02MilSRemMCarlMP28_gb.indd 31

About these instructions

These instructions contain important information to easily and safely install and operate the device. Read these instructions carefully and completely before using the device. Keep the instructions at a location so that they are always accessible to all users. Always pass on the device to third parties together with these instructions. In addition, observe the instructions of the devices used in conjunction with this device.

Use as directed

This device is intended for installation and operation in a vehicle with 12 V vehicle system voltage and must be installed in a DIN slot. Observe the performance limits in the technical data. Repairs and installation, if necessary, should be performed by a specialist.
Declaration of conformity
The Blaupunkt GmbH declares that the device complies with the basic requirements and the other relevant regulations of the directive 89/336/EWG.

Symbols used

These instructions employ the following symbols: CAUTION! Warns about laser beam DANGER! Warns about injuries CAUTION! Warns about damaging the CD drive The CE mark conrms the compliance with EU directives. u Identies a sequencing step Identies a listing
02MilSRemMCarlMP28_gb.indd 32

For your safety

The device was manufactured according to the state of the art and established safety guidelines. Even so, dangers may occur if you do not observe the safety notes in these instructions.
If you are installing device yourself
You may only install the device yourself if you are experienced in installing car sound systems and are very familiar with the electrical system of the vehicle. For this purpose, observe the installation instructions at the end of these instructions.

Observe the following!

CAUTION! The device contains a Class 1 laser that can cause injuries to your eyes. Do not open the device and do not perform any modications. DANGER! Increased risk of injury from connector In case of an accident, the protruding connector in the front AUX-IN socket may cause injuries. The use of straight plugs or adapters can lead to an increased risk of injury. It is, therefore, recommended to use angled jack plugs, e.g. the Blaupunkt accessories cable (001 535).

In operation: Operate the device only if trafc situation permits it! Stop at a suitable location to perform more extensive operations. Remove or attach the control panel only while the vehicle is standing an. To protect your hearing, always listen at a moderate volume. During mute phases (e.g. when changing the audio source), changing the volume is not audible. Do not increase the volume during this mute phase. Always listen at a moderate volume so that you can always hear acoustic warning signals (e.g. police). After operation: The device is worthless to a thief without the control panel. Always remove the control panel whenever you leave the vehicle. Transport the control panel so that it is protected against impacts and the contacts cannot become dirty.

Cleaning instructions

Solvents, cleaning and scouring agents as well as dashboard spray and plastics care product may contain ingredients that will damage the surface of the device. Use only a dry or slightly moistened cloth for cleaning the device.

Disposal of old unit

Do not dispose of your old unit in the household trash! Use the return and collection systems available to dispose of the old device.
02MilSRemMCarlMP28_gb.indd 33

30.01.2008 11:26:10 Uhr

Scope of delivery

Warranty

The scope of delivery includes: 1 Car sound system 1 Support frame 2 Disassembly tools 1 Perforated strips 1 Case 1 Operating instructions
We provide a manufacturer's warranty for products bought within the European Union. For devices purchased outside the European Union, the warranty terms issued by our respective responsible domestic agency are valid. The warranty terms can be called up under www.blaupunkt.com or requested directly from: Blaupunkt GmbH Hotline Robert-Bosch-Str. 200 D-31139 Hildesheim, Germany

Optional equipment

(not part of the scope of delivery) Use only accessories approved Blaupunkt. by
Remote control The steering wheel and/or handheld remote control allows you to access the basic functions of your car sound system safely and conveniently. You cannot switch the device on/off using the remote control! You can nd out from your Blaupunkt dealer or on the Internet at www.blaupunkt.com which remote controls can be used with your car sound system. Amplier You can use all Blaupunkt and Velocity ampliers.

Service

In some countries, Blaupunkt offers a repair and pick-up service. Information about the availability of this service in your country can be found at www.blaupunkt.com. If you want to take advantage of this service, you may request a pick-up service for your device via the Internet.

02MilSRemMCarlMP28_gb.indd 34

Detachable control panel

Theft protection
The device is equipped with a detachable control panel (ip-release panel) as a way of protecting your equipment against theft. The device is worthless to a thief without this control panel. Protect your device against theft by taking the control panel with you whenever you leave your vehicle. Do not leave the control panel inside your vehicle - not even in a hidden place. Notes: Never drop the control panel. Do not expose the control panel to direct sunlight or another heat source. Avoid direct skin contact with the control panels electrical contacts. If necessary, clean the contacts with a lint-free cloth moistened with cleaning alcohol.
Attaching the control panel
Detaching the control panel
u press the button 1. The control panel opens to the bottom.
u Insert the control panel on the right side and press it slightly to the right (see Figure 1.). u Carefully press the control panel into the left bracket until it engages (see Figure 2.). u Fold the control panel up into the slot and press it gently into place until it engages (see Figure 3.). If the device was still switched on when you detached the control panel, it will automatically switch on with the last setting activated (radio, CD or AUX) when the panel is replaced.
u Grasp the control panel at the left side. u Push the control panel slightly to the right and then pull it straight out of the bracket.
02MilSRemMCarlMP28_gb.indd 35
Notes: The device switches off as soon as the control panel is removed. The device remembers the audio source played last for the next switch-on. Any CD already inserted in the device remains there.

Timeout function

Activating/deactivating
The device features a time-out function (time window). For example, if you press the MENU button 3 and select a menu item, the device switches back after approx. 5 seconds after the last button activation. The settings performed are saved.

Switching on/off

You can switch on the device with any button.
To switch on the device, u press any button. The device switches on. u To switch off the device, press and hold down the On/Off button 6 for longer than 2 seconds. The device switches off.
Switching on/off using the vehicle ignition
The device will switch on/off simultaneously with the ignition if the device is correctly connected to the vehicles ignition as shown in the installation instructions and you did not switch the device off by pressing the On/Off button 6.
Switching off with detachable control panel

This device is equipped with an RDS radio receiver. Many of the receivable FM stations broadcast a signal that not only carries the programme but also additional information such as the station name and programme type (PTY). The station name appears on the display as soon as the tuner receives it.

Adjusting the tuner

To ensure proper functioning of the tuner, the device must be set for the region in which it is being operated. You can select between Europe ("EURO"), America ("USA") and Asia ("ASIA"). The tuner is factory-set to the region in which it was sold. If you experience problems with your radio reception, please check this setting. Note: The radio functions described in these operating instructions refer to the tuner setting for Europe (EURO). If you switch to a different region (ASIA, USA), the user settings are lost. u Press the MENU button 3. u Press the or button 2 repeatedly until "AREA EURO", "AREA USA" or "AREA ASIA" appears on the display. u Select your tuner region with the button ? or @. u Press the MENU button 3 or wait 5 seconds. The settings are saved.
02MilSRemMCarlMP28_gb.indd 38

Switching to radio mode

If you are in CD or AUX mode, u press the SRC button 4 repeatedly until an RDS radio name or a frequency appears on the display.
Your radio uses the Radio Data System (RDS). RDS allows receiving additional information on the radio frequency. In addition to the display of the station name, you can also use convenient RDS functions (see the next chapter). Note RDS is broadcast only in the FM band. Not all radio stations in the FM range offer RDS. Switching the display of station names on/off You can switch the display of the station names on or off as needed. In the delivery state, the function is activated. u Press the MENU button 3. u Press the or button 2 repeatedly until "RDS ON" or "RDS OFF" appears on the display. To switch RDS on/off, u press the button ? or @. When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved.
Convenient RDS functions (AF, REG) The convenient RDS functions AF (Alternative Frequency) and REG (Regional) extend the range of functions of your radio device. AF: If the RDS function is activated, the radio automatically tunes into the best receivable frequency for the station that is currently set. REG: At certain times, some radio stations divide their programme into regional programmes providing different content. You can use the REG function to prevent the car radio from switching to alternative frequencies that are transmitting different programme content. Note: AF and REG must be activated/deactivated separately in the menu. Switching AF on/off u Press the MENU button 3. u Press the or button 2 repeatedly until "AF ON" or "AF OFF" appears on the display. To switch AF on/off, u press the button ? or @. When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved.

Programme type (PTY)

Besides transmitting the station name, some FM stations also provide information on the type of programme that they are broadcasting. Your car radio can receive and display this information. For example, the programme types can be: CULTURE TRAVEL JAZZ SPORT SERVICE POP ROCK SCIENCE CHILDREN You can use the PTY function to select stations of a particular programme type. If you specify the programme type and start seek tuning, the radio will switch from the current station to a station of the selected programme type. Notes: If the tuner does not nd a station that corresponds to the selected programme type, you will hear a beep several times and "PTY NONE" appears briey on the display. The radio will then retune to the station that it received last. If the tuned radio station or another station on the broadcasting network broadcasts your selected programme type at a later point in time, the radio will automatically switch from the currently tuned station or from CD mode to the station whose programme type matches the one you selected. If you do not want this PTY switching, disable PTY in the menu.
Listening to stored stations
u Select the waveband or memory bank with the BAND button >. u Press one of the station buttons 1 - 6 =. The stored station is played if it can be received.
02MilSRemMCarlMP28_gb.indd 41

30.01.2008 11:26:11 Uhr

Trafc information
Switching PTY on/off u Press the MENU button 3. u Press the or button 2 repeatedly until "PTY OFF" or a selected programme (e.g. OLDIES, JAZZ, CLASSICS) appears on the display. u Press the ? or button @ to enable or disable PTY (PTY OFF). (The display shows the respective programme type.) When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved. Seek tuning starts immediately. During seek tuning, you cannot perform any menu settings. Note: As an alternative, you can switch PTY on/off with the TS button 9. To switch PTY on/off using the TS button 9, u press the TS button 9 for longer than 2 seconds. PTY switches on/off.

Switching to CD mode

If there is no CD inserted in the drive, u press the button 1. The control panel opens.
02MilSRemMCarlMP28_gb.indd 43
u Gently insert the CD with its printed side uppermost into the drive until you feel some resistance. The drive draws in the CD automatically. You must not hinder or assist the drive as it draws in the CD. u Gently close the control panel whilst exerting a little pressure until you feel it click into place. The CD starts playing. Note: If the vehicle ignition was switched off prior to inserting the CD, you must switch the device on rst with the On/ Off button 6 to start the playback. If a CD is already inserted in the drive, u press the SRC button 4 repeatedly until the "CD symbol" appears on the display. The playback starts with the track played last.

Random track play (MIX)

To play back all the tracks of a CD at random, u press the 4 MIX button =. The display shows "MIX". The next randomly selected track will then be played. Cancelling MIX u Press the 4 MIX button = again. The MIX symbol disappears. Normal playback is then resumed.

Scanning tracks (SCAN)

You can scan (briey play) all the tracks on the CD. u Press the 2 SCN button =. The display shows "SCN". The next track will then be scanned. Stopping Scan To end the scanning process, u press the 2 SCN button =. The SCN symbol disappears. The currently scanned track will then continue to be played normally. Adjusting the scan time for SCAN You can adjust the scan time for the SCAN function in the menu. u Press the MENU button 3. u Press the or button 2 repeatedly until "SCAN" appears on the display. u Press the ? or button @ to select either 5, 10 or 20 seconds.

Selecting tracks

u Press the ? or button @ to select the next or previous track. If you press the button @ once, the current track will be played again from the beginning.

Fast searching (audible)

To fast search backwards or forwards, u press and hold down the ? or button @ until fast searching backwards or forwards begins.
02MilSRemMCarlMP28_gb.indd 44
Repeating tracks (REPEAT)
If you want to repeat a track, u press the 3 RPT button =. The display shows "RPT". The track is repeated continuously until you deactivate Repeat. Cancelling Repeat If you want to cancel the repeat function, u press the 3 RPT button = again. The RPT symbol disappears. Normal playback is then resumed.

Interrupting playback (PAUSE)
To interrupt the playback, u press the 1 button =. The display shows "PAUSE". Cancelling pause To continue the playback, u press the 1 button = during the pause. Playback is continued.
Trafc announcements in CD mode
If you wish to receive trafc announcements in CD mode, u press the TA button <. The priority for trafc announcements is activated if the display shows the TA symbol. For further details, please read the chapter entitled "Trafc information".

Ejecting a CD

u Press the button 1. The control panel opens to the bottom.
02MilSRemMCarlMP28_gb.indd 45
When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved.

Conguring the display

Notes: The display can be changed only if RDS is switched on in the menu. The display changes for 5 seconds. You can choose from various display options in CD mode: Time Station set last (only for RDS station name reception) Frequency set last PTY function set last CD track display To switch between the different display options, u press the DIS button 8 repeatedly until the desired display appears.

MP3/WMA mode

u Press the button C next to the CD compartment. The CD is ejected. u Remove the CD and close the control panel. Notes: If a CD is ejected, the drive will automatically draw it back in again after 10 seconds. You can also eject CDs whilst the device is switched off or whilst another audio source is activated.
You can also use this car sound system to play CD-Rs and CD-RWs that contain MP3 music les. You can also play WMA les. This chapters deals only with playing MP3 les since the operation for MP3 and WMA les is identical. Note: WMA les with Digital Rights Management (DRM) from online music shops cannot be played with this device.

Preparing an MP3/WMA CD

The various combinations of CD burners, CD burning software and CD blanks may lead to problems arising with the devices ability to play certain CDs. If problems occur with your own burned CDs, you should try another brand of CD blank or choose another colour of CD blank. The format of the CD must be ISO 9660 Level 1/Level 2 or Joliet. Other formats cannot be played reliably. Notes: To ensure uninterrupted playback, do not try changing the le extension to ".MP3" of any les other than MP3 les and then attempt to play them. The device will ignore these invalid les during playback. do not use "mixed" CDs containing both non-MP3 les and MP3 tracks (the device only reads MP3 les during MP3 playback).
02MilSRemMCarlMP28_gb.indd 46
do not use mix-mode CDs containing both CD-audio tracks and MP3 tracks. If you try playing a mix-mode CD, the device will only play the CDaudio tracks. MP3 ID3 tags MP3 tracks can contain additional information such as the artist, album and track name (ID3 tags). This device can display ID3 tags of version 1 and 2.

Switching to MP3 mode

MP3 mode is activated in the same way as normal CD mode. For further information, please read the section entitled "Switching to CD mode" in the "CD mode" chapter. Note If an MP3 or WMA CD is located in the drive, the display shows "MP3" during MP3 mode.
Conguring the default display You can display various types of information on the current track: Time Track Name of artist Genre Station set last PTY function set last File name To switch between the different display options, u press the DIS button 8 repeatedly until the desired display appears.

Selecting a directory

To move up or down to another directory, u press the or button 2 once or several times.
The following settings require that an MP3 CD is in the device. Notes: You can change the display for time, station set last and PTY function set last only if RDS is switched on in the menu. The display changes for 5 seconds.

Selecting tracks/les

To move up or down to another track or le in the current directory, u press the ? or button @ once or several times. If you press the button @ once, the current track will be played again from the beginning.
To fast search forwards or backwards, u press and hold down the ? or button @ until fast searching backwards or forwards begins.
02MilSRemMCarlMP28_gb.indd 47

30.01.2008 11:26:12 Uhr

To repeat a track, u briey press the 3 RPT button =. The display shows "RPT". The track is repeated continuously until you deactivate Repeat. To repeat a directory, u press the 3 RPT button = for longer than 2 seconds. "RPT" ashes on the display. The directory is repeated continuously until you deactivate Repeat. Cancelling Repeat If you want to cancel the repeat function, u Press the 3 RPT button = again. The RPT symbol disappears. Normal playback is then resumed.
You can scan (briey play) all the tracks on the CD. u Press the 2 SCN button =. The display shows "SCN". The next track will then be scanned. Stopping Scan To end the scanning process, u press the 2 SCN button =. The SCN symbol disappears. The currently scanned track will then continue to be played normally. Adjusting the scan time for SCAN You can adjust the scan time for the SCAN function in the menu. u Press the MENU button 3. u Press the or button 2 repeatedly until "SCAN" appears on the display. u Press the button ? or button @ to select either 5, 10 or 20 seconds.
u Press the 1 button =. The display shows "PAUSE". Cancelling pause button = during the u press the 1 pause. Playback is continued.
02MilSRemMCarlMP28_gb.indd 48

Menu settings

Setting the time
To set the time, u press the MENU button 3. u Press the or button 2 repeatedly until "CLOCK ON" or "CLOCK OFF" appears on the display. You can adjust the time and time mode only if the menu item is set to "CLOCK ON". u Press the MENU button 3. u Press the or button 2 repeatedly until the time appears on the display. ? or button @ to u Press the change the value. u Press the or button 2 to switch between hours and minutes. Note: If the menu item is set to "CLOCK ON", the device displays the time for all selected sources. The time adjusts itself automatically with the RDS signal if it can be received. When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved.

Selecting 12/24-hour clock mode
u Press the MENU button 3. u Press the or button 2 repeatedly until "HOUR 24" or "HOUR 12" appears on the display. ? or button @ to u Press the switch the mode. When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved.
Loading standard settings
Note: Your user settings (audio, station memory) are overwritten when you load the standard settings. To load the standard settings, u press the MENU button 3. u Press the or button 2 repeatedly until "DEF OFF" appears on the display. u Press the ? or button @ until "DEF LOAD" (default load) appears on the display. u Press the MENU button 3 within 5 seconds (timeout function) to load the standard settings.
02MilSRemMCarlMP28_gb.indd 49
Switching the AUX input on/off
You can switch the AUX input on/off in the menu. u Press the MENU button 3. u Press the or button 2 repeatedly until "AUX ON" or "AUX OFF" appears on the display. ? or button @ to u Press the switch the AUX input on/off. When you have nished making your changes, u press the MENU button 3 or wait 5 seconds. The settings are saved. Note If the AUX input is switched off in the menu, you cannot select the AUX input as a source.
The sound settings for the volume distribution (balance and fader), X-BASS, bass, treble and DSP (Digital Sound Processor) apply to all the audio sources.

Adjusting the bass

You can adjust the bass level between -10 and +10. Adjusting the level u Press the AUD button : repeatedly until "BAS" appears on the display. u Turn the volume control 5 to adjust the level from -10 to +10. When you have nished making your changes, u wait 5 seconds. The settings are saved. Note: If an equalizer presetting (POP M, ROCK M, CLASSICS, FLAT) is selected, the manual increase of the bass level and treble is overwritten. As soon as another manual increase is performed, the equaliser switches off. For further information, please read the note in the section entitled "Equalizer presettings (presets)".
Adjusting the display brightness
To switch between bright and dark, u press and hold down the DIS button 8 for longer than 2 seconds.

Adjusting the treble

You can adjust the treble level between -10 and +10.
02MilSRemMCarlMP28_gb.indd 50
Adjusting the level u Press the AUD button : repeatedly until "TRB" appears on the display. u Turn the volume control 5 to adjust the level from -10 to +10. When you have nished making your changes, u wait 5 seconds. The settings are saved. Note: If an equalizer presetting (POP M, ROCK M, CLASSICS, FLAT) is selected, the manual increase of the bass level and treble is overwritten. As soon as another manual increase is performed, the equaliser switches off. For further information, please read the note in the section entitled "Equalizer presettings (presets)".

Adjusting the front/rear volume distribution (fader)
To adjust the front/rear volume distribution (fader), u press the AUD button : repeatedly until "FAD" appears on the display. u Turn the volume control 5 to adjust the distribution from 10F to 10R. When you have nished making your changes, u wait 5 seconds. The settings are saved.

X-BASS

X-Bass allows you to increase the bass at low volume. The selected X-Bass setting is effective for all audio sources (radio, CD, MP3 or AUX). Switching X-BASS on/off u Press the AUD button : repeatedly until "X-BASS ON" or "X-BASS OFF" appears on the display. u Turn the volume control 5 to perform the desired setting. When you have nished making your changes, u wait 5 seconds. The settings are saved. "X-BASS" appears on the display if the function is activated.
Setting the left/right volume distribution (balance)
To adjust the left/right volume distribution (balance), u press the AUD button : repeatedly until "BAL" appears on the display. u Turn the volume control 5 to adjust the distribution from 10L to 10R. When you have nished making your changes, u wait 5 seconds. The settings are saved.
02MilSRemMCarlMP28_gb.indd 51

External audio source

Equalizer presettings (presets)
This device features an equaliser in which the settings for "FLAT" (linear) and the music genres "CLASSICS", "POP M" and "ROCK M" are already programmed. To select an equaliser setting, u press the AUD button : repeatedly until "FLAT", "CLASSICS", "POP M", "ROCK M" or "DSP OFF" appears on the display. u Turn the volume control 5 to select one of the settings or select "DSP OFF" to switch off the equaliser. When you have nished making your changes, u wait 5 seconds. The settings are saved. The respective setting appears on the display. Note: Without equaliser presets, you can adjust the bass and treble from -10 to +10. If you change the treble and/or bass while an equalizer presetting (POP M, ROCK M, CLASSICS, FLAT) is selected, the equaliser switches off automatically (DSP OFF).

Mitgelieferte Montage- und Anschlussteile Supplied Mounting Hardware Materiel de montage fourni Componenti di ssaggio comprese nella fornitura Meegeleverde montagematerialen Medfljande monteringsdetaljer
Als Sonderzubehr erhltlich Available as an optional accessory Disponible en option Reperibili come accessori extra Als speciale accessoire verkrijgbaar Tillval Preamp./Sub./Center - out cable

001 512

Einbaustze Installation kits Kits de montage Set di montaggio Inbouwsets Monteringssatser

3. 0- 30

7 608.
B1_EA_MiSReMCarMP28.indd 160

Antenna

182 53
AUX IN only San Remo MP28 Monte Carlo MP28
B1_EA_MiSReMCarMP28.indd 161
Ausbau / Removal / Dmontage / Smontaggio / Demontage / Urmontering

C-1 C-2

10 Ampere
NC Radio Mute NC Permanent +12V NC NC Kl.15/Ignition Masse/GND 7 8
Speaker out RR+ Speaker out RR Speaker out RF+ Speaker out RF Speaker out LF+ Speaker out LF Speaker out LR+ Speaker out LR
Line Out LR Line Out RR Line Out / Ground NC NC NC 11 12
NC NC NC SW Supply - RC +12V Remote Control RC - GND 19 20

NC NC NC NC NC NC NC NC

B1_EA_MiSReMCarMP28.indd 162
Preamp./Sub./Center - out cable 001 512

Kl. 15 +12V GND

Radio Mute

F LR RF L

+ + + + -

4 Ohm 4 Ohm 4 Ohm 4 Ohm

nderungen vorbehalten! Subject to changes! Sous rserve de modications! Modiche riservate! Wijzigingen voorbehouden! ndringar frbehlles!
B1_EA_MiSReMCarMP28.indd 163

04.02.2008 13:29:49 Uhr

2008 All rights reserved by Blaupunkt. This material may be reproduced, copied or distributed for personal use only. This product is protected by certain intellectual property rights of Microsoft. Use or distribution of such technology outside of this product is prohibited without a license from Microsoft.
B1_EA_MiSReMCarMP28.indd 164
Bitte den ausgefllten Gertepass sicher aufbewahren! Please keep the lled-in radio pass in a safe place! Prire de conserver soigneusement la carte dautoradio remplie ! Tenete per favore il libretto di apparecchio, debitamente riempito, in un posto sicuro! Bewaar de ingevulde apparaatpas op een veilige plaats! Vnligen frvara ifyllt apparatpass p sker plats!
B1_EA_MiSReMCarMP28.indd 165

Country:

Germany Austria Belgium Denmark Finland France Great Britain Greece Ireland Italy Luxembourg Netherlands Norway Portugal Spain Sweden Switzerland Czech. Rep. Hungary Poland Turkey USA Brasil (Mercosur) Malaysia (Asia Pacic) (D) (A) (B) (DK) (FIN) (F) (GB) (GR) (IRL) (I) (L) (NL) (N) (P) (E) (S) (CH) (CZ) (H) (PL) (TR) (USA) (BR)

Phone:

0180-5000225 01-0 02-360 09-01-01-01-700 02-+70 08-7501850 01-8471644 02-704 0800-118922 0212-23 800-950-7045446

+55-2773 +604-6413 640

(MAL) +604-6382 474

Gertepass

Typ: Serien-Nr:

7 648...

Blaupunkt GmbH, Robert-Bosch-Strae 200, D-31139 Hildesheim
B1_EA_MiSReMCarMP28.indd 166

8622405789

01/08 - CM-AS/SCS1 (dt, gb, fr, it, nl, sw)
05121-http://www.blaupunkt.com 01-391 02-44-09-01-01-01-706 02-+08-7501810 01-8471650 02-022-8771260 0212-40 708-6817188