QuickSteamer

USERS GUIDE
1770/1970 SERIES QUICKSTEAMER 2080 SERIES QUICKSTEAMER POWERBRUSH 2090 SERIES QUICKSTEAMER MULTISURFACE

Safety Instructions

Product View

Assembly

Operations

Maintenance

Troubleshooting

Consumer Services

Replacement Parts

Warranty

ug603-5603_1770_206.indd 1

2/28/06 4:26:45 PM

Thanks for buying a BISSELL QuickSteamer
Were glad you purchased a BISSELL QuickSteamer Lightweight deep cleaner. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your QuickSteamer is well made, and we back it with a limited oneyear warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, youll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your QuickSteamer. Thanks again, from all of us at BISSELL.
Mark J. Bissell President and Chief Executive Officer

www.bissell.com

800.237.7691
ug603-5603_1770_206.indd 2

2/28/06 4:26:51 PM

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following: Read all instructions before using your QUICKSTEAMER
To reduce the risk of fire, electric shock, or injury:
Do not immerse. Use only on surfaces moistened by cleaning process. Always connect to a properly grounded outlet. See Grounding Instructions. Unplug from outlet when not in use and before conducting maintenance or troubleshooting. Do not leave machine when it is plugged in. Do not service machine when it is plugged in. Do not use with damaged cord or plug. If appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, have it repaired at an authorized Service Center. Do not expose to rain. Store indoors. Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces. Do not carry the appliance while in use. Do not unplug by pulling on cord. Unplug by grasping the plug, not the cord. Do not handle plug or appliance with wet hands. Do not put any object into appliance openings, use with blocked opening, or restrict air flow. Do not expose hair, loose clothing, fingers or body parts to openings or moving parts. Do not pick up hot or burning objects. Do not pick up flammable or combustible materials (lighter fluid, gasoline, kerosene, etc.) or use in the presence of explosive liquids or vapor. Do not use appliance in an enclosed space filled with vapors given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapors. Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, gasoline, etc.). Do not modify the 3-prong grounded plug. Do not allow to be used as a toy. Do not use for any purpose other than described in this Users Guide. Use only manufacturers recommended attachments. Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage. See the Cleaning Fluid section of this guide. Keep openings free of dust, lint, hair, etc. Keep appliance on a level surface. Turn off all controls before unplugging. Be extra careful when cleaning stairs.

WARNING:

Close attention is necessary when used by or near children. WARNING: The Power Cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

SAVE THESE INSTRUCTIONS.

THIS MODEL IS FOR HOUSEHOLD USE ONLY. Commercial use of this unit voids the manufacturers warranty.

GROUNDING INSTRUCTIONS

This appliance must be connected to a grounded wiring system. If it should malfunction or break down, grounding provides a safe path of least resistance for electrical current, reducing the risk of electrical shock. The cord for this appliance has an equipment-grounding conductor and a grounding plug. It must only be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Grounded Outlets

Grounding Pin
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you arent sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

ug603-5603_1770_206.indd 3

2/28/06 4:26:52 PM

Spray Trigger

Quick Release Cord Wrap

Power Cord

Handle Assembly

Clean Water/ Solution Tank Lower Cord Wrap Upper Body

Lower Body

Large Easy Rolling Wheels

Power Switch

Detent Lever
Vent Cover (Containing Foam Filter) Collection Tank Collection Tank Latch

BISSELL Formulas:

Removable Nozzle
These items are available for purchase with your model. To order replacement parts or additional tools or formulas, please refer to page 11.
48 oz. Fiber Cleansing Formula with Scotchgard Protector
48 oz. MultiAllergen Removal Formula with Scotchgard Protector
48 oz. Pet Odor and Soil Removal Formula with Scotchgard Protector
48 oz. BISSELL Natural Orange Extract Formula with Scotchgard Protector
22 oz. Tough Stain PreCleaner
32 oz. Hard Floor Solutions
ug603-5603_1770_206.indd 4

2/28/06 4:26:54 PM

How to Use this Guide
This Users Guide has been designed to help you get the utmost satisfaction from your BISSELL QuickSteamer Lightweight Deep Cleaner. Youll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this Guide thoroughly before assembling your Deep Cleaner.
Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this Users Guide will greatly enhance your ability to get the most performance from your BISSELL QuickSteamer for many years. Your QuickSteamer comes in three, easy to assemble components: Handle assembly Upper Handle assembly Clean/Solution Tank 3 Screws The only thing you will need to assemble your cleaner is a Phillips head screwdriver.
Assembling Your QuickSteamer

1. 2. 3. 4. 5.

Slide Upper Body into Lower Body.
Secure with Screws. Slide Strain Reliever Handle down into Upper Body until it will go no further. Secure with Screw. Place Clean/Solution Tank on back of unit.

Special Features

Clean/Solution Tank - holds 1/2-gallon of hot water and cleaning solution. Collection Tank - holds 1/2-gallon of dirty water. Power Cord - for storage, wrap Power Cord around Upper and Lower Cord Wraps, and secure plug to Cord with molded clip.
ug603-5603_1770_206.indd 5

2/28/06 4:27:17 PM

How to Use Your BISSELL QuickSteamer

Before You Clean

1. 2. 3. 4.
Plan activities to give carpet time to dry. Remove easily moved furniture (chairs, lamps, coffee/cocktail tables, etc.) from room if needed. Vacuum carpet thoroughly. Decide where to begin and end your job. Clean in 3 X 4 sections, starting in areas farthest from exit. Plan to leave a path open to empty soiled water and refill cleaner. Carpeting will dry in three to four hours, depending on carpet style and air circulation in room. A floor fan speeds drying. Replace furniture on damp carpeting by placing waxed paper under legs until floor dries completely.

To reduce the risk of fire, use only BISSELL Cleaning Formulas for Deep Cleaning Machines. Use of cleaning formulas that contain lemon or pine oil may damage this appliance and void warranty. Chemical spot cleaners or solvent-based soil removers should not be used. These products may react with the plastic materials used in your QuickSteamer, causing cracking or pitting.

Fill the Tank

1. 2. 3.
Remove the Clean/Solution Tank by lifting it straight up, then away from the Lower Body. Unscrew the black cap at the bottom of the Clean/Solution Tank. Add one of the BISSELL Advanced Cleaning formulas for Deep Cleaning machines to the formula fill line on the Clean/Solution tank. Fill the rest of the tank with hot (not boiling) tap water to the water fill line. Replace and tighten the black cap. Place Clean/Solution Tank on Lower Body. Rotate Quick Release Cord Wrap to release the Power Cord and plug into an outlet.
Always vacuum thoroughly before you deep clean. If possible, move large furniture to an area you will not be cleaning.

Pre-Treating

Pre-treat stubborn stains and highly soiled carpet in hallways and other high-traffic areas. 1. 2.
Using BISSELL Tough Stain pre-cleaner, generously spray evenly over soiled area, do not overwet carpet. Wait 3 -5 minutes before deep cleaning.
Deep cleaning spots, spills and high traffic areas on a regular basis can prolong carpet life.
ug603-5603_1770_206.indd 6

2/28/06 4:27:21 PM

Carpet Cleaning

1. 2. 3. 4. 5. 6. 7. 8.

With your foot, press the red Power Switch [located in foot of unit] ON. With foot, press the Detent Lever on right side of Lower Body. Depress Spray Trigger to spray cleaning solution. Do not overwet. To suction up water, repeat motion over same area without depressing Trigger. Repeat Steps 3 and 4 until no more dirt can be removed. Continue to clean entire carpet, working in 3 x 4 sections. Empty the Collection Tank when dirty water reaches the full line, or when the Clean/Solution Tank is empty. See page 8 for instructions. If Floor Nozzle stops spraying, turn Power Switch OFF and check water and cleaning solution levels. Refill if needed.
It is recommended that every time your Clean/Solution Tank is emptied of solution that you empty the contents of the Collection Tank. If the Collection Tank gets too full, you may begin to see foam spitting out of the vent cover. When this happens you will know it is time to empty the Collection Tank.

Hard Floor Cleaning

Attach Hard Floor Tool to Unit. Remove the Collection Tank (refer to #3a and b in the Routine Maintenance section on page 8) A. For 1770/1970 series it is necessary to remove the Cross Action Brush first. Using your thumbs squeeze the 2 grey tabs towards the outside of the unit. Push down at the same time and release the Cross Action Brush. Attach the Hard Floor Tool by hooking it into the front of the removable nozzle and swinging it down until the tabs pop into place. Replace the Collection Tank. Be sure to attach the 2 latches. Fill Clean/Solution Tank with BISSELL Hard Floor Solutions to FORMULA fill line. Fill Clean/Solution Tank with hot (not boiling) tap water to the WATER fill line. Follow steps 1-8 in Deep Cleaning section above. 3

3. 4. 5. 6. 7.

2080/2090 series

1770/1790 series

ug603-5603_1770_206.indd 7

2/28/06 4:27:25 PM

Cleaning Fluid Section
Keep plenty of genuine BISSELL Fiber Cleansing Formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas.
WARNING: Fire To Reduce the Risk of
and Electric Shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner. NonBISSELL cleaning solutions may harm the machine and void the warranty.
48 oz. BISSELL Fiber Cleansing Formula with Scotchgard Protector item # 0710A
48 oz. BISSELL Multi-Allergen Removal Formula with Scotchgard Protector item # 0720A
48 oz. BISSELL Pet Odor and Soil Removal Formula with Scotchgard Protector item # 0730A
48 oz. BISSELL 32 oz. BISSELL Natural Orange Hard Floor Solutions Extract Formula with item # 0484 Scotchgard Protector item # 0740

Routine Maintenance

When You're Done
Turn Power Switch OFF. Unplug Power Cord from outlet. Remove and empty Collection Tank. a. Release Collection Tank latches [1 each side] by
WARNING:injury To reduce the risk of
from moving parts and/or electrical shock, turn Power Switch OFF and disconnect plug from electrical outlet before performing maintenance or troubleshooting checks.

lift by handle

pulling up from bottom of latch and then out.
b. Carefully lift Collection Tank from Lower Body. c. Carry Collection Tank to a toilet or sink. To
empty, pour out contents using opening at back of Tank. d. Rinse Collection Tank thoroughly. e. Remove lint and hair from Red Gasket in base of unit. (Do not remove gasket)

4. 5. 6. 7.

Clean Nozzle Window by lifting latch and removing c. from machine. Rinse under running water. When finished replace Nozzle and secure with latch. Replace Collection Tank on Lower Body and secure with latches. Wrap Power Cord around Quick Release Cord Wrap on side of QUICKSTEAMER. Wipe all surfaces with a soft cloth. Store cleaner upright in a protected, dry area.

CLEAN AFTER EACH USE

NOTE: You may have cleaning solution remaining in the Clean/Solution Tank. You may store your QuickSteamer this way for the next cleaning task, but never keep soiled solution in the Collection Tank.
CAUTION: Do not store unit
where freezing may occur. Damage to internal components may result.

ug603-5603_1770_206.indd 8

2/28/06 4:27:26 PM

To Install the Replacement Brush Belt
*QuickSteamer PowerBrush models only 1. 2. 3.
Turn the machine off and unplug from wall outlet. Remove Clean/Solution and Collection Tanks. Lie machine down to access the bottom of the machine. 4. With a Phillips head screwdriver, unscrew the Brush Cover and remove. 5. Remove the Brush End Cap and remove belt from brush. 6. Brush can now be removed. 7. Belt can be removed by sliding off the Motor Pulley. 8. Clean or replace belt. Attach belt to Motor pulley and brush, insert brush into right side End Cap. 9. Reattach the left End Cap and slide brush back into place. 10. Replace the brush cover and screw into place.

Brush Cover

ug603-5603_1770_206.indd 9

2/28/06 4:27:44 PM

Reduced Spray Or No Spray.

Possible Causes

1. Clean Tank empty
Remedies 1. Refill Tank with water and formula Remedies 1. Check Tank proper alignment and secure with side latches 2. Empty Tank 3. Align four "hooks" into bottom first, then snap into place on top
Deep Cleaner Not Picking Up Cleaning Solution.
1. Collection Tank not aligned/secured 2. Dirty Tank full 3. Removeable Nozzle installed improperly
Thank you for selecting a BISSELL product.
If you should happen to need assistance during assembly or operations, call 1-800-237-7691
Please do not return this product to the store
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services 1-800-237-7691

Monday - Friday Saturday

Or write: BISSELL HOMECARE, INC PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Services
8 a.m. 10 p.m. EST 9 a.m. 8 p.m. EST
Or visit the BISSELL website - www.bissell.com
When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See "Warranty" on page 12 for details.
ug603-5603_1770_206.indd 10

2/28/06 4:27:48 PM

Replacement parts - BISSELL QuickSteamer
Below is list of common replacement parts*. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired.

Part No.

Part Name
QuickSteamer 1770/1970 Series
5 203-5519 203-5545 203-5537 203-5522 203-5547 Handle Assembly Cross Action Brush Clean/Solution Tank Collection Tank Hard Floor Tool

QuickSteamer PowerBrush 2080/2090 Series
1 203-5520 Handle Assembly 3 203-5540 Clean/Solution Tank 4 203-5523 Collection Tank 6 203-5546 Dirt Lifter PowerBrush 7 203-5549 Belt 8 203-5548 Hard Floor Tool 9 0710A Fiber Cleansing Formula 48 oz 10 0720A Multi-Allergen Removal Formula 48 oz 11 222-0400 Tough Stain PreCleaner 12 0730A Pet Odor and Soil Removal Formula 48 oz. Hard Floor Solutions * Not all parts included with every model.
ug603-5603_1770_206.indd 11

2/28/06 4:27:49 PM

Warranty - BISSELL QuickSteamer
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited One Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product BISSELL Homecare, Inc. will repair or replace (with new or remanufactured components or products), at BISSELLs option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part. See information below on "If your BISSELL product should require service". This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, neglect, unauthorized repair, or any other use not in accordance with the User's Guide is not covered.
If your BISSELL product should require service:
Contact BISSELL Consumer Services to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Services.
Website or E-mail: www.bissell.com Use the Customer Services tab. Or Call: BISSELL Consumer Services 1-800-237-7691 Monday - Friday 8 a.m. - 10 p.m. ET Saturday 9 a.m. - 8 p.m. ET Or write: BISSELL Homecare Inc. PO Box 3606 Grand Rapids MI 49501 ATTN: Consumer Services
BISSELL HOMECARE, INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELLS LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE. 2006 BISSELL Homecare, Inc Grand Rapids, Michigan Some states do not allow limitations on how long an implied warranty lasts, All rights reserved. Printed in China so the above limitation may not apply to you.

NOTE: Please keep your original sales receipt. It is your warranty.
Part Number 603-5603 Rev 02/06 Visit our website at: www.bissell.com
Scotchgard is a trademark of 3M
ug603-5603_1770_206.indd 12

2/28/06 4:27:56 PM