Radio / Cassette / Changer
Coburg RCM 127 Casablanca RCM 127 Cannes RCM 127 Woodstock DJ I Woodstock DJ A

Operating instructions

Coburg.RCM127 d

13.02.2001, 10:15 Uhr

Coburg Woodstock RCM 127 DJ I
Casablanca Cannes Woodstock

RCM 127 RCM 127 DJ A

Fernbedienung RC 06 (Option) Remote control RC 06 (optional) Tlcommande RC 06 (en option) Telecomando RC 06 (optional) Afstandsbediening RC 06 (Optie) Fjrrkontroll RC 06 (Tillval) Mando a distancia RC 06 (opcional) Telecomando RC 06 (opo)
Coburg.RCM127 d 2 13.02.2001, 10:15 Uhr
Quick reference.. 28 Important notes.. 33
Precautions.. 33 Traffic safety... 33 Installation.. 33 Sound source mute.. 33 Accessories.. 33
KeyCard theft protection system 34
Putting the unit into operation. 34 Removing the KeyCard. 34 Training a second KeyCard/ Replacing a KeyCard.. 34 Displaying the radio pass data. 34 Short Additional Memory (S.A.M.). 35 Turn On Message (T.O.M.). 35 Optical indication of anti-theft protection... 35 Care of your KeyCard.. 35

DSC programming.. 47

Overview of DSC factory settings. 49
Radio operation with RDS. 36
AF - Alternative frequency.. 36 REG - regional programme. 36 Selecting a waveband (only Casablanca RCM 127, Cannes RCM 127, Woodstock DJ A). 36 Station tuning.. 37 Automatic tuning /.. 37 Manual tuning with << >>. 37
Coburg.RCM127 gb 27 13.02.2001, 10:19 Uhr

PORTUGUS

Traffic announcement priority on/off. 42 Beep tone.. 42 Switching off the beep tone.. 42 Automatic seek tuning start. 42
Specifications.. 49 Blaupunkt telephone hotline.. 49

ESPAOL

Receiving traffic programme stations with RDS-EON. 42

Appendix.. 49

SVENSKA
Switching the audio source. 35
Scrolling through the broadcasting networks.. 37 Changing the memory bank.. 37 Storing stations.. 37 Automatically storing the strongest stations with Travelstore.. 38 Recalling stored stations.. 38 Scanning stored stations with Preset Scan.. 38 Scanning stations with Radio-Scan. 38 Selecting the seek tuning sensitivity. 39 Switching from stereo to mono. 39 Loudness... 39 PTY Programme-Type.. 39 Switching PTY on/off.. 39 Programme type.. 39 Checking the programme type of the station.. 40 Displaying the selected programme type.. 40 Selecting a programme type. 40 Storing programme types. 41 Scanning stations with PTY-SCAN. 41 PTY priority.. 41
Adjusting the volume for traffic announcements and the beep tone. 43

CD changer operation. 45

Switching to the CD changer mode. 45 Selecting CDs and titles.. 45 MIX playback.. 45 Selecting the display mode. 46 SCAN.. 46

NEDERLANDS

ITALIANO
Inserting a tape.. 43 Removing a tape.. 43 Fast Forward/Rewind.. 43 Selecting titles with CPS.. 43 Switching the tape side (autoreverse). 44 Tape equalisation.. 44 Scanning cassette titles with SCAN.. 44 Listening to the radio during fast tape winding with RM.. 44 Care notes.. 44

FRANAIS

ENGLISH

Tape operation.. 43

DEUTSCH

Contents

Quick reference
1 Switching on/off with the ON button: Press ON. When switching the set on with the ON button, the KeyCard has to be inserted. The unit will play with the pre-adjusted volume. Switching on/off via the ignition: When connected correspondingly, the set can also be turned on and off with the vehicle ignition. After the ignition has been switched off, a double beep tone will remind you that you should remove the KeyCard before leaving your vehicle. Switching on with the ignition being switched off: To keep on operating the set when the ignition is switched off (KeyCard is inserted), proceed as follows: Press ON. The unit will be turned on. To avoid that the battery goes flat, the system will be turned off automatically after one hour of playback. 2 VOL+ / VOLTo alter the volume. Each time the set is switched on, it will play with the pre-adjusted volume (VOL FIX). You may also change the VOL FIX setting (see chapter DSC programming). 3 For instantly muting the volume. button the volume By pressing the can be muted immediately. MUTE will appear in the display. The function is cancelled by pressing button or VOL+. (mute) When pressing VOL-, the volume will be adopted. To programme the mute volume level, proceed as follows: Adjust the desired volume. for 1 second until you Press hear a beep. Now this volume level is stored as your mute volume.

8 AF Alternative frequency during RDS operation: When AF lights up in the display, the system will automatically seek a frequency offering better reception of the same RDS programme. AF on/off: Press AF briefly. Regional function on/off: Press the AF button for approximately 1 sec. until you hear a beep. REGON or REG-OFF will appear in the display (see chapter REG - regional programme). 9 TA (priority for traffic announcements) When TA lights up in the display, the system will play traffic stations only. Priority on/off: Press TA. : 1, 2, 3, 4, 5, 6 - preset buttons You can store six stations for each of the memory banks I, II and T. To store a station: Press a preset button during radio operation and hold down until the set resumes play after the muting and you hear a beep. To recall a station: Select the desired memory bank and press the relevant preset button briefly.
Casablanca RCM 127, Cannes RCM 127, Woodstock DJ A: Additional selection of medium- and long-wave stations, provided that AM ON has been adjusted in the DSC menu.
Coburg.RCM127 gb 30 13.02.2001, 10:19 Uhr
Extra function of preset buttons To store and recall a PTY programme type. When PTY is active (PTY lights up in the display), you can store and recall one programme type on/from each preset button on FM. ; SRC (Source) You can switch between the radio, tape and CD changer operating modes, provided that a cassette/CD is inserted. < lo To switch the seek tuning sensitivity level: Press button briefly. If lo is displayed, the radio will only pick up strong, local stations (normal sensitivity). If lo does not light up, the radio will also pick up weaker, distant stations (high sensitivity). =
Extra function of lo button: To switch between mono and stereo reception: Press button for approximately 1 sec. (beep). The selected condition will be briefly displayed. / To switch the tape side: Press briefly. To eject the tape: Press for approximately 1 sec. Extra function / Frequency display during radio operation: Press button briefly. The frequency will be briefly displayed. > Cassette loading slot Insert the tape with side A or 1 facing up, the open side showing to the right.
? SC Radio operation Scan Press SC briefly. The scanned frequency or the station name will start flashing in the display. During the actual scanning process FM-SCAN or AM-SCAN will be displayed. The unit will scan all FM stations which can be received. Preset Scan Press SC for approximately 1 sec. until you hear a beep. SCAN and the name or frequency of the scanned station will alternately appear in the display. The unit will scan all stations stored on the preset buttons. To stop Scan / Preset Scan: Press SC once again.

Coburg.RCM127 gb 31 13.02.2001, 10:19 Uhr
Tape operation Cassetten-Scan Press SC. CC-SCAN will appear in the display. All cassette titles will be scanned briefly. To stop cassette scan: Press SC once again. Changer operation CD-Scan Press SC briefly. CDC-SCAN will appear in the display. All CD titles will be scanned briefly. To stop CD-Scan: Press SC once again. @ PTY (Programme Type) In the PTY mode, the preset buttons become programme type buttons. With every preset you can select one programme type, such as for example NEWS, SPORT, POP MUSIC, EDUCATE, etc.
A DSC (Direct Software Control) Use the DSC function to customise certain programmable, basic settings to suit your personal needs and preferences. See chapter DSC programming for more information. B AUD To adjust the treble, bass, balance and fader. If the display shows TRE or BAS, you can adjust the reproduction of the treble and bass frequencies with the rocker switch. If BAL or FAD is displayed, you can set the balance (left/ right) and fader (front/rear). Press AUD as many times as required and make the setting using the rocker switch.
The last setting will be stored automatically. To switch off AUD: Press button once again. If the setting remains unchanged within 8 seconds, the display will switch back to the previous condition. Extra function AUD Loudness - When listening at a low level, the Loudness function creates a more natural sound by boosting the low frequency range. Loudness on/off: Press AUD for approximately 1 sec. LD lights up in the display if the Loudness function is switched on. Please refer to chapter DSC programming for more information on how to program the Loudness boost.
Treble + / Fader front Treble / Fader rear Bass / Balance left Bass + / Balance right
Coburg.RCM127 gb 32 13.02.2001, 10:19 Uhr

Precautions

Before starting to use your new car radio, please read the following information carefully.

Installation

If you would like to install your new car stereo yourself or add other audio components to existing ones, then please read carefully the enclosed instructions on installation and connection. In order to ensure that the set operates properly it is necessary that the positive power supply line is connected to the ignition and the permanent +12 V lead. Do not ground the loudspeaker outputs!

Accessories

Use accessories and spare parts approved by Blaupunkt only. You can use the following Blaupunkt products with this car radio: Amplifier All Blaupunkt amplifiers, the preamp-out cable is required. Changer CDC A 05/F 05 (adapter cable is required), CDC A 06

Traffic safety

Traffic safety always has the highest priority. As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation at all times. Never use your car radio in a way that could distract you. Please keep in mind that you travel a distance of 14 m per second at a speed of only 50 km/h. Should the traffic situation become particularly demanding, we advise you not to use the radio. Always make sure that you are still able to hear any warning signals coming from outside of the vehicle, such as police or fire engine sirens, so that you can react accordingly. Therefore, you should always select a moderate volume for playing your car radio while you are driving.

Telephone mute

If there is a mobile telephone installed in your vehicle, the radio, tape player or CD player can be muted automatically when the phone is being used. PHONE will then appear in the display. When TA is active, traffic messages will always have priority. The announcement will be aborted by pressing the TA button.
(Woodstock DJ I, Woodstock DJ A): CDC A 06 included in the delivery.
Remote control With the infrared remote control RC 06 you can control all of the important functions of your car radio system from the steering wheel.
Coburg.RCM127 gb 33 13.02.2001, 10:19 Uhr

Important notes

KeyCard theft protection system
This car radio is supplied with one KeyCard as standard, though it can also be operated with a second card. If you have lost your KeyCard or if it was damaged, you can buy a new one from your specialised dealer. When using a second KeyCard, the settings stored on the first card will be adopted. However, you can individually store the following functions: Bass, treble, balance and fader settings, Loudness, TA (traffic announcement volume), beep volume. In addition, the settings activated before switching the radio off, such as the station tuned in, TA priority, AF, AM ON/OFF and RM ON/OFF will also remained stored. This ensures that you will find your basic settings re-adjusted automatically as soon as you have inserted your KeyCard. The system will switch off after approximately 10 seconds. When inserting another card type (e.g. phone or credit card), the display will show WRONG KC for approximately 2 seconds. The set will switch off automatically. Remove the wrong card and introduce the correct KeyCard. Press ON to turn on the set. Push in the KeyCard. The card is released and put in the proper position for being removed.

Removing the KeyCard

Never pull out the KeyCard directly! First, slightly push in the KeyCard. This releases the card and puts it in the proper position for being removed. Now you can pull it out.
Remove the first KeyCard and insert the new one. After the display indication READY or LEARN KC, press DSC. Now you can also use the new KeyCard for operating your unit. A maximum of two cards can be used for the set. When trying to train a third one, the access authorisation for the KeyCard not used for the training process will be deleted automatically.
Training a second KeyCard/ Replacing a KeyCard
While operating the unit with the first KeyCard, you can train a second one to be also used with the set: Insert the first KeyCard and turn on the set. Press the DSC button and select LEARN KC with /.
Displaying the radio pass data
Using the KeyCard supplied with your set you can have the radio pass data such as the model name, product number (7 6.) and serial number indicated on the display panel. Please refer to chapter DSC programming - READ KC.
Putting the unit into operation
Turn on the set. With the KeyCard tongue sticking out, introduce the KeyCard into the slot with the contact area showing up. The car radio is now ready for operation. If a wrong KeyCard is inserted, then CARD ERR followed by WAIT will appear in the display. In this case please do not make any further adjustments. 34

Coburg.RCM127 gb 34

Press << or >>. The display will switch to CHANGE.

13.02.2001, 10:19 Uhr

Short Additional Memory (S.A.M.)
Using the second KeyCard to be purchased at any specialised dealership, you can program a short text by selecting the DSC menu item READ KC. This text will be moved through the display and might be the telephone number of a car repair service or the emergency call number of your auto club. Any specialised dealer with the proper equipment can program the desired text with up to a maximum of 162 characters onto the KeyCard.
Optical indication of anti-theft protection
Flashing KeyCard tongue When the vehicle is stationary and the KeyCard removed, the KeyCard tongue can be switched to flash for extra anti-theft security. For this it is necessary that the positive power supply line and the permanent +12 V lead are connected such as described in the installation instructions. Be sure that LED ON is adjusted in the DSC mode. If required, please refer to chapter DSC programming - LED. Switching off the flashlight The flashlight can be switched off by pushing in the KeyCard and lock. If you would like to deactivate the flashing tongue with general effect, adjust the relevant item in the DSC menu to LED OFF.
Using the SRC button you can switch between the following audio sources: radio, tape, changer (optional for Coburg RCM 127, Casablanca RCM 127 and Cannes RCM 127). Tape/changer operation is only available if a cassette/disc is inserted. To switch to another source, press SRC briefly.

Coburg.RCM127 gb 35 13.02.2001, 10:19 Uhr
In order to ensure that the KeyCard always functions correctly, it is important for the contacts to be free from any foreign particles. Avoid direct skin contact. If necessary, clean the KeyCard contacts using a cotton swab dipped in alcohol.
Using the second KeyCard to be purchased at any specialised dealership, you can program the unit to display a selected Turn On Message after the set is switched on. Any specialised dealer with the proper equipment can program the desired text with up to a maximum of 48 characters onto the KeyCard. Each time you switch on your car radio using the second KeyCard, this text will appear in the display.

Care of your KeyCard

Turn On Message (T.O.M.)
Switching the audio source
Radio operation with RDS (Radio Data System)
The Radio Data System offers you more convenience when listening to FM radio stations. More and more radio stations have begun to broadcast RDS information alongside their programmes. As soon as a programme has been identified, the station name including a regional identifier, if applicable, will appear in the display, for example, NDR1 NDS (regional programme in Lower Saxony, Germany). When RDS is activated, the preset buttons become programme buttons. You now know exactly which programme you have tuned into, making it easy to find the desired station quickly. But RDS offers you further advantages: switching on the radio or recalling one of the stored frequencies, the unit is automatically searching for an alternative frequency. SEARCH will disappear from the display when the alternative frequency has been found or after the frequency band has been run through completely. If the reception quality of the selected programme becomes too bad: Tune into another station. If you leave the service area of the regional programme tuned into, or if you would like to take advantage of the full RDS service, switch to REG OFF. Press the AF button for approximately 1 sec. until REG OFF appears. If the REG function is active, REG ON will be briefly displayed each time the radio is switched on.

Selecting a waveband REG - regional programme
Certain radio programmes are split up at times into regional programmes offering local information. The 1st programme broadcast by NDR, for example, offers programmes with different contents in the northern states of Germany Schleswig-Holstein, Hamburg and Lower Saxony at certain times of the day. If you are listening to one regional programme and move to an area where another linked regional programme becomes stronger, the unit will switch to that programme. If you wish to continue listening to the first programme, press the AF button for approximately 1 sec. REG ON appears in the display.
(only Casablanca RCM 127, Cannes RCM 127, Woodstock DJ A)
You can select between the following wavebands: FM 87.5 - 108 MHz MW 531 - 1602 kHz LW 153 - 279 kHz Press the BND button until the desired waveband shows on the display panel. Note: In the DSC menu you can deactivate the station selection on either MW or LW or for both wavebands at the same time. This has the advantage that only the required bands will allow to be activated, so that you must press the BND button less often. For more information, please refer to chapter DSC programming - AM ON/OFF.
AF - Alternative frequency
The AF (Alternative Frequency) function makes sure that the strongest frequency of the currently selected programme is always tuned in automatically. This function is activated when AF appears in the display. In order to switch this function on or off, press the AF button briefly. While searching for the strongest reception signal, the radio may switch to mute briefly. If SEARCH appears in the display when 36

Coburg.RCM127 gb 36

Station tuning
Automatic tuning / Press / ; the car radio will automatically search for the next station. When keeping the upper or lower part / of the rocker switch depressed, seek tuning will speed up in upwards or downwards direction.
Manual tuning: Press << >>; the frequency will change in short intervals in downwards or upwards direction. When holding the right or left part of the rocker switch depressed, the frequency scan is speeded up.

Storing stations

Notice: Should you tune in a station which has already been stored before, then the corresponding preset position and memory bank will briefly flash in the display.
Recalling stored stations
Scanning stations with RadioScan You can recall any stored station at the touch
of a button. Select the memory bank with FMT or BND. Press the corresponding preset button briefly to recall the station. You can also scan all stations which can currently be received. To start the Scan function: Press SC briefly. The scanned frequency or the station name will start flashing in the display. During the actual scanning process FM-SCAN or AM-SCAN will be displayed. To select a scanned station and switch off Radio-Scan: Press SC briefly. If no station is selected, the scan function will be automatically switched off after the frequency band has been run through completely. The unit will tune in the station listened to before starting the scan.
Automatically storing the strongest stations with Travelstore
You can automatically store the six most powerful FM stations of your current reception area sorted according to their signal strength. This function is particularly convenient on longer trips. Press the FMT or BND button for 1 sec. T-STORE will appear in the display. The six strongest FM stations will be automatically stored on the memory bank T (Travelstore). When this process has been completed, the radio will play the first station stored on preset 1. If desired, stations can also be stored manually on the Travelstore bank (see Storing stations).
Scanning stored stations with Preset Scan
You can have all of the stored stations briefly scanned on all wavebands. To start Preset Scan: Press SC for approximately 1 sec. All of the stored stations to be received will be scanned one after the other. To select a scanned station and switch off Preset Scan: Press SC briefly. Note: If TA shows on the display panel, the system will scan the stored traffic stations only.
Coburg.RCM127 gb 38 13.02.2001, 10:19 Uhr
Selecting the seek tuning sensitivity
You can alter the automatic seek tuning sensitivity. If lo is displayed, the radio will only pick up strong, local stations. If lo does not light up, the radio will also pick up weaker, distant stations. To switch the seek tuning sensitivity: Press lo briefly. The sensitivity level can be altered separately in both modes. Please refer to chapter DSC programming - S-LO, S-DX).

Loudness

Adjusts the low bass frequencies for a more natural sound. Switching Loudness on/off: Press the AUD button for approximately 1 sec. When the Loudness function is active, LD will light up in the display. See chapter DSC programming for more information.

Programme type

Use << >> to have the last selected programme type displayed and to choose a new one. You can select any one of the stored types with the preset buttons 1-6. Condition: PTY must be active. Using DSC you can choose between German and English (see DSC programming PTY LANG). All of the programme types listed below are available. The letters printed in bold are identical to the actual short-time indication in the display. NEWS CURRENT AFFAIRS INFORMATION SPORT EDUCATE DRAMA CULTURE SCIENCE VARIED POP MUSIC ROCK MUSIC M.O.R. M (middle of the road music) LIGHT M (light classical) CLASSICS (serious classical)

PTY Programme-Type

PTY is an RDS service offered by more and more radio broadcasters. This feature allows you to select FM stations according to their programme type. After you have chosen the PTY of your preference, the corresponding stations can be selected either by seek tuning or using the scan function. Switching PTY on/off Press PTY. When the function is active, the programme type selected last will briefly appear in the display. PTY will be permanently indicated in the lower right corner of the display panel.
Coburg.RCM127 gb 39 13.02.2001, 10:19 Uhr
Every time the radio is switched on, stereo playback is activated automatically. The unit will gradually switch to mono if reception is poor. You can also switch between mono and stereo reception manually: Press the lo button for approximately 1 sec. The selected condition will briefly appear in the display.
Switching from stereo to mono
OTHER M (other music) WEATHER FINANCE CHILDRENS PROGRAMMES SOCIAL AFFAIRS RELIGION PHONE IN TRAVEL HOBBIES JAZZ MUSIC COUNTRY MUSIC NATIONAL MUSIC OLDIES MUSIC FOLK MUSIC DOCUMENTARY ALARM TEST Checking the programme type of the station Press PTY for approximately 1 sec. After the beep tone the display will show the programme type offered by the tuned in station. If NONE appears in the display, the current station has no PTY code.
Displaying the selected programme type Press << or >>. The programme type selected last will be displayed briefly. Selecting a programme type a) Using the preset buttons When PTY is switched on, you can use the preset buttons 1-6 to select the programme types stored at the factory. Press one of the presets 1-6. The selected programme type will be displayed for 2 seconds. If you wish to listen to a station with this PTY, press / to start seek tuning. If the system is unable to find a station offering the selected programme type, the display will show NO PTY and a beep tone will be released. The station received before starting seek tuning will be tuned in. You can assign different programme types to each preset position. Please refer to chapter Storing programme types.

b) Using the << >> buttons of the rocker switch When PTY is switched on, you can select a programme type using buttons << >>. Press << or >>; the programme type selected last will be displayed for 3 seconds. During this period press >> (forwards) or << (backwards) to select the desired type. Press << or >> as many times as required.
If you wish to listen to a station offering the selected PTY, press / to start seek tuning. If the system is unable to find a station offering the selected programme type, the display will show NO PTY and a beep tone will be released. The station received before starting seek tuning will be tuned in.
Coburg.RCM127 gb 40 13.02.2001, 10:19 Uhr
Storing programme types At the factory, one programme type was assigned to each of the preset buttons 1-6. If desired, you can also store other available programme types. To do so, make sure that PTY lights up in the display. If necessary, press the PTY button to switch on the function. Select a programme type using buttons << >> and
PTY priority Situation: PTY is switched on and lights up in the display. No station offering the selected programme type can be currently received (neither with seek tuning nor with scan). The set will switch back to the previous station. As soon as a programme with such PTY can be received within the broadcasting network, the unit will switch over to the corresponding station for the duration of the programme. Example: German broadcasting network NDR: Station tuned in: NDR3. PTY lights up in the display. Programme type POP selected. Seek tuning is started. No station with PTY-POP can be found. The display shows NO PTY and automatically switches back to NDR3. NDR2 airs a PTY-POP programme. The system will switch to the linked NDR2 station for the duration of the POP programme. 41 During tape operation, the set will also automatically switch to the programme offering the selected PTY within the broadcasting network. After the PTY programme the system will remain in the radio mode. Notice: As mentioned earlier, these functions are currently only supported by a limited number of RDS stations.

Scanning stations with PTY-SCAN Condition: PTY must appear in the display. Press the SC button. All of the received stations offering the selected programme type will be scanned. To switch off PTY-SCAN: Press SC once again.

Coburg.RCM127 gb

hold down the desired preset button (1-6) until you hear a beep. Now the selected programme type can be recalled by pressing this preset. For this, the PTY function must be active.
Receiving traffic programme stations with RDS-EON
The abbreviation EON stands for Enhanced Other Networks, meaning the exchange of information within a radio network. Many FM broadcasters offer traffic messages for their service area at regular intervals. All traffic programme stations transmit a special carrier signal alongside their programmes, which is decoded by your car radio. If this signal is identified, TP will appear in the display (Traffic Programme). In addition to these, there are also stations which do not actually transmit traffic programmes themselves, but by using RDSEON they offer the possibility to receive the traffic messages broadcast by another traffic programme station in the same radio network. If you wish to have the priority for traffic announcements activated while listening to one of these stations (e.g. NDR3), TA must appear on the display panel. If a traffic announcement is broadcast, the radio will automatically switch to the linked traffic programme station (in this case, NDR2) for the duration of the message and return to the original programme (NDR3) afterwards.
Traffic announcement priority on/off
If the priority for traffic announcement programmes is activated, TA will light up in the display. To switch the priority on or off: Press the TA button. When pressing TA while a message is being broadcast, this message will be interrupted. The unit will then switch back to the previous condition. The priority for all other traffic messages remains active. Please note that several buttons have no function while a traffic announcement is broadcast.
Switching off the beep tone a) Tune into another station offering traffic information: Press the rocker switch or press a preset button which has a traffic programme station allocated to it. Alternatively: b) Switch off the priority for traffic announcements: Press TA. TA will disappear from the display.

Automatic seek tuning start
(tape and CD changer operation) When leaving the reception area of the tuned in traffic programme station while listening to a tape or CD, the system will automatically start searching for a new TA programme. If no such station is found within approximately 30 seconds, you will hear a warning beep every 30 seconds. To switch off the beep tone proceed as described above.

Beep tone

If you leave the reception area of the traffic programme station currently tuned into, you will hear a beep tone approximately every 30 seconds. This tone will also be released when pressing a preset button which has no traffic programme allocated to it.
Coburg.RCM127 gb 42 13.02.2001, 10:19 Uhr
Adjusting the volume for traffic announcements and the beep tone
This volume was preset at the factory, though you can alter the value using the DSC function (see DSC programming, TA VOL). If the volume level is altered while a message is being played, this will only affect the current announcement.
The car stereo has to be switched on. The unit will automatically switch to tape operation when inserting a cassette.

Fast Forward/Rewind

Inserting a tape

Turn on the set.

Fast forward Fast rewind / Title selection (S-CPS) Up Down.
Stop function by pressing
Insert the tape with side A or 1 facing up, the open side showing to the right.
Selecting titles with CPS
(Cassette Programme Search) Use this function to skip ( ) and repeat ( ) recorded titles.

Removing a tape

Press for 1 sec. The cassette will eject.
Coburg.RCM127 gb 43 13.02.2001, 10:19 Uhr
To start CPS: Press /. In order for CPS to function properly, there has to be an unrecorded tape portion of at least 3 seconds between the individual titles.
Insert a tape. The cassette will be automatically transported to the playback position. Side A or 1 starts to play. During tape operation, TR 1 or TR 2 (track) will be indicated on the display panel.
Switching the tape side (autoreverse)
To change the tape direction during cassette playback: briefly. Press At the end of a tape side the mechanism changes directions automatically to play the other side (autoreverse). The display shows TR 1 for track (side) 1 or TR 2 for track 2. Notice: If there is too much tension on the tape during playback, the set may switch over by itself before having reached the end of the tape side. In this case check the condition of the cassette tape. Sometimes it helps to rewind it completely.
Scanning cassette titles with SCAN
You can have the cassette titles played briefly by using the scan function. If you like a title, stop the scan to continue listening to that track. To start/stop the scan function: Press the SC button briefly. Scan condition: There has to be an unrecorded tape portion of at least 3 seconds between the individual titles.

87.MHz

(Casablanca RCM 127, Cannes RCM 127, Woodstock DJ A) MW kHz LW kHz
FM sensitivity: 0.9 V at 26 dB signalto-noise ratio
Subject to modifications! 49
Coburg.RCM127 gb 49 13.02.2001, 10:19 Uhr
CD changer Frequency response: 5 - Hz
(Casablanca RCM 127, Cannes RCM 127, Woodstock DJ A): AM ON
Tape player Frequency response: 30 - Hz
FM frequency response: 30 - Hz
Using the area code to be entered you will be automatically given the address and phone number of the next Blaupunkt service centre. You can also request this information by fax.
Then call the following chargeable phone number: / 56 66.
If you would like to know the address of the next Blaupunkt service centre of your area without having our service list at hand: - Find out your area code.

Tuner Wavebands: FM :

Address of the next service centre in your vicinity (only for Germany)
Blaupunkt telephone hotline

Appendix