Grounded Outlets

Grounding Pin
Improper connection of the equipment-grounding conductor can result in a risk of electrical shock. Check with a qualified electrician or service person if you arent sure if the outlet is properly grounded. DO NOT MODIFY THE PLUG. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance is designed for use on a nominal 120-volt circuit, and has a grounding attachment plug that looks like the plug in the drawing above. Make certain that the appliance is connected to an outlet having the same configuration as the plug. No plug adapter should be used with this appliance.

WARNING:

Product view

CleanShot Trigger

Spray Trigger

R TE WANSE I

Power Switch Extra Long Power Cord

Heater Switch

Flex Hose Upper Handle
Easy Carry Handle Heat Indicator Light Tank Carry Handle ReadyTools Dial 2-in-1 Water Tank CleanShot Lower Base Dry Aire Easy To Remove Nozzle Edge Sweep Brushes Detent Pedal

Upper Hose Rack

Hose Secure Latch Upper Handle TurboBrush Storage Crevice Tool Holder
Lower Hose Rack Lower Base
W ARNING: reduce the risk of fire and To

Detent Pedal

electric shock due to internal component damage, use only BISSELL cleaning fluids intended for use with the deep cleaner. Non-BISSELL cleaning solutions may harm the machine and void the warranty.

Formula Tank

Cleaning fluid
Keep plenty of genuine BISSELL 2X Multi-Allergen Formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and will void the warranty.
BISSELL 2X Fiber Cleansing Formula with Scotchgard Protection www.bissell.ca
BISSELL 2X Multi-Allergen Removal Formula with Scotchgard Protection
BISSELL 2X Pet Stain and Odor Removal Formula with Scotchgard Protection
BISSELL 2X Professional Deep Cleaning Formula with Scotchgard Protection
BISSELL 2X Hard Floor Solutions Formula
BISSELL Tough Stain PreCleaner

Assembly

Your ProHeat 2X comes in three, easy to assemble components: Upper Handle Lower Handle Tool Caddy The only thing you will need to assemble your cleaner is a Phillips head screwdriver. 1. 2. 3. 4.

Slide upper handle onto lower handle. Screw 3 screws into the marked holes. Place upper hose rack onto back of upper 1.
Warning: not plug in your Do
cleaner until you have completely assembled it per the following instructions and are familiar with all instructions and operating procedures.
handle, and secure with tapered screw.
Place lower hose rack onto back of upper
handle by pushing in and sliding down until it snaps into place. figure 5. figure 5.

5. 6. 7.

Snap tools into the tool caddy as shown in Wrap power cord and flex hose as shown in Keep flex hose snugly in place by using

the hose secure latch.

ProHeat 2X assembly is now complete.

Crevice Tool Holder

Tough Stain Brush TurboBrush Spraying Crevice Tool

Hose Secure Latch

Special features
Your BISSELL ProHeat 2X deep cleaner is a home cleaning system that uses the power of heat, brushes and cleaning formula to get the deep down dirt for a maximum clean. Not only does it come with a lot of unique features, it has been designed with you, the customer, in mind.

Built-in-Heater feature

BISSELL ProHeat 2X models all feature a patented built-in heater which will heat the hot tap water you put in up to 25 F degrees (14oC) hotter to safely optimize cleaning effectiveness. The heater will never allow the temperature to exceed 190 F degrees (88oC). The heater switch on the front of the machine controls the heater so you have the option to turn off the heat if you are cleaning delicate wool or oriental rugs.
Dual DirtLifter PowerBrushes
The two DirtLifter PowerBrush rolls are designed to enhance cleaning performance. The bristle pattern safely lifts out the deep down dirt while gently grooming carpet fibers. The floating suspension self-adjusts to all carpet heights. Once the product is in the upright position, the brushes automatically stop spinning.

Custom Clean

The Custom Clean feature automatically mixes hot tap water with the BISSELL formula. Simply choose one of the 4 settings (heavy traffic, normal clean, light clean, or water rinse) and the ProHeat 2X will adjust the right amount of cleaning solution to mix with the heated water to fit your cleaning need. Having a separate solution tank from the water tank also allows no waste of formula. Because the water and solution are stored separately, they are not mixed until you are ready to clean. When your cleaning job is finished, the formula can be stored ready to use in your machine for the next time!
(located on upper handle)

CleanShot

The CleanShot feature gives you the ability to tackle tough stains with the push of a button. Cleaning solution is sprayed in a concentrated stream, penetrating the stain and allowing for better cleaning focus. Simply spray and suction and the stain is gone! CleanShot is especially effective for spots and stains that would otherwise take a lot of deep cleaning cycles to remove. It allows the cleaning formula and machine to do the work for you.

Dry Aire

The Dry Aire system spreads hot air across the carpet to aid in drying. The feature runs while your machine is powered. Heated air is distributed from the bottom and back of the machine and blown across the carpet while you clean!

Flow Gauge CleanShot

Flow Gauge
The flow gauge is located on the rear cover of your unit and is a convenient performance feedback indicator. The flow gauge will spin when the trigger is depressed and: There is liquid in both the clean water tank and the formula tank OR Custom Clean is set to rinse and there is water in the clean tank The flow gauge will stop spinning when: The trigger is let go The unit runs out of clean water The unit runs out of cleaning formula

2-in-1 water tank

Our 2-in-1 water tank full capacity system is designed with a heavy duty bladder inside for clean water. As you clean, the clean water in the bladder will empty and mix with the cleaning formula. Dirty water pulled out of your carpets will collect around the outside of the bladder so that clean and dirty water are always kept separate. This allows the user to maximize tank space, yet only carry one tank to and from the sink for emptying and filling.
Easy to remove and clean nozzle
Now, cleaning up your machine after the cleaning process is easier than ever! Simply remove the 2-in-1 Tank and remove the screw to pop out the nozzle for rinsing in the sink. Dirt, loose carpet fibers and remaining pet hair or fuzz get washed away in a snap.

ReadyTools dial

This provides either floor cleaning or above floor cleaning with the turn of a knob. If choosing above floor cleaning for upholstery, stairs, or for those creases close to the baseboards, turn knob to "TOOLS" and choose the attachment appropriate for the job. Attach tool to the flex hose and you are ready to go. Be sure to turn knob back to "FLOOR CLEANING" when done.

F CL LOOR G EANIN

Scotchgard Protector
Carpet protection applied at the mill typically wears down over time from heavy foot traffic and everyday cleaning, including deep cleaning. To help restore this important protection, only BISSELL offers deep cleaning formulas with Scotchgard protector. This offers extra protection against dirt and tough stains to keep your carpets looking good longer. To maintain your Scotchgard 5-year limited stain warranty, you no longer are required to hire a professional. By using your BISSELL ProHeat machine with BISSELL formulas containing Scotchgard protector every 12 months, your carpet warranty from 3M remains in effect. No other home deep cleaning system can do this for you. Refer to the Scotchgard protector warranty for details.

Operation

Before you clean
1.Plan activities to give your carpet time to dry. 2. 3. 4. Move furniture to another area if cleaning an entire room (optional). Vacuum area with a dry vacuum cleaner thoroughly before deep cleaning. Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit.

BRUSH SUCTION

S H TA E R R
Before you clean (continued)
5. Pretreating (optional) Pretreating is recommended to improve cleaning effectiveness for heavily soiled carpet in high traffic areas such as entryways and hallways. Option A: BISSELL Tough Stain PreTreat A.Spray the BISSELL Tough Stain Pre-treat formula onto heavy traffic areas, soiled areas, or stains. B.Allow to penetrate for at least 3 minutes. C.Clean as normal, using the BISSELL ProHeat 2X machine on the high traffic setting, following the instructions below. Option B: CleanShot A.Set Custom Clean for the desired setting. B.Press the CleanShot button and aim the focused stream onto the stain. Allow the formula to soak in for 30 seconds. C.Run the machine over the stain to extract. Repeat as needed until the stain is gone. D.Rinse if desired.

ATTENTION:

Some Berber carpets have a tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition. Please see Stain Removal instructions on page 15.

Carpet cleaning

1. Fill the 2-in-1 Water Tank. Remove the tank from the base of the machine by lifting up the tank carry handle. Carry like a bucket to the sink.
1a. Unlatch the top of the tank from the bottom by lifting up on the tank latch which is located on the back of the tank. 1b. Remove the top of the tank by lifting up on the handle.
Note how the lip on the top tank separates from the groove in the bottom tank. This placement is important when putting the tank back together

Lip Groove

1c. Fill the heavy duty bladder with clean hot tap water.*Do not boil or microwave water as it can destroy the bladder. 1d. Leaving the filled bottom of the tank on a flat surface, only maneuver the top of the tank. To attach the top part of the tank to the bottom, carefully hook the lip on the top tank into the groove on the bottom tank. 1e. Fasten tanks together by securing the latch in the back.

Carpet cleaning (Continued)
After cleaning, you may want to turn the Custom Clean dial to rinse to give your carpeting a final water only rinse. This will ensure thorough removal of embedded dirt loosened by the deep cleaning formula. BISSELL deep cleaning formulas contain an anti-resoiling agent that helps your carpets repel dirt and keeps them looking good longer.
Remove the tank from the base of the machine by lifting up on the tank carry handle. Carry like a 7. bucket to a utility sink or outside where you will dispose of the dirty water. 7a. Unlatch the top of the tank from the bottom by lifting up on the tank latch which is located on the back of the tank. 7b. Remove the top of the tank by lifting up on the handle.
Note how the lip on the top tank separates from the groove in the bottom tank. This placement is important when putting the tank back together.
7c. Lift the bottom portion of the tank; pour out dirty water toward the sink through the triangular shaped opening in the corner of the tank.
Note: You may notice hair & debris deposits on the carpet or in the tank that were loosened by the 7d. cleaning action (especially with newer carpets that have never been deep cleaned before). This debris should be picked up and thrown away.
7d. Fill the heavy duty bladder with clean hot tap water, following instructions 1c through 1e on page 10.
Note: Remember to secure the tank latch in the back and test to make sure it is secure before picking up the tank. Always check the level of cleaning formula in the formula tank at the same time, and refill as needed.
Water rinse (Optional). Rinsing is an optional step that can be done during the cleaning process by switching from one of the clean settings on the Custom Clean dial to a water rinse setting, or it can be done after the carpeted area has been cleaned. Simply choose the water rinse setting on the custom clean dial, and follow the same path as you did for cleaning, taking care to do a forward (wet) stroke by depressing the trigger, a backward (wet) stroke, and a forward and backward (dry) stroke, releasing the trigger. Continue this until the water you see coming up the nozzle is clear.
9. CleanShot. CleanShot is an optional feature that can be used to fight tough stains. It can be used as either a tough stain pre-treat (see page 10) or can be used during the deep cleaning process itself. To use CleanShot either as a pre-treat or during deep cleaning, follow the instructions below. A.Set Custom Clean for the desired setting. B.Press the CleanShot button and aim the focused stream onto the stain. Allow the formula to soak in for 30 seconds. C.Run the machine over the stain to extract. Repeat as needed until the stain is gone. D.Rinse if desired.
Cleaning with attachments
Your ProHeat 2X machine comes equipped with a hose and at least one attachment for cleaning stairs, upholstery, and more. 1. Important! If using to clean upholstery, check upholstery tags. A. Check manufacturers tag before cleaning. W or WS on the tag means you can use your ProHeat 2X. If the tag is coded with an X or an S (with a diagonal stripe through it), or says Dry Clean Only, do not proceed with any deep cleaning machine. Do not use on velvet or silk. If manufacturers tag is missing or not coded, check with your furniture dealer. B. Check for colorfastness in an inconspicuous place. C. If possible, check upholstery stuffing. Colored stuffing may bleed through fabric when wet. D. Plan activities to allow upholstery time to dry. E. Vacuum thoroughly to pick up loose debris and pet hair. Use a vacuum with a brush attachment and a crevice tool to clean in fabric folds.

Manufacturers tag

bvh g kvh gh j j h d b lg fd hn l kl sd jkn f h Ad bj jh b j cv hh gcg
Cleaning with attachments (continued)
2. Follow the instructions on pages 10 & 11 for filling the 2-in-1 water tank and the formula tank. 3. Set ReadyTools dial to the hose attachments setting. This will allow spray and suction from the hose. 4. Set custom clean dial for heavy traffic, normal clean, light clean, or water rinse as desired. 5. Attach the cleaning tool to the end of the hose. 6. Plug in and turn on the power switch and heater (if desired). 7. Clean by pressing the trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the trigger to suction soiled water. Continue to clean in the area, working in small sections, until no more dirt can be removed. Rinse (optional) and suction as needed. Caution: Do no overwet. 8. Remove and rinse tools in clean, running water. Dry and replace in the tool caddy. 9. It is recommended that you suction clean water from a bowl to rinse out the hose. 10. Before replacing lift end of hose and stretch out to ensure all water is cleared from hose. 11. Coil flex hose around the tool caddy. 12. Empty 2-in-1 water tank and rinse out, following the instructions on page 12. 13. Return ReadyTools dial to floor setting.

10. 5.

W ARNING: reduce the risk of To
injury, be extra careful when cleaning stairs. Make sure machine is secure and level.

Stain removal

Do Not Delay! Attending to an accident soon after it occurs ensures the most optimal clean. Leaving it for an extended period of time may cause it to set and become permanent. 1. Blot up liquids with an absorbent cloth or paper towels. White materials are recommended because certain dyes may bleed and make the stain worse. 2. Gently scrape up any semi-solids with a spoon or spatula. Do not use a knife or other utensil with sharp edges because it could damage the carpet or upholstery. If the area has dried, remove the remaining semi-solids and residue with a sweeper or vacuum. Be sure to test any spot removal formulas in an inconspicuous area first. This is important as some dyes and materials could be damaged or discolored by cleaning solvents. If such a change should occur, try a different solution or call a professional. If cleaning on Berber carpeting, gently run your machine over a hidden area. If no fuzzing occurs, continue cleaning in soiled area. CleanShot. CleanShot is an optional feature that can be used to fight tough stains. It can be used as either a tough stain pre-treat (see page 10) or can be used during the deep cleaning process itself. To use CleanShot either as a pre-treat or during deep cleaning, follow the instructions below. A.Set Custom Clean for the desired setting. B.Press the CleanShot button and aim the focused stream onto the stain. Allow the formula to soak in for 30 seconds. C.Run the machine over the stain to extract. Repeat as needed until the stain is gone. D.Rinse if desired. 7. Clean using either the FLOOR CLEANING, or TOOLS setting on the ReadyTools dial.

Hard floor cleaning

Your ProHeat 2X model may have come with a hard floor attachment and Hard Floor Solutions Formula. If not, these products are available for purchase by contacting the BISSELL Consumer Services department by phone or at the website. The hard floor tool provides effective cleaning for linoleum, vinyl, and tile floors. Caution: Do not use on unsealed hardwood floors. 1. Vacuum or sweep thoroughly to pick up any loose debris and pet hair. 2. 3. Move any furniture, if needed. Fill with water to "WATER" line. Fill with BISSELL 2X Hard Floor Solutions to "FORMULA" line. Fill the 2-in-1 water tank with hot tap water and set aside. Attach the hard floor tool onto the bottom of the machine by hooking it into the nozzle and swinging it down until it clicks into place. Check ReadyTools dial. It should be set on floor cleaning. Set the Custom Clean dial to normal clean. Plug into an outlet and turn the power switch and heater ON ( I ). Slowly move the machine forward and back over hard floor surface one time while depressing trigger. Caution: Do not overwet.
To reduce the risk of fire and electric shock- when cleaning a hard floor, the BISSELL hard floor tool 2035642 must be used and it must only be used with BISSELL Hard Floor Solutions or BISSELL 2X Hard Floor Solutions cleaning fluid intended for use with this appliance.

6. 7. 8. 9.

10. Repeat the motion without pressing the trigger using the hard floor tool to squeegee and suction up the dirty water. 11. Allow adequate time for floors to dry. 12. Remove hard floor tool, rinse and dry before storing. 13. If any formula remains in the formula tank, pour it back into the Hard Floor Solutions bottle for use the next time. 14. Rinse out the formula tank.

Maintenance and care

Machine storage
Once your cleaning is complete, make sure the 2-in-1 water tank is emptied, rinsed out, and dried before the next use. The formula tank can remain filled and ready to go.
Note: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is a danger of freezing. Freezing will damage internal components and void the warranty.

Machine care

For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Turn power and heater switches OFF (O). Unplug the machine and wrap the power cord. 2. After emptying the 2-in-1 water tank, rinse it out at a faucet with running hot tap water, taking care to clean underneath the heavy duty bladder, and all around it. The top half of the tank can be rinsed clean through the nozzle area. Also, pop out the red filter underneath the top half of the tank and rinse that out. Replace before putting the top and bottom halves of the tank together. Before you place the cleaned 2-in-1 water tank back onto the machine, simply unscrew the floor nozzle using a Phillips head screwdriver. This can be rinsed out at the faucet. Then replace back onto the machine by starting from the bottom of the nozzle and hooking the tabs into the holes on the bottom sides of the machine. Secure into place with the screw.

W ARNING: reduce the risk of fire, To
electric shock or injury unplug from outlet before servicing.

Filter

Let all parts dry completely before storing

Machine care (continued)

5. The inside of the end caps by the brush rolls can be wiped out with a clean paper towel, or, if a more thorough cleaning is desired, the end caps can be taken off using a Phillips head screwdriver and rinsed clean. Replace after cleaning. Any loose hair or debris can be pulled from the brush rolls and thrown away. For the most thorough clean before storage, follow directions on pages 18 & 19 for removal and replacement of the brush rolls and belts. To clean attachments that may have been used, remove from hose and rinse in clean, running water. Dry and replace attachment in the tool caddy. Clean the hose by suctioning clean water from the tap. Before replacing, lift end of hose and stretch out to ensure all water is cleared from hose. Refer to page 14, illustrations 9 & 10. hair and fuzz.
electric shock or injury, unplug from the outlet before servicing.
8. After carpet is dry, vacuum again to remove
Small belt removal and replacement
Occasional replacement of one or both belts may become necessary. If that is needed, please follow the instructions below. 1. Turn off the machine, and unplug it from the outlet. 2. 3. 4. 5. Remove both the 2-in-1 water tank and the formula tank. Set aside. Unscrew the front nozzle and remove it. Set aside. Turn the machine on its side. IMPORTANT: cord side down. Remove the clear end cap by unscrewing the 2 black screws. Take care not to drop the screws into the unit. Remove 1 silver screw from the pivot arm. Remove pivot arm by gently lifting up. Remove small brush belt. Replace small brush belt, and reverse steps above.

1-800-263-2535 8. 9.

Brush removal and large belt replacement
Brushes can be removed for cleaning or replacement as needed. 1. Follow small belt removal Instructions on page 18. 2. 3. Remove brush rolls by pulling them off of the metal rods. Place cleaned or new brush rolls back onto the rods. Make sure one washer is on each end of the rollers prior to sliding onto the rod. Be sure to let the rod slide through the bushing to insure proper fit. Re-attach the long belt on the bottom to the cogs of the small roller brushes. Place small belt over back roller and metal cog. Place pivot arm in place and screw in place using the silver screw. Re-attach clear end cap by tightening with the (2) black screws. Return front nozzle to front of unit, by latching from underneath and then securing with a screw. If you have any questions or are having trouble installing or replacing your belt(s) or brushes, please call BISSELL Consumer Services at 1-800-263-2535.

4. 5. 6. 7. 8.

Troubleshooting
Built-in heater ready light does not illuminate

Possible Cause Remedies

1. The heater switch is not turned ON ( I ). 1. Turn the heater switch ON ( I ). 2. The power switch is not turned ON ( I ). 2. Both switches must be ON ( I ) to activate the heater ready light.

Reduce Spray or No Spray

1. Water tank may be empty. 1. Fill heavy duty bladder with hot tap water. 2. Formula tank may be empty. 2. Fill formula tank with BISSELL Multi Allergen Formula for cleaning.
www.bissell.ca 1-800-263-2535
Reduce Spray or No Spray (continued)
3. Tank may not be seated completely. 3. Turn power OFF ( O ). Remove and reseat tank. 4. Pump may have lost prime. 4. Turn power OFF ( O ) and then back ON ( I ). Wait one minute, then depress Trigger.
DirtLifter PowerBrushes do not turn
1. The belt is off or broken. 1. Turn power OFF ( O ) and unplug unit from outlet. Follow instructions on page 18. 2. The unit is in the upright position. 2. Brushes only rotate when unit is reclined using the detent pedal.
3. Circuit breaker may have tripped.
3. Turn the machine OFF ( O ) and
unplug from outlet. Check to see if foreign object is caught in brush roll. Remove object. Plug machine back in to reset circuit breaker.
Cleaner not picking up solution
Remedies 1. ReadyTools dial may be at wrong setting. 1. Set ReadyTools dial to either FLOOR CLEANING or TOOLS setting. 2. Tank may not be seated properly. 2. Pick up both the 2-in-1 water tank and formula tank and reseat them so they fit snugly on the unit. 3. Tank may not be assembled properly. 3. Check to make sure the "lip" of the nozzle is securely hooked into the groove on bottom of Tank (see page 10). 4. Solution or 2-in-1 water tank is empty. 4. Check fluid levels in heavy duty bladder and formula tank. 5. 2-in-1 water tank has picked up 5. Empty 2-in-1 water tank. Refill maximum dirty water and red float heavy duty bladder with clean door has closed. hot tap water and replace. 6. Red float "door" in the tank may have closed 6. Turn the machine OFF ( O ), as a result of bumping an object or moving allowing red float door to release into machine back and forth too quickly. the open position. Turn unit back ON ( I ) to continue cleaning. Be sure your forward and backward strokes are done at a slower pace.

Possible Causes

Other maintenance or service not included in the manual should be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
For any questions or concerns, BISSELL is happy to be of service. Contact us directly at 1-800-263-2535.
BISSELL Consumer Services
For information about repairs or replacement parts, or questions about your warranty, call:
BISSELL Consumer Services 1-800-263-2535

Monday - Friday Saturday

Or write: BISSELL Canada Corporation Box 1003 Niagara Falls, ON L2E 6W2 ATTN: Consumer Services
8 a.m. 10 p.m. ET 9 a.m. 8 p.m. ET
Or visit the BISSELL website - www.bissell.ca or www.2Xbissell.ca
When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________
NOTE: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See Warranty on page 24 for details.
Replacement parts - BISSELL ProHeat 2X (Continued)

Part No.

203-6611 Grey Tank Assembly (complete) 203-6660 Grey Tank Lid 203-6618 Grey Tank Bottom 203-6675 Cap and Insert for Water Tank 203-6676Formula Tank (includes Cap & Insert for Formula Tank) 203-6677 Cap and Insert for Formula Tank 203-6678Front Nozzle (includes gasket) 203-6679 Autoload Gasket (fits both Water and Formula Tank) 203-6845Float Door 203-6680 Tank Filter (Lint Screen) 203-6681 Water Tank Latch 203-6682 Cord Wrap (Black) (Blue or Purple cord wrap available upon request) 203-6685 Clear End Cap w/Edge Brushes (2 pack, includes screws) 203-6686 Brush Roll 6 row (includes 1 brush, axle, 2 swivel arms) 203-6688 Small Brush Belt (non-cord side) 203-6804 Large Brush Belt (cord side) 203-6689 Hose Secure Latch 203-6690 Hose Rack Assembly (Top/Bottom Hose Rack, Screws) 203-6994 CleanShot Cover

Part Name

*Not all parts are included with every model. 5 6

Accessories

Replacement Parts* Below please find a list of common replacement parts. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired. 11 12
203-6651 203-6652 203-6653 203-6654 203-6655 203-5642 62E5 C/D 99K5 C 89Q5 C/D 14N3 C 81TD
3 Tough Stain Tool Powered TurboBrush Hand Tool 4 Upholstery Tool 6 Stair Tool Spraying Crevice Tool Bare Floor Tool, with trial size bottle of Hard Floor Solutions formula 2X Fiber Cleansing Formula with Scotchgard Protection 2X Pet Stain and Odor Removal Formula with Scotchgard Protection 2X Multi-Allergen Removal Formula with Scotchgard Protection 2X Professional Deep Cleaning Formula with Scotchgard 2X Hard Floor Solutions Formula Tough Stain Precleaner
Warranty - BISSELL ProHeat 2X Healthy Home
If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by E-mail, telephone, or regular mail as described below.
Limited ONE Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, upon receipt of the product, BISSELLCanada Corporation will repair or replace (with new or remanufactured components or products), atBISSELLs option, free of charge from the date of purchase by the original purchaser, for one year any defective or malfunctioning part. See information below on If your BISSELL product should require service. This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to routine maintenance components such as belts or brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with the Users Guide is not covered. Call BISSELL Consumer Services at the number listed below or visit the BISSELL website www.bissell.ca to locate a BISSELL Authorized Service Centre in your area. If there are no authorized BISSELL Service Centres in your area, a BISSELL Representative at canada.custhelp@bissell.ca or at the phone number below will issue you a Return Authorization Number and a pre-paid mailing label to return the unit to BISSELL for warranty repair. The machine should be returned with a photocopy of your proof of purchase. (Your dated sales receipt is your warranty do not send original.) If you need information about repairs or replacement parts, orif you have questions about your warranty, contact BISSELL Consumer Services.

If your BISSELL product should require service
Website: www.bissell.ca E-mail: canada.custhelp@bissell.ca Or Call: BISSELL Consumer Services 1-800-263-2535 Monday Friday 8 a.m. 10 p.m. ET Saturday 9 a.m. 8 p.m. ET Or write: BISSELL Canada Corporation Box 1003, Niagara Falls, ON L2E 6W2 ATTN: Consumer Services
BISSELL CANADA CORPORATION IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELLS LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE ONE YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
NOTE: Please keep your original sales receipt, it is your warranty.
2010 BISSELL Homecare, Inc BISSELL Canada Corporation Niagara Falls, ON L2E 6S5 All rights reserved. Printed in China Part Number 120-4168 Rev 01/10 Visit our website at: www.bissell.ca Scotchgard is a trademark of 3M