www.blackanddecker.co.uk

GL701 GL710 GL716 GL720 GL741

English

(Original instructions)

Intended use

Your Black & Decker trimmer has been designed for trimming and finishing lawn edges and to cut grass in confined spaces. This appliance is intended for consumer use only.

After use

Safety instructions
Warning! When using mains-powered appliances, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material damage. u Read all of this manual carefully before operating the appliance. u The intended use is described in this manual. The use of any accessory or attachment or the performance of any operation with this appliance other than those recommended in this instruction manual may present a risk of personal injury. u Retain this manual for future reference.
When not in use, the appliance should be stored in a dry, well ventilated place out of reach of children. u Children should not have access to stored appliances. u When the appliance is stored or transported in a vehicle it should be placed in the boot or restrained to prevent movement following sudden changes in speed or direction. Before use, check the appliance for damaged or defective parts. Check for breakage of parts and any other conditions that may affect its operation. u Do not use the appliance if any part is damaged or defective. u Have any damaged or defective parts repaired or replaced by an authorised repair agent. u Never attempt to remove or replace any parts other than those specified in this manual.

Inspection and repairs

Using your appliance
Always take care when using the appliance. u Always use safety glasses or goggles. u Never allow children or people unfamiliar with the instructions to use the appliance. u Do not allow children or animals to come near the work area or to touch the appliance or power supply cord. u Close supervision is necessary when the appliance is used near children. u This appliance is not intended for use by young or infirm persons without supervision. u This appliance is not to be used as a toy. u Only use the appliance in daylight or good artificial light. u Use in a dry location only. Do not allow the appliance to become wet. u Do not immerse the appliance in water. u Do not open the body casing. There are not userserviceable parts inside. u Do not operate the appliance in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. u To reduce the risk of damage to plugs or cords, never pull the cable to remove the plug from a socket.
Always use an approved extension cable suitable for the power input of this appliance (see technical data). The extension cable must be suitable for outdoor use and marked accordingly. Up to 30 m of 1.5 mm2 HO5VV-F extension cable can be used without loss of product performance. Before use, inspect the extension cable for signs of damage, wear and ageing. Replace the extension cable if damaged or defective. When using a cable reel, always unwind the cable completely.

Using an extension cable

Additional safety instructions for grass trimmers

Safety of others

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. u Children must be supervised to ensure that they do not play with the appliance.
Warning! Cutting elements continue to rotate after the motor is switched off. u Be familiar with the controls and the proper use of the appliance. u Before use, check the power supply cord and extension cord for signs of damage, ageing and wear. If a cord becomes damaged during use, disconnect the cord from the mains supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. u Do not use the appliance if the cords are damaged or worn. u Wear stout shoes or boots to protect your feet. u Wear long trousers to protect your legs. u Before using the appliance, check that your cutting path is free from sticks, stones, wire and any other obstacles. u Only use the appliance in the upright position, with the cutting line near the ground. Never switch the appliance on in any other position. u Move slowly when using the appliance. Be aware that freshly cut grass is damp and slippery. u Do not work on steep slopes. Work across the face of slopes, not up and down. u Never cross gravel paths or roads while the appliance is running.

Never touch the cutting line while the appliance is running. Do not put the appliance down until the cutting line has come to a complete standstill. u Use only the appropriate type of cutting line. Never use metal cutting line or fishing line. u Be careful not to touch the line trimming blade. u Take care to keep the mains cable away from the cutting line. Always be aware of the position of the cable. u Keep hands and feet away from the cutting line at all times, especially when switching on the motor. u Before using the appliance and after any impact, check for signs of wear or damage and repair as necessary. u Never operate the appliance with damaged guards or without guards in place. u Take care against injury from any device fitted for trimming the filament line length. After extending new cutter line always return the machine to its normal operating position before switching on. u Always ensure that the ventilation slots are kept clear of debris. u Do not use the lawn trimmer (edge trimmer), if the cords are damaged or worn. u Keep extension cords away from cutting elements.
3. Cable restraint 4. Power inlet 5. Secondary handle 6. Adjustment button 7. Tube 8. Guard 9. Line trimming blade 10. Spool housing 11. Cutting line 12. Edge guide

Assembly

Warning! Before assembly, make sure that the appliance is switched off and unplugged.
Fitting the guard (fig. A)

Labels on appliance

Remove the hexagonal screws (13) from the head (14). Place the guard (8) onto the appliance as shown. u Firmly press the guard until it snaps into place. u Secure the guard with the hexagonal screws. u Tighten the hexagonal screws using the hexagonal key (15) provided. Warning! Never use the appliance unless the guard is properly fitted.
The following warning symbols are found on the appliance:
Releasing the cutting line
Read the manual prior to operation. Wear safety glasses or goggles when operating this appliance. Keep people and animals at least 6 m away from the cutting area. Do not expose the appliance to rain or high humidity.
In transit, the cutting line is taped to the spool housing. u Remove the tape holding the cutting line (11) to the spool housing (10).
Connecting the appliance to the mains
Connect the female plug of a suitable extension cable to the power inlet (4). u Loop the cable through the cable restraint (3). u Insert the mains plug into a mains outlet. Warning! The extension cable must be suitable for outdoor use.

Electrical safety This appliance is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.
Warning! Let the tool work at its own pace. Do not overload.
Setting the appliance to trimming or edging mode (fig. B - D)
If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.
The appliance can be used in trimming mode as shown in fig.B or in edging mode to trim overhanging grass along lawn edges and flower beds as shown in fig. C. Trimming mode (fig. B & D) For trimming, the trimmer head should be in the position shown in fig. B. If it is not: u Depress the adjustment button (6). u Rotate the tube (7), while releasing the button. u When the head is in position, the button will lock into place. Note: The tube will only rotate in one direction.

Features

This appliance includes some or all of the following features. 1. On/off switch 2. Handle
Edging mode (fig. C & D) For edging, the trimmer head should be in the position shown in fig. C. If it is not: u Depress the adjustment button (6). u Rotate the tube (7), while releasing the button. u When the head is in position, the button will lock into place. Note: The tube will only rotate in one direction.
Adjusting the height of the appliance (fig. D)
This appliance has a telescopic mechanism, allowing you to set it to a comfortable height. There are three height settings. To adjust the height setting, proceed as follows: u Depress the adjustment button (6). u Gently pull the tube (7) out of the motor housing (16) to the desired height, while releasing the button. u When the tube is in position, the button will lock into place.
Remove any dirt and grass from the spool cover and housing. u Place the new spool onto the boss in the spool housing with the lines parked in the slots (23) (fig. F). u Insert the line ends through the appropriate eyelets (20) in the housing (10). Pull the slack line until it pulls out of the parked slots (23) (fig. G). u Align the tabs (17) on the spool cover with the cut outs (21) in the housing. u Push the cover (18) onto the housing (10) until it snaps securely into place. Note: Make sure that the cover is positioned, listen for two audible clicks to ensure both tabs (17) are correctly located.

Warning! If the cutting lines protrude beyond the trimming blade (9), cut them off so that they just reach the blade.

Switching on and off

Winding new line onto an empty spool (fig. H - J)
To switch the appliance on, squeeze the trigger lever (1). To switch the appliance off, release the trigger lever. Warning! Never attempt to lock the trigger lever in the on position.
Hints for optimum use General
In order to achieve optimum cutting results, only cut dry grass.

Trimming

Hold the appliance as shown in fig. B. Gently swing the trimmer from side to side. u When cutting long grass, work in stages from the top. Take small cuts. u Keep the appliance away from hard objects and delicate plants. u If the appliance starts running slowly, reduce the load.

Edging

Optimum cutting results are achieved on edges deeper than 50 mm. u Do not use the appliance to create edges. To create edges, use an edging spade. u Guide the appliance as shown in fig. C. u To make a closer cut, slightly tilt the appliance.
You may wind new cutting line onto an empty spool. Replacement packs of cutting line are available from your Black & Decker dealer (cat. no. A6171). u Remove the empty spool from the appliance as described above. u Remove any remaining cutting line from the spool. u First wind new line onto the uppermost part of the spool: Feed 2 cm of cutting line into one of the slots in the upper section of the spool as shown. Wind the cutting line onto the spool in the direction of the arrow. Make sure to wind the line on neatly and in layers. Do not criss-cross. When the wound cutting line reaches the recesses (22), cut the line. Temporarily park the line in the slots (23) on one side of the spool as shown. u Repeat the above procedure for the second cutting line on the lower section of the spool. Park the line in the unused slots (23). u Proceed as described above to fit the spool on the appliance. Do not forget to release the cutting line from the parking slots (23). Warning! Only use the appropriate type of Black & Decker cutting line. Ensure that cutting line is present in both sections of the spool.
Mains plug replacement (U.K. & Ireland only)
Fitting a new spool of cutting line (fig. E & G)
Replacement spools of cutting line are available from your Black & Decker dealer (cat. no. A6495). u Keep the tabs (17) depressed and remove the spool cover (18) from the housing (10). u Remove the empty spool (19) from the spool housing.
If a new mains plug needs to be fitted: u Safely dispose of the old plug. u Connect the brown lead to the live terminal in the new plug. u Connect the blue lead to the neutral terminal. Warning! No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local Black & Decker repair agent. Warning! Before proceeding, unplug the tool.
Regularly clean the motor housing using a damp cloth. Do not use any abrasive or solvent-based cleaner. u Regularly open the chuck and tap it to remove any dust from the interior (when fitted).
Protecting the environment

Appliance runs slowly

Check that the spool housing can rotate freely. Carefully clean it if necessary. u Check that the cutting line does not protrude more than 11cm from the spool housing. If it does, cut it off so that it just reaches the line trimming blade.
Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Re-use of recycled materials helps prevent environmental pollution and reduces the demand for raw materials.
Automatic line feed does not work
Keep the tabs depressed and remove the spool cover from the housing. u Pull the cutting line until it protrudes 11 cm from the housing. If insufficient cutting line is left on the spool, install a new spool of cutting line as instructed above. u Align the tabs on the spool cover with the cut outs in the housing. u Push the cover onto the housing until it snaps securely into place. u If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. If the automatic line feed still does not work or the spool is jammed, try the following suggestions: u Carefully clean the spool cover and housing. u Remove the spool and check if the lever can move freely. u Remove the spool and unwind the cutting line, then wind it on neatly again as described above. Replace the spool as instructed.
Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Technical data Input voltage VAC Power input W No-load speed min-1 Weight kg Input voltage VAC Power input W No-load speed min-1 Weight kg GL701 GL710 GL716 TYPE 3-5 TYPE 3-5 TYPE 3-580 6,500 6,500 6,500 3.2 3.2 3.2 GL720 GL741 TYPE 3-5 TYPE 3-6,500 6,500 3.2 3.2

Maintenance

Your Black & Decker corded/cordless appliance/tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance on corded/ cordless power tools: u Switch off and unplug the appliance/tool. u Or switch off and remove the battery from the appliance/ tool if the appliance/tool has a separate battery pack. u Or run the battery down completely if it is integral and then switch off. u Unplug the charger before cleaning it. Your charger does not require any maintenance apart from regular cleaning. u Regularly clean the ventilation slots in your appliance/tool/ charger using a soft brush or dry cloth.
EC declaration of conformity
MACHINERY DIRECTIVE OUTDOOR NOISE DIRECTIVE
GL701/GL710/GL716/GL720/GL741 Black & Decker declares that these products described under "technical data" are in compliance with: 98/37/EC (until Dec. 28, 2009), 2006/42/EC (from Dec. 29, 2009), EN 60335-1, EN 60335-2-91 2000/14/EC, Lawn Mower, L 50 cm, Annex VIII KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem, The Netherlands Notified Body ID No.: 0344 Level of accoustic power according to 2000/14/EC (Article 12, Annex III, (6) L 50 cm): LWA (measure sound power) 95 dB(A) LWA (guaranteed sound power) 96 dB(A) These products also comply with directive 2004/108/EC. For more information, please contact Black & Decker at the following address or refer to the back of the manual.
If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless: u The product has been used for trade, professional or hire purposes; u The product has been subjected to misuse or neglect; u The product has sustained damage through foreign objects, substances or accidents; u Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff. To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk

The undersigned is responsible for compilation of the technical file and makes this declaration on behalf of Black & Decker. Kevin Hewitt Vice-President Global Engineering Black & Decker Europe, 210 Bath Road, Slough, Berkshire, SL1 3YD United Kingdom 8-9-2009 UK patent application no. 059745.6
European Community design application nos.: 340385-0001 & 339544-0001

Guarantee

Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area.
GL701 - GL710 - GL716 - GL720 - GL741
Partial support - Only parts shown available Nur die aufgefuerten teile sind lieferbar Reparation partielle - Seules les pieces indiquees sont disponibles Supporto parziale - Sono disponibili soltanto le parti evidenziate Solo estan disponibles las peizas listadas So se encontram disponiveis as pecas listadas Gedeeltelijke ondersteuning - alleen de getoonde onderdelen zijn beschikbaar

TYP. 3-5

18 800

E15496

www.2helpU.com

28 - 11 - 08

ENGLISH Do not forget to register your product!
www.blackanddecker.co.uk/productregistration Register your product online at www.blackanddecker.co.uk/productregistration or send your name, surname and product code to Black&Decker in your country.
Australia Black & Decker (Australia) Pty. Ltd. 20 Fletcher Road, Mooroolbark, Victoria, 3138 New Zealand Black & Decker 5 Te Apunga Place Mt Wellington Auckland 1060 United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD

Tel. 03-Fax 03-9727 5940

Tel. +Fax +259 1122
Tel. Fax Helpline 01753 574277

90552981

T-09/09

www.blackanddecker.co.uk

Ireland Australia

New Zealand

Intended use
Your Black & Decker strimmer GL701/GL716/GL720/GL741 has been designed for trimming and finishing lawn edges and to cut grass in confined spaces.This tool is intended for consumer use only.
Secure workpiece Use clamps or a vice to hold the workpiece. It is safer and it frees both hands to operate the tool. Connect dust extraction equipment If devices are provided for the connection of dust extraction and collection facilities, ensure that these are connected and properly used. Remove adjusting keys and wrenches Always check that adjusting keys and wrenches are removed from the tool before operating the tool. Extension cables Before use, inspect the extension cable and replace if damaged. When using the tool outdoors, only use extension cables intended for outdoor use. Up to 30 m of Black & Decker extension cable can be used without loss of power. Use appropriate tool The intended use is described in this instruction manual. Do not force small tools or attachments to do the job of a heavyduty tool. The tool will do the job better and safer at the rate for which it was intended. Do not force the tool. Do not use the tool for purposes not intended, for example, do not use a circular saw to cut tree limbs or logs. Warning! The use of any accessory or attachment or performance of any operation with this tool other than those recommended in this instruction manual may present a risk of personal injury. Check for damaged parts Before use, carefully check the tool and mains cable for damage. Check for misalignment and seizure of moving parts, breakage of parts, damage to guards and switches and any other conditions that may affect its operation. Ensure that the tool will operate properly and perform its intended function. Do not use the tool if any part is damaged or defective. Do not use the tool if the switch does not turn it on and off. Have any damaged or defective parts repaired or replaced by an authorised repair agent. Never attempt any repairs yourself. Unplug the tool Unplug the tool when it is not in use, before changing any parts of the tool, accessories or attachments and before servicing. Avoid unintentional starting Do not carry the tool with a finger on the on/off switch. Be sure that the tool is switched off when plugging in.

Safety instructions

Warning! When using mains-powered tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock, personal injury and material damage. Read all of this manual carefully before operating the tool. Retain this manual for future reference. Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.
Keep work area clean Cluttered areas and benches can cause accidents. Consider work area environment Do not expose the tool to rain. Do not use the tool in damp or wet conditions. Keep the work area well lit. Do not use the tool where there is a risk of causing fire or explosion, e.g. in the presence of flammable liquids and gases. Keep children away Do not allow children, visitors or animals to come near the work area or to touch the tool or mains cable. Dress properly Do not wear loose clothing or jewellery, as these can be caught in moving parts. Preferably wear rubber gloves and non-slip footwear when working outdoors. Wear protective hair covering to keep long hair out of the way. Personal protection Always use safety glasses. Use a face or dust mask whenever the operations may produce dust or flying particles. Hearing protection should be worn. Guard against electric shock Prevent body contact with earthed or grounded surfaces (e.g. pipes, radiators, cookers and refrigerators). Electric safety can be further improved by using a high-sensitivity (30 mA / 30 mS) residual current device (RCD). Do not overreach Keep proper footing and balance at all times. Stay alert Watch what you are doing. Use common sense. Do not operate the tool when you are tired.

Do not abuse cord Never carry the tool by its cord or pull it to disconnect from the socket. Keep the cord away from heat, oil and sharp edges. Store idle tools When not in use, tools should be stored in a dry, locked up or high place, out of reach of children. Maintain tools with care Keep cutting tools sharp and clean for better and safer performance. Follow the instructions for maintenance and changing accessories. Keep handles and switches dry, clean and free from oil and grease. Repairs This tool complies with relevant safety requirements. Repairs should only be carried out by qualified persons using original spare parts; otherwise this may result in considerable danger to the user. Electrical safety This tool is double insulated; therefore no earth wire is required. Always check that the power supply corresponds to the voltage on the rating plate.
This appliance is not intended for use by young or infirm persons without supervision. Children must be supervised to ensure they do not play with the appliance. If the supply cord is damaged, it must be replaced by the manufacturer or an authorised Black & Decker Service Centre in order to avoid a hazard.
Additional safety instructions for grass trimmers The following warning symbols are found on the tool:
Before use check the supply and extension cord for any signs of damage or ageing. If the cord becomes damaged during use, disconnect the cord from the supply immediately. DO NOT TOUCH THE CORD BEFORE DISCONNECTING THE SUPPLY. Do not use the lawn trimmer (edge trimmer), if the cords are damaged or worn. Wear stout shoes or boots to protect your feet. Wear long trousers to protect your legs. Before using the tool, check that your cutting path is free from sticks, stones, wire and any other obstacles. Only use the tool in the upright position, with the cutting line near the ground. Never switch the tool on in any other position. Move slowly when using the tool. Be aware that freshly cut grass is damp and slippery. Do not work on steep slopes. Work across the face of slopes, not up and down. Never cross gravel paths or roads while the tool is running. Never touch the cutting line while the tool is running. Do not put the tool down until the cutting line has come to a complete standstill. Use only the appropriate type of cutting line. Never use metal cutting line or fishing line. Be careful not to touch the line trimming blade. Take care to keep the mains cable away from the cutting line. Always be aware of the position of the cable. Keep hands and feet away from the cutting means at all times and especially when switching on the motor. Warning. Cutting elements continue to rotate after the motor is switched off. Never operate the machine with damaged guards or without the guards in place. Always ensure that the ventilation openings are kept clear of debris.

Features

Read the manual prior to operation. Wear safety glasses or goggles when operating this tool.
Keep people and animals at least 6 m away from the cutting area.
Do not expose the tool to rain or high humidity.
Be familiar with the controls and the proper use of the equipment. Only use the machine in daylight or good artificial light.
This tool includes some or all of the following features. 1. On/off switch 2. Handle 3. Cable restraint 4. Power inlet 5. Secondary handle 6. Adjustment button 7. Tube 8. Guard 9. Line trimming blade 10. Spool housing 11. Cutting line 12. Edge guide

6m/20ft

Assembly
Warning! Before assembly, make sure that the tool is switched off and unplugged. Fitting the guard (fig. A) x Remove the Allen screws (13) from the head (14). x Place the guard (8) onto the tool as shown. x Firmly press the guard until it snaps into place. x Secure the guard with the Allen screws. x Tighten the Allen screws using the Allen key (15) provided. Warning! Never use the tool unless the guard is properly fitted. Releasing the cutting line In transit, the cutting line is taped to the spool housing. x Remove the tape holding the cutting line (11) to the spool housing (10). Connecting the tool to the mains x Connect the female plug of a suitable extension cable to the power inlet (4). x Loop the cable through the cable restraint (3). x Insert the mains plug into a mains outlet. Warning! The extension cable must be suitable for outdoor use.
Adjusting the height of the tool (fig. D) This tool has a telescopic mechanism, allowing you to set it to a comfortable height. There are three height settings. To adjust the height setting, proceed as follows: x Depress the adjustment button (6). x Gently pull the tube (7) out of the motor housing (16) to the desired height, while releasing the button. x When the tube is in position, the button will lock into place. Switching on and off x To switch the tool on, squeeze the trigger lever (1). x To switch the tool off, release the trigger lever. Warning! Never attempt to lock the trigger lever in the on position. Hints for optimum use General x In order to achieve optimum cutting results, only cut dry grass. Trimming x Hold the tool as shown in fig. B. x Gently swing the trimmer from side to side. x When cutting long grass, work in stages from the top. Take small cuts. x Keep the tool away from hard objects and delicate plants. x If the tool starts running slowly, reduce the load. Edging Optimum cutting results are achieved on edges deeper than 50 mm. x Do not use the tool to create edges. To create edges, use an edging spade. x Guide the tool as shown in fig. C. x To make a closer cut, slightly tilt the tool.
Warning! Let the tool work at its own pace. Do not overload. Setting the tool to trimming or edging mode (fig. B - D) The tool can be used in trimming mode as shown in fig. B or in edging mode to trim overhanging grass along lawn edges and flower beds as shown in fig. C. Trimming mode (fig. B & D) For trimming, the trimmer head should be in the position shown in fig. B. If it is not: x Depress the adjustment button (6). x Rotate the tube (7), while releasing the button. x When the head is in position, the button will lock into place. Note: The tube will only rotate in one direction. Edging mode (fig. C & D) For edging, the trimmer head should be in the position shown in fig. C. If it is not: x Depress the adjustment button (6). x Rotate the tube (7), while releasing the button. x When the head is in position, the button will lock into place. Note: The tube will only rotate in one direction.

Maintenance

Your tool has been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper tool care and regular cleaning. Warning! Before performing any maintenance, switch off and unplug the tool.
Regularly clean the ventilation slots in your tool using a soft brush or dry cloth. Regularly clean the cutting line and spool using a soft brush or dry cloth. Regularly use a blunt scraper to remove grass and dirt from the underneath of the guard.
Fitting a new spool of cutting line (fig. E & F) Replacement spools of cutting line are available from your Black & Decker dealer (cat. no. A6495). x Keep the tabs (17) depressed and remove the spool cover (18) from the housing (10). x Remove the empty spool (19) from the spool housing. x Remove any dirt and grass from the spool cover and housing. x Take the new spool and push it onto the boss in the spool cover. Rotate the spool slightly until it is seated. x Unclip the end of one of the cutting lines and guide the line into one of the eyelets (20). The line should protrude approx. 11 cm from the spool cover. x Unclip the end of the other cutting line and guide the line into the other eyelet. The line should protrude approx. 11 cm from the spool cover. x Align the tabs (17) on the spool cover with the cut outs (21) in the housing. x Push the cover onto the housing until it snaps securely into place. Warning! If the cutting lines protrude beyond the trimming blade (9), cut them off so that they just reach the blade. Winding new line onto an empty spool (fig. G - I) You may wind new cutting line onto an empty spool. Replacement packs of cutting line are available from your Black & Decker dealer (cat. no. A6171). x Remove the empty spool from the tool as described above. x Remove any remaining cutting line from the spool. x First wind new line onto the uppermost part of the spool: Feed 2 cm of cutting line into one of the slots in the upper section of the spool as shown. Wind the cutting line onto the spool in the direction of the arrow. Make sure to wind the line on neatly and in layers. Do not criss-cross. When the wound cutting line reaches the recesses (22), cut the line. Temporarily park the line in the slots (23) on one side of the spool as shown. x Repeat the above procedure for the second cutting line on the lower section of the spool. Park the line in the unused slots (23). x Proceed as described above to fit the spool on the tool. Do not forget to release the cutting line from the parking slots (23). Warning! Only use the appropriate type of Black & Decker cutting line. Ensure that cutting line is present in both sections of the spool.

Mains plug replacement (U.K. & Ireland only) If a new mains plug needs to be fitted: x Safely dispose of the old plug. x Connect the brown lead to the live terminal in the new plug. x Connect the blue lead to the neutral terminal. Warning! No connection is to be made to the earth terminal. Follow the fitting instructions supplied with good quality plugs. Recommended fuse: 5 A.

Troubleshooting

If your tool seems not to operate properly, follow the instructions below. If this does not solve the problem, please contact your local Black & Decker repair agent. Warning! Before proceeding, unplug the tool. Tool runs slowly x Check that the spool housing can rotate freely. Carefully clean it if necessary. x Check that the cutting line does not protrude more than 11 cm from the spool housing. If it does, cut it off so that it just reaches the line trimming blade. Automatic line feed does not work x Keep the tabs depressed and remove the spool cover from the housing. x Pull the cutting line until it protrudes 11 cm from the housing. If insufficient cutting line is left on the spool, install a new spool of cutting line as instructed above. x Align the tabs on the spool cover with the cut outs in the housing. x Push the cover onto the housing until it snaps securely into place. x If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade. If the automatic line feed still does not work or the spool is jammed, try the following suggestions: x Carefully clean the spool cover and housing. x Remove the spool and check if the lever can move freely. x Remove the spool and unwind the cutting line, then wind it on neatly again as described above. Replace the spool as instructed.
Protecting the environment
Separate collection. This product must not be disposed of with normal household waste.
Should you find one day that your Black & Decker product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again. Reuse of recycled materials helps prevent environmental pollution and reduces the demand for raw materials. Local regulations may provide for separate collection of electrical products from the household, at municipal waste sites or by the retailer when you purchase a new product. Black & Decker provides a facility for the collection and recycling of Black & Decker products once they have reached the end of their working life. To take advantage of this service please return your product to any authorised repair agent who will collect them on our behalf. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Technical data Voltage Power input No-load speed Weight VAC W min-1 kg GL550 6,500 3.2 GL600 6,500 3.2 GL580 6,500 3.2 GL700 6,500 3.2

EEC declaration of conformity
GL701/GL716/GL720/GL741 Black & Decker declares that these products conform to: 98/37/EC, 89/336/EEC, 73/23/EEC, EN 60335, EN 55014, EN 61000, 2000/14/EC, Annex VIII, Lawn trimmer, L 50 No. 0344, KEMA Quality B.V., Utrechtseweg 310, 6802 ED Arnhem, The Netherlands Level of sound pressure, measured according to 2002/14/EC: LpA (sound pressure) 81 dB(A), LWA (acoustic power) 95 dB(A), LWA (guaranteed) 96 dB(A) Hand/arm weighted vibration value according to EN 786: 7,5 m/s2 Kevin Hewitt Director of Consumer Engineering Spennymoor, County Durham DL16 6JG, United Kingdom 1-11-2005 UK patent application no. 059745.6 European Community design application nos. 340385-0001 & 339544-0001

Guarantee

Black & Decker is confident of the quality of its products and offers an outstanding guarantee. This guarantee statement is in addition to and in no way prejudices your statutory rights. The guarantee is valid within the territories of the Member States of the European Union and the European Free Trade Area. If a Black & Decker product becomes defective due to faulty materials, workmanship or lack of conformity, within 24 months from the date of purchase, Black & Decker guarantees to replace defective parts, repair products subjected to fair wear and tear or replace such products to ensure minimum inconvenience to the customer unless: x The product has been used for trade, professional or hire purposes; x The product has been subjected to misuse or neglect; x The product has sustained damage through foreign objects, substances or accidents; x Repairs have been attempted by persons other than authorised repair agents or Black & Decker service staff.
Voltage Power input No-load speed Weight

VAC W min-1 kg

To claim on the guarantee, you will need to submit proof of purchase to the seller or an authorised repair agent. You can check the location of your nearest authorised repair agent by contacting your local Black & Decker office at the address indicated in this manual. Alternatively, a list of authorised Black & Decker repair agents and full details of our after-sales service and contacts are available on the Internet at: www.2helpU.com Please visit our website www.blackanddecker.co.uk to register your new Black & Decker product and to be kept up to date on new products and special offers. Further information on the Black & Decker brand and our range of products is available at www.blackanddecker.co.uk
GL701 - GL716 - GL720 - GL741

E14605

www.2helpU.com

20-10-05

Australia Black & Decker (Australia) Pty. Ltd. Tel. 03-20 Fletcher Road, Mooroolbark, Fax 03-Victoria, 3138 New Zealand Black & Decker 81 Hugo Johnston Drive Penrose, Auckland, New Zealand United Kingdom Black & Decker 210 Bath Road Slough, Berkshire SL1 3YD Tel. 7600 Fax 8200
Tel. Fax Helpline 01753 574277

496078-00