FP71E/FP71E+ LCD Color Monitor 17.0" LCD Panel Size Users Manual

Welcome

i Copyright
Copyright 2004 by BenQ Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of BenQ Corporation.

ii Disclaimer

BenQ Corporation makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranties, merchantability or fitness for any particular purpose. Further, BenQ Corporation reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of BenQ Corporation to notify any person of such revision or changes.
iii Please follow these safety instructions for best performance, and long life for your monitor

Power Safety

The AC plug isolates this equipment from the AC supply. The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet should be installed near the equipment and be easily accessible. This product should be operated from the type of power indicated on the marked label. If you are not sure of the type of power available, consult your dealer or local power company.

Care And Cleaning

Cleaning. Always unplug your monitor from the wall outlet before cleaning. Clean the LCD monitor surface with a lint-free, non-abrasive cloth. Avoid using any liquid, aerosol or glass cleaners. Slots and openings on the back or top of the cabinet are for ventilation. They must not be blocked or covered. Your monitor should never be placed near or over a radiator or heat source, or in a built-in installation unless proper ventilation is provided. Never push objects or spill liquid of any kind into this product.

Servicing

Do not attempt to service this product yourself, as opening or removing covers may expose you to dangerous voltages or other risks. If any of the above mentioned misuse or other accident such as dropping or mishandling occurs, contact qualified service personnel for servicing.

i Table of Contents

Getting started..... 5 Getting to know your Monitor.... 7 Front View....7 Back View (1)....7 Back View (2): Locations of plugs & sockets..8 How to install your monitor hardware... 9 Detach the base.. 11 Adjusting the viewing angle...11 How to install your monitors software... 12 Choosing the best picture resolution... 16 How to choose the right Refresh Rate... 18 How to set the Picture Optimization... 21 How to adjust your Monitor.... 22 A Look at the Control Panel...22 Hot Key Mode....22 Main Menu Mode....23 Troubleshooting..... 32 Frequently Asked Questions (FAQ)...32 Need More Help?...33 Supported operating modes.... 34 Specifications..... 35

Table of Contents

1 Getting started
When unpacking please check you have the following items. If they are missing or are damaged, please immediately contact the dealer at which you purchased the goods. BenQ LCD Monitor

Quick Start Guide

CD-ROM Disk

P / N : 5 3.L 9

Power Cord

Signal Cable: D-Sub

Getting started

Signal Cable: DVI-D

Audio Cable
2 Getting to know your Monitor

Front View

Back View (1)
Getting to know your Monitor
Back View (2): Locations of plugs & sockets
1. Audio Connector 2. Power AC Input Jack 3. DVI-D Connector 4. D-Sub Connector
3 How to install your monitor hardware
Make sure that the computer and monitor's power are both turned off. Please go along with the following steps to install your LCD monitor. 1. Align the base plate to the monitor stand and push it upward until a clicking sound is heard.
2. i.> Connect the power cord to your monitor. ii.> Connect the audio cable to your monitor. iii.> Connect the signal cable (D-Sub and/or DVI-D) to your monitor.
How to install your monitor hardware
3. i.> Connect the power plug to an AC power outlet and switch on. ii.> Connect the other end of audio cable to the audio connector on your computer. iii.> Connect the other end of signal cable to the signal connector on your computer.
4. Connect an earphone into the earphone jack located on the underside of the control panel as shown.
5. Press the Power button on the front panel of the monitor. The power indicator will light up.

Detach the base

Press the Lock button and pull downward to remove the monitor base from the monitor.
Note: Do not insert your fingers into the seam between the base and monitor stand while detaching the base.
Adjusting the viewing angle
Your LCD monitor is designed with a tilt feature that allows you to achieve your optimal viewing angle.
4 How to install your monitors software
You need to set up the correct monitor driver to suit your operating system. Windows 98, turn to page 12. Windows 2000, turn to page 13. Windows ME turn to page 14. Windows XP turn to page 15. Windows 98. To manually install or update the driver, perform the following steps: 1. Open the control panel and double-click Display icon. 2. From the Display Properties window, select the Settings tab. Click the Advanced. button in the bottom right corner. 3. Select the Monitor tab. Click the Change button in the top right corner. 4. The Update Device Driver Wizard opens. Confirm by clicking Next. 5. Select Display a list of all drivers in a specific location, so you can select the driver you want. and press Next. 6. Now click the Have Disk button in the bottom right corner. Another window appears. Select the Browse button. 7. Insert the supplied CD into your computer. Select the CD-drive from the drop-down menu. 8. By pressing OK again in the next window you will be given a list of compatible devices. Select FP71E from the list and press Next again. 9. An Insert Disk dialogue box appears. Click OK, and then click Skip File. 10. Close Update Device Driver Wizard by clicking Finish to complete the installation.

How to install your monitors software
Windows 2000. The first time you start Windows with a new monitor, the system will detect it and automatically start the Add New Hardware Wizard. Carry out the instructions beginning at step 4. 1. Insert BenQ LCD Monitor CD-ROM into your CD-ROM Driver. 2. Click Start then Settings. 3. Open the Control Panel and double click on the Display icon. 4. From the Display Properties window, select the Settings tab. Click the Advanced Properties button in the bottom right corner. 5. Select Monitor then click Properties. 6. Select Driver tab then click Update Driver. 7. The Upgrade Device Driver Wizard will pop up. Then click Next. 8. Select Display a list of the known drivers for this device so that I can choose a specific driver then click Next. 9. In the next window, click Have Disk, then Install From Disk window will pop up. Click Browse, the Located File will pop up. 10. Scroll down and select your CD ROM Driver, then click Next. 11. In the list of folders within the CD-ROM, select Drivers folder then click Open twice, then click OK. Select your LCD Model (FP71E) from the list in the next window then click Next twice. 12. The new drivers are now installed on your computer.
Windows ME. To manually install or update the driver, perform the following steps: 1. Click Start, Settings, Control Panel and then double-click Display. 2. In the Display Properties window, click the Settings tab and click Advanced. 3. Click the Monitor tab and then click Change. 4. Update Device Driver Wizard dialogue box appears. Choose Specify the location of the driver (Advanced) and then click Next. 5. Choose Display a list of all the drivers in a specific location, so you can select the driver you want and click Next. 6. Choose Monitor from the list and then click Next. 7. Choose Display a list of all the drivers in a specific location, so you can select the driver you want. 8. Click Have disk and then click Browse. 9. Insert BenQ LCD Monitors CD into your CD-ROM and type d:\ (change the driver letter to match your CD-ROM driver if it is not drive D). Enter Drivers folder to select the model from the list left. Click OK. 10. Click OK on the Install From Disk window. The dialogue box Update Device Driver Wizard appears. Choose the model from the list, then click Next. 11. Click Next. 12. Click Finish to complete the installation.
Windows XP. 1. Right click mouse on the desktop and choose Properties. Select Settings tab and click the Advanced button. A small window will pop up. Select the Monitor tab in the new window and then click Properties. 2. Select Driver tab and then click Update Driver 3. The Hardware Update Wizard will pop up. Then click Next. 4. Select Dont search. I will choose the driver to install and then click Next. 5. In the next window, click Have Disk, an Install From Disk window will pop up. Click Browse. The Locate File window will pop up. 6. Select FP71E. and then click Next. 7. The new drivers are now installed to your computer. Click Finish to exit installation.

5 Choosing the best picture resolution
Due to the nature of LCD display technology, the picture resolution is always fixed. The best picture possible for your FP71E/FP71E+ is achieved with a resolution of 1280x1024. This is called Native Resolution or maximal resolution - that is, the clearest picture. Lower resolutions are displayed on a full screen through an interpolation circuit. However flaws do occur with the interpolated resolution. So if you want to have all the advantages of LCD technology you must use the native resolution. If you are using Windows 98/2000/ME or XP you can change the picture resolution as follows: 1. Double-click the Display icon in the Control Panel.
2. From the Display Properties window, select the Settings tab. You can alter the resolution by using the slider on the right-hand side.
Choosing the best picture resolution
3. Select a resolution of 1280x1024. Then click Apply.
4. In the subsequent windows, press OK and Yes
5. You can now close Display Properties.
6 How to choose the right Refresh Rate
You don't have to choose the highest possible refresh rate on an LCD display, because it is not technically possible for an LCD display to flicker. The best results are obtained by using the factory modes already set in your computer. There is a table with the factory modes in this users guide. You can choose 60 Hertz, (but not 72Hz) for the native resolution of 1280x1024. In Windows 98/2000/ME/XP you can change the refresh rate as follows: 1. Double click the Display icon in the Control Panel.
How to choose the right Refresh Rate
2. From the Display Properties window, select the Settings tab. Click the Advanced. button in the bottom right corner.
3. Select the Adapter tab. The refresh rate selection field is located in the center at the bottom of the window.
4. Choose a refresh rate from the table with the factory modes, which can be found in the users guide, and select this in the settings field. 5. In the subsequent windows press Change, OK and Yes.
6. You can now close Display Properties.
7 How to set the Picture Optimization
The easiest way to obtain an optimal display is to use the ikey function. Press the ikey on the control panel and the monitor will adjust automatically. If you are still not satisfied with the result, you can still adjust the image manually. 1. Run the test program auto.exe from CD-ROM; this is the best way to observe possible changes. You can also use any other image, such as the desktop of your operating system. However, we recommend that you use auto.exe. As you run auto.exe, a test pattern emerges. 2. Press Enter on control panel to access OSD. 3. If there is vertical noise observed, press or key to select Geometry and press Enter key. or
Then press or key to select Pixel Clock and also press Enter key again. Now, press key to adjust the monitor untill the noise disappears.

4. If there is horizontal noise observed, press or key to select Geometry and press Enter key. Then press or key to select Phase and also press Enter key again. Now, press or to adjust the monitor untill the noise disappears. To make sure the iKey function performs well, you have to use one of the supported modes. If the iKey does not work properly and the NON PRESET MODE message is on the OSD, it means you are not using one of the supported modes. Please set your computer to use one of the supported modes. You will find a list of supported modes in this manual.
How to set the Picture Optimization
8 How to adjust your Monitor
A Look at the Control Panel
There are 7 keys for users control including Enter, , , Exit , Mode , iKey and a power switch. The following descriptions are the introduction of these keys & switch. 1. iKey : Adjust vertical position, phase, horizontal position and pixel clock automatically. 2. Mode key: Switch between different modes, including Standard, Movie 1, Movie 2, and Photo. 3. Exit key: Back to previous menu or exit OSD. The key is also the hot key for volume. 4. 5. (Left) key: For Left/Decrease adjustment. The key is also the hot key for Contrast. (Right) key: For Right/Increase adjustment. The key is also the hot key for Brightness.
6. Enter key: Activate OSD, enter sub menu, select items, confirm selection. 7. Power: Turn the power on or off.

Hot Key Mode

Brightness and Contrast hot key Press to enter Brightness menu, press or
to adjust the degree of brightness and press Exit to exit OSD.
How to adjust your Monitor
Press to enter Contrast menu, press or to adjust the degree of Contrast and press Exit to leave the OSD.
Volume hot key Press Exit to enter Volume menu. Press or key to adjust the degree of volume and press Exit to exit the OSD.
Mode hot key Select your desired mode from these four options: Standard, Movie 1, Movie 2, and Photo. The specified mode will optimize the image properties to best suit the image type. Standard mode is suggested for basic PC application; Movie 1, enhancing color and contrast level, is for viewing videos, while the Movie 2 mode best suits landscape-specific videos; Photo is designed for viewing still images. When done, press Exit to leave the OSD.

Main Menu Mode

Control Functions Available in Main Menu Main Menu The operation mode is displayed in the top right corner of the main menu.

Luminance sub menu

Press or key to adjust the degree of Brightness, press Exit to return to the previous menu.
Press or key to adjust the degree of Contrast, press Exit to return to the previous menu.

Geometry sub menu

Press or key to adjust the Horizontal Position, press Exit to return to previous menu.
Press or key to adjust the Vertical Position, press Exit key to return to previous menu.
or key to adjust the value of the Press Pixel Clock, press Exit to return to previous menu.
Press or key to adjust the degree of Phase, press Exit to return to previous menu.

Color sub menu

User Preset: User may set the color balance of Red, Green and Blue.

OSD sub menu

Press or key to adjust the Horizontal Position of the OSD, press Exit to return to previous menu.
Press or key to adjust the Vertical Position of the OSD, press Exit to return to previous menu.
Press or key to adjust the display time of the OSD, press Exit to return to previous menu.

Language sub menu

Recall sub menu
Press or key to confirm Mode Recall. When you choose "Yes", it will recall the current mode to default settings. Press Exit will return to previous menu.
Press or key to confirm Color Recall. When you choose "Yes", it will recall the current color settings to default settings. Press Exit will return to previous menu.
or key to confirm Recall All. When Press you choose "Yes", it will recall all the current settings to default settings. Press Exit will return to previous menu.

Miscellaneous sub menu

Mode: Select your desired mode from these four options: Standard, Movie 1, Movie 2, and Photo. The specified mode will optimize the image properties to best suit the image type. Standard mode is suggested for basic PC application; Movie 1, enhancing color and contrast level, is for viewing videos, while the Movie 2 mode best suits landscape-specific videos; Photo is designed for viewing still images. When done, press "Enter" to activate the settings. To return to previous menu, press "Exit."
Mode Demo: Mode Demo allows you to preview the effects of the selected Mode from Mode menu. When you choose "On" and press "Enter" to activate Mode Demo, the display will be divided into two windows; the left window demonstrates images of Standard mode, while the right window presents the images under the specified mode. To return to previous menu, press "Exit." Input Select: Select D-sub (analog) or DVI (digital) input to activate the new settings.

Sharpness: Press t or u key to adjust the degree of Sharpness and activate the new settings.

Display Information.

Audio sub menu
Volume: Press or Volume. key to adjust the degree of
Mute: Press or for Mute. key to select ON or OFF

9 Troubleshooting

Frequently Asked Questions (FAQ)
The image is blurred: Read the Installation/Application section, and then select the correct resolution, refresh rate and make adjustments based on these instructions. How do you use a VGA extension cable? Remove the extension cable for the test. Is the image now in focus? If not, optimize the image by working through the instructions in the Installation/Adjustment section. It is normal for blurring to occur due to conduction losses in extension cables. You can minimize these losses by using an extension cable with better conduction quality or with a built-in booster. Does the blurring only occur at resolutions lower than the native (maximum) resolution? Read the Installation/Adjustment section. Select the native resolution. Pixel errors can be seen: One of several pixels is permanently black, one or more pixels are permanently white, one or more pixels are permanently red, green, blue or another color. Read the Pixel error rates section. The image has a faulty coloration: It has a yellow, blue or pink appearance. On the monitor, press Enter key and press or key to move to the Recall icon and press Enter key to enter Recall sub menu. Press or key to select Color Recall and select Yes in Color Recall sub menu, then press Enter key to recall to factory settings. If the image is still not correct and the OSD also has faulty coloration, this means one of the three primary colors is missing in the signal input. Now check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support. No image can be seen: Is the prompt on the display illuminated in green? If the LED is illuminated in green and there is a message Out of Range on the screen, this means you are using a display mode that this monitor does not support, please change the setting to one of the supported mode. Please read Supported operating modes section. Is the prompt on the display illuminated in orange? If the LED is illuminated in orange, the power management mode is active. Press any button on the computer keyboard or move the mouse. If that does not help, check the signal cable connectors. If any pin is bent or broken off, please contact your dealer to get necessary support. Is the prompt on the display not illuminated at all? Check the power supply mains socket, the external power supply and the mains switch.

Troubleshooting

The image is distorted, flashes or flickers: Read the Installation//section and then select the correct resolution, refresh rate and make adjustments based on these instructions. The image is displaced in one direction: Read the Installation//section and then select the correct resolution, refresh rate and make adjustments based on these instructions.

Need More Help?

If your problems remain after checking this manual, please contact your place of purchase or e-mail us at: Support@BenQ.com
10 Supported operating modes
Incoming display mode (Input timing) Horizontal Vertical Pixel Frequency (KHz) Frequency (Hz) Frequency (MHz) 31.47(P) 70.08(N) 25.17 31.47(N) 70.08(P) 28.32 31.47(N) 60.00(N) 25.18 37.86(N) 72.80(N) 31.50 37.50(N) 75.00(N) 31.50 35.16(P) 56.25(P) 36.00 37.88(P) 60.32(P) 40.00 48.08(P) 72.19(P) 50.00 46.87(P) 75.00(P) 49.50 48.36(N) 60.00(N) 65.00 56.48(N) 70.10(N) 75.00 60.02(P) 75.00(P) 78.75 67.50(P) 75.00(P) 108.00 68.68(N) 75.06(N) 100.00 61.80(N) 66.00(N) 94.50 71.81(N) 76.14(N) 108.00 64.00(P) 60.00(P) 108.00 75.83(N) 71.53(N) 128.00 80.00(P) 75.00(P) 135.00 81.18(N) 76.16(N) 135.09
Resolution 640x350 720x400 640x480 640x480 640x480 800x600 800x600 800x600 800x600 1024x768 1024x768 1024x768 1152x864 1152x870 1152x900 1152x900 1280x1024 1280x1024 1280x1024 1280x1024
Comment DOS DOS DOS VESA VESA VESA VESA VESA VESA VESA VESA VESA VESA Macintosh SUN 66 SUN VESA IBMI VESA SPARC2
Modes not listed in the table may not be supported. For an optimal picture, we recommended you choose a mode listed in the table above. There are 22 available modes that are compatible with Windows. Image disruption may occur as a result of signal frequency differences from VGA cards which do not correspond with the usual standard. This is not, however, an error. You may improve this situation by altering an automatic setting or by manually changing the phase setting and the pixel frequency from the Geometry menu. If you switch off the monitor, interference lines can occur on your screen. But do not be concerned about this, as it is normal. To extend the service life of the product, we recommend that you use your computer's power management function.
Supported operating modes

11 Specifications

BenQ FP71E Model Display type Viewable diagonal Native (maximum) resolution Colors Contrast / Brightness Response time Viewing angle (left/right, up/down) Line frequency Image frequency Image checks Controls iScreen functions 17.0" , active, TFT 43.2 cm 1280x1024 16.2 million 500:1 / 300 cd/mms 140/130 (CR=10) 31 - 81 kHz Multi- frequency monitor 56 - 76 Hz modes within these parameters Digital, Screen OSD Technology, iKey (automatic image setting) 6 buttons and iKey. Contrast, brightness, vert. & hor. image position, phase, pixel clock, color balance, color palette, choice of language (8 language OSD), OSD position, status indicator, display-mode availability VESA DPMS, EPA 40 Watt Max (without speaker) 50 Watt Max (with speaker) < 1W, 115V FP71E

BENQ LCD Q7C4 (FP71E) Spare Parts List
P/N: 99.L0Y72.GSA/GSE/GST

ITEM DESCRIPTION

PART NO. 55.L0Y01.011

LOCATION

PCBA I/F BD GENESIS MI IC LCD CTRL GM5221 (BQ6100) 208P IC EEPROM BR24L02F-W SOP 8 IC EEPROM BR34L16F-W SOP 8P IC CMOS 74LVC14A SO-N 14P IC RESET V6300C LO-218V SOT23 IC VR G952T-63U 4P SOT223 IC FLASH PM39LV020-70JC PLCC32 PCBA SPS BD EG01 Q7C4 MI PCBA CTRL BD ACCACM MI LCDM 17 M170EG01 V.0 AUO ASSY RC ABS Y5003A Q7C4 ASSY COLUMN ABS Y5003A Q7C4 ASSY BZL 6-KEY ABS T8020C Q7C4 CTN B 456*423*157 Q7C4 FP71E CSN F EPS Q7C4 FP71E CSN B EPS Q7C4 FP71E SIGNAL DVI-D/DVI-D BLK 2000MM CABLE SIGNAL 15/15P CORE*1 1.5M CD MANUAL 15 LANG FP71E Q7C4 ASSY BASE ABS Y5003A Q7C4
71.05221.B0E U4 72.02402.00P 72.02416.00D 73.07414.061

U1,U3 U7 U16

74.06300.C3B U5 74.95263.03C 72.39020.C33 55.L0Y02.001 55.L0Y03.011 56.91L83.031 60.L0Y04.001 60.L0Y05.001 60.L0Y11.001 44.L0Y01.001 47.L0Y01.001 47.L0Y02.001 50.L5702.501 50.L9005.501 53.L0Y01.001 60.L0Y06.001
* THIS PARTS LIST MAY BE SUBJECT TO CHANGE WITH PRIOR NOTICE BY CSD OF BENQ.

Page : 1 / 1