RELEASE NOTE

RELEASE NOTE FOR ROUTER F5D7230-4, FIRMWARE 2.00.05

DATE: JULY 16 2003

These release notes describe features and caveats. The main code module for this release is compatible and downloadable into the switch over the network using the TFTP protocol. Please refer to the Installation and User Guide for a detailed description of the download procedure. Refer to the Belkin User Guide for information about using the embedded web management capability of the switch. This version of software Belkin_2.00.05 supports the following models of the F5D7230-x product family: F5D7230-4
Release notes for 2.00.05 (July 16th 2003)
BELKIN_2.00.05.BIN ----- USA version router image (wireless channel 111)

Bugs fixed:

1. Issue Summary: Firmware updates may result in loss of serial number. This firmware update will resolve lost serial num bers and does not exhibit the error.
Release notes for 2.00.04 (June 20th 2003)
BELKIN_2.00.04 ----- USA version router image (wireless channel 111) BELKIN_AP_2.00.04 ----- USA version AP image (Wireless channel 1-11)
1. Issue Summary: Latest wireless driver that complies with 802.11g and WPA standards.

Issue Summary:

Parental Control : Refresh account sometimes does not work.
Parental Control : Policy Violation Override does not work properly in 2.00.01

7/16/2003

CONFIDENTIAL

PAGE 1 OF 3

RELEASE NOTES BELKIN COMPONENTS, INC.

SOFTWARE RELEASE 2.00.01

Release notes for 2.00.01
BELKIN_2.00.01 ----- USA version router image (wireless channel 111) BELKIN_AP_2.00.01 ----- USA version AP image (Wireless channel 1-11)

Feature Enhancements:

1. 2. Fully compliant with ratified 802.11g specifications. WPA (Wi-Fi Protected Access) support added
Features not supported: 1. Using WPA security over wireless bridging (WDS) feature
1. Issue Summary: 54g router: Router doesn't always display serial # in the home page with version 2.00.00 FW
54g Router: Cannot add MAC addresses on MAC filtering page with 2.00.00 FW
54g Router: Easy Install cannot program router for Static connection with 2.00.00 FW
Issue Summary: 5. Issue Summary: 6. Issue Summary: Fixed Fixed
54g router: User cannot see key generated using Passphrase WEP even before it's applied
54g router web interface login and logout produces brief error message
54g router: Cannot apply Wireless Security while in Acess Point mode
7010 - Wireless sub menu is inconsistent with the left hand menu list.
7230-4 : Textual GUI changes, errors.
BELKIN CONFIDENTIAL PAGE 2 OF 3
9. Issue Summary: hen attempting to change the LAN IP address to a 172.X.X.X number a message is displayed that only a non routable IP address can be used.
Fixed to accept 172.16.0.0/12 as the non-routable IP
Under the heading Internet WAN the word Internet is incorrectly spelt.
Issue Summary: Upon Clicking on the heading Wireless the wording encryption is listed, there is not any heading for encryption this should be labeled Security.
Issue Summary: Saving the router configuration does not give a download dialogue box as described in the manual, but instead opens a text editor.

Upon logging out there is router source code visible.
Issue Summary: maximum length of keys.
When selecting the level of security (WPA/Web) there is no mention of the minimum or
Change WPA-Radius Server to WPA (with Radius Server). And add the following text:
WPA (with server) Advanced Setting - Wireless Protected Access using a server to distribute keys to the clients: This option requires that a Radius server is running on the network. Fixed
16. Issue Summary: Add a checkbox next to Pre-shared Key (PSK) entry that says Obscure PSK. It should be unchecked by default. If the user checks it, the key will be obscured.

BELKIN CONFIDENTIAL

PAGE 3 OF 3

Self Help Guide

A Guide To Wireless Bridging (WDS)
Please read the following carefully;

IMPORTANT!

This Guide refers to the following Products:
Synopsis: The following Guide is designed to give you an understanding of what is meant by the terms Wireless Bridge and WDS. This Guide will also provides a graphical overview as to which Belkin Devices support this feature, and then go on to explain how this feature is activated and configured.
Requirements: In order to complete the steps as outlined in this Guide and set up a functioning Wireless Bridge you will need the following equipment as a basic minimum;
Please Refer To Page 3 For Full List Of WDS Capable Devices
At least 2 of the Devices listed on Page 3 At least one PC with either LAN or WLAN working
This is the minimum required to configure and test the Wireless Bridge to ensure that it is functioning correctly. The amount of equipment required thereafter is dependent on the individual Network requirements.
TSG-UK-1-001 TSG-UK-1-011

www.belkin.com

1 Page 1 of 5
A Wireless Bridge is the name commonly given to the relationship that is formed (wirelessly) between two Infrastructure Devices such as Access Points and Routers. The primary function of a Wireless Bridge is to extend the range of an existing Wireless Local Area Network (WLAN). Wireless Bridging is based on the Wireless Distribution System (WDS) which allows you to make a completely wireless infrastructure. Normally, Access Points must be hardwired to an Ethernet-based LAN. In this way the Access Points allow for a wireless connection to be made to the wired network. The WDS feature allows Infrastructure Devices such as Access Points and Routers to be wirelessly connected to one another. This feature is normally used in large, open areas such as warehouses where wiring might be restricted or not cost effective, and in some larger home environments. Wirelessly Bridging multiple Devices that have all been configured to use the same SSID (Service Set Identifier or Wireless Network Name) will allow in effect Roaming for your Wireless Client Adapters. When they are out of range of one device they will automatically connect to another stronger signal. Wireless Bridges are a very practical, easy, and in most cases inexpensive way to connect two different Ethernet LANs together or extend the range of existing Wireless Networks. They are quick to set up and relatively easy to configure.
Note: The WDS feature is not completely specified in IEEE or WiFi standards. Therefore interoperability between 802.11 products of different Vendors is not guaranteed. We can only recommend and advise on setting up a Wireless Bridge between the Belkin Devices listed on the following page. Please take care to note the Version of the Hardware as well as the Model Number as this may change the nature of the devices compatibility with WDS. The WPA encryption type is not supported over a Wireless Bridge and in such instances WEP is the compatible encryption type.
TSG-UK-1-011 TSG-UK-1-001

Page 1 of 5

Wireless Bridging (WDS) Compatible Devices

F5D7130 v.1*

F5D7130 v.2

F5D7230 v.1*

F5D7230 v.2

F5D7230 v.4*

F5D7230 v.6

F5D7231 v.1xxx**

F5D7231 v.2xxx**

F5D7231-4P**

F5D7235**

F5D7632 v.3 &4

F5D7632 v.5 & 6

F5D7633**

F5D9630 v.3

F5D9630 v.4

Ensure Unit is updated to latest Firmware Version available ** Ensure Unit is updated to latest Firmware Version where applicable and that 125 HSM Mode is disabled.
Configuring Your Device To Enable Wireless Bridging
All the Devices listed on the previous page offer the option for Wireless Bridge in the Menu of the User Interface, under the heading Wireless. Once selected you will see a page similar to that listed below;
Please note the restrictions outlined on this page including the need to have all your Wireless Devices using the same Wireless Channel (1-13) and the same Encryption Key. The only supported Encryption Type is WEP. To enable Wireless Bridging simply tick the first two boxes shown above, Enable Wireless Bridging and Enable Only Specific Access Points To Connect You will then need to manually enter details regarding the Device you wish to bridge with. TSG-UK-1-011 TSG-UK-1-001 | www.belkin.com | Page 1 of 5

The Wireless Networking Device that you are wishing to bridge with has a unique WLAN MAC Address that needs to be located (see Product Label) and entered into the Interface of the device being used to set up the bridge as shown in the example below. Please ensure that the WLAN MAC Address from the Product Label is used, and not the LAN MAC Address which is also to be found there.
Once the WLAN MAC Address of the Bridge Device has been entered and the new settings applied, the Wireless Bridge should be functioning, and a Wireless connection should now be possible between the two devices. The connection can be tested by either Pinging one device from the other or by opening the User Interface of the newly bridged Device. A Device restart may be required. Please note that the F5D7633 is configured in much the same way but the relevant page of the User Interface looks somewhat different and the MAC Address is entered as shown below;

00:11:50:12:34:56

The F5D7633 also offers an Auto discovery option under Wireless Bridge which will essentially display a list of Devices on the same Wireless Channel as your main Device that you can choose from. Their MAC Addresses will all be shown and all you have to do is select the ones youd like to bridge with by ticking the appropriate boxes.