03_BA_Casablanca_1_ENG.indd Inhalt70
Index Changing the volume presetting of trafc announcements (TRAFFIC)..117 Changing the volume presetting of the telephone (PHONE).118 Changing the volume presetting of the signal tone (BEEP).118 Changing the presetting of the power-on volume (ON VOL).118 Restoring the volume at switch-on (LAST VOL).118 Changing clock settings (CLOCK).119 Setting the time (TIME).120 Switching the time display on/ off with switched-off device (OFFCLOCK)..120 Switching the RDS synchronisation of the clock on/off (AUTOSYNC)..120 Switching the 24-hour time display on/off (24H MODE).120 Conguring audio inputs (AUX)..121 Activating/deactivating audio inputs (AUX1/2)..121 Renaming audio inputs (EDIT).121 Changing special settings (VARIOUS)..123 Changing the welcome text (ON MSG)..123 Switching the internal amplier on/off (AMP ON).124 Resetting the device to factory settings (NORMSET).124 Changing the scan time (SCANTIME).124 Displaying the serial number (SER NUM)..125 Error table..125 Technical data.126 Glossary..127 Index..130 Installation instructions.332
FRANAIS NEDERLANDS ITALIANO
Blaupunkt stands for technical know-how in mobile radio reception, for precise navigation systems and rst-class sound. The blue dot made its debut in 1923 as a seal of quality that was assigned after rigourous functional and it still applies today. At that time as well as today, the blue dot identies products of extraordinary quality. 71
03_BA_Casablanca_1_ENG.indd Inhalt71

31.05.2006 11:15:34 Uhr

For your safety

About these instructions

Please read these instructions and, in particular, the following chapter, "For your safety", before using the device! Please also observe the following instructions: CD Changer, if available Remote Control, if available
If you are installing device yourself You may only install the device yourself if you are experienced in installing car sound systems and are very familiar with the electrical system of the vehicle. Observe the following! Danger of injuries! Do not open or modify the device! The device contains a Class 1 laser that emits invisible laser radiation which can cause injuries to your eyes. The warranty is void if the device has been opened. Danger of accidents! Operate the device only if trafc situation permits it! Danger of hearing damage! Always listen at moderate volume so that you can always hear acoustic warning signals! This will also help to protect your hearing. The device briey switches to mute, e.g. while the CD changer changes the CD or if you are switching the audio source. Do not increase the volume during this mute phase

Device overview

Controls

9 : ; < =

for detaching the control panel 2 TUNER button Selecting the tuner as audio source Opening the "TUNER" menu 3 Rocker switch Tuner: Start the station seek tuning Settings menu: Change settings 4 On/Off button Press short: Switch on/mute Press long: Switch off 5 Volume control

button

6 NEXT button Tuner: Select memory bank (FM1, FM2, FM3, FMT) Settings menu: Go to the next menu page MP3/WMA: Switch between "PLAY", "BROWSER" and "PLAYLIST" 7 to < Softkeys to select the function shown on the display next to the respective button = to eject/insert a CD > Display (see page 80 and 81)
03_BA_Casablanca_1_ENG.indd Elemente74
Placing the device in operation ? MENU button to call up the settings menu @ ESC button Settings menu: Conrm menu item and change to the display of the audio source Scan/Travelstore: Cancel A OK button Press short: Conrm menu item and change to the next higher menu level Press long: Start scan/station seek tuning B SRC button Consecutively switching between the available audio sources C CD drive C
You can detach the control panel to protect against theft. CAUTION! Danger of theft! The device is worthless to a thief without the control panel. Never keep the control panel in the vehicle, not even in a hidden place; instead, carry it with you in its case when you leave the vehicle! CAUTION!

D MMC/SD card slot D

Damage to the control panel! The control panel can be damaged or malfunction if the following is not observed: Never drop the control panel. Do not expose the control panel to direct sunlight or another heat source. Transport it exclusively in the supplied case.
03_BA_Casablanca_1_ENG.indd Betrieb75

31.05.2006 11:15:36 Uhr

Detaching/attaching the control panel
Placing the device in operation

General functions

Do not touch the contacts on the rear side with your ngers. Clean the contacts of the control panel regularly using a soft cloth moistened with cleaning alcohol. To detach the control panel: button 1. Press the The control panel opens to the front on the left. The device switches off automatically. Detach the control panel. To attach the control panel: Place the control panel in the slot with the right side rst. Next, carefully push the left side to the back until the control panel engages.

To switch off the device: Press and hold the On/Off button 4 for approx. two seconds. In addition, the device is automatically switched off as soon as you switch of the vehicle ignition. If you switch on the ignition again, it also automatically switches on the device again.

Inserting a CD

CAUTION! Damage to CD drive from unsuitable CDs! Mini CDs (8 cm diameter) or shape CDs damage the drive! Insert only circular CDs with a 12-cm diameter into the CD drive. To insert an MP3, WMA or audio CD, the device must be switched on. button =. Press the The control panel opens. If a CD is in the drive, it is ejected. If you do not remove this CD, it is automatically pulled in again after approx. 10 seconds.
Switching the device on/off
To switch on the device: Press the On/Off button 4. The device plays the audio source you previously listened to. Note: If you switch on the device without rst switching on the vehicle ignition, the device automatically switches off after one hour to save the vehicle battery. 76
03_BA_Casablanca_1_ENG.indd AllgFkt76

31.05.2006 11:15:37 Uhr

Note: Blaupunkt cannot guarantee the correct functioning of all MMC/SD card available on the market and, for this reason, recommends the use of MMC/ SD cards manufactured by "SanDisk" or "Panasonic". The cards must be formatted using the FAT16 or FAT32 le system and contain MP3 or WMA les. Remove the control panel as described on page 9. Insert the MMC/SD card in the card slot D until it engages. The contacts of the card must point down and to the rear.
Note: Always switch off the device before connecting or disconnecting your USB medium! Connect the USB medium to the USB cable that is routed from the rear side of the device. The USB medium can now be selected as audio source. 77
03_BA_Casablanca_1_ENG.indd AllgFkt77

Inserting an MMC/SD card

To be able to connect a USB stick or a USB hard disk, the supplied USB cable must be connected to the rear side of the device before the installation as described in the installation instructions. This cable can be routed, for example, to the glove compartment or a suitable place of the center console.
Note: As long as the CD is in the drive, the device stores track and playing time of the CD played last, and after calling up the audio source, the playback starts at the position where it was interrupted.
Connecting the USB medium
Insert the CD with its printed side uppermost into the CD drive C until you feel some resistance. The CD is automatically drawn in and the control panel closes. This CD can now be selected as audio source.
Attach the control panel as described on page 9. This MMC/SD card can now be selected as audio source. To remove the MMC/SD card: Remove the control panel as described on page 9. Push on the MMC/SD card until it disengages. Pull the MMC/SD card out of the card slot D.
For the device to recognise the USB medium, it must be specied as mass storage device and formatted using the FAT16 or FAT32 le system and contain MP3 or WMA les. Blaupunkt cannot guarantee the proper functioning of all USB media available on the market. If extensive les are stored on your USB medium, the le search (see page 102) can be slow.

Note: To preset the volume of trafc announcements (TRAFFIC), a connected telephone (PHONE) and the signal tone (BEEP), see pages 117 and 118.

Muting the device

The device can be muted as follows: Briey press the On/Off button 4. The display shows "MUTE". To cancel the mute function: Briey press the On/Off button 4 again or turn the volume control 5.

Adjusting the volume

WARNING! Danger from excessive volume! Excessive volume can damage your hearing and you may fail to hear acoustic warning signals! Do not increase the volume while the device changes the CD in the CD changer or the audio source. Always set the device to a moderate volume. Turn the volume control 5. The current volume is shown in the central area B of the display and used for all audio sources.

Operation with telephone

If a hands-free system is installed in your vehicle or your cell phone is connected to the device via a Bluetooth adapter, the device responds as follows to incoming or outgoing telephone calls: The voice of the person calling you is played back via the loudspeakers of the vehicle. The display shows "PHONE CALL". The currently playing audio source is muted.
02_BA_Casablanca_1_GB.indd 78

11.09.2007 14:55:38 Uhr

Selecting an audio source
The device features the following audio sources: Tuner Integrated CD player (can play audio CDs as well as CDs with MP3 or WMA les) MMC/SD card with MP3 or WMA les In addition, the following external audio sources can be connected: Either an optional CD changer or AUX1 AUX2 (e.g. MiniDisc or external MP3 player) USB stick with MP3 or WMA les To be able to select an external audio source, it must be connected and contain audio data. Press the SRC button B repeatedly until the display briefly shows the desired audio source.
02_BA_Casablanca_1_GB.indd 79

11.09.2007 14:55:39 Uhr

During the telephone call, you
change the volume of the telephone call by means of the volume control 5. Trafc announcements (TA) are not automatically shown.

The tuner display

The audio CD display
RADIO KISS RADIO KISS RADIO SUN 93.40

FM1 TP XBS

94.60 96.20 97.70

MIX REPEAT TRAFFIC

CD 01:15 TP

TRACK 01

SHOW ALL SCROLL INFO

PTY 12:34

TUN>

TMC RDS 91.50 MHZ

XBS TMC RDS TEXT: EUROPE - FINAL CO

A Main line

Left: Arrow Middle: Station name or frequency Audio source
Left: Arrow Middle: Track number Audio source
B Central area C Memory location for radio stations which can be selected using the six softkeys 7 to <

03_BA_Casablanca_1_ENG.indd Tuner92
"1": Low seek tuning sensitiv-
Allowing/preventing automatic changing to other regional programmes (REGIONAL) Some stations divide their programmes into regional programmes with different contents at certain times. You can use the Regional function to prevent or allow the device from switching to alternative frequencies that are transmitting a different programme content. Change to the second page of the "TUNER" menu by pressing the NEXT button 6.
03_BA_Casablanca_1_ENG.indd Tuner93
ity. During a station seek tuning (see page 87), only local strong stations are found. "6": High seek tuning sensitivity. Poor, remote stations are also found.
Activating/deactivating improved reception (HIGH CUT) The High Cut function results in an improved reception in case of weak radio reception (FM only). Change to the second page of the "TUNER" menu by pressing the NEXT button 6. In the "TUNER" menu, repeatedly press the softkey 7 (next to "HIGH CUT"). "1": The High Cut function is switched on and has a low response sensitivity. If the reception is very poor, the interference level is automatically decreased. "2": The High Cut function is switched on and has a high response sensitivity. If the reception is poor, the interfer-
The "SENSITIVITY" menu appears. Press the softkey 7 (next to "FM") to set the seek tuning sensitivity for FM stations or press the softkey < (next to "AM") to set the seek tuning sensitivity for AM stations. Each seek tuning sensitivity can be adjusted in six increments.
Press the softkey 8 in the "TUNER" menu (next to "REGIONAL). "REGIONAL ON": The Regional function is switched on. The tuner does not even switch to other regional programmes if the reception quality becomes poor. "REGIONAL OFF": The Regional function is switched off. The tuner switches to other regional programmes if the reception of the current programme is too poor.
ence level is automatically decreased. "0": The High cut function is switched off. Restricting station seek tuning to certain programme contents (PROG TYP) Change to the second page of the "TUNER" menu by pressing the NEXT button 6. In the "TUNER" menu, press the softkey < (next to "PROG TYP"). Scroll through the pages of the programme types with the NEXT button 6. Press the softkey next to the desired programme type. Next, start a station seek tuning (see page 87). Toggle between mono and stereo operation (MONO) If you selected the "FM" waveband, you can toggle between mono and stereo operation. Change to the second page of the "TUNER" menu by pressing the NEXT button 6. Press the softkey 9 in the "TUNER" menu (next to "MONO"). "MONO ON": The mono operation is activated. Weak,

On the rocker switch 3, repeatedly press or to change the ashing character. On the rocker switch 3, press to change to the next character. Press the OK button A to nish the text input and to store the name entered. Note: To quit the text input without changing the name, press the ESC button @.
03_BA_Casablanca_1_ENG.indd CDC105

31.05.2006 11:15:50 Uhr

Changing the name of a CD in the magazine of the CD changer (CD NAME) You can assign a name to every CD located in the CD changer. The name can have up to seven characters. Select the CD to which you want to assign a name in the CD overview as described in the preceding section. Press the NEXT button 6 to show the CD changer display. Press the softkey < (next to "CD NAME"). Press the softkey 7 (next to "EDIT"). The text input appears. The rst character of the name is ashing.
Changing basic settings in the settings menu
To delete the name of the current CD: Press and hold the softkey < (next to "CLEAR CD") for longer than two seconds. The main line A briey displays "CLEARING".
To delete the names of all the CDs located in the magazine of the CD changer: Press and hold the softkey : (next to "CLR ALL") for longer than two seconds. The main line A briey displays "CLEARING".
The settings menu allows you to adjust basic device functions, such as sound, power-on volume or display brightness, to your specic needs. To open the settings menu: Press the MENU button ?. The settings menu appears.
AUDIO MENU TREBLE BALANCE FADER BASS DEQ SUBOUT
TIME OFFCLOCK CLOCK SETTING AUTOSYNC 24H MODE

DISPLAY

USER MENU BRIGHT SPECTRUM INVERT AUDIO DISPLAY VOLUME CLOCK AUX VARIOUS

AUX2 EDIT

AUXILIARY MENU AUX1
VOLUME SETTING TRAFFIC PHONE BEEP ON VOL LAST VOL

VOLUME

VARIOUS

ON MSG AMP ON

NORMSET SCANTIME SER NUM
03_BA_Casablanca_1_ENG.indd Men106
TREBLE -4 TREBLE BALANCE FADER

TREBLE

BASS DEQ SUBOUT
BASS +1 TREBLE BALANCE FADER
BALANCE +3 TREBLE BALANCE FADER

BALANCE

AUDIO MENU BASS DEQ SUBOUT TREBLE BALANCE FADER BASS DEQ SUBOUT USER EQ PRESET AUTO SND

DEQ MENU XBASS OFF

AUDIO AUDIO

DEQMAXEX

FADER +2 TREBLE BALANCE FADER
120Hz BASS DEQ SUBOUT TREBLE BALANCE FADER

GAIN +1

Changing treble or bass (TREBLE/BASS) Press the softkey 7 (next to "TREBLE") or the softkey < (next to "BASS"). The corresponding sound control is displayed. On the rocker switch 3, press or to increase treble or bass. On the rocker switch 3, press or to decrease treble or bass.
Changing the volume distribution (BALANCE/FADER) The balance controls the volume distribution between left and right, the fader between front and rear. Press the softkey 8 (next to "BALANCE") or softkey 9 (next to "FADER"). The volume distribution is displayed. On the rocker switch 3, press on the desired direction. The volume distribution changes. The display shows the new volume distribution.

03_BA_Casablanca_1_ENG.indd Men110
"Q2": Medium edge steepness and lter bandwidth narrow lter bandwidth The change is displayed in the frequency spectrum. The sound changes accordingly.
"Q3": High edge steepness,
ENGLISH NEDERLANDS ITALIANO FRANAIS
Select the centre frequency to be changed by pressing on or on the rocker switch 3. In the two frequency bands "LOW1" and "2", you can select one centre frequency each from 20 to 250 Hz. In the four frequency bands "HIGH1" to "4", you can select one centre frequency each from 320 to 20,000 Hz. On the rocker switch 3, press. The level display (dB) is highlighted. Select the level of the previously set centre frequency by pressing on or on the rocker switch 3. The level change is displayed in the frequency spectrum. The sound changes accordingly. On the rocker switch 3, press. The quality factor Q is highlighted. Select the desired quality factor Q by pressing on or on the rocker switch 3.
Press the OK button A. Your user-dened equalizer setting is saved. Which equalizer setting is the correct one?
Measure Sound impression or problem Centre frequency (Hz) Level (dB)
Unclean bass, 125400 droning, unpleasant pressure Very transparent, aggressive sound, no stereo effect 1000 2500

approx. 4

approx. 4 to 6
Mufed sound, 8000 low transparency, 12500 instruments do not excel Insufcient bass 50100

approx. +4 to +6

03_BA_Casablanca_1_ENG.indd Men111
"Q1": Low edge steepness,

wide lter bandwidth

Selecting a sound presetting (PRESET) This menu item allows you to select one of the following sound presets: VOCAL, DISCO, ROCK, JAZZ or CLASSIC. Press the softkey located next to the desired sound preset. The selected sound preset is highlighted and shown on the main line A. To turn the equalizer off, press the softkey : (next to "P-EQ OFF") instead. Setting the speed-dependent volume increase (AUTO SND) When you are driving faster, the device can automatically increase the volume to compensate for the driving noise. In order for this to work, the speedometer signal must be connected as described in the installation instructions. You can adjust this volume increase from 0 (no increase) to 5 (maximum increase). Repeatedly press the softkey 9 (next to "AUTO SND"). The current speed-dependent volume increase is shown on the main line A.

Note: If no increase is set, the main line A shows "AUTO SND OFF". On the rocker switch 3, press or to raise the volume increase. On the rocker switch 3, press or to lower the volume increase. Setting the bass increase (XBASS) XBASS is a bass increase at low volume. This bass increase can be set in increments from 0 (no increase) to 6 (maximum increase) for the following frequencies: 32 Hz, 40 Hz, 50 Hz, 63 Hz, or 80 Hz. Press the softkey ; (next to "XBASS"). The "XBASS" menu item is ashing. The frequency (Hz) and bass increase (GAIN) are shown on the main line A. On the rocker switch 3, press or to select the desired frequency. On the rocker switch 3, press or to set the desired bass increase. Conguring the preamplier output for the subwoofer (SUBOUT) If you want to use an additional subwoofer, it can be adjusted to the other loudspeakers.
03_BA_Casablanca_1_ENG.indd Men112

31.05.2006 11:15:53 Uhr

You can adjust the level of the Subout preamplier output in 13 increments from 6 dB (maximum decrease) to +6 dB (maximum increase) for one of the following cut-off frequencies: 80 Hz, 120 Hz, or 160 Hz. In the "AUDIO" menu, press the softkey : (next to "SUBOUT"). The "SUBOUT" menu item is ashing. The current cut-off frequency (HZ) and the current level (GAIN) are shown on the main line A. On the rocker switch 3, press or to select the desired cutoff frequency. On the rocker switch 3, press or to set the desired level of the preamplier output. Switching the equalizer off (OFF) In the "DEQ" menu, press the softkey : (next to "OFF").
03_BA_Casablanca_1_ENG.indd Men113

31.05.2006 11:15:54 Uhr

Changing display settings (DISPLAY)
In the "DISPLAY" menu, you can adjust the display brightness, colour and contrast, among other things. Press the MENU button ?. The settings menu appears. Press the softkey 8 (next to "DISPLAY"). The "DISPLAY" menu appears. The "DISPLAY" menu consists of two pages which can be toggled with the NEXT button 6.
DISPLAY COLOR OCEAN AMBER SUNSET NATURE COL-SCAN USER

ANGLE +1 COLOR ANGLE

DISPLAY MENU BRIGHT SPECTRUM INVERT COLOR ANGLE
SPECTRUM ON BRIGHT SPECTRUM INVERT COLOR ANGLE

ANALYSER

DISPLAY MENU SCREENSAVER ON SCREENS

COLOR ANGLE

DISPLAY MENU2 SCREENS
Changing the colour of the display (COLOR) You can change the colour of the display by selecting one of the four presettings ("OCEAN", "AMBER", "SUNSET" or "NATURE") or the user-dened colour ("USER").
To select one of the four presettings: Press the corresponding softkey (next to "OCEAN", "AMBER", "SUNSET", "NATURE" or "USER"). The colour of the display changes accordingly.

03_BA_Casablanca_1_ENG.indd Men114
Changing the user-dened colour (USER) Two options are available to change the user-dened colour. Option 1: Press the softkey : (next to "USER"). Set the desired colour using the softkeys 7 to <. "RED": Reduces the red portion. "GREEN": Reduces the green portion. "BLUE": Reduces the blue portion. "RED+": Increases the red portion. "GREEN+": Increases the green portion. "BLUE+": Increases the blue portion. The colour of the display changes accordingly. Option 2: Press the softkey ; (next to "COL -SCAN"). The display sequentially shows all colours that can be displayed. Press the softkey 7 (next to "SAVE") or the OK button A to select the colour currently displayed.
Press the softkey < (next to "BREAK") or the ESC button @ instead to exit the "COL -SCAN" menu item without changing the colour. Adjusting the display viewing angle (ANGLE) The angle at which the driver looks at the display is dependent upon, among other things, the installation position of the device, the seating position, and the physical size of the driver. You can adjust the display contrast to your viewing angle as follows. Press the softkey 8 (next to "ANGLE"). The "ANGLE" menu item is ashing. The current display contrast is shown on the main line A. On the rocker switch 3, press or to increase the display contrast. On the rocker switch 3, press or to decrease the display contrast. You can adjust the display contrast in 13 increments from 6 to +6. Changing the brightness of the display for day/night (BRIGHT) See page 85.
03_BA_Casablanca_1_ENG.indd Men115

31.05.2006 11:15:55 Uhr

Inverting the display (INVERT) Press the softkey : (next to "INVERT"). Bright portions of the display are displayed as dark, dark portions as bright. Switching the spectrum analyser on/off (SPECTRUM) Instead of displaying the audio source, the device can display a 5band spectrum analyser. For this purpose, the screen saver must be deactivated (see next section) and you must activate the display of the spectrum analyser as follows. Press the softkey ; (next to "SPECTRUM"). "SPECTRUM ON": The spectrum analyser can be displayed. "SPECTRUM OFF": The spectrum analyser cannot be displayed. The spectrum analyser automatically appears 16 seconds after the last button is pushed instead of the display of the audio source. You can also display the spectrum analyser manually: To do so, press the ESC button @ while the display of the audio source is shown. Press any button to switch the spectrum analyser off.

Switching the RDS synchronisation of the clock on/off (AUTOSYNC) The clock can automatically be synchronised with the RDS time signal, provided that a station is set that broadcasts this RDS time signal. Press the softkey < (next to "AUTOSYNC"). "AUTOSYNC ON": The synchronisation is switched on. "AUTOSYNC OFF": The synchronisation is switched off. Switching the 24-hour time display on/off (24H MODE) The time can be displayed using the 12-hour or 24-hour format. To switch between these two formats: Press the softkey ; (next to "24H MODE"). "24H MODE ON": The 24hour format is switched on. "24H MODE OFF": The 12hour format (AM/PM) is switched on.
03_BA_Casablanca_1_ENG.indd Men120

31.05.2006 11:15:57 Uhr

AUXILIARY 2 OFF AUX2

__ AUXILIARY 2 AUX2 EDIT

AUXILIARY MENU AUX1 EDIT AUX2 EDIT

__ AUXILIARY 1

Activating/deactivating audio inputs (AUX1/2) Audio inputs, to which you are connecting external audio sources, must be activated as follows. Press the softkey < (next to "AUX1") and/or the softkey 7 (next to "AUX2"). The status of the audio input is shown on the main line A:
audio source using the SRC button B. "AUXILIARY OFF": The corresponding audio input is deactivated. It cannot even be selected as audio source if an external audio source is connected. Renaming audio inputs (EDIT) If you select an audio input as audio source, "AUXILIARY 1" or "AUXILIARY 2" appears on the main line A. To change this name: 121
"AUXILIARY ON": The corre-
sponding audio input is activated and can be selected as
03_BA_Casablanca_1_ENG.indd Men121

AUX1 EDIT

AUXILIARY 1 OFF AUX2 EDIT AUX1
Up to two external audio source, such as MiniDisc player or external MP3 player, can be connected to the audio inputs AUX1 and AUX2. If you are connecting a CD changer, it occupies audio input AUX1 and you can also connect AUX2. The audio sources AUX1 and AUX2 cannot be operated using the Casablanca. Only the volume can be changed. Press the MENU button ?. The settings menu appears. Press the softkey ; (next to "AUX"). The "AUXILIARY" menu appears. The audio input "AUX1" is displayed only if no CD changer is connected.
Conguring audio inputs (AUX)
Note: The "EDIT" menu item appears only if you activated the corresponding audio input as described in the preceding section. Press the softkey 8 for AUX2 or the softkey ; for AUX (each next to "EDIT"). The text input for the selected audio source is shown on the main line A. The rst character of the name is ashing. On the rocker switch 3 repeatedly press or to change the ashing character. On the rocker switch 3, press to change to the next character. The name can have up to 16 characters. Press the OK button A to nish the text input and to store the name entered. Note: To quit the text input without changing the name, press the ESC button @.

The disadvantage is that the station may not be received without interferences. Root directory Main directory of a data carrier. The root directory contains all other directories. Subwoofer, Subout Separate low-bass loudspeaker. The device has a Subout preamplier output. You can connect either an active subwoofer or a separate power amplier with subwoofer. TA Trafc Announcement The device switches trafc announcements through, even if you are currently listening to other sources (e.g. CD, AUX) or the radio is muted. TMC Trafc Message Channel RDS data service for area-based trafc announcements. Digital trafc information data channel with continuously updated data about the trafc situation. TMC receivers allow for a selection of the data ow with respect to direction of travel, area or type of street. With a push of a button, you have access to the most current tailor-made information at all times.
03_BA_Casablanca_1_ENG.indd Glossar128
Tuner Receiving unit of the radio. USB Universal Serial Bus USB is an interface for connecting external removable storage devices to the device. XBASS XBASS means raising the bass at low volume. This renders the sound richer even at a low volume.
03_BA_Casablanca_1_ENG.indd Glossar129

31.05.2006 11:16:01 Uhr

T-STORE Travelstore Automatic searching and storing of the six strongest radio stations received of the region.
Your device has a TMC output, which you can use for connecting Blaupunkt navigation systems. Please contact your authorised Blaupunkt dealer for additional information.

Keyword index

Symbols 24H Mode 120 A ADJUST 109 Allowing alternative frequencies 92 Amplier 124 AMP ON 124 ANGLE 115 AREA 90 AUDIO 107 Audio inputs Activating 121 Conguring 121 Renaming 121 Audio source 79 Tuner 87 AUTO 109 AUTO SND 112 AUTOSYNC 120 AUX 121 B BALANCE 107 BAND 91 BAND button 74, 85 BASS 107 Bass increase 112 BEEP 118 Browser 102 Button for detaching the control panel 74 Buttons 74 Button to eject/insert a CD 74 C CD Changing the name of a CD in the CD changer magazine 105 Inserting 76
Removing 76 Selecting from the CD changer magazine 105 CD changer 104 Changing the name of a CD in the magazine 105 Display 81 Functions 104 CD changer display 81 CD display 80 CD overview 105 CD player 97 Display 80 Functions 98 CD text 99 Central area 80, 81 CLOCK 119 Clock 119 24-hour time display 120 Display with switched-off device 120 Setting 120 Synchronise with RDS 120 COLOR 114 Control panel 75 Correcting errors Correcting 125 Correcting malfunctions 125 Country code 90
D DEQ 108 DISPLAY 114 Display Brightness 85 Changing the colour 114 Inverting 116 Viewing angle 115 E EDIT 121 Equalizer 109, 113

Note: Keywords in capital letters refer to menu items. 130
03_BA_Casablanca_1_ENG.indd Index130
Calling up a user-dened setting 108 Creating a user-dened setting 109 Settings recommendations 111 ESC button 75, 85 MONO 94 Mono operation 94 MP3 Files on CD 97 MP3 display 81 MP3 player 101 Display 81 Functions 100 MUTE 78 Muting 78
G H HIGH CUT 93 I Improved reception 93 INFO 101 Info line 80, 81 INVERT 116 J K L LAST VOL 118 M Main line 80, 81 MANUAL 110 Memory bank 87 Memory card Card slot 75 Inserting 77 Removing 77 Menu Calling 85 Changing and saving a setting 86 Exiting 86 Operate 84 Operating example 85 Selecting a menu item 85 Settings menu 106 Tuner menu 91 MENU button 75, 84 MIX 81, 83 MMC card: see Memory card
Q R R-TEXT 92 Radiotext 92 Random track play 83 RDS 80, 92 Receiving a regional programme 93 Region Adjust 90 REGIONAL 93 Repeat 83, 84 Repeat mode 83 Repeat title 84 Reverse 82 Rocker switch 74, 82 RPT 81, 83
03_BA_Casablanca_1_ENG.indd Index131
P PHONE 118 Playlist 102 PRESET 112 PROG TYP 94 PTY 80, 94
O OFFCLOCK 120 OK button 75, 82, 85 On/Off button 74 ON MSG 123 ON VOL 118
N NEXT button 74, 84, 85 NORMSET 124
F Factory settings 124 FADER 107 FM1, FM2, FM3, and FMT 87 Forward 82
S Safety 72 SCAN 84 Scanning 84 SCANTIME 124 Scan time 124 SCREEN S 116 Screen saver 116 SCROLL 99, 101 SD card: see Memory card Seek tuning sensitivity 92 SENS 92 Serial number 125 SER NUM 125 Settings menu 106 SHOW ALL 101 Skip title 82 Softkey 74, 82 Sound 107 Presetting 112 SPECTRUM 116 Spectrum analyser 116 SRC button 75 Station Calling 89 Scanning 89 Searching 87 Storing 89 Stereo operation 94 SUBOUT 112 Subwoofer 112 Switch-off 76 Switch-on 76 T T-STORE 92 Telephone 78 TIME 120 Title information 101 TMC 80 TP 80 TRAFFIC 83, 117 Trafc announcements 83, 95 Priority 91, 95 Travelstore 92 TREBLE 107
Tuner Display 80 Functions 87 Menu 91 Tuner display 80
U USB medium Connecting 77 USER 115 V VARIOUS 123 VOLUME 117 Volume 78 At switch-on 118 Muting 78 Presetting 117 Speed-dependent increase 112 Volume control 74 Volume distribution 107 W Warranty 73 Waveband 91 Welcome text 123 WMA Files on CD 97 WMA player 100 Functions 100 X XBASS 112 XBS 80 Y Z
03_BA_Casablanca_1_ENG.indd Index132

31.05.2006 11:16:02 Uhr

Bitte den ausgefllten Gertepass sicher aufbewahren! Please keep the lled-in radio pass in a safe place! Prire de conserver soigneusement la carte dautoradio remplie ! Tenete per favore il libretto di apparecchio, debitamente riempito, in un posto sicuro! Bewaar de ingevulde apparaatpas op een veilige plaats!

07_EA_Casablanca_1.indd 341

31.05.2006 11:52:30 Uhr

Country: Germany Austria Belgium Denmark Finland France Great Britain Greece Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland Czech. Rep. Hungary Poland Turkey USA Brasil (Mercosur) Malaysia (Asia Pacic) (D) (A) (B) (DK) (FIN) (F) (GB) (GR) (IRL) (I) (L) (NL) (N) (P) (E) (S) (CH) (CZ) (H) (PL) (TR) (USA) (BR) (MAL)
Phone: 0180-5000225 01-0 02-360 09-01-01-01-700 02-1010 66-08-7501850 01-8471644 02-803 0800-118922 0212-71 800-7045446 +604-6382 474
Fax: 05121-01-391 02-44-09-01-01-01-706 02-1040 66-4078 08-7501810 01-8471650 02-809 022-8771260 0212-40 708-6817188 +55-2773 +604-6413 640
WWW: http://www.blaupunkt.com

Gertepass

Name: Typ: Serien-Nr:
Casablanca MP56... 580 310...
Blaupunkt GmbH, Robert-Bosch-Strae 200, D-31139 Hildesheim
09/07 - CM-AS/SCS1 (dt, gb, fr, it, nl)

8622404838

Rueck_Casa_1_838.indd 342

11.09.2007 15:43:00 Uhr