PROheat All-Rounder

USERS GUIDE

7700 SERIES 220-240V

Safety Instructions

4-5 Product View

Assembly

7-8 Special Features

8-13 Operation
14-15 Maintenance and Care

16 Troubleshooting

17 Consumer Services

18-19 Replacement Parts

20 Warranty
ug120-4005_7700_607.indd 1

6/28/07 10:05:17 AM

Thanks for buying a BISSELL PROheat All-Rounder
Were glad you purchased a BISSELL PROheat All-Rounder cleaning system. Everything we know about floor care went into the design and construction of this complete, high-tech home cleaning system. Your PROheat All-Rounder is well made, and we back it with a limited two-year warranty. We also stand behind it with a knowledgeable, dedicated Consumer Services department, so, should you ever have a problem, youll receive fast, considerate assistance. My great-grandfather invented the floor sweeper in 1876. Today, BISSELL is a global leader in the design, manufacture, and service of high quality homecare products like your PROheat All-Rounder. Thanks again, from all of us at BISSELL.
Mark J. Bissell President and Chief Executive Officer

www.bissell.com

ug120-4005_7700_607.indd 2

6/28/07 10:05:20 AM

IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precautions should be observed, including the following:
READ ALL INSTRUCTIONS BEFORE USING YOUR CLEANING SYSTEM.
Always connect to a properly Earthed outlet. Unplug from outlet when not in use and before conducting maintenance or troubleshooting.

WARNING: To reduce the

risk of fire, electric shock, or injury:
Use indoors only Do not immerse Use only on surfaces moistened by cleaning process Do not leave machine when it is plugged in Do not service machine when it is plugged in If the supply cord is damaged, it must be replaced by the manufacturer or its service agent in order to avoid a hazard Do not use machine if it has been dropped, damaged, left outdoors or dropped into water Do not expose to rain, store indoors Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around sharp corners or edges, run appliance over cord, or expose cord to heated surfaces Do not carry the appliance while in use Do not unplug by pulling on cord; unplug by grasping plug not the cord Do not handle plug or appliance with wet hands Do not put any object into appliance openings, use with blocked opening or restrict air flow Do not expose hair, loose clothing, fingers or body parts to openings or moving parts Do not pick up hot or burning objects Do not pick up flammable or combustible materials (lighter fluid, petrol, kerosene, etc.) or use in the presence of explosive liquids or vapours Do not use appliance in an enclosed space filled with vapours given off by oil base paint, paint thinner, some moth proofing substances, flammable dust, or other explosive or toxic vapours
Remove plug from electrical outlet before cleaning or maintaining the appliance Not intended for use by young children or infirm persons without supervision Young children should be supervised to ensure that they do not play with the appliance Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, petrol, etc.) Do not modify the Earthed plug Do not allow to be used as a toy Do not use for any purpose other than described in this Users Guide Use only manufacturers recommended attachments Use only cleaning products formulated by BISSELL for use in this appliance to prevent internal component damage Keep openings free of dust, lint, hair, etc. Keep appliance on a level surface Turn off all controls before unplugging Be extra careful when cleaning stairs Pay close attention when working around children

SAVE THESE INSTRUCTIONS.

THIS MODEL IS FOR HOUSEHOLD USE ONLY.
WARNING: This appliance must be Earthed. IMPORTANT Hz POWER ON FOR OPERATION A 220-240 VOLT A.C. 50/60
SUPPLY ONLY. If your appliance is fitted with a nonrewireable BS 1363 plug it must not be used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in the carrier contained in the plug. Spares may be obtained from your BISSELL supplier. If for any reason the plug is cut off, it must be disposed of, as it is an electric shock hazard should it be inserted into a 13 amp socket.
ug120-4005_7700_607.indd 3
Product view - water ltrated vacuum mode

Carry Handle

Top Lid

Extra Long Power Cord

Quick Release Hose Door
Collection Tank Handle Wand Collection Tank Hose Solution Line
Air Powered Floor TurboBrush

Optional Accessories:

Some or all of these may have come with your unit. These items are available for purchase. To order replacement parts, additional tools or formulas, please refer to page 17-18.

Multi-Surface Floor Tool

5 Brush
Crevice Tool- (works for wet cleaning too)

Upholstery Dusting Brush

Carpet Deep Cleaning Tool
Quick Dry Hard Floor Tool (Shown with Microfibre Pad) www.bissell.com

4 Upholstery Tool

Drain Cleaner
ug120-4005_7700_607.indd 4

6/28/07 10:05:21 AM

Product view - wet cleaning mode

Solution Tank

Deep Cleaning Floor Nozzle
Keep plenty of genuine BISSELL deep cleaning formulas on hand so you can clean whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas. Non-BISSELL cleaning solutions may harm the machine and void the warranty.

BISSELL Formulas:

These items are available for purchase. To order replacement parts, additional tools or formulas, please refer to page 17-18.
1.42 L 1.42 L Fibre Cleansing Multi- Allergen Formula with Removal Formula Scotchgard with Scotchgard protector protector www.bissell.com
1.42 L Pet Odor and Soil Removal Formula with Scotchgard protector
1.42 L Natural Orange Extract Formula with Scotchgard protector
1.42 L Lavender Essence Formula with Scotchgard protector
.95 L. Hard Floor Solutions Formula

6/28/07 10:05:28 AM

ug120-4005_7700_607.indd 5

How to use this guide

This users guide has been designed to help you get the utmost satisfaction from your BISSELL PROheat All-Rounder. Youll find assembly and operating instructions, safety precautions, as well as maintenance and troubleshooting instructions. Please read this user's guide thoroughly before assembling your product. Pay particular attention to the product diagram, assembly instructions, and part names. Locate and organize all parts before assembly. Familiarize yourself with the parts and where they go. Following this users guide will greatly enhance your ability to get the most performance from your BISSELL PROheat All-Rounder for many years.

WARNING:

Do not plug in your cleaner until you have completely assembled it per the following instructions and are familiar with all instructions and operating procedures.
Your PROheat All-Rounder is easy to assemble and 1 requires no tools: 1. Attach hose to Quick Release Hose Door by inserting fitted end and turning clockwise until you hear it click into the locked position.
Attach hose solution line to unit by inserting fitted end into the machine. Turn clockwise until it snaps into place. Snap the two wand pieces together by lining up tabs with holes and clicking together. Be sure that the wand piece with the adaptor (see figure 4a) is the one you will attach to the tool to. Attached assembled wand to grip using the same technique.
Snap the desired tool on the end of the wand. 4a Place wand adaptor into the wand caddy on the side of the unit. Place either tool caddy or solution tank (if wet clean mode is desired) onto the back of the machine.

Wand Adaptor Wand Caddy

ug120-4005_7700_607.indd 6

6/28/07 10:05:39 AM

Special features of your BISSELL PROheat All-Rounder
Your BISSELL PROheat All-Rounder is a complete home cleaning system. Not only does it come with a lot of unique features, it has been designed with you, the customer, in mind.

Built-in heater

PROheat All-Rounder models all feature a patented built-in heater which heats the hot tap water you put in it up to 25 degrees hotter to safely optimize cleaning effectiveness. The heater will never allow the cleaning solution temperature to exceed 190 degrees. The heater switch on the back of the machine controls the heater so you have the option to turn off the heat if you want to. Microfibre Pad

Top View

Quick dry hard floor tool
BISSELLs unique hard floor tool uses a combination of gentle scrubbing action and strong suction to clean your hard floor surfaces and leave them dry within minutes.
Hard floor Microfibre pad
Soft and gentle microfibre pad is washable and re-usable, time and time again. Bottom View

Tool caddy

The onboard tool caddy can be used to store any tools you are not currently using.

Cleaning tools

Your PROheat All-Rounder comes with a variety of advanced tools, each one just right for a specific job. Some of these tools have multiple uses. Air powered floor TurboBrush: Perfect for carpets and rugs, this air-powered floor TurboBrush comes with an air flow adjustor. When using on normal length carpets and rugs set the selector to Low. For especially thick or long carpet or rugs, switch the selector to High. Additional airflow will be brought in from the top of the brush in the High position.

Selector

800.237.7691
ug120-4005_7700_607.indd 7

6/28/07 10:05:44 AM

Cleaning tools (continued)
Multi-surface floor tool: May be used on both carpet/rugs or hard floor surfaces. For use on carpets, make sure the tab is in the down position. This will hide the soft outer brushes. For hard floor surfaces, press the opposite tab in the down position. This will engage the soft outer brushes. Crevice tool: May be used for both dry vacuuming or wet cleaning.
NOTE: In wet cleaning mode the crevice tool will spray water and cleaning solution. Take care not to press the trigger when in water filtrated vacuum mode.
The handy Quick Release Hose Door ensures that the machines hose never rests on your carpet or hard floors, keeping them clean and dry while filling or emptying the tanks.

Wand caddy

Perfect for storage or when you take a break from cleaning, the wand caddy holds the grip, wands and tools firmly in place

Operation

Vacuuming
Getting Ready Reminder: In order to maximize the cleaning and filtration power of the PROheat All-Rounder and avoid damaging the machine, make sure there is always water in the collection tank. Be sure to fill up to the fill line with clean tap water 1. If desired, make sure the tool caddy is in the back of the machine. Store appropriate vacuuming tools as needed. 2. Attach desired tool to end of wand (or directly to grip).
ug120-4005_7700_607.indd 8

6/28/07 10:05:46 AM

Getting Ready (continued) 3. Remove the collection tank from the unit by opening the Quick Release Hose Door and lifting the tank straight up by the handle.

4. 5. 6. 7. 8. 9.

Remove the top lid from the collection tank and set aside. Fill the collection tank to the fill line (located on side of tank) with clean, cold water. Replace the top lid back onto the top of the collection tank Set the collection tank back in the machine Select "WATER FILTER VACUUM" with the mode selector. Close the Quick Release Hose Door tightly until it clicks into the locked position.
10. Plug into a proper outlet and press the ON/ OFF button down into the ON position.

Emptying the tank 1. Open the Quick Release Hose Door and remove the collection tank by lifting straight up with the tank handle.
Remove the top lid from the collection tank and set it aside. Empty dirty water into a sink or toilet, or outside. Pour the dirty water out from the corner of the tank. Rinse out the tank thoroughly. Refill the tank if needed and replace the top lid back onto the top of the collection tank. Set the collection tank back in the machine. Close Quick Release hose door tightly until it clicks into locked position. If finished vacuuming, refer to the Maintenance and care section starting on page 14.

4. 5. 6. 7.

Wet cleaning
Before you clean 1. Plan activities to give your carpets time to dry. 2. 3. Thoroughly dry vacuum the area to be cleaned. Plan your cleaning route to leave an exit path. It is best to begin cleaning in the corner farthest from your exit.

6/28/07 10:05:48 AM

ug120-4005_7700_607.indd 9
Getting ready to wet clean
NOTE: Remove tool caddy if in place.

1. 2. 3. 4.

Attach the desired wet cleaning tool to end of wand or grip. Open the Quick Release Hose Door and select WET CLEAN with the mode selector. Place the clean solution tank on a flat surface. Fill the solution tank by first unscrewing the measuring cap. Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine. Fill tank to fill line with hot tap water. Add two full measuring caps of formula. Screw measuring cap tightly back onto the solution tank. Place the solution tank back in the machine. Plug into a proper outlet and press the ON/ OFF, wet clean and heater (if desired) buttons down into the ON position.
Note: Allow one minute for the built-in heater to warm up before cleaning. The PROheat All-Rounder will be fully warmed and will provide optimal performance after one minute of continuous heated cleaning.
Move furniture to another area if cleaning an entire room.

Carpet Cleaning 1. Attach carpet deep cleaning tool to end of wand. 2. Place carpet deep cleaning tool directly on carpet. Pull the spray trigger to spray cleaning solution while pulling the wand towards you. Keeping nozzle of the carpet deep cleaning tool firmly against the carpet surface, continue to make slow forward and backward wet passes until no more dirt can be removed. Do not overwet. Release spray trigger and make slow forward and backward passes over the same area to remove any residual dirty water. Repeat wet cleaning passes until water being pulled up appears clean. Continue passes without pressing the spray trigger until you can't see any more water being pulled up.
ATTENTION: a Some Berber carpets have
tendency to fuzz with wear. Repeated strokes in the same area with an ordinary vacuum or deep cleaner may aggravate this condition.
ug120-4005_7700_607.indd 10

6/28/07 10:05:52 AM

Carpet Cleaning (continued) 7. Continue to clean entire carpet working in one meter by one meter sections. 8. If machine loses suction, stop spraying and check the collection tank level. Empty if necessary. If the machine stops spraying turn off wet clean button immediately and check the solution tank level.
NOTE: Never run in wet clean mode when the clean water formula tank is dry or missing.
When you are finished 1. Turn off the heater, wet clean, and power buttons. 2. Remove the collection tank from the unit by opening the quick release hose holder and lifting the tank straight up by the handle. Remove the top lid from the collection tank and set it aside.
Empty dirty water into a sink, toilet or outside. 2 Pour the dirty water out from the corner of the tank. Rinse out the tank thoroughly.
NOTE: You may leave the solution tank with water and formula in it so you are ready for the next use.
Allow all parts to dry before storing.
Hard floor cleaning 1. See Getting Ready to Wet Clean on Page 10. 2. Be sure to use BISSELL Hard Floor Solutions in the solution tank for hard floor cleaning. Fill the formula tank by first unscrewing the measuring cap. Always use genuine BISSELL formulas to maximize cleaning and for the safety of your machine. Fill tank to fill line with hot tap water. Add one full cap of formula. Screw measuring cap tightly back onto the solution tank. Set the solution tank back in the machine.

6/28/07 10:05:56 AM

ug120-4005_7700_607.indd 11
Hard floor cleaning (continued) 4. Attach microfibre pad to quick dry hard floor tool by attaching to the Velcro strips on the top of the tool. 5. 6. 7. Attach the quick dry hard floor tool to end of the wand. Place tool directly on the hard floor surface, resting on the pad. Squeeze the spray trigger to moisten the pad with cleaning solution. Caution: Do not oversaturate. Move the tool back and forth across the floor to clean. Squeeze spray trigger as needed. Tilt the tool forward and pull back. This will create the best suction and will help get the hard floor surface as dry as possible.

10. Continue until room is complete. 11. See When You Are Finished instructions on page 11. 12. Be sure to remove the microfibre pad and clean it by hand or machine wash as needed. Allow it to dry completely before next use. Upholstery cleaning Your PROheat All-Rounder comes with special tools for vacuuming and wet cleaning upholstery, stairs and more. 1. Important! If using to wet clean upholstery, check the upholstery tags proceeding. a. Check manufacturers tag before cleaning. W or WS on the tag means you can use your PROheat All-Rounder. If the tag is coded with an X or an S (with a diagonal stripe through it), or says Dry Clean Only, do not proceed with deep cleaning. Do not use on velvet or silk. If manufacturers tag is missing or not coded, check with the furniture maker or the furniture dealer. b. Check for colourfastness in an inconspicuous place. c. If possible, check upholstery stuffing. Coloured stuffing may bleed through fabric when wet. d. Plan activities to allow upholstery time to dry. e. Vacuum thoroughly.

Manufacturers tag

bvh g kvh gh j j h d b lg fd hn l kl sd jkn f h A d bj jh b j cv hh gcg
ug120-4005_7700_607.indd 12

6/28/07 10:05:59 AM

Upholstery cleaning (continued) 2. Refer to the Getting Ready to Wet Clean on page 10. 3. 4. Attach the desired wet cleaning tool to the wand or grip. Clean by pressing the spray trigger to spray solution onto the area to be cleaned. Slowly move the tool back and forth over the soiled surface. Release the spray trigger to suction soiled water. Continue to clean the area, working in small sections, until no more dirt can be removed. Suction as needed to remove as much water as possible. Caution: Do not overwet. Remove and rinse tools in clean, running water. Dry and put away. See "When you are finished" instructions on page 11.
It is recommended that you suction clean water from the tap to rinse out the hose.

Cleaning fluid section

Keep plenty of genuine BISSELL Formula on hand so you can clean and protect whenever it fits your schedule. Always use genuine BISSELL deep cleaning formulas.
1.42 L Fiber Cleansing Formula with Scotchgard protector item # 710E
1.42 L Multi-Allergen Removal Formula with Scotchgard protector item # 720E
1.42 L Pet Odor and Soil Removal Formula with Scotchgard protector item # 730E
1.42 L Natural Orange Extract Formula with Scotchgard protector item # 740E
1.42 L Lavender Essence Formula with Scotchgard protector item # 750E

6/28/07 10:06:00 AM

ug120-4005_7700_607.indd 13

Maintenance and care

Machine storage
Once your cleaning is complete make sure the dirty water from the collection tank is emptied. Rinsed out and dry before the next use. For wet cleaning, the solution tank can be left filled and ready to use.
Note: Store your PROheat All-Rounder in a protected dry area. Since this product uses water it must not be stored where there is a danger of freezing. Freezing will damage the internal components and void the warranty.

WARNING: To reduce the risk of
fire and electric shock due to internal component damage, use only BISSELL Deep Cleaning Formula intended for use with the deep cleaner. Non-BISSELL cleaning formula may harm the machine and void the warranty.
ug120-4005_7700_607.indd 14

6/28/07 10:06:09 AM

Machine care
For best results, a few simple steps can assure your machine is well maintained after your cleaning is complete. 1. Press all buttons OFF. Unplug the machine and wrap the cord. 2. After emptying the dirty water from the collection tank, rinse it out thoroughly with hot water. Remove all inner parts (water filtration tower and mode selector) if desired. Rinse them and allow to dry before returning into tank.
Note: To remove inner parts, turn mode selector to remove. Pull mode selector straight out towards you. The water filtration tower can now be taken out through the top of the tank.

Water Filtration Tower

Mode Selector
For wet cleaning, remove and clean all tools that were used. Allow to dry before storing. Remove the hose, taking care to keep both ends up to avoid spilling. Dump out any remaining water and flush clean with hot tap water. Allow to dry before storing. a. Pre-motor filter: Take apart the top lid by pulling the tab away from the separator. Inspect the foam filter. If dirty, rinse clean and allow to dry before returning it to the machine. Re-assemble the top lid by placing the filter in its spot and re-attaching the separator. Use care to make sure the T pieces are lined up under the shallow grooves on the top lid itself. For replacement of this part, see pages 18-19. b. HEPA Media filter: This filter is located at the back of the machine, underneath the Quick Release Cord Wrap. Use one finger to depress the latch and pull the door down. Open towards you and down to the ground. Use two hands to remove the filter from its slot. If dirty, rinse clean and allow to dry before returning it to the machine. Make sure the filter door is fully closed prior to operating the machine. For replacement of this filter see pages 18-19.
ug120-4005_7700_607.indd 15

Troubleshooting

WARNING:fire, To reduce the risk of
electric shock or injury unplug from outlet before servicing.

Remedies

Reduce Spray or No Spray

Possible Cause

1. Make sure power is on 2. Solution tank may be empty 3. Tank may not be seated properly 4. Hose solution line may be disconnected 5. Wet clean is not turned on
1. Press power button if needed 2. Fill tank according to directions 3. Turn ON/OFF, heater and wet clean button off. Remove and reseat tank 4. Check connection at front of machine 5. Depress wet clean button to turn on
Machine is not suctioning

Possible Cause Remedies

1. Collection tank may not be placed properly
2. Collection tank may not be assembled properly 3. Wand tool connections are not tight
4. Collection tank is full 5. Float has tripped 6. Pre-motor filter is dirty
1. Open Quick Release Hose Door, lift out tank and re-seat. Re-latch Quick Release Hose Door 2. Check to make sure the top lid is properly seated 3. Check all connections (At grip, wand and tool) Push tight if necessary. 4. Empty collection tank by following instruction on page 9 5. Check to see if tank needs to be emptied. Make sure float is down towards bottom of tank. 6. Remove top lid. Remove and clean pre-moter filter by following instructions on page 15. Filter must be completely dry before using again
Built-in heater light does not illuminate
1. The heater button has not been depressed 2. The ON/OFF button has not been depressed
1. Depress the heater button 2. Depress the ON/OFF button
Other maintenance or service not included in the manual should be performed by an authorized service representative.
Thank you for selecting a BISSELL product.
Please do not return this product to the store.
ug120-4005_7700_607.indd 16

6/28/07 10:06:12 AM

BISSELL Consumer Services
If your BISSELL product should require service:
In the UK, or New Zealand, call BISSELL Consumer Services at the numbers below and we will give you the location of a BISSELL Authorized Service Center in your area. For all other countries, contact your local in country distributor for questions, service, or repair. If you have questions about your warranty or need replacement parts please contact the numbers below.

For UK inquiries: Monday - Thursday 9 am 5 pm Friday 9 am 4 pm BISSELL Homecare (Overseas) Inc. The Boat Yard 105 Straight Road Old Windsor Berkshire, SL4 2SE United Kingdom Telephone: 0870-225-0109
For New Zealand inquiries: Monday - Friday 9 am 5 pm Parex Industries Ltd. 103 Central Park Drive Henderson Auckland New Zealand Telephone: 0800-247-735
For all other inquiries: Monday - Friday 8 am 4 pm BISSELL Homecare, Inc. PO Box 1888 Grand Rapids, MI 49501 USA Telephone: 01-616-453-4451 Fax: 01-616-453-1383
Or visit the BISSELL website - www.bissell.com When contacting BISSELL, have model number of unit available. Please record your Model Number: ___________________ Please record your Purchase Date: ___________________ Note: Please keep your original sales receipt. It provides proof of date of purchase in the event of a warranty claim. See Warranty on page 20 for details. Please do not return this product to the store.

6/28/07 10:06:13 AM

ug120-4005_7700_607.indd 17
Replacement parts - BISSELL PROheat All-Rounder
Below a list of common replacement parts*. While not all of these parts may have come with your specific machine, all are available to you for purchase, if desired.

Item Part No. Part Name

41 203-7063 203-7064 203-7073 203-7066 203-7067 203-7068 203-7069 203-7070 203-7071 203-7072 203-7065 203-7074 203-7076 203-7077 203-7078 203-7079 203-7080 203-7082 203-7083 203-7084 203-7085 203-7086 203-7087 203-7088 203-7089 203-7090 203-7091 203-7092 203-7093 203-7096 203-7097 203-7098 203-7099 203-7100 203-7102 710E 720E 730E 740E 750E 0484 Mulit-Surface Floor Tool Air Powered Floor TurboBrush 5" Brush Wand Adaptor Crevice Tool Upholstery Dusting Brush Carpet Deep Cleaning Tool Carpet Deep Cleaning Tool Brush Strip Carpet Deep Cleaning Tool Adaptor 4" Upholstery Tool Quick Dry Hard Floor Tool (pads not included) Hard Floor Microfibre Pads (2 Pack) Drain Cleaner Tool Caddy Hose Grip Assembly Measuring Cap Pre-Motor Filter HEPA Media Filter Solution Tank Small cap/insert HEPA Filter Door Float Diverter Water Filtration Tower Water Filtration Tower Gasket Separator with Filter Top Lid Assembly Lid Collection Tank Collection Tank Assembly Motor Duct Gasket Quick Release Hose Door Assembly Carry Handle Assembly Caster Wheel 1.42 L Fiber Cleansing Formula with Scotchgard protector 1.42 L Multi-Allergen Removal Formula with Scotchgard protector 1.42 L Pet Odor and Soil Removal Formula with Scotchgard protector 1.42 L Natural Orange Extract Formula with Scotchgard Protector 1.42 L Lavender Essence Formula with Scotchgard protector 0.95 L Hard Floor Solutions

*Not all parts are included with every model.
ug120-4005_7700_607.indd 18

(Pads not included

ug120-4005_7700_607.indd 19
Warranty - BISSELL PROheat All-Rounder
This warranty gives you specific legal rights, and you may also have other rights which may vary from country to country. If you need additional instruction regarding this warranty or have questions regarding what it may cover, please contact BISSELL Consumer Services by telephone, or regular post as described below, or contact your local in country distributor.
Limited Two Year Warranty
Subject to the *EXCEPTIONS AND EXCLUSIONS identified below, BISSELL Homecare, Inc., will replace (with new or remanufactured components), at BISSELLs option, free of charge from the date of purchase by the original purchaser, for two years any defective or malfunctioning part do to manufacturers defect. This warranty applies to product used for personal, and not commercial or rental service. This warranty does not apply to fans or routine maintenance components such as filters, belts, or brushes. Damage or malfunction caused by negligence, abuse, or use not in accordance with the Users Guide is not covered.
BISSELL HOMECARE INC. IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE ASSOCIATED WITH THE USE OF THIS PRODUCT. BISSELLS LIABILITY WILL NOT EXCEED THE PURCHASE PRICE OF THE PRODUCT. *EXCEPTIONS AND EXCLUSIONS FROM THE TERMS OF THE LIMITED WARRANTY THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ANY OTHER WARRANTIES EITHER ORAL OR WRITTEN. ANY IMPLIED WARRANTIES WHICH MAY ARISE BY OPERATION OF LAW, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO THE TWO YEAR DURATION FROM THE DATE OF PURCHASE AS DESCRIBED ABOVE.
2007 BISSELL Homecare, Inc Grand Rapids, Michigan All rights reserved. Printed in China Part Number 120-4005 Rev 6/07 Visit our website at: www.bissell.com Scotchgard is a trademark of 3M
ug120-4005_7700_607.indd 20

6/28/07 10:06:32 AM

PROheatTM Allrounder Model 7700F
Bissell New Zealand Phone: 0800 BISSELL Fax: 520 Email: sales@parex.co.nz Issued: June 2007 Revised: 2007 BISSELL Homecare, Inc.
Bissell Homecare, Inc. (U.S.) Phone: 1-800-457-1509 Fax: 1-800-517-9535 partner.bissell.com

PROheat Allrounder

Model 7700F

KEY 49 XX XX XX XX XX XX

PART NO 2037113
DESCRIPTION MEASURING CAP SOLUTION TANK SMALL CAP/INSERT TANK ASSEMBLY LID SEPARATOR WITH FILTER PRE-MOTOR FILTER TOP LID ASSEMBLY FLOAT WATER FILTRATION TOWER GASKET WATER FILTRATION TOWER DIVERTER COLLECTION TANK COLLECTION TANK ASSEMBLY CARRY HANDLE ASSEMBLY MAIN HOUSING ALLROUNDER RECEIVER VALVE MOTOR DUCT GASKET TOOL CADDY SWITCH COVER, WET CLEAN SWITCH COVER, ON/OFF SWITCH COVER, HEATER CORD WRAP SWITCH, 220V SWITCH, LIGHTED SWITCH ASSEMBLY MOTOR, 220V HEPA FILTER DOOR PUMP, 220V HEPA MEDIA FILTER CARPET DEEP CLEANING TOOL ADAPTOR ADAPTOR WAND (1 PIECE) AIR POWERED FLOOR TURBOBRUSH QUICK DRY HARD FLOOR TOOL CARPET DEEP CLEANING TOOL UPHOLSTERY DUSTING BRUSH CREVICE TOOL 100mm UPHOLSTERY TOOL DRAIN CLEANER MULTI-SURFACE FLOOR TOOL 125mm BRUSH QUICK RELEASE HOSE DOOR ASSEMBLY CASTER WHEEL WHEEL (1 PIECE) HEATER 220V HOSE GRIP ASSEMBLY (HOSE LENGTH NOT TO SCALE) CARPET DEEP CLEANING BRUSH STRIP MESH BAG USERS GUIDE HARD FLOOR MICROFIBRE PADS 2 PK CORD AUSSIE, 5.5 M TUBING 6.8 X 11 SILICON
BISSELL Homecare, Inc. (U.S.)
Issued: July 2007 Revised: July BISSELL Homecare Inc.
Parex Industries Ltd (New Zealand)