USER GUIDE

iDECT X2i System
DIGITAL CORDLESS TELEPHONE WITH ANSWERING MACHINE
THIS EQUIPMENT IS NOT DESIGNED FOR MAKING EMERGENCY TELEPHONE CALLS WHEN THE POWER FAILS. ALTERNATIVE ARRANGEMENTS SHOULD BE MADE FOR ACCESS TO DIAL EMERGENCY SERVICES.
Ver. 1, Jul 06 (BTP) Before operating this set, please read these instructions carefully.
BINATONE iDECT X2i System User Guide - Back Page
BINATONE iDECT X2i System User Guide - Front Page 1)White background and black letters 2)Material: 60lb Book Paper 3) Size: 105mm(w) x 148mm(H) A6
Important note emergency calls
The iDECT X2i is not designed for making emergency calls if the mains power fails. So you should make alternative arrangements for access to Emergency Services. (This means that you should also have a basic phone, that does not need mains power, connected to your line so that you can make calls during a power failure.)

If you need help

The Help Line is available from 9.00 am to 5.00 pm, Monday to Friday, on 9677 Calls are charged at Local Call rate.
Unpacking your iDECT X2i system
In the box are: the cordless handset (up to four, depending on which iDECT X2i system youve bought) the base unit two batteries and a battery compartment cover for each handset a telephone line cable for the base unit a mains power lead and adapter for the base unit up to three charger pods, each with a separate mains power lead and adapter, for multi-handset systems Keep the packaging materials in a safe place in case you later need to transport the unit. Keep your sales (till) receipt, which is your guarantee. Before you can use the handset to make calls youll need to fit and fully charge the batteries, as described on pages 5 and 6. Please read the notes on page 4 before you install the base unit.

Where to find it

MENU/OK button Press to start using Menu functions Press while reviewing Phonebook, Redial or Caller Display records, to start editing. When editing or using Menu functions, press to confirm your selection. Phone On/R (Recall) button Press to begin or answer a call, or to use the Recall function You may need the Recall function during a call if your iDECT X2i is connected to a PBX, or if you use BTs Select Services. UP/Caller Display (CID) button Press during a call to increase the volume in the earpiece. Press while using Menu functions to move up through the options. Press to show the list of Caller Display records. SPEAKERPHONE button Press to switch the speakerphone on and off. KEYPAD LOCK button Press and hold to lock the keypad. HANDSET LOCATOR (PAGE) button Press to make all registered handsets ring (this is useful if you've forgotten where you put a handset). HANDSET CHARGING light
/ X (Cancel) button MUTE Press during a call to mute the mouthpiece so the person on the other end cant hear you. Press while editing or using Menu functions, to cancel what youre doing and return the display to Standby mode. HANG UP /ONOFF button Press to end a call. Press and hold for 2 seconds to turn the handset on and off.
Last Number Redial / /Pause button Press to open a list of the last 5 phone numbers you called. Press and hold while dialling to insert a pause (you might need this on a PBX).
/Phone Book button Press during a call to turn down the volume in the earpiece. Press to open the Phone Book. Press while using Menu functions to move through the options. #/INT (Intercom) button Press and hold for 1 second to make an intercom call (if you have more than one handset). IN USE light This comes on when you have a connection to the telephone line, and flashes when the unit is ringing for an incoming call.

To subscribe to network features like Caller Display and Call Waiting, simply call your network service provider (the company that supplies your line). You dont need to do anything special on your iDECT X2i phone to set these features up.

E ANSWER MACHIN

Symbols on the display

18:44 12/08

The time and date

JANE 02:21

The handsets number (if you have more than one handset on your iDECT X2i system) Call Duration.
The handsets name (the default is HANDSET)

What the symbols mean

Signal level New call Intercom call Memory/ store
Ringer Silenced Redialling Keypad Lock
This flashes while the handset is trying to establish a link to the base unit. If flashes while youre on a call, move closer to the base unit. Appears when you have missed incoming calls (if you subscribe to Caller Display). Flashes while your handset is ringing for an intercom call, and comes on steadily when the calls connected. Comes on when youre storing numbers in memory, and when youre making calls to stored numbers. Appears when the ringer volume is set to zero. Appears when you are using last number redial Appears when the keypad is locked. When this shows nearly empty ( ), put the handset on the base unit or charger pod to charge the batteries. While the batteries are being charged, the symbol blinks. Appears when you have a connection to the outside line. Flashes when theres an incoming call to be answered (even if the ringer is turned off). Appears when the answering machine function is on. Flashes when a new message is recieved.

Battery charge

Speakerphone Appears when the speakerphone is turned on.
Help Line: 9677 (Local Call rate)

Contents

Read these notes first 4 To call a stored number 19 To delete all Phone Book entries 21 Caller Display 22
Choosing a site for the base unit and charger pod 4 Radio signals between handset and base unit 4 Mains power connection 4 Installation and set-up Before you start Electrical safety 8 Interference 8 Out of range warning 8 Switching on and off To lock the keypad 9 Your handsets name Time and day Ringer volume and melody Making and answering calls Using the speakerphone 14 To make a call 14 To answer a call 14 To end a call 14 Earpiece volume 15 To mute the mouthpiece 15 Last Number Redial (LNR) 15 To delete redial numbers 16 To store a Redial number in the Phone Book 17 Using the Phone Book To store a new number 8

To check Caller Display records 23 To return a call 23 To store a Caller Display number in the Phone Book 23 To delete a caller display record 24 To delete all caller display records 24 Using a multi-handset system 25
To make an intercom call 25 To end an intercom call 25 To answer an intercom call 26 To transfer a call 26 To shuttle between two calls 27 To set up a three-way conference 27 To end the conference 27 New Call tone 28 To page all handsets from the base unit 28 Answering machine setup 29
X2i answering modes 29 To change answering mode: 29 The outgoing message 30 To record a new outgoing message: 30 Setting the ring delay 31 Call Screening 32 To switch call screening on: 32 Answering machine operation 33
Turn the answering machine on or off: 33 Message Playback 34 To play back recorded messages: 34 To replay the message: 34 To play the next new message: 35 To play the previous message: 35 To delete the current message: 35 To Delete all stored messages: 35 Memo Recording 36 To record a memo: 36 Remote operation To activate remote control: 37 To play messages remotely: 38 Custom settings 39 37
Setting the Alarm 46 To set the alarm: 46 Troubleshooting Cleaning and care Guarantee and service Technical details Registering new handsets To register a new handset 56 To de-register a handset 57 Default setting 55 56
Ringer volume and melody 39 Earpiece volume 39 Registration 42 To reset all handset settings to their defaults: 44 To change the PIN: 45
Connection and conditions for use
You can connect your iDECT X2i to a direct exchange line (DEL) a line connected to a local exchange, with its own phone number; to an extension socket connected to a DEL; or to an extension on an approved compatible PBX. Do not connect the iDECT X2i as an extension to a payphone. The ringer equivalence numbers (RENs) of all instruments (phones, fax machines, etc.) connected to an exchange line must not add up to more than 4 otherwise, one or more of them may not ring and/or answer calls correctly. The iDECT X2i has a REN of 1, and most other telephones have a REN of 1 unless marked otherwise.
Color profile: Disabled Composite Default screen

Read these notes first

Choosing a site The base unit and charger pod(s) should be placed on a for the base level surface, in a position where: unit and the mains adapter plug will reach an easily accessible charger pod 230-V AC switched mains supply socket never try to lengthen the mains power cable the base units telephone line cable will reach your telephone line socket or extension socket (the charger pod does not have a telephone line connection) it is not close to another telephone this can cause radio interference it is not close to a sink, bath or shower, or anywhere else where it might get wet it is not close to other electrical equipment fridges, washing machines, microwave ovens, fluorescent lights, TVs etc. Radio signals between handset and base unit To use your handset and base unit together, you must be able to establish a radio link between them. Be aware that: Any large metal object like a refrigerator, a mirror or a filing cabinet between the handset and the base unit may block the radio signal. Other solid structures, like walls, may reduce the signal strength. IMPORTANT The iDECT X2i base unit and charger pod must be used with the mains adapter supplied with the unit. Using any other adapter will result in noncompliance with EN60950, and will invalidate any approval given to this apparatus.

Press the MENU/OK button Display shows Main Menu >Phonebook Press the button TWICE Display shows Main Menu

>Personal Set

Press the MENU/OK button Display shows Personal Set Press the button ONCE Display shows Personal Set

>Handset Tones

>handset Name
Press the MENU/OK button The display shows Enter Name and the current name. If necessary press the X (Cancel) button to delete characters from the current name. Key in your chosen name When youve finished, press the MENU/OK button Press and hold the HANG UP button to go back to standby mode

Time and day

To set the time and day:
Press the MENU/OK button Display shows Main Menu >Phonebook Press the button ONCE Display shows Main Menu

>Clock & Alarm

Press the MENU/OK button Display shows Clock & Alarm Press the MENU/OK button Display shows 01:01 00/00

>Set Date/Time

Key in the time and date in the format HH:MM DD/MM then press the MENU/OK button Remember to use the 24-hour clock and to include any 0s (zeroes) for example, 9:30 am is 09:30; 6:05 pm is 18:05.
Press the MENU/OK button Any other handsets that have been registered will be automatically updated. Press and hold the HANG UP button to go back to standby mode

Ringer volume and melody

Handset ringer
Press the MENU/OK button Display shows Personal Set Press the MENU/OK button Display shows Handset Tone Press the MENU/OK button Display shows Ring Volume

>Ring Volume

>Low
Use the or button to adjust the volume level between low, medium, high or silence Press the MENU/OK button to select the new level Display shows Handset Tone >Ring Volume Press the button and Press the MENU/OK button The display shows the current melody. Press the or button to play the melodies. When you reach the one you want (there are ten different melodies), press the MENU/OK button to select it The display shows Ring Melody Press and hold the HANG UP button to go back to standby mode

Base unit ringer

>Personal set
Press the MENU/OK button then the button FIVE times Display shows Base Tone >Base Tone Press the MENU/OK button TWICE Display shows BS Ring Vol >Med Use the or button to adjust the volume level between Low, Med, or High Press the MENU/OK button to select the new level, then press the button once Display shows BS Ring Mel Press the MENU/OK button once to begin editing the melody Display shows BS Ring Mel >Melody1 Press the or buttons to play each of the melodies(there are three different melodies). When you reach the one you prefer, press the MENU/OK button Display shows BS Ring Melody >New Melody Press and hold the HANG UP button to go back to standby mode

Number: Enter

If necessary, edit the number Press the MENU/OK button You will hear a long confirmation beep and the redial list will be displayed

Using the Phone Book

You can store up to 200 numbers in the Phone Book. Each number can have up to 24 digits, and can be stored with a name of up to 12 characters (including spaces). To store a 1 new number Press the MENU/OK button TWICE*

The display shows

Phonebook >New Entry
Press the MENU/OK button The display shows Enter Name:
Key in a name then press the MENU/OK button The display shows Enter Number: _ Edit or Key in the new number** Press the MENU/OK button You will hear a long confirmation beep Press MENU/OK again to begin a new phonebook entry
Only press the MENU/OK button once if the number is already displayed on screen (because it has been pre-dialled or you have pressed Redial).
** Use the MUTE/CANCEL button to delete characters.
To call a 1 stored number
Press the Phone Book button The display shows the first entry in the Phone Book. Press the or button to go up or down the list to the number you want OR you can search by pressing a button on the numeric keypad for the first letter of the name, then using the and buttons if necessary. Press the PHONE or Speaker button to dial the number

To use a direct memory

Long press (key 1 to key 9) will automatic dial out the stored direct memory.
To add or 1 delete the direct memory
Press the Phone Book button Select direct memory sub-menu. Select key 1 to key 9 by and key. Press the OK button to select the key to add or delete number. The current number or 'no number' will be shown. Press the OK button to active add or delete the number.
If add, scroll over names of phonebook to

be added for this key.

Press the OK button to confirm, a beep will be heard.
To edit a Phone Book entry
Press the MENU/OK button TWICE Display shows Phonebook >New Entry Press the button TWICE The display shows Phonebook

>Edit Entry

Press the MENU/OK button and use the or buttons to find the entry you want to edit The display shows PHONEBOOK >Eric Press the MENU/OK button The display shows Enter Name

>Eric

To edit the name, use the MUTE/CANCEL button to delete characters, then key in the new ones (See page 17).Press the MENU/OK button to confirm the changes 89 Display shows Enter Number > To edit the number, use the MUTE/CANCEL button to delete digits, then key in the new numbers
Press the MENU/OK button to complete the edit The display shows PHONEBOOK >Eric Press and hold the HANG UP button to go back to the edit entry menu
To delete a Phone Book entry
Press the MENU/OK button twice then the button three times
Phonebook >Delete Entry

Press the MENU/OK button, then the or button to find the entry The display shows Phonebook > and the entry name. Press the MENU/OK button You will hear a confirmation beep Press and hold the HANG UP button to go back to standby mode Press the MENU/OK button twice then the button four times Display shows Phonebook >Delete All
To delete all Phone Book entries
Press the MENU button The display shows Delete
Press the MENU/OK button to confirm You will hear a confirmation beep and the display will show Phonebook >List Empty for 2 seconds Press and hold the HANG UP button to go back to standby mode

Caller Display

To subscribe to this feature, you need to contact your service provider, who will tell how much it will cost. Caller Display lets you see the phone numbers of your callers on the handsets display, before you answer. The iDECT X2i will store the numbers of the last 20 callers (whether or not you answered the call) so you can call them back later. When the Caller Display list is full, the next incoming number will overwrite the oldest one. If youve got new Caller Display records, the is shown on the display. symbol
Here are some examples of Caller Display records:

Call List >Jenny

A call from someone whose name (Jenny) and number are stored in your Phone Book. Press the (Down) button once to see the full number. Press the button again to see more details. In this example, the most recent call came 4:21 pm on 15th.
Call List >15/04 16:21

Call List >0123467809

A call from someone whose name and number are not stored in your Phone Book.
A call from someone who withheld their number by dialling 141.

Call List >(PRIVATE)

Call List >(Out of Area)
A call from someone whose number is unavailable (for example, this may be an international call).
To check 1 Caller Display records
Press the Call Log Display button Display shows Call Log >Call List Press the MENU/OK button Display shows Call list > and the first entry in the list Press the or button to scroll through the records The CID icon is on for new call records. Once youve checked all new records, the symbol disappears from the display.

To end an intercom call

To answer an intercom call
The ringing tune for intercom calls is different from that for outside calls. When someone makes an intercom call to you, your handsets display shows INTERNAL FROM # with the number of the handset calling you.
Press MENU/OK or the speakerphone button to answer When youre talking on an outside call (a call youve either made or answered), you can transfer it to another handset:

To transfer a call

Press and hold the INT/# button until Intercom flashes on the display. Then key in the number of the other handset The outside call is put on hold and the other handset rings. When the other handset user answers, you can speak to her/him. If the other user does not answer, you can get back to the outside call at any time by pressing and holding the INT/# button again.
Press the HANG UP button to hang up and transfer the call If you prefer, you can press HANG UP to transfer the outside call before the other handset answers your intercom call. If the user hasnt answered after 30 seconds, the outside call will come back to you and your handset will ring.
To shuttle between two calls
When you have made or answered an outside call and then made an intercom call, you can shuttle from one to the other, like this:
Press and hold the INT/# button for one second to speak to each in turn, putting the other on hold You can transfer the outside call to the other handset by pressing HANG UP while youre connected to the intercom call If you press HANG UP while youre connected to the outside call, youll disconnect it.
To set up a three-way conference
Make or answer an outside call Press and hold the INT/# button to start intercom mode then key in the number of the other handset The outside call is put on hold and the other handset rings. When the other user answers: Press the INT/# button for one second Use the BACK/MUTE key to turn off the handset microphone and the or button to adjust the volume.

To end the conference

Press the HANG UP button You will drop out of the conference call, leaving the other user connected to the outside call.

New Call tone

When you are on an intercom call and an outside call comes in, youll hear New Call tone to tell you that someone is calling you. To answer the outside call and end the intercom call: Press the PHONE button briefly OR, to answer the outside call and put the intercom call on hold (so you can later use shuttle, conference or transfer): Press the INT/# button for one second If you now want to set up a three-way conference, simply press and hold the INT/# button for one second.

Use the buttons to adjust the ring delay between 1 and 8 rings or Toll Saver If you select Toll Saver the telephone will be answered after 5 rings, reducing to 3 rings if there are new messages.
Press the MENU/OK button to confirm the new setting Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Call Screening

The call screening function allows you to listen to incoming messages as they are recorded so you can decide if you would like to take the call. The X2i is supplied with call screening switched off. Press the MENU/OK button ONCE then the button ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then the button FIVE times Display Shows Ans Machine >Settings Press the MENU/OK button ONCE then the button TWICE Display shows Settings >HS Screening Press the MENU/OK button Display Shows HS Screening Press the button Display Shows HS Screening

>Off

To switch call 1 screening on:

>On

Press the MENU/OK button to confirm the change Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
Answering machine operation
When the answering machine is switched on the TAM icon on the handset display will come on steadily. When the answering machine is recording a message the TAM icon will flash and the caller ID will be displayed If call screening is on the SPKR icon will come on and the incoming message can be heard on the speaker
08453459677 ICM Recording
To stop the recording and take the call, simply press the PHONE button in the normal way Turn the 1 answering machine on or off: Press the MENU/OK button ONCE then the button ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button TWICE then the button ONCE Display Shows Ans Machine >Answer On/Off Press the MENU/OK button Display Shows Answer On/Off
Press the button to select Off and then the MENU/OK button to confirm Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Message Playback

The X2i can a number of messages in its memory. The messages will be available for replay until you delete them to make room for new messages. n New messages that have not yet been 18:44 12/08 played are indicated by the TAM icon flashing and the New Message icon JANE 1 showing. 1 New ICM
When messages that have been played are stored on the X2i the TAM icon stays on steadily.
To play back 1 recorded messages:
Press the MENU/OK button ONCE then the button ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE Display shows Ans Machine >Play The first new message will play in the loudspeaker. n Use the buttons to adjust the speaker volume. n Press the REDIAL/PAUSE button to switch the display between the caller's number and the time and date of the message. n Press SPKR to play the message through the handset earpiece

To replay the 1 message:

Press CANCEL to stop the message playing Press the MENU/OK button ONCE Display shows Play >Repeat Press the MENU/OK button ONCE The message will replay
To play the next new message:
Press the MENU/OK button ONCE and the button ONCE Display shows Play >Next Message Press the MENU/OK button ONCE The next message will play Press the MENU/OK button ONCE and the button TWICE Display shows Play >Prev Message Press the MENU/OK button ONCE The previous message will play Press the MENU/OK button ONCE and the button THREE times Display shows Play >Delete Press the MENU/OK button ONCE The current message will be deleted Press the MENU/OK button ONCE then the button ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then the button TWICE Display shows Ans Machine >Delete All Press the MENU/OK button Display Shows Delete all >Confirmquestion Press the MENU/OK button to confirm. Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
To play the previous message:
To delete the 1 current message:
To Delete all 1 stored messages:

Memo Recording

The X2i will allow you to record a memo message that can be replayed later. This can be useful if you want to leave a message for other users of the phone.

To record a memo:

Press the MENU/OK button ONCE then the button ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then TWICE Display Shows Ans Machine >Record Memo Press the MENU/OK button Display Shows Recording Memo. Speak into the handset to record your memo. Press the MENU/OK button to end the recording Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Remote operation

The X2i will allow you to check your messages remotely from another phone. To use this function you must call using a tone dialling telephone and you will need to enter your X2is master PIN. The remote control function must be activated before it can be used, and will not function unless the master PIN has been changed from the default (see page 45). To activate remote control:
Press the MENU/OK button ONCE then ONCE Display Shows Main Menu >Ans Machine Press the MENU/OK button ONCE then ONCE Display Shows Ans. Machine >Settings Press the MENU/OK button ONCE then TWICE Display Shows Ans Settings >Remote Access Press the MENU/OK button Display Shows Remote Access

>Deactivated

Press the button to select between Activated and Deactivated Display Shows Remote Access >Activated Press the MENU/OK button to confirm the selection You will hear a confirmation beep Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode
To play messages remotely:
Call your telephone number and wait for the answering machine to answer You will hear a voice prompt Within 4 seconds enter your master PIN followed by # You will hear a long confirmation beep. Any new messages will be played immediately. Once the messages have been played you can use the telephone buttons as follows: n Press 1 to go to the previous message n Press 2 to play or stop playback n Press 3 to go to the next message n Press 6 to delete the current message n Press 0 turn the answering machine on or off If you stop pressing the buttons your X2i will wait 15 seconds and then hang up.
Answering machine settings

Default settings

This option returns the answering machine to its default settings: n answering machine off n default OGM1 selected n no recorded incoming messages or memos n remote PIN 0000 n message recording time 120 seconds (2 minutes) n time stamping on n rings to answer five n call monitoring on n recording quality standard

Custom settings

The iDECT X2i can be customised to suit your preferences in a number of ways. Some of these functions have been covered earlier in this User Guide. This section is a roundup of items that have not yet been mentioned. When making a change to a setting you can press the HANG UP button at any point to cancel what youre doing and go back one step. When youre keying in numbers, if you make a mistake, press the HANG UP button to delete digits. Ringer volume and melody Earpiece volume See page 12 for details.
There are five earpiece volume levels which can changed during a call using the or buttons.

Key beep

To turn off the key beep tone: Press the MENU/OK button ONCE and the button TWICE Display shows Main Menu >Personal Set Press the MENU/OK button Display shows Personal Set >Handset
Press the MENU/OK button ONCE and the button TWICE Display shows Handset tone >Key Beep
Press the MENU/OK button Display shows Key Beep >On Use the or button to select ON or OFF Press the MENU/OK button You will hear a confirmation beep Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Auto-answer

With auto-answer turned on, you can answer an incoming call by simply lifting the handset from its place on the base unit or charger pod.
To turn auto-answer on and off: Press the MENU/OK button and the button TWICE Display shows Main Menu >Personal Set Press the MENU/OK button ONCE and the button TWICE Display shows Personal Set >Auto Pick-up Press the MENU/OK button Display shows Auto Pick-Up

The master PIN

The Master PIN (personal identity number, or security code) is required when handsets are registered and deregistered, and when important changes to the settings are made. The default setting for the PIN is 0000. To protect your handsets settings, we recommend that you change it to a four-digit number youll easily remember.

To change the PIN:

Press the MENU button The display shows Main
Press the button THREE times The display shows Main Menu >Advance
Press the MENU/OK button then the button Four times Display shows Advance Set >Change PIN Press the MENU/OK button Display Shows Enter PIN Key in the current PIN (default = 0000) and press the MENU/OK button Display shows Enter New PIN: Key in the new PIN number and press the MENU/OK button Display shows Confirm PIN: Key in the PIN again and press the MENU/OK button You will hear a long confirmation beep Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Setting the Alarm

The iDECT X2i can provide a one off or a regular daily alarm signal. When the alarm time is reached the LCD backlight will blink and you will hear the alarm tone for one minute.

To set the alarm:

Press the button ONCE The display shows Main Menu
Press the MENU/OK button then the button ONCE Display shows Clock & Alarm >Alarm Press the MENU/OK button Display Shows Off Use the or button to select between Off, ON Once or On Daily. Press the MENU/OK button Display prompts for the alarm time Key in the time and press the MENU/OK button Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Selecting an alarm tone

You can choose from three different alarm tones:
Press the MENU/OK button then the button TWICE Display shows Clock & Alarm >Alarm tone Press the MENU/OK button Display Shows Alarm Tone >Melody
Use the or button to select between melodies 1, 2 or 3. Press the MENU/OK button You will hear a long confirmation beep Use the CANCEL button to exit the menu or press and hold HANG UP to go to standby mode

Troubleshooting

ALWAYS check first that:
The iDECT X2i must be serviced by trained engineers. NEVER attempt any repairs or adjustments yourself you could make the problem worse and invalidate the Guarantee.
you have followed all the steps listed on pages 5 to 7 to install and set up your iDECT X2i all connectors are firmly inserted in their sockets mains power is switched on at the socket the handsets batteries are correctly and securely installed, and are not run down

If the fault persists

Disconnect all other instruments connected to the same line as the iDECT X2i and see whether you can make a call. Disconnect the base unit from the telephone line and plug a different phone into the master telephone socket. Try making a call. If this works, the line is OK. If the call does not work, and you are using a two-way socket adapter, remove it and plug a telephone directly into the socket. If the call now works, the adapter may be faulty. If you cannot make a call, the fault may be on the exchange line. Contact the service provider (the BT engineers on 151, or your cable company). If you still cannot identify the cause of the problem, contact the Help Line on 9677.

Cleaning and care

Do not clean any part of your iDECT X2i with benzene, thinner or other solvent chemicals this may cause permanent damage which is not covered by the Guarantee. When necessary, clean it with a damp cloth. Keep your iDECT X2i away from hot, humid conditions or strong sunlight, and dont let it get wet. Every effort has been made to ensure high standards of reliability for your iDECT X2i. However, if something does go wrong, please do not try to repair it yourself consult your supplier or the Help Line.
Declaration of conformity
The Binatone iDECT X2i complies with the essential protective requirements and objectives of:
EC R&TTE Directive 1999/5/EC EC Low Voltage Directive 73/23/EEC EC EMC Directive 89/336/EEC
and conforms to the following relevant harmonised standards:
Radio: EN 301406 EMC: EN 301489-1, EN 301489-6 Safety: EN 60950-6, All: 2004
Binatone Telecom plc operates a policy of continuous product improvement, and so reserves the right to make changes to the product and functions without notice.

Guarantee and service

The iDECT X2i is guaranteed for 12 months from the date of purchase shown on your sales receipt. The Guarantee does not cover damage by misuse or negligence, or by excessive voltages for example, faults on the telephone line, or lightning. Please keep your sales (till) receipt this is your guarantee. You should also keep the original packaging material. In the unlikely event that you need to return your iDECT X2i to our Repair Centre while it is under guarantee, there will be a 5 handling charge. While the 1 Disconnect the base unit from the telephone line and the mains electricity supply unit is under Guarantee 2 Pack up all parts of your iDECT X2i, using the original packaging. Remember to include the mains adapter

Registration failed?

REGISTRATION FAILED
If registration has failed, the handsets display will show for a few seconds then return to standby mode. If this happens, try again, making sure you dont leave too long between steps. If you still cant register the handset, contact the Help Line for advice.

To de-register a handset

You may need to do this in order to replace a faulty handset. Press the MENU button The display shows Main Menu >Phonebook Press the button THREE times The display shows Main Menu >Advance
Press the MENU/OK button then the button THREE times Display shows Advance Set >Unregister Press the MENU/OK button The display shows Unregister

>1. 2. 3. 4

Select the handset number you want to deregister then press the MENU/OK button
You will hear a long confirmation beep. The display shows Unsubscribed
To register to a different brand of base unit
Your iDECT X2i can be registered to any GAPcompatible base unit; or your can register other GAPcompatible handsets to your iDECT X2i base unit. But we do not guarantee that all features or display messages will be available using other manufacturers equipment. 1 Follow the instructions in the base units User Guide to put the base unit into registration mode (for example, step 7 on page ). 2 Follow the instructions in the handsets User Guide to register the handset (for example, steps 1 to 5 on page ). If you need to enter a PIN for the base unit, refer to the base units User Guide.

Default

For returning all settings to their default values, as follows: Keypad unlocked Redial list empty Caller Display records empty Reminder list empty Alarm Clock off Earpiece volume 3; speakerphone volume 3 Area Code none Handset ringer volume Medium; melody 1 Base unit ringer volume Med; melody 1 Key tone on Auto-answer On Handset name Handset Language English Dialling type tone Flash timing 100 ms CID mode FSK Master PIN 0000

A answering a call, 14

answering an intercom call, I 26 auto-answer, 41 handset settings, 39 - 47 installation, 5 - 7 intercom calls, 25 interference, 4, 8

B base unit ringer, 13

batteries charging the handsets batteries, 7 fitting the batteries, 6 replacing the batteries, 41

K key beep, 40 L

language, 43 Last Number Redial, 15 on a PBX, 52 locking the keypad, 9
C Caller Display, 22 - 24
checking records, 23 deleting records, 24 returning calls, 23 storing numbers in the Phone Book, 23 cleaning and care, 53 clock setting, 11 conference calls, 27 connection and conditions for use, 3

M making a call, 14

memory dialling, 19 multi-handset use, 25 - 28, 47

N name, 10

New Call tone, 28
O Out of range warning, 8 P the Phone Book, 18 - 21
calling a stored number, 19 deleting entries, 21 editing entries, 20 storing names and numbers, 18 paging handsets, 28 pause, 52, 55 PBX compatibility, 41, 45 PIN handset, 45 problems, 48 - 52