TABLE OF CONTENTS

1. Safety Instruction

2. Technical Specification
I IM STAGE PAINTER 12 L E Preliminary User Guide R P
Official version will follow soon on: WWW.BRITEQ-LIGHTING.COM

3. How To Set The Unit

4. How To Control The Unit

5. Troubleshooting

6. Fixture Cleaning
Please read carefully the instruction, which includes important WARNING information about the installation, usage and maintenance.
Caution There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact your nearest dealer.
Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that they also receive this instruction booklet. Unpack and check carefully there is no transportation damage before using the unit. Before operating, ensure that the voltage and frequency of power supply match the power requirements of the unit. Its important to ground the yellow/green conductor to earth in order to avoid electric shock. The unit is for indoor use only. Use only in a dry location. The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent surfaces. Be sure that no ventilation slots are blocked. Disconnect main power before replacement or servicing. Make sure there is no flammable materials close to the unit while operating as it is fire hazard. Use safety cable when fixes this unit. Maximum ambient temperature is TA: 40. Dont operate it where the temperature is higher than this. In the event of serious operating problem, stop using the unit immediately. Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to damage or use the same type spare parts.

Installation

The unit should be mounted via its metal hole on the bracket. Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating. Always ensure that the structure to which you are attaching the unit is secure and is able to support a 10 times weight of the unit.
malfunction. Please contact the nearest authorized technical assistance center. Always Do not touch any wire during operation as high voltage might be causing electric shock.

Warning

For power supply, do not connect in series much more than 10 units, use another mains supply for next 10 units. To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture. Do not open the unit within five minutes after switching off. The housing, the lenses must be replaced if they are visibly damaged. 2-

3/6/9/12/15 channels switchable
Automatically switching between music trig and auto mode Great built-in programs under Master/Slave mode trigged by music Individual control of each LED cluster Sound sensitivity adjustable via the menu Auto-fading show with 3 different speeds Specially designed stand for floor operation LCD display for easy addressing and setting VoltageAC 100-240V~50/ 60Hz Power consumption: 40W LED: 12 x 3W Tri-Color Beam Angle:D30, D45, D60, D40x70 Fuse: T 6.3A Dimension: 387 x 207 x 95 mm Weight: 3.9 kgs
3. How To Set The Unit 3.1 Control Panel

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is showing on the display. Select the function by ENTER button and the display will blink. Use DOWN and UP button to change the mode. Once the required mode has been selected, Press ENTER button to store. Back to the main functions without any change press the MENU button or wait for 1 minute. Hold MENU button to exit menu mode, the
Display To show the various menus and the selected functions LED DMX MASTER SLAVE SOUND Button MENU DOWN UP ENTER Microphone Receive the sound to control the unit Only for remote control function. Mains input Connect to supply mains power. Mains output Fuse To select the programming functions To go backward in the selected functions To go forward in the selected functions To confirm the selected functions On On On Flashing DMX input present Master Mode Slave Mode Sound activation

unit will run the built-in program you
selected At this time you can press UP and DOWN button to change show, the new show will effect immediately. If you change to show 1-8 or Auto Fade, you can press ENTER button to choose speed. The unit
By connect to the 1/4 microphone jack to control the unit for Stand by, Function and Mode
Connect to supply mains power for other units. For over current protection. DMX input/output
For DMX512 link, use 3/5-pin XLR plug cable to link the unit together.
the music. drawing: mode).
will run in the speed selected or it will run to
The main functions are shown on the
DMX Address DMX Address is showing on the display.
Press the MENU button up to when the Press ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press the ENTER button to store. Back to the main functions without any change press the MENU button (or wait for 1 minute to exit menu Channel Mode Press the MENU button up to when the Channel Mode is showing on the display. Press ENTER button and the display will blink. Use DOWN and UP button to select 5-
Safety Ring Keep the installation safe.
the 3 channels mode or 6 channels mode or 9 channels mode or 12 channels mode 15 channels mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button (or wait for 1 minute to exit menu mode). Show Mode Press the MENU button up to when the Show Mode is showing on the display. Press ENTER button, the display will blink. Press DOWN and UP button to select Show 0 (Auto show), Show 1 or or Show 8 or Auto Fade, once selected, press MENU button to store and back to the last menu, then the unit will run to music. If you choose Show 1-8 or Auto Fade, press the ENTER button to confirm, then you can press DOWN and UP button to select Speed 1 (slow speed) or Speed 2 (middle speed) or Speed 3 (fast speed), press ENTER button to store, the unit will run in the speed that selected. Back to the main functions without any change press the MENU button or wait for 8 seconds. Color Mode Press the MENU button up to when the Color Mode is showing on the display. Press ENTER button, the display will blink. Press DOWN and UP button to select Manu (manual setting), Color 1 or or Color 32, once selected, press MENU button to store. If you choose Maun, press the ENTER button to confirm, you can press DOWN and UP button to

sensitively (1-100) of the unit. Once the value has been selected, press the ENTER button to store. Back to the main functions without any change press the MENU button (or wait for 1 minute to exit menu mode). Black Out Press the MENU button up to when the Black Out is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the yes (yes blackout) or no (no blackout) mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button (or wait for 1 minute to exit menu mode). Back Light
Press the MENU button up to when the Back Light is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select the on (back light on) or off (back light off 1 minute after auto show) mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU
select Red or Green or Blue, press ENTER button to confirm and press DOWN and UP without any change press the MENU button or wait for 8 seconds. Slave Mode
button to adjust the value, then press ENTER button to store. Back to the main functions
Press the MENU button up to when the Slave Mode is showing on the display. Press ENTER button and the display will blink. Use DOWN and UP button to select the slave 1 or without any change press the MENU button (or wait for 1 minute to exit menu mode). Sound State Press the MENU button up to when the Sound State is showing on the display. Press
slave 2 mode. Once selected, press the ENTER button to store. Back to the main functions
ENTER button and the display will blink. Use DOWN and UP button to select the on (sound control on) or off (sound control off) mode. Once selected, press the ENTER button to store. Back to the main functions without any change press the MENU button (or wait for 1 minute to exit menu mode). Sound Sense

Auto Test Manual Test

button (or wait for 1 minute to exit menu mode). Press the MENU button up to when the Auto Test is showing on the display. Pressing ENTER button and the display will show Test and the unit will run self-test by built-in program. To go back to the functions press the MENU button. Press the MENU button up to when the Manual Test is showing on the display. Press ENTER button and Red 1 will blink, use UP and DOWN button to choose Green 1 or Blue 1 or Red2 or or Blue 4 or Dimmer or Strobe, press ENTER button to enter, then press UP and Down button to adjust the value and press ENTER button to choose next optional. Back to the main functions without any change please press the MENU button. White Balance Press the MENU button up to when the White Balance is showing on the display. Press ENTER button and the r 255 will blink, press UP and Down button to adjust the value, press ENTER button to store and g 255 will blink on the display, press UP and Down button to adjust the value, press ENTER button to store and b 255 will blink on the display, press UP and Down button to adjust the value, and press ENTER button to store. Back to the main functions without any change please press the MENU button. Fan Speed Press the MENU button up to when the Fan Speed is showing on the display. Pressing ENTER button and the display will blink. Use DOWN and UP button to select Auto Speed 7-

Press the MENU button up to when the Sound Sense is showing on the display. Press ENTER button and the display will blink. Use DOWN and UP button to adjust the sound
(When the temperature of the unit under 40, FAN stops; between 45~55, FAN runs at half speed; above 60, FAN runs at full speed. The LEDs will be off if the temperature higher than 75) or High Speed, press ENTER button to store. To go back to the functions press the MENU button. Fixture Temp Press the MENU button up to when the Fixture Temp is blinking on the display. Pressing ENTER button and the display will show the temperature of the unit. To go back to the functions press the MENU button. Fixture Time Press the MENU button up to when the Fixture Time is blinking on the display. Pressing ENTER button and the display will show the number of working hours of the unit. To go back to the functions press the MENU button. Firmware Version Press the MENU button up to when the Firmware Version is blinking on the display. Pressing ENTER button and the display will show the version of software of the unit. To go back to the functions press the MENU button.

4.2 Easy Controller

The easy remote control is used only in master/slave mode. By connecting to the 1/4 microphone jack of the first unit, you will find that the remote controller on the first unit will control all the other units for Stand by, Function and Mode selection Stand By Function Blackout the unit 1. Sync. Strobe 2. Async strobe 3. Sound Strobe

Select

Manua Color or color 1-32

Sound (LED OFF)

You can operate the unit in three ways: 1. By master/slave built-in preprogram function 2. By easy controller 3. By universal DMX controller
4.1 Master/Slave Built In Preprogrammed Function
By linking the units in master/slave connection, the first unit will control the other units to give an automatic, sound activated, synchronized light show. This function is good when you want an instant show.

2-light show

In slave mode, slave 1 means the unit run as the master unit and slave 2 means 2-light show. In order to create a great light show, you can set slave 2 on the second unit to get contrast movement to each other, even if you have two units only.

4.3 DMX Controller

Use universal DMX controller to control the units, you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal. Press the MENU button up to when the DMX Address is showing on the display. Press ENTER button and the display will blink. Use DOWN and UP button to change the DMX512 address. Once the address has been selected, press and keep ENTER button to store. To go back to the functions without any change press the MENU button or wait for 1 minute to exit menu mode. Please refer to the following diagram to address your DMX512 channel for the first 4 units:

Unit 1 1

LED On

Select show 1-8

or Auto fade
Select Speed 1. Slow 3. Fast Fast blinking 2. middle

Slow blinking

Channel Mode 3 channels 6 channels 9 channels 12 channels 15 channels

Unit 13 16

Unit 25 31

Unit 37 46

4.4 DMX 512 Configuration

Front View:

DMX Configuration:

4.5 DMX512 Connection

1. If you using a controller with 5 pins DMX output, you need to use a 5 to 3 pin

adapter-cable.

2. At last unit, the DMX cable has to be terminated with a terminator. Solder a 120 ohm 1/4W resistor between pin 2(DMX-) and pin 3(DMX+) into a 3-pin XLR-plug and plug it in the DMX-output of the last unit. unit to the input of the next unit. The cable can not branched or split to a `Y` cable. DMX 512 is a very high-speed signal. Inadequate or damaged cables, soldered joints or corroded connectors can easily distort the signal and shut down the system. 4. The DMX output and input connectors are pass-through to maintain the DMX circuit, when power is disconnected to the unit. 5. Each lighting unit needs to have an address set to receive the data sent by the controller. The address number is between 0-511 (usually 0 & 1 are equal to 1). 6. The end of the DMX 512 system should be terminated to reduce signal errors. 7. 3 pin XLR connectors are more popular than 5 pin XLR. 3 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) 5 pin XLR: Pin 1: GND, Pin 2: Negative signal (-), Pin 3: Positive signal (+) Pin 4/5: Not used.
3. Connect the unit together in a `daisy chain` by XLR plug from the output of the
Following are a few common problems that may occur during operation. Here are some suggestions for easy troubleshooting: A. The unit does not work, no light and the fan does not work 1. Check the connection of power and main fuse. 2. Measure the mains voltage on the main connector. 3. Check the power on LED.
The cleaning of internal and external optical lenses and/or mirrors must be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates: damp, smoky or particularly dirty surrounding can cause greater accumulation of dirt on the units optics. Clean with soft cloth using normal glass cleaning fluid. Always dry the parts carefully. every 30/60 days.

Clean the external optics at least every 20 days. Clean the internal optics at least
B. Not responding to DMX controller 1. DMX LED should be on. If not, check DMX connectors, cables to see if link properly. 2. If the DMX LED is on and no response to the channel, check the address settings and DMX polarity. 3. If you have intermittent DMX signal problems, check the pins on connectors or on PCB of the unit or the previous one. 4. Try to use another DMX controller. 5. Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit.
C. Some units dont respond to the easy controller 1. You may have a break in the DMX cabling.
2. Check the LED for the response of the master/ slave mode signal.
D. No response to the sound
1. Make sure the unit does not receive DMX signal. 2. Check if the sound sensitively is too low.
E. One of the channels is not working well
1. The cable connected to the PCB may broken.
We declare that our products (lighting equipments) comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility (EMC) Directive 89/336/EEC. EN55103-1:199601-2; EN55103-2:1996; EN61000-3-2:2000+A2:2005; EN61000-3-3:1995+A1:2001+A2:2005. & Harmonized Standard EN 60598-1: 2004 IEC 60598-1:2003+ corrigendum 2004 Part 1:General requirements and test
EC Declaration of Conformity
Following the provisions of the low voltage directive 73/23/EEC and 93/68/EEC