BA_BahamasMP46_EN.indd 4

4/5/06 9:00:18 AM
Selecting 12/24-hour clock mode. 25 Displaying the time continuously when the device is off and the ignition is on.. 25 Briey displaying time with switched-off device. 25 Sound.. 26 Adjusting the bass.. 26 Adjusting the middle.. 26 Adjusting the treble. 26 Setting the left/right volume distribution (Balance).. 27 Adjusting the front/rear volume distribution (Fader). 27 Preamplier output (Preamp-Out/ Sub-Out)... 27 Adjusting the sub-out level. 27 Adjusting the sub-out cutoff frequency.. 27 X-BASS.. 28 Adjusting the X-BASS boost. 28 Equalizer presettings (Presets). 29 Adjusting the display settings. 29 Entering a switch-on message.. 29 Adjusting the display brightness. 30 Setting the viewing angle. 30 Setting a positive or negative display.. 30 Setting the display illumination colour.. 31 External audio sources. 32 Switching the AUX input on/off. 32 Adjusting the AUX preamplication. 33 Technical Data.. 34 Amplier.. 34 Tuner.. 34 CD.. 34 Pre-amp Out.. 34 Input sensitivity.. 34

BA_BahamasMP46_EN.indd 5

Installation instructions.. 195

Notes and accessories

Thank you for choosing a Blaupunkt product. We hope you enjoy using this new piece of equipment. Please read these operating instructions before using the equipment for the rst time.

Accessory

Remote control Remote control RC-12H included. You can operate all basic functions of your car radio safely and comfortably by means of the remote control. You cannot switch the device on or off with the remote control.
International telephone information
If you have any questions regarding the operation of your car radio or if you require further information, please do not hesitate to call us! The information hotline numbers are printed on the last page of these instructions.

Optional equipment

(not part of the scope of delivery) Use only accessories approved Blaupunkt. by
Amplier You can use all Blaupunkt and Velocity ampliers. CD changers You can connect the following Blaupunkt CD changers: CDC A 03, CDC A 08 and IDC A 09.

Road safety

Road safety has absolute priority. u Only operate your car sound system if the road and trafc conditions allow you to do so. u Familiarise yourself with the device before setting off on your journey. You should always be able to hear police, re and ambulance sirens in good time from inside your vehicle. u For this reason, listen to your car sound system at a suitable volume level during your journey.

Installation

If you want to install your car sound system yourself, please read the installation and connection instructions that follow these operating instructions.

BA_BahamasMP46_EN.indd 6

Control panel

Theft protection

The device is equipped with a detachable control panel (Flip-Release Panel) as a way of protecting your equipment against theft. The device is worthless to a thief without this control panel. Protect your device against theft by taking the control panel with you whenever you leave your vehicle. Do not leave the control panel inside your vehicle - not even in a hiding place. Notes: Never drop the control panel. Never expose the control panel to direct sunlight or other heat sources. Avoid direct skin contact with the control panels electrical contacts. If necessary, please clean the contacts with a lint-free cloth moistened with cleaning alcohol.
Notes: The device is switched off after a time preset by you. For instructions, please read the section Switch-offtime (OFF TIMER) in this chapter. All the current settings are saved. Any CD already inserted in the device remains there.
Attaching the control panel
u Hold the control panel approximately at a right angle to the device. u Slide the control panel into the devices guides that are positioned on the left and right at the lower edge of the housing. Push the control panel carefully into the bracket until it clicks into place. u Carefully ip up the control panel until it clicks into place.
Detaching the control panel
u Press the button 2. The control panel opens out towards you. u Hold the control panel by its right side and then pull the control panel straight out of the bracket.
If the device was still switched on when you detached the control panel, it will automatically switch on with the last setting activated (Radio, CD, CD changer or AUX) when the panel is replaced. 7

BA_BahamasMP46_EN.indd 7

4/5/06 9:00:19 AM

Detachable control panel

Switching on/off
Switch-off time (OFF TIMER)
After opening the control panel, the device is switched off after an adjustable time. You can set this time from 0 to 30 seconds. u Press the MENU button 9. u Press the or button : repeatedly until VARIOUS MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until OFF TIMER appears on the display. u Adjust the time by pressing the or buttons :. When you have nished making your changes, u Press the MENU button 9 three times. Note: If you set the switch-off time to 0 seconds, the device is switched off immediately after opening the control panel.
There are various ways of switching the device on/off: Switching on/off using button 1 u To switch on the device, press button 1. The device switches on. u To switch off the device, press and hold down button 1 for longer than 2 seconds. The device switches off. Switching on/off using the vehicle ignition The device will switch on/off simultaneously with the ignition if the device is correctly connected to the vehicles ignition as shown in the installation instructions and you did not switch the device off by pressing button 1. Switching the device on/off using the detachable control panel u Detach the control panel. The devices switches off after the time set in the OFF TIMER menu. u Attach the control panel again. The device switches on. The last setting (Radio, CD, CD changer or AUX) is reactivated. Note: To protect the vehicle battery, the device will switch off automatically after one hour if the ignition is off.

BA_BahamasMP46_EN.indd 8

Volume
You can adjust the volume in increments from 0 (off) to 66 (maximum). To increase the volume, u Turn the volume control 3 clockwise. To decrease the volume, u Turn the volume control 3 counterclockwise.
Setting the power-on volume
Note: The device features a time-out function (time window). For example, if you press the MENU button 9 and select a menu item, the device switches back after approx. 8 seconds after the last button activation. The settings performed are saved. You can set the power-on volume. u Press the MENU button 9. u Press the or button : repeatedly until VOLUME MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until ON VOLUME appears on the display. u Adjust the power-on volume with the or button :. To help you adjust the setting more easily, the device will increase or decrease the volume as you make your changes. If you enable LAST VOL, the volume which was set the last time you switched off the device is re-enabled.
Quickly reducing the volume (Mute)
You can quickly reduce the volume to a preset level (Mute). u Briey press button 1. MUTE appears on the display. Cancelling mute To return to your previously set volume level, u Briey press button 1 again. Adjusting the mute level You can adjust the mute level. u Press the MENU button 9. u Press the or button : repeatedly until VOLUME MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until MUTE LVL appears on the display. u Adjust the mute level by pressing the or button :. 9

BA_BahamasMP46_EN.indd 9

Adjusting the volume
Note: To protect your hearing, the power-on volume is limited to the value 38. If the volume before switching off was higher and the LAST VOL setting was selected, the device switches on again with the value 38. When you have nished making your changes, u Press the MENU button 9 three times.
When you have nished making your changes u Press the MENU button 9 three times.
Note: Using the volume control 3, you can adjust the volume for telephone calls and voice output directly during the playback.
Telephone Audio/Navigation Audio
If your car sound system is connected with a cell phone or navigation system, the car sound system is muted when you pick up the phone or during a voice output of the navigation and the call or the voice output is played back via the car sound speaker system. For this purpose, the cell phone or the navigation system must be connected to the car sound system as described in the installation instructions. Your Blaupunkt dealer can provide you with the information which navigation system can be used with your car sound system. You can adjust the volume with which you switch on the telephone calls or the voice output of the navigation. u Press the MENU button 9. u Press the or button : repeatedly until VOLUME MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until TEL VOL appears on the display. u Set the desired volume with the or button :. When you have nished making your changes, u Press the MENU button 9 three times. 10

Switching the conrmation beep on/off
The system will output a conrmation beep for some functions if you keep a button pressed down for longer than 2 seconds, for instance, when assigning a radio station to a station preset button. You can switch the beep on or off. u Press the MENU button 9. u Press the or button : repeatedly until VOLUME MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until BEEP ON or BEEP OFF appears on the display. u Switch the BEEP ON or OFF with the or button :. When you have nished making your changes, u Press the MENU button 9 twice.
BA_BahamasMP46_EN.indd 10

Radio mode

This function automatically adjusts the volume of the car sound system to the vehicle speed. For this purpose, the car sound system must be connected as described in the installation instructions. You can adjust the automatic sound in 6 increments from (0 - 5). u Press the MENU button 9. u Press the or button : repeatedly until VOLUME MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until AUTO SD appears on the display. u Set the automatic sound 0 - 5 with the or button :. When you have nished making your changes, u Press the MENU button 9 three times. Note: Your optimal setting of 0 - 5 of the speed-dependent sound adjustment depends upon the driving noise development of your vehicle. Determine the perfect value for your vehicle using trial and error.

Adjusting the tuner

To ensure proper functioning of the tuner, the device must be set for the region in which it is being operated. You can select among Europe (EUROPE), America (USA), South America (S-AMERICA), and Thailand (THAI). The tuner is factory-set to the region in which it was sold. If you experience problems with your radio reception, please check this setting. The radio functions described in these operating instructions refer to the tuner setting America (USA). u Switch off the device by pressing button 1. u Hold the 1 and 5 buttons ; pressed at the same time and switch on the device again with the button 1. TUNER is displayed. u Select your tuner region with the or button :. To save the setting, u Switch the device off and on again or wait approx. 8 seconds. The radio starts playing with the last setting selected (Radio, CD, CD changer or AUX).

Switching to radio mode

If you are in CD, CD changer or AUX mode, u Press the BNDTS button 6. or u Press the SOURCE button 4 repeatedly until the memory bank, e.g. FM1, appears on the display.
BA_BahamasMP46_EN.indd 11

Automatic Sound

Selecting the waveband/memory bank
This device can receive programmes broadcast over the FM and AM frequency ranges. There are three memory banks available for the FM waveband (FM1, FM2 and FMT) and one for the AM waveband. Six stations can be stored in each memory bank. To switch between the memory banks FM1, FM2 and FMT and the AM waveband, u Briey press the BNDTS button 6.

Setting the sensitivity of station seek tuning
You can choose whether the radio should only tune into stations providing good reception or whether it can also tune into those with a weak reception. u Press the MENU button 9. u Press the or button : repeatedly until TUNER MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until SENS HI or SENS LO appears on the display. SENS HImeans a high sensitivity setting and SENS LOmeans a low sensitivity setting. u Set the desired sensitivity level using the or button :. When you have nished making your changes, u Press the MENU button 9 twice. Note: The device will store the sensitivity setting selected in FM and AM waveband.

Tuning into a station

There are various ways of tuning into a station. Automatic station seek tuning u Press the or button :. The radio tunes into the next receivable station. Tuning into stations manually You can also tune into stations manually. To change the set frequency in small increments, u Briey press the or button :. To change the set frequency quickly, u Press and hold down the or button : for a longer period of time.
BA_BahamasMP46_EN.indd 12

4/5/06 9:00:20 AM

Storing stations manually u Select the desired memory bank (FM1, FM2, FMT) or the wavebands AM. u Tune into the desired station. u Press and hold down one of the station 16 buttons ; for longer than 2 seconds to assign the station to that button.
Scanning receivable stations (SCAN)
You can use the scan function to play all the receivable stations briey. You can set the scanning time in the menu to between 5 and 30 seconds. Starting SCAN u Press and hold down the MENU button 9 for longer than 2 seconds. Scanning begins. SCAN appears briey in the display followed by a ashing display of the current station name or frequency. Cancelling the SCAN and continuing to listen to a station u Press the MENU button 9. Scanning stops and the radio continues playing the station that it tuned into last.
Storing stations automatically (Travelstore)
You can automatically store the six stations offering the strongest reception in the region. The stations are stored in the FMT or AM memory bank, depending on preset waveband. Note: Any stations that were previously stored in this memory bank are deleted in the process. u Choose the frequency range, for which you would like to set up a Travelstore. u Press and hold down the BNDTS button 6 for longer than 2 seconds. The storing procedure begins. FM TRAVELSTORE or AM TRAVELSTORE appears on the display. After the process has completed, the radio will play the station stored in memory location 1 of the previously selected memory bank.

Random track play (MIX)

u Press the 5 MIX button ;. MIX DISC appears briey on the display and the MIX symbol is displayed. The next randomly selected track will then be played. Cancelling MIX u Press the 5 MIX button ; again. MIX OFF appears briey on the display and the MIX symbol disappears.

Scanning tracks (SCAN)

You can scan (briey play) all the tracks on the CD. u Press the MENU button 9 for longer than 2 seconds. SCAN DISC apears briey on the display, and the next track will then be scanned. Note: You can set the scanning time. For further information, please read the section entitled Setting the scanning time in the Radio mode chapter.

Selecting tracks

u Press one of the arrow buttons : to select the next or previous track. If you press the or button : once, the player will play the current track again from the beginning.

Fast track selection

To quickly select tracks backwards or forwards, u Press and hold down the or button : until fast track selection backwards / forwards begins.
BA_BahamasMP46_EN.indd 15

Fast searching (audible)

Cancelling Scan and continuing listening to a track To end the scanning process, u Press the MENU button 9. The currently scanned track will then continue to be played normally.
You can select from several display types for CD mode: Normal Mode: First line: Track number and playing time Info Mode: First line: Track number and playing time Second line: CD-Text Clock Mode: First line: Track number and playing time Second line: CD text and time Notes: You can decide via Menu, whether the CD text should be displayed. For more information please read the section Displaying CD text. The CD text can only be displayed if the relevant information is available on the CD. To switch between displays, button 8 either u Press the DISPL once or repeatedly, until the display of your choice appears.
Repeating tracks (REPEAT)
If you want to repeat a track, u Press the 4 RPT button ;. REPEAT TRACK appears briey on the display and REPEAT is displayed.The track is repeated until you deactivate Repeat. Cancelling repeat If you want to cancel the repeat function, u Press the 4 RPT button ; again. REPEAT OFF appears briey on the display and REPEAT disappears. Normal playback is then resumed.

D01 D02 D03 T001 T002 T003 T004 T005 T001 T002 T003 T004 T005 T006 D04 T001 T002 T003 T004 T005 T006 T007 T008 T009 T010 T011 A
If you like your les to be in the correct order, you should use burner software that places les in alphanumerical order. If your software does not provide this feature you also have the option of sorting the les manually. For this purpose, you must enter a number in front of each le name, e.g. 001, 002, etc. The leading zeros must also be entered. MP3 tracks can contain additional information such as the artist, album and track names (ID3 tags). This device can display ID3 tags (version 1). When creating (encoding) MP3 les from audio les, you should use bit rates up to a maximum of 256 Kbit/sec. This device can only play MP3 les that have the.MP3 le extension. Notes: To ensure uninterrupted playback, Do not try changing the le extension to.MP3 of any les other than MP3 les and then attempt to play them! The device will ignore these invalid les during playback. Do not use mixed CDs containing both non-MP3 data and MP3 tracks (the device only reads MP3 les during MP3 playback). Do not use mix-mode CDs containing both CD-audio tracks and MP3 tracks. If you try playing a mix-mode CD, the device will only play the CDaudio tracks.
A Directories B Title Files You can name each directory using a PC. The device is capable of displaying the directory name. Name the directories and tracks/les using your CD burner software. The softwares instruction manual will provide details on how to do this. Note: When naming directories and tracks/ les you should avoid using accents and special characters.
BA_BahamasMP46_EN.indd 18

4/5/06 9:00:21 AM

MP3 mode is activated in the same way as normal CD mode. For further information, please read the section entitled Switching to CD mode in the CD mode chapter.
Conguring the default display You can display various types of information on the current track: 1. Normal Mode: First line: Track name Second line: MP3 data Note: MP3 data content depends on the settings in the menu MP3 DISP. 2. Info Mode: First line: Track name Second line: Directory number, track number and playing time 3. Clock Mode: First line: Track name Second line: Directory number, track number and clock Note: MP3 ID tags version 1 can be displayed, if they were stored with the MP3 data les. For more information please read the instructions regarding your MP3 software for PC or your CD burning software. 4. MP3 Browse Mode: First line: Track name 1 Second line: Track name 2 Third line: Track name 3

Adjusting the bass

You can select 1 of 4 centre frequencies (60 Hz, 80 Hz, 100 Hz, 200 Hz). In addition, you can adjust the level between 7 for the selected centre frequency. Adjusting centre frequency and level u Press the AUDIO button 5. BASS appears on the display. u Press the or button : once to reach the BASS submenu. u Press the or button : repeatedly until the desired centre frequency appears on the display. u Press the or button :, to adjust the level between 7. u Press the AUDIO button 5 twice to exit the menu.

Adjusting the treble

You can select 1 of 4 centre frequencies (10 kHz, 12 kHz, 15 kHz, 17 kHz). In addition, you can adjust the level between 7 for the selected centre frequency. Adjusting centre frequency and level u Press the AUDIO button 5. BASS appears on the display. u Press the or button : repeatedly until TREBLE appears on the display. u Press the or button : once to reach the TREBLE submenu.
BA_BahamasMP46_EN.indd 26

Preamplier output

u Press the or button : repeatedly until the desired centre frequency appears on the display. u Press the or button : to adjust the level between 7. u Press the AUDIO button 5 twice to exit the menu.
Setting the left/right volume distribution (Balance)
To adjust the left/right volume distribution (Balance), u Press the AUDIO button 5. BASS appears on the display. u Press the or button : repeatedly until BAL appears on the display with the current setting. u Press the or button : to adjust the balance (right/left). u Press the AUDIO button 5 to exit the menu.
You can use the preamplier outputs (Preamp-Out) of the car sound system to connect external ampliers. In addition, you can connect an amplier for operating a subwoofer to the integrated dynamic lowpass lter of the device (level and cutoff frequency can be adjusted). For this purpose, the ampliers must be connected as described in the installation instructions.
Adjusting the sub-out level
The sub-out level can be adjusted in 8 increments (0 to +7). u Press the AUDIO button 5. BASS appears on the display. u Press the or button : repeatedly until SUBOUT appears on the display. u Press the or button : to adjust a value between 0 and +7. When you have nished making your changes, u Press the AUDIO button 5 twice.

BA_BahamasMP46_EN.indd 29
Equalizer presettings (Presets)
Adjusting the display settings
Adjusting the display brightness
If your car sound system is installed as described in the installation instructions and your vehicle features the corresponding connection, the display brightness is switched with the driving lights. The display brightness can be adjusted separately for day and night in increments from 1 - 9. In addition, you can select the AUTO DIM setting for the night dimmer (DIM NIGHT). After selecting the AUTO DIM setting, the illumination of the car sound system is adjusted together with the brightness adjustment of the instrumentation lighting if the vehicle lighting is switched on. u Press the MENU button 9. u Press the or button : repeatedly until DISPLAY MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until DIM DAY or DIM NIGHT appears on the display. button : to open the u Press the menu. u Press the or button : to select among the brightness settings. When you have nished making your changes, u Press the MENU button 9 twice. To enable AUTO DIM, u Press the or button : repeatedly until DIM NIGHT appears on the display.
button :, until AUTO u Press the DIM is displayed. When you have nished making your changes, u Press the MENU button 9 three times.
Setting the viewing angle
You can set the viewing angle to adjust the device to the mounting position within your vehicle. u Press the MENU button 9. u Press the or button : repeatedly until DISPLAY MENU appears on the display. button : to open the u Press the menu. u Press the or button : repeatedly until VIEW ANGLE appears on the display. button : to open the u Press the menu. u Press or button : to set up the viewing angle. When you have nished making your changes, u Press the MENU button 9 three times.
Setting a positive or negative display
You can decide, whether display contents should be viewed in positive or negative mode. u Press the MENU button 9.
BA_BahamasMP46_EN.indd 30

BA_BahamasMP46_EN.indd 32

4/5/06 9:00:24 AM

Note: If the AUX input is switched on, you can select it by pressing the SOURCE button 4.
Adjusting the AUX preamplication
To be able to adjust for differences in volume, the level adjustment of the AUX input can be adjusted in 4 increments (0 to 3). u Press the MENU button 9. u Press the or button : repeatedly until AUX MENU appears on the display button : to open the u Press the menu. u Press the or button : repeatedly until AUX LVL appears on the display. button : to open the u Press the menu. u Press the or button : to adjust the level adjustment. When you have nished making your changes, u Press the MENU button 9 three times.
BA_BahamasMP46_EN.indd 33

Technical Data

Amplier
Output power: 18W RMS x 4ch @ 14.4V @ 4ohm @ 1% THD
Frequency ranges USA: FM: 87.5 - 107.9 MHz (200 kHz step) AM: 530 - 1710 kHz (10 kHz step) Frequency ranges Europe: FM: 87.5 - 108 MHz (100 kHz step auto/50 kHz manual) AM: 531 - 1602 kHz (9 kHz step) Frequency ranges Thailand: FM: 87.5 - 108 MHz (50 kHz step auto/25 kHz step manual) AM: 531 - 1602 kHz (9 kHz step) Frequency ranges South America: FM: 87.5 - 107.9 MHz (100 kHz step auto/50 kHz step manual) AM: 530 - 1710 kHz (10 kHz step) FM mono sensitivity: 17 dbf FM frequency response: 35 - 16,000 Hz
Frequency response: 20 - 20,000 Hz

Pre-amp Out

4 channels: 2V

Input sensitivity

AUX input: 2 V / 6 k Subject to changes! 34
BA_BahamasMP46_EN.indd 34

lments de commande

1 Touche marche/arrt Pression brve: Coupure du son (Mute) de lappareil. Pression longue: Eextinction de lappareil. 2 Touche - permettant douvrir la faade basculante dtachable (FlipRelease-Panel).
< Touche (Eject) pour le retrait du CD de lappareil.
3 Bouton de rglage du volume 4 Touche SOURCE pour slectionner entre Radio, CD, Changeur de CD (si connect) et AUX. 5 Touche AUDIO pour le rglage de basses, aigus, mdiums, Sub-Out, balance et fader et slection dun prrglage dgaliseur. 6 Touche BNDTS Pression brve: Choix des niveaux de mmoire FM et des gammes dondes AM. Pression longue: Activation de la fonction Travelstore. 7 Touche X-BASS pour le rglage de lafonction X-BASS. 8 Touche DISPL Pression brve: afcher brivement les contenus dafchage alternatifs (p. ex. lheure). Pression longue: changer de contenu dafchage. 9 Touche MENU Pression brve: appel du menu pour les rglages de base. Pression longue: activation de la fonction de balayage (Scan). : Bloc de touches de direction ; Bloc de touches 1 - 6 35

4/5/06 8:58:42 AM

FM FM FM1 AM FM1 u FM2
AM FMT u MENU MENU u u HI SENS LO SENS HI SENS LO : : SENS 9 : TUNER u

FM2 BNDTS

9 FM AM
BA_BahamasMP46_CH.indd 140

4/5/06 8:58:43 AM

u FMT u u 2 AM

MENU SCAN FMT AM u MENU

u u BNDTS
Travelstore 62 u u MENU u u TIME u : : : SCAN MENU 9 : VARIOUS
FM TRAVELSTORE TRAVELSTORE
BA_BahamasMP46_CH.indd 141

4/5/06 8:58:44 AM

CD CD-R 12 CD-RW CD 16 CD

u 2 DISPL CD CD CD CD CD

CD Blaupunkt

CD CD CD MP3 WMA MP3 WMA

CD u u 2 CD
BA_BahamasMP46_CH.indd 142

4/5/06 8:58:45 AM

CD CD u CD CD 5 MIX u MIX DISC MIX ; u :

CD 1 CD u SOURCE 4 CD

MIX u 5 MIX MIX OFF MIX
CD u u : : u MENU SCAN DISC 92
BA_BahamasMP46_CH.indd 143

4/5/06 8:58:46 AM

CD u MENU 9 CD REPEAT CD CD 4 RPT ; u REPEAT OFF REPEAT u CD CD CD

REPEAT

u 4 RPT ; R E P E AT T R AC K

3 ; u PAUSE DISC

CD 3 ; CD
BA_BahamasMP46_CH.indd 144

4/5/06 8:58:47 AM

MP3/WMA
CD MENU 9 : MENU : : TEXT : TEXT ON : CD TEXT OFF 9 CD CD VARIOUS
MP3 WMA WMA DRM WMA WMA CD-R CD-RW MP3

Windows Media-Player 8

u u CD u CD CD CD < CD CD CD

MP3 CD

CD CD 2 Joliet CD ISO 9660

CD 1 CD 252

CD CD 255 CD 999 MP3
BA_BahamasMP46_CH.indd 145

4/5/06 8:58:48 AM

ISO 9660 8

MP3 ID3

IDMP3 256.MP3

MP3.MP3

A B MP3 CD MP3 CD MP3 MP3 CD CD CD MP3 CD
BA_BahamasMP46_CH.indd 146

4/5/06 8:58:50 AM

MP3 CD CD CD MP3 CD MIX MP3 u DISPL MP3 SCAN REPEAT
1. MP3 MP3 MP3 2. MP3 DISP DIR NAME SONG NAME ALBM NAME ARTIST FILE NAME MP3-ID 1 MP3 MP3 ID 1 MP3 MP3 4. MPCD MP3
BA_BahamasMP46_CH.indd 147

9 : VARIOUS MP3

u u DISP u u

: : : : MP3 CD MP3

9 u 8 MP3 MP3 DISPL

MP3 DISP MP3/WMA

CD u u : : CD
BA_BahamasMP46_CH.indd 148

4/5/06 8:58:51 AM

u u : : u

5 MIX MIX DIRECTORY MIX

MP3 CD 5 MIX MIX DISC MIX MIX MIX u MIX OFF MIX 5 MIX ; ;2

DISPL MP3 :

MP3 MP3 u : u MENU SCAN 92 CD
BA_BahamasMP46_CH.indd 149

4/5/06 8:58:52 AM

(PAUSE)

: . (OFF TIMER) . . CD .

u . u . u .

u 2 . . u .
, ( ,CD, CD AUX) . 167

(OFF TIMER) )

, . . u MENU 9 . u VARIOUS MENU : . u : . u OFF TIMER : . u : . , u MENU 9 . : 0 , .
/ : 1 / u 1 . . u , . . / , 1 , / . / u . OFF TIMER . u . . (, CD, CD AUX) . : , .
0() 66() . , u 3 . , u 3 .
: - ( ). , MENU 9 , 8 . . . u MENU 9 . u VOLUME MENU : . u : . u ON VOLUME : . u : . , . LAST VOL , .
: 38 . ,LAST VOL 38. , u MENU 9 .
() u 1 . MUTE. , u 1 . . u MENU 9 . u VOLUME MENU : . u : . u MUTE LVL : . u : . 169

, u MENU 9 .

, . , . Blaupunkt . . u MENU 9 . u VOLUME MENU : . u : . u TEL VOL : . u : . , u MENU 9 . 170

: 3 .

, 2 . . u MENU 9 . u VOLUME MENU : . u : . u BEEP ON BEEP OFF : . u : BEEP ON OFF . , u MENU 9 .
. , . 6 (0 5). u MENU 9 . u VOLUME MENU : . u : . u AUTO SD : . u : . , u MENU 9 . : (0 - 5) . .
, . (EUROPE), (USA), (S-AMERICA) (THAI) . . . (USA) . u 1 . u ; 1 . TUNER. : u . , u 8 . ( , CD, CD AUX).
CD, CD AUX , u BNDTS 6 u FM1 SOURCE 4 . 171
FM AM . FM (FM1, FM2 FMT) AM . . FM1, FM2 FMT AM , u BNDTS 6 .
. u MENU 9 . u TUNER MENU : . u : . u SENS HISENS LO : . SENS HI SENS LO . u : . , u MENU 9 . : FM AM .
. : . u . . , : u. , : u .
u (FM1, FM2, FMT) AM . u . u ; 2 , .

(SCAN) )

. 5 30 . (SCAN) ( ) u MENU . . SCAN . u MENU 9 . .
. FMT AM . : . u . u BNDTS . . FM TRAVEL STOREAM TRAVEL STORE. , 1 .
u MENU 9 . u VARIOUS MENU : . u : . u SCAN TIME : . u : .

u . u ; .

, u MENU 9 . : CD CD .
12 cm CD, CD-R CD-RW . CD , 16 CD .

, . u DISPL . 2 .

CD !
8 cm CD CD ( CD) . CD CD . - CD . CD . Blaupunkt CD ! CD MP3/WMA CD . MP3/WMA .
CD , u 2 . . u CD .
CD . CD . u . CD CD. : CD , 1 . CD , u CD SOURCE 4 . .

, u / : .

(MIX)
u 5 MIX ; . MIX DISC MIX . . MIX u 5 MIX ; . MIX OFF MIX .

(SCAN)

CD ( ) . u MENU . SCAN DISC , . : . , .

u : . : , .

, u / : .

, u MENU 9 . .

CD : (Normal Mode): : (Info Mode): : : CD- (Clock Mode): : : CD- : CD . CD . CD CD . , u 8 DISPL .