Reviews & Opinions
Independent and trusted. Read before buy Behringer PMP3000!

Behringer PMP3000


Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Behringer PMP3000, size: 3.9 MB
Related manuals
Behringer PMP3000 Effect Presets
Behringer PMP3000 Front Panel

Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.


Behringer PMP3000Behringer PMP3000 1,200-Watt 16-CH Powered Mixer w/Multi-FX Processor
A seven-band graphic EQ section provides final frequency contouring of audio at the main output. Behringer's FBQ feedback detection system reveals problem frequency bands that may cause feedback and allows users to adjust them. The PMP3000 is a lightweight, portable mixing solution for musicians, and presenters on-the-go. Dual 400 Watt Power Amplifier Internal 400 x 400 watt power amplifier will drive loud speakers directly from the unit. 16 Total Input Channels The PMP3000 features eight mo... Read more

Part Number: PMP3000
UPC: 04033653021005, 4 033653 021005, 4033653021005


[ Report abuse or wrong photo | Share your Behringer PMP3000 photo ]

Video review

Lamb of God Redneck DRUM COVER by 0bz3n


User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.




User Manual

500/1,200-Watt 12, 16 and 20-Channel PoweredMixer with Multi/Dual Multi-FX Processor and FBQ FeedbackDetectionSystem
EUROPOWER PMP1000/PMP3000/PMP5000 User Manual

Table of Contents

Important Safety Instructions.. 3 Legal Disclaimer.. 3 Limited Warranty.. 3 1. Introduction... 5 1.1 Before you get started.. 5 1.1.1 Shipment... 5 1.1.2 Initial operation.. 5 1.1.3 Online registration... 5 1.2 The manual... 5 2. Control Elements... 5 2.1 Mono and stereo channels.. 5 2.1.1 Input section... 6 2.2 Equalizer and FBQ... 7 2.3 Effects section... 7 2.4 Main and monitor section.. 8 2.4.1 Connectors... 8 2.5 Rear panel... 9 3. Digital Effects Processor.. 9 4. Installation... 9 4.1 Mains connection... 9 4.2 Audio connections.. 9 4.3 Loudspeaker connections... 11 5. Wiring Examples.. 12 6. Specifications.. 15
Important Safety Instructions
Terminals marked with this symbol carry electrical current of sufficient magnitude to constitute risk of electric shock. Use only high-quality commercially-available speaker cables with 1/4" TS plugs pre-installed. All other installation or modification should be performed only by qualified personnel. This symbol, wherever it appears, alerts you to the presence of uninsulated dangerous voltage inside the enclosure - voltage that may be sufficient to constitute a risk of shock. This symbol, wherever it appears, alerts you to important operating and maintenance instructions in the accompanying literature. Please read the manual. Caution To reduce the risk of electric shock, do not remove the top cover (or the rear section). No user serviceable parts inside. Refer servicing to qualified personnel. Caution To reduce the risk of fire or electric shock, do not expose this appliance to rain and moisture. The apparatus shall not be exposed to dripping or splashing liquids and no objects filled with liquids, such as vases, shall be placed on the apparatus. Caution These service instructions are for use by qualified service personnel only. To reduce the risk of electric shock do not perform any servicing other than that contained in the operation instructions. Repairs have to be performed by qualified service personnel. 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. Use only attachments/accessories specified by the manufacturer. 12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13. Unplug this apparatus during lightning storms or when unused for long periods of time. 14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. The apparatus shall be connected to a MAINS socket outlet with a protective earthing connection. 16. Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

Limited Warranty

1 Warranty
(1) This limited warranty is valid only if you purchased the product from a BEHRINGER authorized dealer in the country of purchase. A list of authorized dealers can be found on BEHRINGERs website under Where to Buy, or you can contact the BEHRINGER office closest to you. (2) MUSIC Group* warrants the mechanical and electronic components of this product to be free of defects in material and workmanship if used under normal operating conditions for a period of one (1) year from the original date of purchase (see the Limited Warranty terms in 4 below), unless a longer minimum warranty period is mandated by applicable local laws. If the product shows any defects within the specified warranty period and that defect is not excluded under 4, MUSIC Group shall, at its discretion, either replace or repair the product using suitable new or reconditioned product or parts. In case MUSIC Group decides to replace the entire product, this limited warranty shall apply to the replacement product for the remaining initial warranty period, i.e., one (1) year (or otherwise applicable minimum warranty period) from the date of purchase of the original product. (3) Upon validation of the warranty claim, the repaired or replacement product will be returned to the user freight prepaid by MUSIC Group. (4) Warranty claims other than those indicated above are expressly excluded. PLEASE RETAIN YOUR SALES RECEIPT. IT IS YOUR PROOF OF PURCHASE COVERING YOUR LIMITED WARRANTY. THIS LIMITED WARRANTY IS VOID WITHOUT SUCH PROOF OF PURCHASE.
2 Online registration Please do remember to register your new BEHRINGER equipment right after your purchase at under Support and kindly read the terms and conditions of our limited warranty carefully. Registering your purchase and equipment with us helps us process your repair claims quicker and more efficiently. Thank you for your cooperation! 3 Return materials authorization
(1) To obtain warranty service, please contact the retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may contact the BEHRINGER distributor for your country listed under Support at If your country is not listed, please check if your problem can be dealt with by our Online Support which may also be found under Support at Alternatively, please submit an online warranty claim at BEFORE returning the product. All inquiries must be accompanied by a description of the problem and the serial number of the product. After verifying the products warranty eligibility with the original sales receipt, MUSIC Group will then issue a Return Materials Authorization (RMA) number.

Legal Disclaimer

Technical specifications and appearance are subject to change without notice. The information contained herein is correct at the time of printing. All trademarks are the property of their respective owners. MUSIC Group accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph or statement contained herein. Colors and specifications may vary slightly from product. BEHRINGER products are sold through authorized dealers only. Distributors and dealers are not agents of MUSIC Group and have absolutely no authority to bind MUSIC Group by any express or implied undertaking or representation. This manual is copyrighted. No part of this manual may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any purpose, without the express written permission of Red Chip Company Ltd. ALL RIGHTS RESERVED. 2010 Red Chip Company Ltd. Trident Chambers, Wickhams Cay, P.O. Box 146, Road Town, Tortola, British Virgin Islands
(2) Subsequently, the product must be returned in its original shipping carton, together with the return authorization number to the address indicated by MUSIC Group. (3) Shipments without freight prepaid will not be accepted.
4 Warranty Exclusions (1) This limited warranty does not cover consumable parts including, but not limited to, fuses and batteries. Where applicable, MUSIC Group warrants the valves or meters contained in the product to be free from defects in material and workmanship for a period of ninety (90) days from date of purchase. (2) This limited warranty does not cover the product if it has been electronically or mechanically modified in any way. If the product needs to be modified or adapted in order to comply with applicable technical or safety standards on a national or local level, in any country which is not the country for which the product was originally developed and manufactured, this modification/adaptation shall not be considered a defect in materials or workmanship. This limited warranty does not cover any such modification/adaptation, regardless of whether it was carried out properly or not. Under the terms of this limited warranty, MUSIC Group shall not be held responsible for any cost resulting from such a modification/adaptation. (3) This limited warranty covers only the product hardware. It does not cover technical assistance for hardware or software usage and it does not cover any software products whether or not contained in the product. Any such software is provided AS IS unless expressly provided for in any enclosed software limited warranty. (4) This limited warranty is invalid if the factoryapplied serial number has been altered or removed from the product. (5) Free inspections and maintenance/repair work are expressly excluded from this limited warranty, in particular, if caused by improper handling of the product by the user. This also applies to defects caused by normal wear and tear, in particular, of faders, crossfaders, potentiometers, keys/buttons, guitar strings, illuminants and similar parts. (6) Damage/defects caused by the following conditions are not covered by this limited warranty: improper handling, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals; connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used; damage/defects caused by acts of God/Nature (accident, fire, flood, etc) or any other condition that is beyond the control of MUSIC Group.

(7) Any repair or opening of the unit carried out by unauthorized personnel (user included) will void the limited warranty. (8) If an inspection of the product by MUSIC Group shows that the defect in question is not covered by the limited warranty, the inspection costs are payable by the customer. (9) Products which do not meet the terms of this limited warranty will be repaired exclusively at the buyers expense. MUSIC Group or its authorized service center will inform the buyer of any such circumstance. If the buyer fails to submit a written repair order within 6 weeks after notification, MUSIC Group will return the unit C.O.D. with a separate invoice for freight and packing. Such costs will also be invoiced separately when the buyer has sent in a written repair order. (10) Authorized BEHRINGER dealers do not sell new products directly in online auctions. Purchases made through an online auction are on a buyer beware basis. Online auction confirmations or sales receipts are not accepted for warranty verification and MUSIC Group will not repair or replace any product purchased through an online auction.

9 Amendment

Warranty service conditions are subject to change without notice. For the latest warranty terms and conditions and additional information regarding MUSIC Groups limited warranty, please see complete details online at
* MUSIC Group Macao Commercial Offshore Limited of Rue de Pequim No. 202-A, Macau Finance Centre 9/J, Macau, including all MUSIC Group companies
5 Warranty transferability This limited warranty is extended exclusively to the original buyer (customer of authorized retail dealer) and is not transferable to anyone who may subsequently purchase this product. No other person (retail dealer, etc.) shall be entitled to give any warranty promise on behalf of MUSIC Group. 6 Claim for damage
Subject only to the operation of mandatory applicable local laws, MUSIC Group shall have no liability to the buyer under this warranty for any consequential or indirect loss or damage of any kind. In no event shall the liability of MUSIC Group under this limited warranty exceed the invoiced value of the product.
7 Limitation of liability This limited warranty is the complete and exclusive warranty between you and MUSIC Group. It supersedes all other written or oral communications related to this product. MUSIC Group provides no other warranties for this product. 8 Other warranty rights and national law (1) This limited warranty does not exclude or limit the buyers statutory rights as a consumer in any way. (2) The limited warranty regulations mentioned herein are applicable unless they constitute an infringement of applicable mandatory local laws. (3) This warranty does not detract from the sellers obligations in regard to any lack of conformity of the product and any hidden defect.

1.1 Before you get started
1.1.1 Shipment Your PMP was carefully packed at the factory and the packaging is designed to protect the unit from rough handling. Nevertheless, we recommend that you carefully examine the packaging and its contents for any signs of physical damage which may have occurred during transit.
If the unit is damaged, please do NOT return it to BEHRINGER,

1.2 The manual

This manual is designed to give you both an overview of all control elements and to provide details about how to use them. To provide you with a clear structure, we have grouped the control elements according to their function. They can easily be found on the enclosed numbered illustrations. If you need more detailed information on specific topics, please visit our web site at
butnotify your dealer and the shipping company immediately. Otherwise,claimsfor damage or replacement may not be granted.
We recommend that you use a flight case, so as to give your power

2. Control Elements

A detailed description of all functions of your power mixer can be found in the following chapters. Please also refer to the enclosed sheet with the numbered illustrations to get a good overview of the control layout.
mixer optimum protection during use or transport.
Always use the original packing carton to prevent damage during

storage or transport.

Make sure that children cannot play unsupervised with the device or
2.1 Mono and stereo channels
(1) Use the TRIM control to adjust the input gain. Be sure to set this control fully counter-clockwise before you connect or disconnect a signal source to an input. TRIM controls both the microphone and the LINE input. Theblack scale shows the microphone gain (+10 to +60 dB on channels with XENYX MIC PREAMPS and 0 to +40 dB on conventional microphone inputs; PMP1000only, channels 5/6 and 7/8).
The LINE scale indicates the sensitivity of the LINE input, ranging from +10to -40 dBu. PMP1000: The mono/stereo combination channels 5/6 and 7/8 have a sensitivity of +20 to -20 dBu.


Please ensure proper disposal of all packing materials.
1.1.2 Initial operation Be sure that there is enough air space around the unit for cooling and, to avoid overheating, please do not place the EUROPOWER near radiators, etc.
Blown fuses must be replaced by fuses of the same type and rating!
Please refer to the Specifications for details. The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements.
Please make sure that all units have a proper ground connection.
(2) The LEVEL SET LED illuminates when an optimum operating level has beenadjusted. (3) The mono channels are equipped with a high-slope LOW CUT filter eliminating unwanted low-frequency signals like rumble noise. (4) PMP3000/PMP5000 (stereo channels): Press the A/B button to switch from 1/4" jacks to RCA connectors, and vice versa. Position A = 1/4" jacks; positionB = RCA connectors. (5) The HIGH control in the EQ section governs the high frequency range of the respective channel.

Foryour own safety, never remove or disable the ground conductor from the unit or on the AC power cord. To avoid damage on the device, do not
earth the loudspeaker outputs connect the loudspeaker outputs to each other connect the loudspeaker outputs to those of other amplifiers
(6) Use the MID control to boost or cut the midrange frequencies. (7) PMP5000: The PMP5000 has an additional semi-parametric filter for the midrange frequencies in the mono channels (tunable from 100 Hz to 8 kHz). Adjust the boost/cut with the MID control, and the frequency with the FREQcontrol.
The stereo channels contain a stereo EQ section. The cut-off frequencies of the high and low bands are 12 kHz and 80 Hz respectively, while the center frequencies of the high-mid and low-mid bands are 3 kHz and 400Hzrespectively.
(19) Each mono input features one LINE IN connector (1/4" jack), which can be used with either balanced or unbalanced signals.
Please remember to use either the microphone or the line input on a
specific channel. Never use both at the same time!
When you connect a mono line signal to a stereo channel, alwaysuse
the left input. The mono signal will then be reproduced by both sidesequally.
PMP1000: This does not apply to the mono/stereo combination
(8) The LOW control allows you to boost/cut the low frequency range. (9) With the MON(ITOR) control you can adjust the volume of each channel in the monitor mix. (10) The PMP3000 and PMP5000 feature a second MON control (MON 2) for the volume of the second monitor bus. (11) The FX control determines the signal level sent from each channel to the built-in effects processor; this signal is also present at the FX SEND jack (see (64) ). (12) The PMP5000 has two FX controls (FX 1 and FX 2), so that you can use two effects simultaneously. Accordingly, the PMP5000 also has two effect aux buses, which have one output jack in common (see (46) and (64) ).
Please note that the effects processor signal will be inaudible,

channels 5/6 and 7/8.

(20) INSERT I/O. Insert points or simply inserts are used to process a signal with dynamic processors or equalizers. They are pre-fader, pre-EQ and pre-MON/FX SEND. Unlike reverb and other effects, which are usually added to the dry signal, dynamic processors usually process the entire signal. So,aux send buses are not the best solution. Dynamic processors need to be inserted directly into the signal path. Once processed, the signal then returns to the mixing console at the same point where it left. Signal interruption takes place only if a plug is inserted into the corresponding jack (1/4" stereo plug: tip = signal output, ring = input). All mono input channels are equipped with inserts. (21) The stereo channels have a TRIM control for gain adjustment, with the input sensitivity ranging from +20 to -20 dB.

2.4 Main and monitor section
andtransparent. The surround control determines the effect intensity. This is a built-in effect, which widens the stereo panorama, thus making the sound more lively
(55) Use the CD/TAPE INPUT jacks (RCA) to connect an external stereo signal, such as a CD player, tape deck or other line-level sources. (56)
The VOICE CANCELLER filters vocal-specific frequencies from the CD/TAPE INPUT signal. This function can be used for karaoke, i.e. you can remove the vocals from a song and then sing along with the music yourself.
(44) Press the XPQ TO MAIN switch to activate this effect. (45) Pressing the AFL switch (after-fader listening) activates the solo function. If AFL is on for the corresponding channel in the main section, you will only hear the signal from this channel. Its volume can be adjusted with the fader. Switching AFL on has no effect on the main or monitor mix, as long as you dont move the fader. In this way, you can monitor one or several selected signals via the PHONES/CTRL jack (65). When AFL is on, the corresponding control LED illuminates.
The PMP1000 does not have an AFL function.
(57) The CD/TAPE OUTPUT provides the line level stereo signal (e.g. for a DATrecorder).
If the CD/TAPE OUT signal is connected to a recording machine whose
output signal is returned to the CD/TAPE IN, feedback can occur when you activate the record function on the recording machine. So,disconnect the CD/TAPE IN from the recording machine before you start recording or set the CD/TAPE input signal to zero!
(46) PMP1000: FX SEND fader.
PMP3000: FX fader. PMP5000: FX 1/2 fader. This is the master send fader for the signal routed to the effects processor and to the FX SEND output (63) (see also (11) and (12) ).
(58) PMP1000: The MAIN OUT jacks allow you to send the main line level signal to an external amplifier, when, for example, you want to use the mixer and effects section. The PMP3000 and PMP5000 have two separately controllable line level MAIN outputs (59) (MAIN 1/2). (59) Connect your monitor power amps or active monitor speakers to the MON1/2 SEND to monitor the signal mix created with the MON controls or to route it to the musicians on stage. (60) The PMP Series comes with a POWER AMP INSERT connection that is provided for various applications. This connection enables you to use the power amplifier of the device to amplify the output signal of another preamp. For example, it is possible to connect a larger mixer or preamp output (line signal) of an instrument amplifier. In this case, you only need an unbalanced, mono jack cable.
Furthermore, it is possible to use the POWER AMP INSERT as a conventional insert to add a compressor or graphic equalizer to the signal path, forinstance. Here, a balanced, stereo jack cable is required and the assignment of tip and ring needs to be observed according to Figure4.5 (see Chapter 4.2 Audio Connections). In this case, the ring is the so-called Send, which is connected to the input of the additional device, andthe tip is referred to as Return, which is connected to the output of the additionaldevice. Lastly, it is possible to tap the output signal of the devices mixer section from the POWER AMP INSERT in order to use a second, external power amp. A balanced, stereo jack cable is required with the ring (not the tip) connectedto the input of the external power amp. If you want to use the internal and external power amps at the same time, just wire the connectors ring and tiptogether.

(47) PMP1000: MON SEND fader.
PMP3000/PMP5000: MON 1/2 fader. These faders are used to set the monitor output volume (see also (9) and(10) ).
(48) PMP1000: The main mix allows you to control the volume from the Main 1 output with both faders.
PMP3000/PMP5000: The MAIN 1 fader controls the volume of the EUROPOWER. The main signal is also provided at the MAIN 1 output (see also (58) ).
(49) PMP3000/PMP5000: The MONO fader controls the mono mix signal (see also (63) ). (50) PMP5000: The SUB FILTER filters out frequencies above the selected setting, so that only low frequencies are sent to an (active) subwoofer via the MONOOUT (63) ). Set this switch to On to activate the filter. (51) PMP5000: The SUB FREQ control determines the cut-off frequency for the subwoofer output. This value can be adjusted from 30 to 200 Hz. (52) The PHONS/CTRL R control adjusts the headphone or control room volume (see also (65) ). (53) PMP3000/PMP5000: The MAIN 2 control determines the volume at the MAIN 2 output (see also (59) ), which is the same signal as at MAIN 1, but with extra output jacks and separate volume control.
(61) The FOOTSWITCH jack is for a standard footswitch. You can activate an effect bypass, thereby muting the effects processor. Use a dual foot switch for the PMP5000, so that you can enable/disable FX 1 and FX 2 independently of each other. In this case, the tip of the 1/4" plug controls FX1, and the ringFX 2.
(62) PMP3000/PMP5000: The MONO OUT is for connecting a subwoofer. ThePMP5000 has the additional possibility of setting the low-frequency range for the subwoofer.
Use the SUB FILTER control (50) to adjust the frequency.
3. Digital Effects Processor
24-BIT MULTI-EFFECTS PROCESSOR This built-in effects module produces high-grade standard effects such as reverb, chorus, flanger, delay and various combination effects. The integrated effects module has the advantage of requiring no wiring. This way, the danger of creating ground loops or uneven signal levels is eliminated at the outset, completely simplifying the handling. These effect presets are designed to be added to dry signals.
Turn down the FX controls in those channel strips whose signals you
(63) The FX SEND connector can be used to route the FX SEND signal from the input channel, for example, to the input of an external effects device. Sincethe PMP5000 has two FX controls per input signal (see (12) ), both FX SEND 1+2 are present at one jack.

Please note: The SEND signal is in parallel with the FX SEND jacks and
with the effects processor, so that both can be controlled together by one control.
For the FX signals, use a 1/4" stereo plug connected as follows: FX 1 = tip;

dont wish to process.

FX 2 = ring

4. Installation

4.1 Mains connection
The mains connection is made using the enclosed power cord and a standard IEC receptacle. It meets all of the international safety certification requirements. Blown fuses must be replaced by fuses of the same type and rating.
(64) The PHONS/CTRL connector allows you to connect a pair of stereo headphones or an (active) monitor speaker.

2.5 Rear panel

(65) The mains connection is via a standard IEC receptacle. An appropriate power cord is supplied with the unit. (66) FUSE HOLDER. Before connecting the unit to the mains, ensure that the voltage setting matches your local voltage. Blown fuses should only be replaced by fuses of the same type and rating. Please also read the information given in the Specifications. (67) Use the POWER switch to put your PMP into operation. The POWER switch should always be in the Off position before connecting your unit to themains.
Please note: The POWER switch does not fully disconnect the unit from
Foryour own safety, never remove or disable the ground conductor from the unit or of the AC power cord.

4.2 Audio connections

The inputs and outputs of your BEHRINGER EUROPOWER are unbalanced 1/4" mono jacksexcept for the mono channel line inputs, which are balanced 1/4" stereo jacks. Of course, all inputs and outputs work with both balanced and unbalanced connectors. The tape in and outputs are on RCA connectors.
Please ensure that only qualified personnel install and operate the
the mains. Unplug the power cord completely when the unit is not used for prolonged periods of time.
(68) SERIAL NUMBER. (69) This is where you find the cooling fan of the unit.
The PMP5000 has two cooling fans.
PMP. During installation and operation, the user must have sufficient electrical contact to earth. Electrostatic charges might affect the operation of the unit.
Unbalanced " TS connector
Strain relief clamp Sleeve Tip
(70) OUTPUT A (LEFT) provides either the left stereo main signal or the monitor signal in mono, depending on the operating mode selected (see (27) ). NEVERuse this output in bridged mono mode. (71) OUTPUT B (RIGHT/BRIDGE) provides either the right stereo main signal, the main mix signal (mono) or the bridged mono signal, depending on the operating mode selected.

In BRIDGE mode always connect only one loudspeaker with an
impedance of at least 8 to the OUTPUT B jack! NEVER use OUTPUT A in BRIDGE mode!
In all other operating modes the impedance of the connected

Sleeve (ground/shield)

loudspeaker must not fall below 4.

Tip (signal)

Fig. 4.1: " TS connector
Balanced " TRS connector
strain relief clamp sleeve ring tip
" TS footswitch connector
strain relief clamp sleeve tip

sleeve ground/shield

sleeve pole 1/ground
ring cold (-ve) tip hot (+ve)
For connection of balanced and unbalanced plugs, ring and sleeve have to be bridged at the stereo plug.

tip pole 2

The footswitch connects both poles momentarily

Fig. 4.2: TRS connector

Fig. 4.4: " mono plug for footswitch
Balanced use with XLR connectors
Power amp insert send return " TRS connector

strain relief clamp

sleeve ring tip
1 = ground/shield 2 = hot (+ve) 3 = cold (-ve)
ring send (out) tip return (in)
Connect the insert send with the input and the insert with the output of the output eects device.


For unbalanced use, pin 1 and pin 3 have to be bridged
Fig. 4.3: XLR connectors Fig. 4.5: Stereo " TRS connector for power amp ISR connection
4.3 Loudspeaker connections
Your power mixer is equipped with high-quality loudspeaker connectors (compatible to Neutrik Speakon), which ensure safe and trouble-free operation. The Speakon connector was especially developed for high-power loudspeakers. Once it is plugged in, it safely locks into position and cannot be accidentally disengaged. It prevents the occurrence of electrical shock and ensures the correct polarity. Each of the loudspeaker jacks carries only the assigned single signal (seethe information given on the rear panel of the powermixer).
Professional speaker connector (compatible with Neutrik Speakon connectors) OUTPUT B 1+ 1+ OUTPUT B

BRIDGE 1+ 1+ 22+

front view rear view
1+ 1122+ 2+ Fig. 4.7: Speakon pin assignment
Fig. 4.6: Professional speaker connector with polarity allocation
Please be sure to only use commercial Speakon cables (type NL4FC) forconnecting your loudspeakers to the power mixer. Please check the pin assignment of your loudspeakers and cables dependent on the PMP speaker output you choose.
EUROPOWER PMP1000/PMP3000/PMP5000 OUTPUT A 1+ 12+ MAIN L x x MONITOR x x MONO x x OUTPUT B x OUTPUT B 1+ 12+ MAIN R x x MONO x x MONO x x BRIDGE x x Tab. 4.1: Polarity configuration of speaker connectors 2-



Drum Computer



Electric guitar CD/TAPE OUT CD-Player Passive Monitors BEHRINGER EUROLIVE F1520 DAT-Recorder IEM (In-Ear-Monitoring)


Electric bass
Fig. 5.5: Expanded set-up
This application is an expanded set-up based on the standard set-up as shown in fig. 5.4, and provides additional connection options. Again, this is just an example, which can be expanded in various ways.

6. Specifications

Microphone Inputs Pre Amp Outputs
Type Mic E.I.N. (20 Hz - 20 kHz) @ 0 source resistance
XLR, electronically balanced, discrete input circuit -134 dB / 136 dB A-weighted
Main Type Impedance Max. output level Monitor Type Impedance Max. output level

Stereo Outputs

1/4" TRS connectors, unbalanced approx. 150 , unbalanced +21 dBu 1/4" TRS connectors, unbalanced approx. 150 , unbalanced +21 dBu
@ 50 source resistance -131.5 dB / 134 dB A-weighted @ 150 source resistance -129 dB / 131 dB A-weighted Frequency response Gain Max. input level Impedance Signal-to-noise ratio Distortion (THD + N)

Mono Line Inputs

< 10 Hz - 155 kHz (-1 dB) < 10 Hz - > 200 kHz (-3 dB) +10 dB, +60 dB +12 dBu @ +10 dB gain approx. 2.6 k balanced / 1.3 k unbalanced 109 dB / 112 dB A-weighted (0 dBu IN @ +10 dB gain) 0.002% / 0.0018% A-weighted
Type Impedance Max. output level Type Impedance Max. output level

Main Mix System Data

RCA approx. 1 k +21 dBu
Type Impedance Max. input level

Stereo Line Inputs

1/4" TS connectors, balanced approx. 20 K +21 dBu
Noise MAIN MIX @ - Channel fader - MAIN MIX @ 0 dB Channel fader - MAIN MIX @ 0 dB Channel fader @ 0 dB

Loudspeaker Outputs

-102 dB/-106 dB A-weighted -88 dB/-91 dB A-weighted -84 dB/-86 dB A-weighted


1/4" TRS connectors, unbalanced > 3.6 k +22 dBu

Low Mid High

CD/Tape Input
80 Hz / 15 dB 2.5 kHz / 15 dB 12 kHz / 15 dB
Type Load impedance MAIN L/R
compatible to NEUTRIK SPEAKON 4-8 4-- 16
RCA approx. 3.6 k, balanced +21 dBu



Power Supply (J)

Converter Dynamics D/A Sampling rate Delay Time Signal run time (Line In Line Out)


24-Bit Delta-Sigma, 64/128-times oversampling 90 dB 46.875 kHz max. 5 s approx. 1.5 ms
Mains voltage Power consumption Fuse Mains connector

Power Supply (CN)

100 - 240 V~, 50 / 60 Hz 500 W T 5 A H 250 V Standard IEC receptacle
Mains voltage Power consumption dual 7-segment LED Fuse Mains connector


Output Power RMS @ 1 % THD (sine wave), both channels driven: 8 per channel 4 per channel per channel 4 per channel Peak Power, bridged mode: 8

Power Supply (EU/A)

Dimensions (H x W x D) Weight
90 W 130 W 200 W 135 W 250 W 500 W
4 7/8 x 15 3/8 x 16 3/4" 122 x 390 x 425 mm 15.435 lbs / 8 kg
RMS @ 1 % THD (sine wave), bridged mode: Peak Power, both channels driven:

Power Supply (UL)

1/4" TRS connectors, unbalanced approx. 150 , unbalanced +21 dBu RCA approx. 1 k +21 dBu
100 V~, 50 / 60 Hz 1000 W T 10 A H 250 V Standard IEC receptacle
220 V~, 50 Hz 1000 W T 6,3 A H 250 V Standard IEC receptacle
215 W 450 W 900 W 300 W 600 W 1200 W
4 7/8 x 18 3/4 x 18 1/8" 122 x 476 x 460 mm 23.815 lbs / 10.8 kg
230 V~, 50 Hz 1000 W T 6,3 A H 250 V Standard IEC receptacle
120 V~, 60 Hz 1000 W T 10 A H 250 V Standard IEC receptacle


-96 dB/-100 dB A-weighted -86 dB/-89 dB A-weighted -83 dB/-85 dB A-weighted
80 Hz / 15 dB 100 Hz - 8 kHz / 15 dB 12 kHz / 15 dB
Mains voltage Power consumption 2 dual 7-segment LED Fuse Mains connector
4 7/8 x 23 1/2 x 19 1/2" 122 x 596 x 496 mm 28.665 lbs / 13.3 kg
BEHRINGER is constantly striving to maintain the highest professional standards. As a result of these efforts, modifications may be made from time to time to existing products without prior notice. Specifications and appearance may differ from those listed or illustrated.
Responsible party name: Address: MUSIC Group Services USA, Inc. 18912 North Creek Parkway, Suite 200 Bothell, WA 98011, USA Phone: +Fax: +673 7647

Phone/Fax No.:

complies with the FCC rules as mentioned in the followingparagraph: This equipment has been tested and found to comply with the limits for a ClassB digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the followingmeasures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician forhelp. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Important information: Changes or modifications to the equipment not expressly approved by MUSIC Group can void the users authority to use the equipment.


Technical specifications

Full description

A seven-band graphic EQ section provides final frequency contouring of audio at the main output. Behringer's FBQ feedback detection system reveals problem frequency bands that may cause feedback and allows users to adjust them. The PMP3000 is a lightweight, portable mixing solution for musicians, and presenters on-the-go. Dual 400 Watt Power Amplifier Internal 400 x 400 watt power amplifier will drive loud speakers directly from the unit. 16 Total Input Channels The PMP3000 features eight mono inputs with balanced XLR microphone and 1/4" phone line inputs. Channels 9/10, 11/12 13/14 & 15/16 are stereo paired with 1/4" phone line inputs for keyboards and stereo line devices. 24 Bit Effects Processor Internal 24-bit effects processor provide 100 preset effects including delay, chorus, reverb, flanger, phaser, etc. Seven Band Graphic EQ A seven-band graphic EQ section provides frequency contouring on output. Behringer's FBQ feedback detection reveals



MH070fxea4A DMD-1000 MC-7847BS UE-40C6800 PDP-V402E DEH-1650 166XL VMX 100 HS030GB PW50-2006 Roland E-38 FXC21 I845 Vegas Sanyo S1 Aspire 5715 KX-FT988FX AT-250 Pioneer A-60 SRS-A212 IC-40S FP93GX Server AD-1110W NWZ-A728B VGN-NS10l S GT1200 6g ED ZWF14070W1 HA28S DSC-T70 P LP820 TX-28DT2 EMX5016CF HTS3610 DEH-P9000R 9600 LSY TX-32LM70F 42MF230A-37B KDC-X589 Antec P180 Review PSS-280 Specs Pilot Schematic SQ-10 XVS1100A-2000 DC728KA Music PRO DTH4500 TX-P37x10E ZOB330X 4 7 EXP-1408A 870A-G54 Bravada 2002 8847MP4 LWG0960PCG 5 3 Philips 105E Sedan 2000 TH-42PV7F Garmin FR60 AJ260 KX-TCD150TR Problems Minolta X700 Gigaset A265 SR-42NMB VGN-T2xp-S F150-1999 Pdf EF2S16 DCM230 Precedus KX-TG1100E NP-N148-dp01 3274-6 KA Case 247-4 FS728TS EP727I Mcbr445B2 930 S RDR-GX300 Tower Gps-200gsec KLV-32M1 LS1040F Pivot STI 764 DZO-V3T T733V Rocker RC-607M Ncpf30PV Inspiron 1100 Nglb23-1H 1737X NN-S225mbepg LE32C450 50PG20R HTR-5140RDS CJ-N75CL WD-10150NP


manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding



1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101