MUST RECONFIGURE YOUR SWITCHER WITH THE CORRECT SETTINGS. PLEASE REFER TO THE FOLLOWING PAGES FOR COMPLETE CONFIGURATION AND SIGNAL CONNECTION INSTRUCTIONS. THIS SWITCHER HAS BEEN CONFIGURED FOR:

Config as

RC5 PPM
Barco CRT Barco LCD Barco 5000 Barco 6300
Extron System 4xi Switcher Series Users Manual P/N 68-399-02 Rev. E

"

BARCO CRT
SW4 SW5 SW6 PROJ Comm CABLE Adapter J15 J15 J15 J26-309-01 26-309-01 26-309-01 26-309-01

off off off off

on on on on

8 A 9 C

Connecting System 4xi to Barco CRT/LCD Projector xi
If the System 4xi is already configured for a Barco CRT/LCD projector, go to step 4. If it is not set up correctly, it will be necessary to change switch settings on the System 4xi s Main Controller Board. Begin at Step 1 to verify the correct configuration. This procedure is for the Barco CRT projector as well as the 8100LC. 1. Use the Front Panel to display the Information Menu to verify that the System 4xi is already set up for the Barco projector. Apply power to the System 4xi and do the following: a. Press b. Press
[System 4NE model and software version displayed here]
to display the MENU SELECT on the LCD screen. or to step to Menu 8. to select this menu.
(See note.) (See note.) (See note.) (See note.) (Note: Information depends on System 4NE setup.)

c. Press

or to display the configuration. The example to the left is general, d. Press your display will show the System 4xi model name, the software version and the following information: PRJ = BARCO PRJ BAUD = 1200 UNIT No. = 000 HST BAUD = 9600 (value depends upon setup Menu 3)
2. Go to the procedure on page 2-3 of the System 4xi Users Manual to remove the System 4xi cover. Then go to page 2-4 and refer to the configurations below to set up the Main Controller board. Continue with Step 3 (below) when the configuration is correct.

Config as

SW2 on on on on

SW4 SW5 SW2

PRJ Comm CABLE Adapter J15 J15 J15 J15 26-309-01 26-309-01 26-309-01 26-309-01

Barco Barco Barco Barco

CRT LCD 5000 6300

SW2 J15

Barco CRT Configuration

SW4 SW3 SW5

Barco LCD (except model 5000)

SW4 SW5

Barco 5000 Configuration

Barco 6300 Configuration

Page 1
3. Double-check your work and be sure the System 4xi cover is on securely. 4. Install the System 4xi in its place of operation (i.e. rack), but not powered on.
__________ Changes in some switch configurations are not detected until the power is removed at the AC cord, and then restored.
Refer to the following connection diagrams and continue. Use the Barco Comm Adapter provided by Extron (BR COM 26-309-01). 5. The Barco Comm Adapter has a cable with a 9-pin female connector. Plug this into the male Comm Port connector on the rear of the projector. 6. Plug the HD 15-pin connector of the Projector Communications Extension cable (shown as CC 50'/100') into the PJ Comm port on the System 4xi. The other end has a 9-pin female connector. Plug this into the male connector on the BR COM Adapter case.

______ Secure all of the connector screws.
7. Plug the (4 or 5) BNC connectors from one end of the (user-supplied) RGBS/HV cable onto the System 4xi output and those on the other end onto the BNC connectors on the rear of the projector (marked RGsB/RGBS/RGBHV).
System 4xi Series Barco CRT Projector Connections xi
Use the following illustrations as a guide when connecting the System 4xi to a Barco CRT projector. Refer to Barco documentation to continue the installation.
RGsB/RGBS Comp/H-Sync V-Sync Port 1 Video Projector Mode Green: Operation Red: Standby Port 1 S-Video Power/Mains

R Comm Port Port 3

Female

Yellow

RGsB/RGBS/RGBHV

BR COM Adapter 26-309-01

9-Pin Female

CC 50'/100' 25-305-01/02

Male 15-Pin

V R G B

Barco CRT Connections ____________ In a rack mount, do NOT allow the weight of the cables to be supported by the System 4xi. See page 2-5 for cabling guidelines. Extron System 4xi Switcher Series Users Manual P/N 68-399-02 Rev. E Page 2
System 4xi Series Barco LCD Projector Connections xi
Use the following illustrations as a guide when connecting the System 4xi to a Barco LCD projector. Refer to Barco documentation to continue the installation.
Br Com Adapter 26-309-01 9-Pin Female 3, 4 or 5 BNC

15-Pin Male

INPUT 1 INPUT 2 INPUT 3 INPUT 4 OUTPUT

PJ COMM

RS 232

Barco LCD Connections

____________ In a rack mount, do NOT allow the weight of the cables to be supported by the System 4xi. See page 2-5 for cabling guidelines.

Page 3

System 4xi Series Barco 6300 Projector Connections xi
Use the following illustrations as a guide when connecting the System 4xi to a Barco 6300 projector. Refer to Barco documentation to continue the installation.

Br Com Adapter 26-309-01

3, 4 or 5 BNC

Barco 6300 Connections

Page 4