C-RF6ir
6-Disc FM Modulator CD Changer with Infrared Sensor - For Use With Any FM Vehicle Radio Changeur de CD a capteur infrarouge /modulateur FM a 6 disques.Cambiador de Discos Compactos Para 6 Discos con Sensor lnfrarojo y Modulador de FM Para Uso con Cualquier Radio FM de Vehiculo Cambiador CD para 6 discos corn Modulador FM corn Sensor lnfravermelho para uso coin qualquer Radio FM de Automovel

@BLAUPUNKT

Bosch Group

Owners Record

The model and warranty numbers are located on the rear of the unit. Record the warranty in the space provided below. Refer to these numbers whenever you call upon your Blaupunkt dealer regarding this product. Model No. CDC-RF6ir Warranty Number

FCC Warning

The equipment has been tested and found to comply with the limits for a Class B device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance with instructions, may cause harmful interference with radio communications. However, there is no guarantee that radio interference will not occur in particular installation.
The shielded interface cable recommended in this manual must be used with this equipment in order to comply with limits for a digital device pursuant to Sub-part B of Part 15 of the FCC rules. Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. You are cautioned that any changes or modifications not expressly approved in this manual could void your warranty and authority to operate this equipment. If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer.
CAUTION The use of optical instruments with this product will increase eye hazard. Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. Safety Certification This Compact Disc Player is made and tested to meet exacting safety standards, It meets FCC requirements and complies with safety performance standards of the U.S. Department of Health and Human Services.
Staple Your Sales Receipt Here

Table of Contents

Before installing and operating this unit, please read this manual thoroughly and retain it for future reference. Antes de instalar y operar esta unidad, por favor lea este manual detenidamente y guardelo para referencia en el futuro.

English

Ownerss Record.. 2 FCC Warning... 2 Features... 4 Precautions... 4 Before lnstallating and Testing The System. Electrical Connections..6 Installation.. 7 Specifications...12 Magazine & Compact Discs..13 Location of Controls...14 Operating Instructions..15 Optional Wireless Fiemoto Control.16 Switching to A Second CD Changer. 16 Switching to Radio or Cassette.. 16 Troubleshooting Guide..17 Error Codes... 18 Avant dinstaller et de faire fonctionner cet appareil, veuillez lire attentivement ce manuel et le conserver afin de pouvoir le consulter a Iavenir si nkcessaire.

lndice

Apuntes del Propietario.35 Advertencia de la FCC..35 Caracteristicas..36 Precauciones... 36 Antes de lnstalar y Probar el Sistema.36 Conexiones Electricas..38 Instalacion... 39 Especificaciones..44 Compartimiento de Discos y Discos Compactos.Ubicacion de 10s Controles. 46 lnstrucciones de Operation..47 Control Remoto Inalambrico Optional.48 Cambio a un Segundo Cambiador.48 Cambio a Ejecucion de Radio o de Cinta.48 Guia de Detection de Problemas..49 Codigo de Errores.. 50 Antes de instalar e operar esta unidade, por favor leia este manual minuciosamente e guarde-o para futura referencia.

Sommaire

Archive du proprietaire..19 Avertissement de la FCC..19 Caracteristiques.. 20 Precautions a prendre..20 Avant de monter et de tester le systeme.20 Raccordements electriques. 22 Installation... 23 Specifications...28 Compartiment CD & disques compacts..29 Emplacement des commandes..30 Mode demploi-Fonctionnement g&&al..Commande a distance sans fil optionnelle..Comment passer A un second changeur de disques compacts... 32 Comment passer au mode Radio & Cassette.Guide de depannage..33 Codes derreurs..34

indice

Registro do Proprietario.. 51 Avis0 da FCC..51 Caracteristicas... 52 PrecaucBes... 52 Antes de lnstalar e Testar o sistema.52 Conexoes Eletricas.. 54 Instalacao... 55 Especificacdes..60 Porta-discos e Discos Laser..61 Localizacao dos Controles.62 Instrucoes de Funcionamento..63 Controle Remoto sem Fio Optional..64 Mudando para urn Segundo Cambiador CD.. Mudando para o Radio e Toca-fitas..64 Guia para Soluc%o de Problemas..65 Mensagens de Erro..66

Features

Congratulations on your purchase of your Blaupunkt CDC-RF6ir FM Modulator CD Changer. This unit is designed to convert CD sound into FM signals (89.1 MHz or 88.7 MHz) and play them through any FM car stereo. This unit features: For Use With Any Electronically-Tuned FM Vehicle Radio Includes: l Changer l Wired Remote Control l FM Modulator l Disc Magazine l Cables l Mounting Hardware Features Include: l Disc and Track Select l Audible Cue/Review l Pause/Play l Switchable Output Frequency: 89.1 MHz/88.7 MHz l Anti-Shock & Vibration Mechanism 4 Optional Wireless Remote Control: l Disc and Track Mix and Repeat l Disc and Track Scan

n Power Requirement:

12 V DC Vehicle Battery
n Compact, Space-Saving Dimensions: l 25Ox64x178mm
x 2 l/2 x 7 in. (W x H x D) Fits in Many Gloveboxes Vertical, Horizontal, or 45 Installation

Precautions

The use of optical instruments with this product will increase eye hazard. Because the laser beam used in this compact disc changer is harmful to the eyes, do not attempt to disassemble the cabinet. Refer servicing to qualified personnel only. l This CD Changer is designed to be operated only on +12 volt DC negative ground systems. The unit cannot be used on +24 volt or positive ground systems. l If your vehicle was parked in direct sunlight resulting in a considerable rise in temperature inside the vehicle, allow the unit to cool off before operating your unit. The unit may not operate correctly in extremely hot or cold temperatures. The unit is equipped with a built in self protection circuit. When the temperature reaches a preset level, the protection circuit halts all unit operation. If this should happen, open a window and allow the car to cool. l You are cautioned that any changes or modifications not expressly approved in this manual could -. void your warranty. l If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer.

Before Installation and Testing the System
@I/<?#&*>@! To avoid the aggravation of costly mistakes and serious damage that could make you feel this way - please carefully follow all of the instructions. Youll be glad you did! General Recommendations l If youre not confident that you can install the unit correctly, have it installed by a qualified Blaupunkt installation technician. l Design and specifications subject to change without notice. l We recommend making all electrical connections and testing the system before installing the unit. 4
Before Installation and Testing (continued)
Transport Lock SCWWS The mechanism in the CD changer is locked into place during shipment by three transport screws. Be sure to remove the screws prior to testing the system and installation. To keep dust out of the unit, which could cause a malfunction, place the enclosed seals over the screw holes after the Transport Lock Screws have been removed. Reset Button A Reset Button is located on the front panel of the Commander and must be activated with a pen tip or other thin object, as it is recessed to prevent accidental engagement. Press the Reset Button under the following circumstances: 1. After connections have been made for initial testing. 2. After installation, when all wiring is completed. 3. If abnormal disc operation is encountered, the Reset Button should be pressed to clear the system to return to normaloperation. 4. After disconnecting and reconnecting the car battery, etc.
ID (Identity) Switch for 2nd CD Changer To connect a second CDC-RF 6 changer, you must use Blaupunkts CDC-RF BRIDGE, which is sold separately. When an additional CD changer has been connected using this unit, the ID switch is used to indicate the number of each respective changer unit.
The ID switch is initially set to 1 when shipped. l When only one changer is connected, the switch should be set to 1. l When two changers are connected, one of the units switches should be set to 2 using a ballpoint pen or similar fine-tipped tool.

CD 1st unit

2nd unit (additional changer unit)
Setting the Radio Frequency. You must select and test the radio frequency that the changer will use before you mount the FM Modulator. Set the radio frequency setting to 89.1 using the switch on the back of the FM Modulator. Test the operation of the changer. (See page 15) If a clear signal cannot be obtained on 89.1 MHz, change the position of the frequency-select switch to 88.7. The radio sensitivity is slightly reduced when the FM Modulator is connected.

Electrical Connections

Electrical Connections l Caution: before making connections, disconnect the ground wire terminal of the car battery to avoid shcrt circuits. l Use this unit only with negative ground 12 Volt (1 l- 16 Volt) direct current (DC). l Be sure to use the supplied changer cord. Using a cord other than the one supplied may cause noise or damage. l Be sure to connect the changer cord to the FM Modulator before mounting. If you attach the changer cord to the modulator and the cord projects down toward the back of the modulator, remove the cord and attach the other end of the cord to the modulator. Power Connections - To prevent short circuits and@ serious damage: l Disconnect the vehicle batterys negative terminal before making connections. Note - If the changer is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution to avoid causing a short circuit during installation. l Connect leads according to the wiring diagram. l Connect the yellow lead to a constant source of power which has passed through the vehicles fuse unit. l Connect the red power input lead only after the other leads are connected. And be sure to connect it to a positive (+) 12 Volt power terminal that is energized only when the ignition key is set to the accessory position or on position. l Connect the black lead to a grounded metal part of the vehicle. We recommend grounding all audio system black ground leads (head unit, external amplifier, etc.) to a common point.

Modulator

output

Yellow

Fuse 5A

To Battery Ip 0

DIN Connection Cord (6 pin)
Commander 11 Radio Antenna Input (in back)

(6 pin)

CD Changer

Installation

Recommendations l Carefully choose the mounting location so that the unit wont interfere with normal driving. l Avoid installing the unit it a place: - Subject to temperatures exceeding 55 degrees C (131 degrees F) (such as in a car parked in direct sunlight.) - Subject to direct sunlight - Subject to excessive vibration - Near heat sources (such as heaters and heat ducts) - Exposed to rain, moisture, excessive dirt and/or dust l This unit should not be installed in any way except that which is authorized (on its side, on its end, at a 45 angle or suspended). Installing it with its side facing down or upside down can cause malfunctioning. 1l The fuel tank must not be damaged by the installation. l The unit should not cover any wires or pipelines. l The unit (and its installation) should not damage or interfere with access to the spare tire, tools or other equipment in or under the trunk. l For a safe and secure installation, be sure to use only the supplied mounting hardware. l Press the reset button after completing the electrical connections and installation. The reset button is located on the front of the chassis (See page 5). l If you have any questions or problems concerning your unit that are not covered in this manual, please contact your Blaupunkt dealer. * l Be sure to remove the transport screws (See page 5). Anti-Vibration Setting l This unit can be installed horizontally (to the floor or suspended), vertically, and at a 45 angle. l Once the installation position has been chosen, set Anti-Vibration Setting Switches on both sides of the unit using a screwdriver. l The unit may skip if used with the wrong installation setting. Type of Installation Horizontal Suspended Vertical 45 angle Setting H H V 45

Mounting Hardware

Bracket (L)

Bracket (R)

Bracket (B)
(4) Hexagonal Bolt (M6 x20)
(4) Hexagonal Bolt With Washer

(4) Nut (M6)

(4) Tapping Screw (M5x 12) Tapping Screw (M3x12)
@q DIN 8 Pin Cable (1) Seal Double Sided Tape 7

Horizontal Installation

Confirm that Anti-Vibration Switches on both left and right sides are set to position H. l Attach bracket (L) and bracket (Ft) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6).
Pull back the carpet and determine where to attach the unit. Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing. Affix the unit to the floor by pressing in place.
Remove the hexagonal nuts and take off the changer.
Using a knife, cut xs in the carpet directly above the brackets (6) bolts. Return the carpet to its original position allowing the bolts to protrude through.
Once more, use the hexagonal nuts to attach the changer on top of the carpet.

Vertical Installation

onfinn that Anti-Vibration Switches on both left and right sides are set to position V, l Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (MS).
Once more, use the hexagonal nuts to attach the changer on top of the

45 Installation

Confirm that Anti-Vibration Switches on both left and right sides are set to position 45. l Attach brackets (L) and (R) using the hexagonal bolts (M5 x 8). l Attach brackets (L) and (R) to their respective brackets (B) using the hexagonal bolts (M6 x 20) and the hexagonal nuts (M6).
Pull back the carpet and determine where to attach the unit. l Stick the supplied double-sided tape to the bottom of the brackets (B) and peel off the paper backing. l Affix the unit to the floor by pressing in place.
Using a knife, cut Ys in the carpet directly above the brackets (B) bolts. Return the carpet to its original position allowing the bolts to protrude through.

Sumended Installation

Make sure that the unit does not hinder the movement of torsion bar spring or other parts of the trunk lid. l Confirm Anti-Vibration Switches on both the left and right sides are set to position H. l Attach bracket (L) and bracket (R) using the hexagonal bolts (M5 x 8).

Determine the mounting location and drill four mounting holes.

3.6 mm Diameter

Attach the CD changer with the tapping screws (M5 x 12).
Installation of the Controller
Peel off the removable seal on the back of the controller unit and install it in a location that will not obstruct driving.
Installation of the FM Modulator
install the FM Modulator to the floor or other surface with the included tapping screws (M3x12).

Changer Specifications

System Oversampling Laser Diode Frequency response Wow and Flutter THD (Total Harmonic Distortion). Dynamic Range Signal-to-Noise Ratio Channel Separation Current Drain Operating Temperature Dimensions Mass Power Requirement Part Number Optional Accessories CDC-RF6ir Wireless Remote Control CDC-RF6 Magazine Compact disc digital audio system 1 -Bit/8 X Oversampling GaALAs Double Hetero Type 20-l 5,000 Hz +/- 3 dB Below Measurable limit 0.1% 95 dB 90 dB 75 dB 0.4 A (During playback) 1.O A (During loading or ejecting a disc) -10to50C/14to122F 25Ox64x178mm 9 7/8 x 2 l/2 x 7 in. (W x H x D) Approximately 2.0 kg/4.4 tbs. 12 V DC Vehicle Battery (Negative Ground) FOOEB00020

FOOEB00021 FOOEBOOO15

Magazine & Compact Discs
Notes on the Disc Magazine Dirt, dust, scratches and warpage cause sound skips during playback and a deterioration of sound quality. Here are some suggestions on how to take care of your discs and the magazine:
Use compact discs that have the mark compact disc logo.

DIGITAL AUDIO

not use 3 (Scm) discs with the CDC-RF6k Handle the disc by its edge, and to keep the disc clean, do not touch the surface. l Do not leave the discs or the magazine in locations with high temperatures and high humidity, such as on a car dashboard or at the rear window where they will be subjected to direct sunlight or near heat ducts.-._ l Do not stick paper or write anything on the disc surface. l Do not drop the disc magazine or subject it to a violent shock. l Do not insert more than one disc at a time into a slot, otherwise the changer and the discs may be damaged. l Discs should be put back in their cases after use to avoid serious scratches that could cause the sound to skip.

l Do l

Cleaning Discs Before playing, remove fingerprints and dust the disc with a compact disc cleaning cloth. Wipe the disc from the center of the disc to the outer edge of the disc. Do not use solvents s&h as benzine, thinner, commercially available cleaners or anti-static spray intended for analog discs. Wipe in a straight motion from the inside to the outside of the disc. Although protective film is being marketed as a CD accessory, use of this type of product will result in malfunctions and should absolutely be avoided. Loading A Disc 1. Grip the tab on the magazines disc tray and pull out only one of the trays. 2. l Each tray can accommodate only one disc. l Put the disc in the tray with its play surface facing up and the printed (labeled) surface facing down. E-07 appears about 8 seconds if the disc is placed upside down. l Do not play 3 (8 cm) discs in this unit. 3. Press the tab on the disc tray to store the tray back in the magazine. Up to six discs can be loaded.

Play side up

Installing The Magazine 1. Slide the door toward the right. 2. Position the magazine so the top is facing up, and the arrow is facing the changer. Push it in until it clicks into place. Note: When the magazine is used for the first time, it will not lock into place unless the power supply has been connected. Make sure the door is closed. Otherwise, foreign matter may enter the unit, and contaminate the lenses inside the changer. When the magazine has been inserted into changer (or when the Reset Button on the Commander is pressed), the unit will automatically be activated and begin reading the infonation on the CDs, one CD at a time, until all of the CDs have been read. Ejecting The Magazine Press the Eject Button inside the unit to remove the magazine. Note: Be sure to close the door after inserting or removing the magazine. If dust or dirt enters the changer, it may cause a malfunction. Remove the magazine from the unit between uses during hot weather and when the CD changer is not used for long periods of time.

Location of Controls

1. Play/Pause Button Press to turn unit on, to temporarily pause play or to resume play. 2. DISC SELECT Button. Press to select the desired disc. 3. TRACK SELECT Button Press to select the desired track. Keep this button depressed during play for audible cue and review. 4. OFF Button Press to turn the unit off.

Operating Instructions

Before operating the unit for the first item (or after reconnecting the battery, etc.) press the Reset Button on the Commander. See page 5. Load the discs into the CD magazine and install the magazine into the CD charger. Turning Unit On/Playing A CD Vehicle ignition must be on. Turn on the car stereo and select FM band. Tune the radio to either 89.1 or 88.7 MHz. (depending on frequency chosen during installation). We suggest dedicating a Preset Radio Station Button to the frequency chosen during installation. To turn CD Changer on, press Play/Pause Button (1). The LCD panel on the controller will illuminate and show the Disc Number, the Track Number. Play of first disc will.begin. Pause Press the Play/Pause Button (1) during play. II appears on the displayand play is temporarily stopped. Press the button again to resume play starting from where it was stopped. When the pause mode is maintained for 5 minutes or more, the power will be automatically turned off. Turning Unit Off Press the OFF Button (4) to turn the unit off. The Commanders backlighting stays on. At The End Of The Disc When the last track on each disc is finished, the next available disc is automatically selected and play begins with the first track on the disc. When the last track on the last disc in the CD magazine is finished, the first disc is automatically selected and play begins with the first track on the disc. Moving To Another Track l To go to the next track, press and release the w Control (3). l To go back to the beginning of the track being played, press and release the w Control (3). l Press these controls repeatedly to locate previous or succeeding tracks. Audible Cue/Review l To move within a track, press and hold the w Control (3) for audible cue or the H1 control (3) for audible review. l The display flashes, and play is skipped to the desired part of a track in the forward or backward direction. l When the Track Select Button is kept depressed until the start or end of the disc is reached, the unit goes into a Pause mode. Switching to Another Disc Display the number of the disc to be heard using the Disc Select Button (2). l To advance to the next disc, press the right side of the Disc Select Button. l To return the previous disc, press the left side of the Disc Select Button.

Continued on Next Page

Optional Wireless Remote Control
The optional Wireless Remote CDC-RF6ir Control allows you to activate the following features in addition to the features that can be controlled with the CDC-RFGirs Wired Commander: /:
5. MIX Button This plays the tracks or discs in a random
sequence. 6. REPEAT Button This plays a certain track or disc over and 6 over again, 7. SCAN Button This plays the first portion of each track or disc. 8. CHANGER Button When two CD changers have been installed, use this button to select the changer whose CDs are to be played.

Mix Play

Track Mix - Press the MIX Button (5). MIX appears in the Display, and the tracks on the disc now heard are played in a random order. When all the l BLAUPUNKT tracks have been played, they will be played again, this time in a different CLXSRF6rr CONTROL m LX J random order. Disc Mix - When the MIX Button (5) is pressed for two seconds or more, DISC and MIX appear, the sequence in which the discs are to be played is first m-arranged and then the sequence in which the tracks are to be played is rearranged, after which the tracks on the first disc are played. When all the tracks on the first disc have been played, operation advances to the next disc. Press the MIX Button again to release the Mix Play function.

Repeat

Track Repeat - Press the Repeat Button (6). RPT appears in the display, and the track now heard is played repeatedly. Disc Repeat - When the Repeat Button (6) is pressed for two seconds or more, DISC and RPT appear, and the disc now heard is played repeatedly. Press the Repeat Button again to end Repeat play. Scan Track Scan - When thescan Button (7) is pressed, SCAN appears, and the first 10 seconds of each track on the selected disc are played in order. Disc Scan - When the Scan Button (7) is pressed for two seconds or more DISC and SCN appears, and the first 10 seconds of each track on each disc are played in order. Press the Scan Button again to end Scan play.
Switching TO A Second CD Changer (If connected)
If the CDC-RF BRIDGE (sold separately) is used, this CD changer system can accommodate an additional CDC-RF6 Changer. When two CD changers have been installed, the Changer Select Button (8) is used to select the desired changer. This button is not operational when only one CD changer has been connected.
Switching To Radio Or Tape
Press the OFF Button (4) to stop CD play, and listen to the radio or tape. Noise is heard and the reception deteriorates when listening to the radio without stopping CD play first. To resume CD play, set the radios FM frequency to 89.1 MHz or 88.7 MHz and press the Play/Pause Button (1). 16

Troubleshooting Guide

The following check will assist in the correction of most problems that you might encounter with your unit. Perform the checks described below before contacting your Blaupunkt dealer. Symptom No Power Fuse blown. Cause Remedy Replace with a fuse of the same type and rating as the original. If the fuse blows again, consult with your dealer. Check connections. Check connections. Set fader to center position to determine if speakers are wired for front or rear setting. Insert it in proper direction. Load disc with play side facing up. (Printed side should face down). Compare sound with another disc. If sound from second disc is acceptable, first disc is defective. Clean disc. Remove 3 screws on bottom of unit and try again. Set the Anti-Vibration Switch to the correct position (See page 7-l 1). Replace Battery. Clean the sensor and/or the controls lens.
Improper connection. No Sound No Sound, Two-Speak System Magazine cannot be installed. Selected disc does not play. Improper connection. Fader set to non-existent speakers.
Attempt made to insert magazine improperly. Disc is loaded incorrectly. Large scratches on disc or warped disc.
Noise is heard during playback or sound is intermittent.
Extemely dirty disc. Transit Screws still in place. Anti-Vibration Switch set in wrong position.
Wireless Remote Control does not work
Battery is dead. Commander ir sensor or Wireless Remote Control is dirty.
Fuse Replacement When replacing the fuse, be sure to use one with the correct amperage, which will be stated on the fuse case. Never use a fuse that has a stated amperage exceeding the one supplied for this unit, as this could cause malfunction and serious damage to the unit. Moisture Condensation On a rainy day or in a very damp area, moisture may condense on the lens inside the unit Should this occur, the unit will not operate properly. In this case, remove the disc and wait for about an hour until the moisture has evaporated.

Error Codes

If the changer malfunctions, one of the following error codes will be displayed: Error Display.I).. : 0 I. 111: : : :.: 1.W. : : 5 Cause Disc change malfunction. Disc loaded with print facing up or disc is dirty. Temperature inside car too hot. Magazine has not been installed. No discs in magazine. No discs in magazine No 2. Remedy Consult with dealer. Load disc properly. Clean disc. Allow the car to cool. Then press the Play/Pause Button. Install magazine. Load discs into magazine. Load discs into magazine No 2.

:.:.L I. :. I : 3 : e. 5.5 I. :.: :. :. II -4 : :.i I.! !. 1.1 HI.I :.: :.I.: :.p : :-: !! : k-1 5.: :.P

-: n.: -. I. :.

a BLAUPUNKT
Robert Bosch Corporation Sales Group-Blaupunkt Division 2800 South 25th Avenue, Broadview, Illinois 60153 Robert Bosch Inc. 6811 Century Avenue Mississauga, Ontario Canada L5N 1 Rl Robert Bosch S.A. de C.V. Dr. Lucia 270, Cols. Doctores, Mexico D. F. 06720
Copyright 1994 by the Robert Bosch Corporation No portion of this work may br reproduced in any form without the written consent of the Robert Bosch Corporation. Printed in Japan (12&l) 1 RAGPlOA71601

DPXTM PLUS DIGITAL PROTOCOL TECHNOLOGY APPLICATION GUIDE
MAKE/MODEL ACURA 3.2 TL CL Integra Legend MDX RL TL TSX Vigor YEAR(S) 2004-2006 1997-1999 1992-2001 1992-1995 2005-2006 1996-2001 1995-1998 2004-2006 1992-1994 PIE PART# HON03/PC-^^^ HON/PC-*** HON/PC-*** HON/PC-*** HON03/PC-^^^ HON/PC-*** HON-PC-*** HON03/PC-^^^ HON-*** LOCATION 14-Pin connector at headunit 8-Pin connector in trunk 8-Pin connector in trunk 8-Pin connector in trunk 14-Pin connector at headunit 8-Pin connector in trunk 8-Pin connector in trunk 14-Pin connector at headunit 8-Pin connector in trunk NOTES Not compatible if equipped with factory XM radio.
Not compatible if equipped with factory XM radio. Not compatible if equipped with factory Navigation. Not compatible if equipped with factory XM radio.
*** at the end of part # indicates that part is available for SAN and KNN (Sanyo-based and Kenwood CD Changers) ^^^ at the end of part # indicates that part is available for ALP, SAN, SON, and PIOX (Alpine, Sanyo-based and Sony CD Changer and Pioneer CD Changer/ XM receiver). Note 1: Uses 6- Disc Changer only. Note 2: HON03/PC-^^^ also requires PIE part # HON03-F/MM if vehicle is equipped with Navigation. AUDI Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. AVWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. A4 1998-2005 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. A6 1998-2005 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. A8 1998-2005 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. Allroad 2001-2005 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. Cabriolet 1998 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. RSVWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. S4 2000-2005 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. S6 2002-2003 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. S8 2001-2003 VWR/PC-*** 8-Pin connector at headunit Use Part # AUD/PC-*** if pre-wired with a 13-Pin DIN connector. TT 2000-2005 VWR/PC-*** 8-Pin connector at headunit A6/ A8/ QNot Compatible *** at the end of part # indicates that part is available for ALP, KNN, KNNSR, PAN, PIOX, SAN, and SON (Alpine, Kenwood, Panasonic, Pioneer, Sanyo, and Sony 6-Disc Changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Not compatible if vehicle is equipped with factory Navigation or Satellite. Note 2: 2002-Up models equipped with the Symphony II (6-disc in-dash) headunit will also require PIE Part# AA3-HAR. PIE Part# AA3-HAR is not required when using PIE Part# AUD/PC-*** BMW 3-Series 5-Series 5-Series 6-Series 7-Series 8-Series M M3 M5 X3 X5 Z3 Z4 Z8 1996-2006 1997-2003 2004-2007 2004-- Up 1996-1997 2000-2002 1996-2003 2000-2003 2004-2006 2001-2006 1996-2002 2003-2006 2000-2003 BMW/PC-*** BMW/PC-*** Not Compatible Not Compatible Not Compatible BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** BMW/PC-*** 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side Not compatible with models equipped with DSP. Not compatible with models equipped with DSP.
3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side 3 & 6-Pin connectors in rear driver side
Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP. Not compatible with models equipped with DSP.

*** at the end of part # indicates that part is available for ALP, KNNSR, PIOX, SAN, and SON (Alpine, Kenwood, Pioneer, Sanyo-based or Sony CD Changer, Pioneer XM or Kenwood Sirius receivers). BUICK Allure 2005-2007 GM12/PC-*** 12-Pin connector at headunit Must have XM/CD Changer ready headunit. Century 1997-2003 GM10/PC-KNW 10-Pin connector in trunk Century 2004-2005 GM12/PC-*** 12-Pin connector at headunit Must have XM/CD Changer ready headunit. LaCrosse 2005-2007 GM12/PC-*** 12-Pin connector at headunit Must have XM/CD Changer ready headunit. Le Sabre 1995-1999 GM10/PC-KNW 10-Pin connector in trunk Park Avenue 1995-2003 GM10/PC-KNW 10-Pin connector in trunk Rainier 2004-2006 GM12PC-*** 12-Pin connector at headunit Must have XM/CD Changer ready headunit. Regal 1995-2003 GM10/PC-KNW 10-Pin connector in trunk Rendezvous 2002-2007 GM12/PC-*** 12-Pin connector at headunit Must have XM/CD Changer ready headunit. Riviera 1996-1999 GM10/PC-KNW 10-Pin connector in trunk Roadmaster 1995-1996 GM10/PC-KNW 10-Pin connector in trunk Skylark 1996-1998 GM10/PC-KNW 10-Pin connector in trunk *** at the end of part # indicates that part is available for KNNSR or PIOX (Kenwood CD Changer/ Sirius receiver or Pioneer CD Changer/ XM receiver). Note 1: PIE Part# GM10/PC-KNW is not compatible with On-Star. Page 1 of 10 DPX-APP Revised: 07/30/07 Toll Free: Corporate Offices: Toll Free: Dealer Technical Support: (800) 526-8590 (800) 330-9754 Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net
MAKE/MODEL CADILLAC Catera* Deville Escalade Escalade EXT Seville YEAR(S) 1997-1999 1995-1999 1999-2002 2003-2006 2003-2006 1995-2001 PIE PART# GM10/PC-KNW GM10/PC-KNW GM9/PC-KNW GM12/PC-*** GM12/PC-*** GM10/PC-KNW LOCATION 10-Pin connector in trunk 10-Pin connector in trunk 9-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 10-Pin connector in trunk NOTES Not compatible with 2000-Up Catera.
Radio must have a BAND button. Radio must have a BAND button.

Radio must have a BAND button.
Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Use with PIE Part # COR-HAR if not pre-wired. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must be AM/FM/Cassette with TAPE/AUX button. Radio must have a BAND button.
Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button.
*** at the end of part # indicates that part is available for KNNSR or PIOX (Kenwood CD Changer/ Sirius receiver or Pioneer CD Changer/ XM receiver). Note 1: PIE Part# GM9/PC-KNW and GM10/PC-KNW is not compatible with On-Star. Note 2: GM9/PC-KNW not compatible with single DIN 6-disc (in-dash) slave CD Changer; GM9/PC-KNW takes the place of this 6-disc slave CD Changer. Note 3: GM12/PC-*** is compatible with Navigation (Touch and Non-Touch) screen radios. Note 4: GM radios 2000 and earlier are not capable of controlling two units; therefore, these radios will need to have the slave unit disconnected. Note 5: Not compatible if vehicle is equipped with factory Satellite. Note 6: 1995-1999 AM/FM/CD radios are not compatible. CHRYSLER 300 300M 300M 300M 2005-2006 1999-2001 2002-2004 2002-2004 Not Compatible CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX
8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit (800) 526-8590 (800) 330-9754
Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net
Page 2 of 10 DPX-APP Revised: 07/30/07
Toll Free: Corporate Offices: Toll Free: Dealer Technical Support:

MAKE/MODEL Cirrus Concorde Concorde Concorde Crossfire Grand Voyager LeBaron LHS LHS LHS LHS New Yorker Pacifica Pacifica PT Cruiser PT Cruiser PT Cruiser PT Cruiser Sebring Sebring Sebring Sebring Town & Country Town & Country Town & Country Town & Country Voyager Voyager Voyager Voyager YEAR(S) 1995-2000 1995-1997 1998-2001 2002-2005 2004-1995 1995-1998 1999-2001 2002-2004 2002-2004 1995-1996 2003-2006 2003-2002-2005 2002-1995-2002-2006 2002-2006 1995-2002-2006 2002-2001 2002-2004 2002-2004 PIE PART# CHRY/PC-*** CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ Not Compatible CHRY/PC-*** CHRY/PC-*** CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX CHRY/PC-*** CHRY02/PC-^^^ CHRY02/PC-PIOX CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX Not Compatible CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX L.OCATION 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit NOTES
Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button.
Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button.

Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button.
*** at the end of part # indicates that part is available for ALP, KNN, SAN (Alpine, Kenwood, or Sanyo-based CD Changer). ^^^ at the end of part indicates that part is available for ALP, KNN, KNNSR, SAN (Alpine, Kenwood CD Changer, Kenwood Sirius receiver, or Sanyobased CD Changer). Note 1: Not compatible with RBQ (6-disc in-dash), RB4 (Navigation), RAH and REV radios. Note 2: Not compatible if vehicle is equipped with factory Satellite radio. Note 3: CHRY/PC-*** - radio must be one of the following CD Changer controller headunits: 5-preset radio with 5-band EQ, "DISC ^" and "DISC v" on presets 1 and 5, and "MODE" button, 6-preset radio with Bass and Treble slider controls, "DIRECT DISC SELECT 1-6" printed above radio presets, and "MODE/EJECT" button. DODGE Avenger 1995-2000 Caliber 2006 Caravan 1995-2000 Caravan 2001 Caravan 2002-2006 Caravan 2002-2006 Charger 2006 Dakota 1995-2000 Dakota 2001 Dakota 2002-2004 Dakota 2002-2004 Dakota 2005-2006 Durango 1998-2000 Durango 2001 Durango 2002-2003 Durango 2002-2003 Durango 2004-2006 Grand Caravan 1995-2000 Intrepid 1995-1997 Intrepid 1998-2001 Intrepid 2002-2004 Intrepid 2002-2004 Magnum 2005-2006 Neon 1995-2000 Neon 2001 Neon 2002-2005 Neon 2002-2005 Ram 1995-2000 Ram 2001 Ram 2002-2005 Ram 2002-2005 Page 3 of 10 DPX-APP Revised: 07/30/07 CHRY/PC-*** 8-Pin connector at headunit Not Compatible CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit Not Compatible CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit Not Compatible CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit Not Compatible CHRY/PC-*** 8-Pin connector at headunit CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit Not Compatible CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit CHRY/PC-*** 8-Pin connector at headunit CHRY98/PC-^^^ 8-Pin connector at headunit CHRY02/PC-^^^ 10-Pin connector at headunit CHRY02/PC-PIOX 10-Pin connector at headunit Toll Free: Corporate Offices: (800) 526-8590 Toll Free: Dealer Technical Support: (800) 330-9754

Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button.
Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a CD-C button. Must be a Round Face radio with a MODE button. Must be a Round Face radio with a MODE button. Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net
MAKE/MODEL Ram Pickup Spirit Stealth Stratus Stratus Stratus Stratus Viper YEAR(S) 2006 1995-1995-1996 1995-2002-2005 2002-2005 1995-2000 PIE PART# Not Compatible CHRY/PC-*** CHRY/PC-*** CHRY/PC-*** CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ CHRY02/PC-PIOX CHRY/PC-*** LOCATION 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit NOTES
*** at the end of part # indicates that part is available for ALP, KNN, SAN (Alpine, Kenwood, or Sanyo-based CD Changer). ^^^ at the end of part indicates that part is available for ALP, KNN, KNNSR, SAN (Alpine, Kenwood CD Changer, Kenwood Sirius receiver, or Sanyobased CD Changer). Note 1: Not compatible with RBQ (6-disc in-dash), RB4 (Navigation), RAH and REV radios. Note 2: Not compatible if vehicle is equipped with factory Satellite radio. Note 3: CHRY/PC-*** - radio must be one of the following CD Changer controller headunits: 5-preset radio with 5-band EQ, "DISC ^" and "DISC v" on presets 1 and 5, and "MODE" button, 6-preset radio with Bass and Treble slider controls, "DIRECT DISC SELECT 1-6" printed above radio presets, and "MODE/EJECT" button. EAGLE Summit Talon Vision 1995-1996 1995-1998 1995-1997 CHRY/PC-*** CHRY/PC-*** CHRY/PC-*** 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit
*** at the end of part # indicates that part is available for ALP, KNN, SAN (Alpine, Kenwood, or Sanyo-based CD Changer). Note 1: Radio must be one of the following CD Changer controller headunits: 5-preset radio with 5-band EQ, "DISC ^" and "DISC v" on presets 1 and 5, and "MODE" button, 6-preset radio with Bass and Treble slider controls, "DIRECT DISC SELECT 1-6" printed above radio presets, and "MODE/EJECT" button. FORD Crown Victoria Crown Victoria Crown Victoria Crown Victoria Crown Victoria Escape Escape Escape Hybrid Escape Hybrid Econoline Econoline Escort Excursion Expedition Expedition Explorer Explorer Explorer Five hundred F-150 Pick Up F-Series Pick Up F150 F250 F350 F550 Focus Focus Freestar Freestyle HN80 HeavyDuty Mustang Mustang Mustang Ranger Ranger 2004 Models equipped with 6-Disc in-Dash, THX certified Navigation radio may use Part # FRD03/PC-*** 1995-1997 1995-1997 1998-2002 2003-2004 2005-2006 2001-2005 2004-1998-2005 1997-2003 2000-2005 1997-1998 1999-2002 1995-1997 1995-1997 1998-2004 2005-1998-2003 2004-2007 2005-2007 2005-2007 2005-2007 2000-2003 2005-2007 2004-2005 2005-2007 1996-1997 2001-2005-2006 1995-1997 1998-2004 FRDF/PC-*** FRDR/PC-*** FRDN/PC-*** FRD03/PC-*** Not Compatible FRDN/PC-*** FRD03/PC-*** FRDC/PC-*** FRDW/PC-*** FRDF/PC-*** FRDN/PC-*** FRDW/PC-*** FRDN/PC-*** FRDF/PC-*** FRDN/PC-*** FRDF/PC-*** FRDR/PC-*** FRDN/PC-*** Not Compatible FRDF/PC-*** FRDN/PC-*** Not Compatible Not Compatible Not Compatible Not Compatible FRDC/PC-*** Not Compatible FRD03/PC-*** Not Compatible FRDF/PC-*** FRDN/PC-*** FRD03/PC-*** Not Compatible FRDF/PC-*** FRDN/PC-*** 16-Pin connector at headunit 13 & 14-Pin connectors at RCU in trunk 20-Pin connector at headunit 16 & 24-Pin connectors at headunit 20-Pin connector at headunit 16 & 24-Pin connectors at headunit 12-Pin connector at headunit 12-Pin data cable under passenger seat 16-Pin connector at headunit 20-Pin connector at headunit 12-Pin data cable in trunk or rear 20-Pin connector at headunit 16-Pin connector at headunit 20-Pin connector at headunit 16-Pin connector at headunit 13 & 14-Pin connectors at RCU in trunk 20-Pin connector at headunit 16-Pin connector at headunit 20-Pin connector at headunit Premium Audio System. JBL or LUX Audio System. Use PIE Part # FRDW/PC-*** if pre-wired. Use PIE Part # FRDW/PC-*** if pre-wired. Must be an external CD Changer capable radio. Radio Model 3L8T-18C815-FB only. Navigation radio takes place of OEM CD Changer. Navigation radio takes place of OEM CD Changer.

Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button.
*** at the end of part # indicates that part is available for KNNSR or PIOX (Kenwood CD Changer/ Sirius receiver or Pioneer CD Changer/ XM receiver). Note 1: GM9/PC-KNW not compatible with single DIN 6-disc (in-dash) slave CD Changer; GM9/PC-KNW takes the place of this 6-disc slave CD Changer. Note 2: GM radios 2000 and earlier are not capable of controlling two units; therefore, these radios will need to have the slave unit disconnected. Note 3: Not compatible if vehicle is equipped with factory Satellite. Note 4: PIE Part# GM9/PC-KNW and GM10/PC-KNW is not compatible with On-Star. Note 5: 1995-1999 AM/FM/CD radios are not compatible. HONDA Accord Accord Accord Civic Civic 1992-1997 1998-2002 2003-2007 1992-1998 1999-2005 HON/PC-*** HON98/PC-^^^ HON03/PC-+++ HON/PC-*** HON98/PC-^^^ 8-Pin connector at headunit 14-Pin connector at headunit 14-Pin connector at headunit 8-Pin connector at headunit 14-Pin connector at headunit Use 6-disc CD Changer only. Use 6-disc CD Changer only. Compatibility includes Hybrid models. Not compatible if equipped with factory Satellite. Use 6-disc CD Changer only. Use 6-disc CD Changer only. Compatibility includes Si and Hybrid models.
Civic 2006 Not Compatible CRV 1997-1998 HON/PC-*** 8-Pin connector at headunit Use 6-disc CD Changer only. CRV 1999-2004 HON98/PC-^^^ 14-Pin connector at headunit Use 6-disc CD Changer only. CRV 2005-2006 HON03/PC-+++ 14-Pin connector at headunit Not compatible if equipped with factory Satellite. Del Sol 1993-1997 HON/PC-*** 8-Pin connector at headunit Use 6-disc CD Changer only. Element 2003-2006 HON03/PC-+++ 14-Pin connector at headunit Not compatible if equipped with factory Satellite. Odyssey 1995-1998 HON/PC-*** 8-Pin connector at headunit Use 6-disc CD Changer only. Odyssey 1999-2004 HON98/PC-^^^ 14-Pin connector at headunit Use 6-disc CD Changer only. Odyssey 2005-2007 HON03/PC-+++ 14-Pin connector at headunit Not compatible if equipped with factory Satellite. Pilot 2003-2005 HON98/PC-^^^ 14-Pin connector at headunit Use 6-disc CD Changer only. Pilot 2006-2007 HON03/PC-+++ 14-Pin connector at headunit Not compatible if equipped with factory Satellite. Prelude 1992-1998 HON/PC-*** 8-Pin connector at headunit Use 6-disc CD Changer only. Prelude 1999-2001 HON98/PC-^^^ 14-Pin connector at headunit Use 6-disc CD Changer only. S2000 2000-2003 HON98/PC-^^^ 14-Pin connector at headunit Use 6-disc CD Changer only. S2000 2004-2006 HON03/PC-+++ 14-Pin connector at headunit Not compatible if equipped with factory Satellite. *** at the end of part # indicates that part is available for KNN or SAN (Kenwood, or Sanyo-based CD Changer). ^^^ at the end of part # indicates that part is available for ALP, KNN, or SAN (Alpine, Kenwood, or Sanyo-based CD Changer). +++ at the end of part # indicates that part is available for ALP, PIOX, SAN and SON (Alpine, Pioneer, Sony and Sanyo-based CD Changer and Pioneer XM Receiver). Note 1: HON98/PC-^^^ - is not compatible with 1995 and up Passport or models equipped with 6-disc in-dash radios. Note 2: HON03/PC-+++ also requires PIE Part # HON03-F/MM if vehicle is equipped with Navigation. HUMMER H2 H2T H3 2003-2007 2004-2007 2005-2006 GM12/PC-*** GM12/PC-*** Not Compatible 12-Pin connector at headunit 12-Pin connector at headunit Radio must have a BAND button. Radio must have a BAND button.

*** at the end of part # indicates that part is available for KNNSR or PIOX (Kenwood CD Changer/ Sirius receiver or Pioneer CD Changer/ XM receiver). Note 1: PIE Part# GM12/PC*** is compatible with Navigation (Touch and Non-Touch) screen radios. Page 5 of 10 DPX-APP Revised: 07/30/07 Toll Free: Corporate Offices: Toll Free: Dealer Technical Support: (800) 526-8590 (800) 330-9754 Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net
MAKE/MODEL JAGUAR S Type S Type XJ12 XJ6 XJ8 XJR XJS *** YEAR(S) PIE PART# LOCATION NOTES
2000-2002 2000-1996-1996-1997 1996
JAGW/PC-*** JAG/PC-*** JAG96/PC-ALP JAG96/PC-ALP JAG96/PC-ALP JAG96/PC-ALP JAG96/PC-ALP
12-Pin connector in trunk 12-Pin connector at headunit 8-Pin connector in rear, drivers side 8-Pin connector in rear, drivers side 8-Pin connector in rear, drivers side 8-Pin connector in rear, drivers side 8-Pin connector in rear, drivers side
at the end of part # indicates that part is available for ALP, KNN, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Use 6-Disc CD Changer only. JEEP Cherokee Commander Grand Cherokee Grand Cherokee Grand Cherokee Grand Cherokee Liberty Wrangler Wrangler 1996-1996-1998 1999-2001 2002-2004 2005-2006 2002-2005 1997-1998 2002-2005 CHRY/PC-*** Not Compatible CHRY/PC-*** CHRY98/PC-^^^ CHRY02/PC-^^^ Not Compatible CHRY02/PC-^^^ CHRY/PC-*** CHRY02/PC-^^^ 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit 10-Pin connector at headunit 8-Pin connector at headunit 10-Pin connector at headunit
Must be 'Rounded Face' radio with a CD-C button. Must be 'Rounded Face' radio with a MODE button. Must be 'Rounded Face' radio with a MODE button. Must be 'Rounded Face' radio with a MODE button.
*** at the end of part # indicates that part is available for ALP, KNN, SAN (Alpine, Kenwood, or Sanyo-based CD Changer). ^^^ at the end of part indicates that part is available for ALP, KNN, KNNSR, SAN (Alpine, Kenwood CD Changer, Kenwood Sirius receiver, or Sanyobased CD Changer). Note 1: Not compatible with RBQ (6-disc in-dash), RB4 (Navigation), RAH and REV radios. Note 2: Not compatible if vehicle is equipped with factory Satellite radio. Note 3: CHRY/PC-*** - radio must be one of the following CD Changer controller headunits: 5-preset radio with 5-band EQ, "DISC ^" and "DISC v" on presets 1 and 5, and "MODE" button, 6-preset radio with Bass and Treble slider controls, "DIRECT DISC SELECT 1-6" printed above radio presets, and "MODE/EJECT" button. LANDROVER Discovery Freelander Freelander Range Rover *** 1998-2003 2001-2002 2003-2004 1998-2002 LND/PC*** LND/PC*** LNDR/PC*** LND/PC*** 10-Pin connector under front passenger seat 10-Pin connector under front passenger seat 10-Pin connector at headunit 10-Pin connector under front passenger seat

Visteon made radios only.
at the end of part # indicates that part is available for ALP, KNN, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). 2004 Models equipped with 6-Disc in-Dash, THX certified Navigation radio may use Part # FRD03/PC-*** 2002-2003 2004-2005 1995-1997 1995-1997 1998-2002 2000-2003 2004-2005 1995-1998 2006-2007 1997-1998 1999-2004-2005 1995-1997 1995-1997 1998-2002 2003-2004 2005-FRDN/PC-*** FRD03/PC-*** FRDF/PC-*** FRDR/PC-*** FRDN/PC-*** FRDN/PC-*** FRD03/PC-*** FRDF/PC-*** Not Compatible FRDF/PC-*** FRDN/PC-*** Not Compatible Not Compatible FRDF/PC-*** FRDR/PC-*** FRDW/PC-*** FRD03/PC-*** Not Compatible Not Compatible 20-Pin connector at headunit 16 & 24-Pin connectors at headunit 16-Pin connector at headunit 13 & 14-Pin connectors at RCU in trunk 20-Pin connector at headunit 20-Pin connector at headunit 16 & 24-Pin connectors at headunit 16-Pin connector at headunit 16-Pin connector at headunit 20-Pin connector at headunit Use PIE Part # FRDW/PC-*** if pre-wired. Must be an external CD Changer capable radio. Premium Audio System. JBL or LUX Audio System. Use PIE Part # FRDW/PC-*** if pre-wired. Must be an external CD Changer capable radio. Must be an external CD Changer capable radio. Must be an external CD Changer capable radio. Must be an external CD Changer capable radio. Must be an external CD Changer capable radio.
LINCOLN Aviator Aviator Continental Continental Continental LS LS Mark VIII Mark LT Navigator Navigator Navigator Navigator Town Car Town Car Town Car Town Car Town Car Zephyr ***
16-Pin connector at headunit 13 & 14-Pin connectors at RCU in trunk 12-Pin connector in trunk/center console 16 & 24-Pin connectors at headunit
Premium Audio System. JBL or LUX Audio System. Use PIE Part # FRDN/PC-*** at headunit if not pre-wired. Must be an external CD Changer capable radio.
at the end of part # indicates that part is available for ALP, KNN, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Not compatible if vehicle is equipped with factory Satellite or RSE (Rear Seat Entertainment). Note 2: Not compatible with 2003 and up 6-disc headunits if not equipped with external CD Changer capabilities. Page 6 of 10 DPX-APP Revised: 07/30/07 Toll Free: Corporate Offices: Toll Free: Dealer Technical Support: (800) 526-8590 (800) 330-9754 Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net

13 & 14-Pin connectors at RCU in rear passenger panel 16-Pin connector at headunit 20-Pin connector at headunit 13 & 14-Pin connectors at RCU in trunk or rear 12-Pin connector in trunk or rear 16-Pin connector at headunit 20-Pin connector at headunit
JBL or LUX Audio System. Premium Audio System. Must be an external CD Changer capable radio. Oval-Faced radio. Use PIE Part # FRDW/PC-*** at headunit if pre-wired. Must be an external CD Changer capable radio. Must be an external CD Changer capable radio.
*** at the end of part # indicates that part is available for ALP, KNN, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). *Note: If the 2001-2002 Villager is equipped with factory video system, use PIE Part # FRDW/PC-***. (Factory pre-wire found in lower back section of radio dash console). MERCEDES C Class CL Class CLK Class E Class ML Class S Class SL Class SLK Class MINI Cooper 2002-2006 BMW/PC-*** 3 & 6-Pin connectors in trunk 1996-1998 1996-1996-1998 1996-MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP MBZ/PC-ALP Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side Pre-wired 10-Pin connector in rear driver side
*** at the end of part # indicates that part is available for ALP, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo-based and Sony 6disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Not compatible if vehicle is equipped with DSP. NISSAN Quest Quest Quest 1997-1998 1999-2003 2004-2007 FRDF/PC-*** FRDN/PC-*** Not Compatible 16-Pin connector at headunit 20-Pin connector at headunit Must be an external CD Changer capable radio. Must be an external CD Changer capable radio.
*** at the end of part # indicates that part is available for ALP, KNN, KNNSR, PIOX, SAN and SON (Alpine, Kenwood, Pioneer, Sanyo-based and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: If the 2001-2003 Quest is equipped with factory video system, use PIE Part # FRDW-AUX. (Factory pre-wire found in lower back section of radio dash console) Page 7 of 10 Toll Free: Corporate Offices: (800) 526-8590 Visit Our Web Site: http://www.pie.net DPX-APP Revised: 07/30/07 Toll Free: Dealer Technical Support: (800) 330-9754 E-Mail Us: questions@pie.net

9-Pin connector at headunit 12-Pin connector at headunit 9-Pin connector at headunit 12-Pin connector at headunit 9-Pin connector at headunit 12-Pin connector at headunit 9-Pin connector at headunit 12-Pin connector at headunit 9-Pin connector at headunit 12-Pin connector at headunit
Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button. Radio must have a BAND button.
*** at the end of part # indicates that part is available for KNNSR or PIOX (Kenwood CD Changer/ Sirius receiver, or Pioneer CD Changer/XM receiver). Note 1: AM/FM/SINGLE CD headunits use 9-Pin data port for an OEM cassette deck and are not compatible with the GM9/PC-KNW. Note 2: Pontiac radios 2000 and earlier are not capable of controlling two units; therefore, these radios will need to have the slave unit disconnected in order to use the GM9/PC-KNW. SATURN All Models Relay SCION tC xA xB 2004-2006 2003-2006 2003-2006 TOY03/PC-*** TOY03/PC-*** TOY03/PC-*** 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 1995-1999 2005-2006 GM10/PC-KNW GM12/PC-*** 10-Pin connector in trunk 12-Pin connector at headunit Requires Saturn Part # 21023550 and Part # 21023253 if not pre-wired.
*** at the end of part # indicates that part is available for ALP, CLR, PIOX, SAN and SON (Alpine, Clarion, Pioneer, Sanyo-based and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Not compatible if equipped with factory Satellite. TOYOTA Avalon Avalon 1998-2002 2003-2006 TOY/PC-*** TOY03/PC-*** 12-Pin connector at headunit 12-Pin connector at headunit (800) 526-8590 (800) 330-9754 Visit Our Web Site: http://www.pie.net E-Mail Us: questions@pie.net
Page 8 of 10 DPX-APP Revised: 07/30/07
MAKE/MODEL 4Runner 4Runner Camry Camry Camry Solara Camry Solara Celica Celica Corolla Corolla Highlander Highlander Land Cruiser Land Cruiser Matrix MR2 MR2 RAV4 Sequoia Sequoia Sienna Sienna Tacoma Tacoma Tundra Tundra Yaris YEAR(S) 1998-2002 2003-2006 1998-2004 2005-2007 2000-2002 2003-2007 1998-2002 2003-2005 1998-2004 2005-2007 2001-2003 2004-2006 1998-2002 2003-2006 2005-2006 1998-2002 2003-2005 1998-2005 2000-2002 2003-2006 1998-2003 2004-2006 1998-2004 2005-2007 2000-2002 2003-PIE PART# TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY/PC-*** TOY03/PC-*** TOY03/PC-*** LOCATION 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit 12-Pin connector at headunit NOTES

*** at the end of part # indicates that part is available for ALP, CLR, PIOX, SAN and SON (Alpine, Clarion, Pioneer, Sanyo-based and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Not compatible with vehicles equipped with factory Navigation. Note 2: Not compatible if equipped with XM Rear Seat Entertainment (RSE) or 6-disc DVD Changer. VOLKSWAGEN Beetle Cabrio Eurovan Golf Golf GTI Jetta Jetta Passat Passat Phaeton Touareg 1998-2007 1998-2002 1999-2003 1998-2002 2003-2007 1999-2002 1998-1999 1999-2007 1998-2002 2003-2007 2004-2007 2004-2006 VWR/PC-*** VWR/PC-*** VWR/PC-*** VWR/PC-*** VW02/PC-*** VWR/PC-*** VWR-AUX VW02/PC-*** VWR/PC-*** VW02/PC-*** Not Compatible VW02/PC-*** 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 12-Pin connector at headunit. 8-Pin connector at headunit 8-Pin connector at headunit 12-Pin connector at headunit. 8-Pin connector at headunit 12-Pin connector at headunit. 12-Pin connector at headunit. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired. Use PIE Part # VW/PC-*** if pre-wired.
*** at the end of part # indicates that part is available for ALP, KNN, KNNSR, PAN, PIOX, SAN and SON (Alpine, Kenwood, Panasonic, Pioneer, Sanyo-based and Sony 6-disc changers, Pioneer XM or Kenwood Sirius receivers). Note 1: Parts ending with PAN require Panasonic data cable. Note 2: Panasonic 8-Disc CD Changer not compatible with 2000-2005 VW Premium V (Monsoon) radios identified by MID button next to volume knob. Note 3: Not compatible if equipped with factory Satellite. VOLVO C70 S40 S70 S80 S90 V40 V70 V1993-1997 1993-1997 1993-1997 1998-1998-2000 1999-2000 1997-1998-2000 1997-1998 VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP VOL/PC-ALP 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit 8-Pin connector at headunit
Note 1: Compatible with CR and SC series radios only.