2 VOL+ / VOLTo alter the volume. Each time the set is switched on, it will play with the pre-adjusted volume (VOL FIX). You may also change the VOL FIX setting (see chapter DSC programming).
Switching on with the ignition being switched off: To keep on operating the set when the ignition is switched off (KeyCard is inserted), proceed as follows: Press ON after the double beep tone. The unit will be turned on. To avoid that the battery goes flat, the system will be turned off automatically after a playback time of one hour.
To programme the mute volume level, proceed as follows: Adjust the desired volume. Press for two seconds until you hear a beep. Now this volume level is stored as your mute volume.

DEUTSCH

Quick reference
6 Rocker switch Radio operation CD operation Changer operation (optional)
Station search Up Down <</>> Up/Down in short intervals when AF is off <</>> To scroll through the station networks when AF is on, e.g. NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE.
Up Down Press once to go back to the beginning of the current title. Fast advance, audible (CUE). Hold down as long as required. Fast reverse, audible (REVIEW). Hold down as long as required.

Title selection

CD selection Up Down Title selection Upwards: Press briefly. CUE - fast advance (audible): Keep depressed. Downwards: Press as many times as required. To restart a title: Press briefly. REVIEW - fast reverse (audible): Keep depressed.
Extra rocker switch functions: Further setting functions with AUD D GEO C DSC MODE B PTY > Condition: The corresponding function has to be activated. 32

7 Display

m) PTY n) MIX o) TPM p) T5
9 SC/MIX Radio operation Scan Press SC/MIX briefly FM SCAN and the name of the scanned station will alternately appear in the display. The unit will scan all stations which can be received. Preset Scan Press SC/MIX for approximately two seconds until you hear a beep. SCAN and the name of the scanned station will alternately appear in the display. The unit will scan all stations stored on the preset buttons. To stop Scan / Preset Scan: Press SC/MIX once again. CD operation MIX playback The Mix function is switched on if MIX appears in the display. The CD tracks will be played at random. To switch Mix on and off: Press SC/MIX briefly. 33

e f g hi j k l m

KeyCard
For this purpose, introduce the KeyCard (with the contact area showing up) into the slot above the tongue sticking out of the unit. To remove the card, press first to unlock. Read also the information in chapter KeyCard theft protection system. Flashing KeyCard tongue When the radio is turned off and the KeyCard removed, the KeyCard tongue can be programmed to flash for optical theft protection. For more information see chapter DSC programming.

a) NDR2 - Station name b) VIVALDI - CD name or c) 1 : 52 - CD time (playback time) and number for changer operation (optional) d) FM - Waveband e) 6 - Preset button (1-6) f) I, II, T - Memory bank I, II or Travelstore g) CD-IN - A CD is inserted - Stereo h) i) lo - Seek tuning sensitivity j) AF - Alternative frequency for RDS operation k) TA - Priority for traffic stations l) TP - A traffic station is being received
8 KeyCard theft protection system To operate the set it is necessary that the KeyCard is inserted.
- Programme type function - CD playback in random order - To select and store CD titles - Track no. 5 is played back
This flashlight can be switched off by pushing in the tongue and lock.
CD-Scan Press SC/MIX for approximately two seconds until you hear a beep. CD-SCAN appears in the display. The unit will scan all CD titles. To stop CD-Scan: Press SC/MIX once again. Changer (CDC) operation (optional) MIX CD The CD titles will be played at random. The individual discs are selected in numeric order. MIX MAG The CD titles will be played at random. The individual discs are also selected in random order. MIX OFF The Mix function is deactivated. Press SC/MIX as many times until the desired function briefly appears in the display. CD-Scan Press SC/MIX for approximately two seconds until you hear a beep. CDC-SCAN will appear in the display. All CD titles will be scanned briefly. 34
To stop CD-Scan: Press SC/MIX once again. : loCLR Radio operation To switch the seek tuning sensitivity level: Press button briefly. To switch between mono and stereo reception: Press button for approximately two seconds (beep). The stereo symbol will disappear for mono playback. CD and CDC operation (optional) To clear CD titles from the TPM memory. ; TPM (Track Program Memory) To select and store titles during CD/ CDC playback. In each operating mode it is possible to manage a maximum of 30 discs. Please refer to chapter TPM programming.
< TA (priority for traffic announcements) When TA lights up in the display, the system will play traffic stations only. Priority on/off: Press TA. = AF Radio operation Alternative frequency during RDS operation: When AF lights up in the display, the system will automatically seek a frequency offering better reception of the same RDS programme. AF on/off: Press AF briefly. Regional function on/off: Press the AF button for approximately two seconds until you hear a beep. REG-ON or REG-OFF will appear in the display (see chapter REG - regional programme). CD operation To switch between the name and time (playback time) display modes: Press AF briefly.
CDC operation (optional) To switch between the name, time (playback time) and number (CD number) display modes: Press AF briefly. > PTY (Programme Type) In the PTY mode, the preset buttons become programme type buttons. With each preset you can select one programme type, such as for example NEWS, SPORT, POP MUSIC, EDUCATE, etc. ? SRC SRC (source) When having a CD inserted you can switch between the different audio sources radio, CD, and CDC/AUX (if activated). (Eject) Hold down the button for approximately two seconds (beep) and the CD will eject.

Installation

If you would like to install your new car stereo yourself or add other audio components to existing ones, then please read carefully the enclosed instructions on installation and connection. In order to ensure that the set operates properly it is necessary that the positive power supply line is connected via the ignition and the permanent +12 V lead. Do not ground the loudspeaker outputs!

Accessories

Use only the accessories and spare parts approved by Blaupunkt. You can use the following Blaupunkt products with this car stereo: Changer CDC A 05 or CDC F 05 Remote control With the infrared remote control RC 05 you can control all of the important functions of your car hi-fi system from the steering wheel.

Traffic safety

As the driver of a motor vehicle, it is your responsibility to pay attention to the traffic situation at all times. Never use your car radio in a way that could distract you. Please keep in mind that you travel a distance of 14 m per second at a speed of only 50 km/h. Should the traffic situation become particularly demanding, we advise you not to use the radio. Always make sure that you are still able to hear any warning signals coming from outside of the vehicle, such as police or fire engine sirens, so that you can react accordingly. Therefore, you should always select a moderate volume for playing your car radio while you are driving.

Telephone mute

If you have a mobile telephone installed in your vehicle, radio or CD playback can be muted automatically when using the phone (telephone mute). PHONE will then appear in the display. When TA is active, traffic messages will always have priority. The announcement will be aborted by pressing the TA button.
Amplifier All Blaupunkt amplifiers

Important notes

KeyCard theft protection system
This car radio is supplied with one KeyCard as standard, though it can also be operated with a second card. If you have lost your KeyCard or if it was damaged, you can buy a new one from your specialised dealer. When using two KeyCards, the settings stored on the first card will be adopted. However, you can individually store the following functions: Preset button assignments, bass, treble, balance and fader settings, Loudness, TA (traffic announcement volume), beep volume. In addition, the settings activated before switching the radio off, such as the waveband, station, TA priority, AF, REG ON/OFF, SCANTIME, seek tuning sensitivity and VOL FIX will also remained stored. This ensures that you will find your basic settings re-adjusted automatically as soon as you have inserted your KeyCard. ERR will appear in the display. In this case please do not make any further adjustments. The system will switch off after approximately ten seconds. When inserting another card type (e.g. phone or credit card), the display will show WRONG KC for approximately two seconds. Remove the wrong card and introduce the correct KeyCard. After the display indications CARD ERR or WRONG KC: Press ON to turn on the set. Press << or >>. The display will switch to CHANGE. Push in the KeyCard. The card is released and put in the proper position for being removed. Remove the first KeyCard and insert the new one while CHANGE is still being displayed. After the display indication READY or LEARN KC, press DSC. Now you can also use the new KeyCard for operating your unit. A maximum of two cards can be used for the set. When trying to train a third one, the access authorisation for the KeyCard not used for the training process will be deleted automatically.

Station tuning

Automatic tuning / Press / ; the car radio will automatically search for the next station. When keeping the upper or lower part / of the rocker switch depressed, seek tuning will speed up in upwards or downwards direction.
Scrolling through the broadcasting networks (only FM)
You can use the << >> buttons to tune in stations of your reception area. If several programmes of the broadcasting networks can be received, you can scroll through them in forwards direction pressing >>, or backwards using the << button, e.g. NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE. For this it is necessary that the stations have been tuned in at least once and that AF is active (lights up in the display). For this purpose, you may start Travelstore seek operation: Press FMT for two seconds; the system starts to run through the frequency band. If AF does not light up, press AF. With this, the requirements for selecting stations with << >> are fulfilled.
Press the FMT button as many times until the desired memory bank lights up in the display.

Storing stations

On FM, you can store six stations on the preset buttons 1-6 for each of the memory banks I, II and T. On MW/LW, you can store six stations each. Select the appropriate waveband with FMT or ML. Tune in a station with the rocker switch (either automatically / or manually << >>).
Manual tuning with << >> You can also tune in a station manually. Condition: AF and PTY must be switched off (i.e. the symbols do not light up in the display). If necessary, deactivate these functions: Press AF or PTY. Manual tuning: Press << >>; the frequency will change in short intervals in downwards or upwards direction. When holding the right or left part of the rocker switch depressed, the frequency scan is speeded up.
Changing the memory bank (FM) Notice:
You can shift between the memory banks I, II and T in order to store stations and recall them later. The currently selected memory bank is indicated in the display. Should you tune in a station which has already been stored before on another memory bank, the corresponding preset button and the memory bank will briefly flash in the display.

PTY Programme Type

If the system is unable to find a station offering the selected programme type, the display will show NO PTY and a beep tone will be released. The station received before starting seek tuning will be tuned in. You can assign different programme types to each preset position. Please refer to the next chapter Storing programme types. b) Using the << >> buttons of the rocker switch When PTY is switched on, you can select a programme type using buttons << >>. Press << or >>; the programme type selected last will be displayed for three seconds. During this period press >> (forwards) or << (backwards) to select the desired type. Press << or >> as many times as required.
will be released. The station received before starting seek tuning will be tuned in. Storing programme types One programme type was assigned to each of the preset buttons 1-6 at the factory. If desired, you can also store other available programme types. To do so, make sure that PTY lights up in the display. If necessary, press the PTY button to switch on the function. Select a programme type using buttons << >> and
PTY priority Situation: PTY is switched on and lights up in the display. No station offering the selected programme type can currently be received (with seek tuning or scan). The set will switch back to the previous station. As soon as a programme with such PTY can be received within the broadcasting network, the unit will switch over to the corresponding station for the duration of the programme. Example: German broadcasting network NDR: Station tuned in: NDR3. PTY lights up in the display. Programme type POP selected. Seek tuning is started. No station with PTY-POP can be found. The display shows NO PTY and automatically switches back to NDR3. NDR2 airs a PTY-POP programme. The system will switch to the linked station NDR2 for the duration of the POP programme.
hold down the desired preset button (1-6) until you hear a beep. Now the selected programme type can be recalled by pressing this preset. For this the PTY function must be active. Scanning stations with PTY-SCAN Condition: PTY must appear in the display. Press the SC button. All received stations offering the selected programme types will be scanned. To switch off PTY-SCAN: Press SC once again.
If you wish to listen to a station offering the selected PTY, press / to start seek tuning operation. If the system is unable to find a station offering the selected programme type, the display will show NO PTY and a beep tone

During CD or CDC operation, the set will also switch to the programme offering the selected PTY within the broadcasting network. After the PTY programme the system will remain in the radio mode. Notice: As earlier mentioned, these functions are currently only supported by a limited number of RDS stations.
The abbreviation EON stands for Enhanced Other Networks, meaning the exchange of information within a radio network. Many FM broadcasters offer traffic messages for their service area at regular intervals. All traffic programme stations transmit a special carrier signal alongside their programmes, which is decoded by your car radio. If this signal is identified, TP will appear in the display (Traffic Programme). In addition to these, there are also stations which do not actually transmit traffic programmes themselves, but by using RDSEON they offer the possibility to receive the traffic messages broadcast by another traffic programme station in the same radio network. If you wish to have the priority for traffic announcements activated while listening to one of these stations (e.g. NDR3), TA must appear on the display panel. If a traffic announcement is broadcast, the radio will automatically switch to the linked traffic programme station (in this case, NDR2) for the duration of the message and return to the original programme (NDR3) afterwards.
Traffic announcement priority on/off
If the priority for traffic announcement programmes is activated, TA will light up in the display. To switch the priority on or off: Press the TA button. When pressing TA while a message is being broadcast, this message will be interrupted. The unit will then switch back to the previous condition. The priority for other traffic messages remains active. Please note that several buttons have no function while a traffic announcement is broadcast.

Warning beep

If you leave the reception area of the traffic programme station currently tuned into, you will hear a warning beep after approximately 30 seconds. This alarm tone will also be released when pressing a preset button which has no traffic programme allocated to it.
Receiving traffic programme stations with RDS-EON
Switching the warning beep off a) Tune into another station offering traffic information: Press the rocker switch or press a preset button which has a traffic programme station allocated to it. Alternatively: b) Switch off the priority for traffic announcements: Press TA. TA will disappear from the display.

Adjusting the volume for traffic announcements and the warning beep
This volume was preset at the factory, though you can alter the value using the DSC function (see DSC programming, TA VOL).
Adjusting GEO for traffic messages and the warning beep
You can separately adjust the balance and fader settings for both traffic announcements and the warning beep. For example, it is possible to listen to traffic reports via the front left (right) speaker only. This provides the driver with the important traffic information without bothering the rear passengers too much. To make a setting: During an announcement, adjust the balance and fader settings to suit your personal preferences.
Automatic seek tuning start
(CD and CDC operation) When leaving the reception area of the tuned in traffic programme station while listening to a CD, the system will automatically start searching for a new TA programme. If no such station is found within approximately 30 seconds, CD operation will be stopped and a warning beep will sound. To switch the warning beep off, proceed as described above.
This car stereo is equipped with a CD drive. In addition, it offers you convenient control of a Blaupunkt CD changer CDC-A05 or CDC-F05. These changers are not included in the scope of delivery and can be purchased from your specialised dealer. CD operation

Removing a CD

Press the button for approximately one second (beep). The CD will be ejected. To protect the CD mechanism, do not impair or try to help the automatic insertion and ejection of the disc in any way. If the CD is not removed within approximately 30 seconds, it will be re-inserted automatically.

Selecting a title

After having inserted the CD, the activated CD functions will appear on the display panel. If the TPM indicator is inactive, you can select and play all CD titles. If TPM lights up, you can only select and play the titles programmed with TPM.
Switching to CD operation
Make sure that a disc is inserted, CD IN shows on the display panel. Press SRC to go through the available audio sources: Press as many times until the display briefly shows CD.

Inserting a CD

Switch on the radio. Insert a CD with the label facing up without the use of force. The CD will be transported to its playing position automatically. CD playback will start.
Fast advance, audible (CUE). as long as required. Hold down Fast reverse, audible (REVIEW). as long as required. Hold down

Press the rocker switch as many times until you have reached the desired title. The number displayed beside T indicates the track number of the currently played title.
Up Down Press once to go back to the beginning of the current title.
CD and CDC changer operation (optional)

MIX playback

When the MIX function has been activated, the CD tracks will be played in random order. MIX will then appear in the display. In order to switch the MIX function on or off, press SC/MIX briefly. CDC operation (optional)

Selecting CDs and titles

You can have the CD tracks played in random order. MIX CD The titles of the selected CD will be played at random. The next disc will be selected in numeric order.
Switching to CDC operation
Make sure that at least one CD has been inserted into the magazine. Press SRC to go through the available audio sources: Press as many times until the display briefly shows CDC.
MIX MAG CDC-A 05 / CDC-F 05 All titles of the CD will be played at random. The next disc will then also be selected and played randomly, etc. MIX OFF The Mix function is deactivated. Discs and titles will be selected in numeric order. To alter the setting: Press SC/MIX as many times until the desired function is briefly displayed. If the function is active, MIX will appear in the right display corner.

CD and CDC operation

Storing the display mode
You can store your preferred display mode which will then be active each time the radio is switched on. If required, press AF as many times until the desired setting is displayed. Hold down the AF button until you hear a beep.

TPM Track Program Memory

Use this feature to programme and play your favourite CD titles. Up to 30 CDs can be managed in the CD mode, up to 99 discs in the CDC mode. Storing tracks with TPM Make sure that the TPM function is switched off (TPM not shown on the display panel). If you have not yet stored a track in the TPM, the function will be unavailable. If required, switch TPM on/off by pressing the TPM button. Use / to select a track. The track number will be displayed.
Selecting the display mode
You can select the desired display mode for CD operation: NAME The specified name, for example MADONNA will be displayed.
The CD position in the magazine (disc number) is displayed, for example CD 8. To switch the display mode: Press the AF button during CD playback. The display mode and the corresponding setting or value will briefly show on the display panel, e.g. TIME, 2 : 32. If you have selected NAME without having specified a name for the corresponding disc, CD PLAY will appear in the display. Please read also the chapter Entering CD names.

NUMBER

SCAN will also be terminated by pressing one of the buttons AUD, GEO, DSC, SRC, TPM, , << >> or /.
To stop the Scan function: Press SC/MIX once again briefly. The track currently being scanned is continued to be played.
With CDC operation, a symbol will appear in front of the CD name. Then select the next track with / and store with TPM, as detailed above. You can also store a track at any time during CD playback. For this it is necessary that TPM and SCAN are deactivated. Programme TPM information for other CDs in the same way.
To start the Scan function: Press SC/MIX for approximately one second. The titles will be scanned one after the other in ascending order.
Hold down the TPM button until you hear a beep. Now the track has been stored.
Use this function to scan all of the CD tracks. For CDC operation, the system will scan the titles of all discs.
The elapsed playback time of the title is displayed, for example 2 : 32. In addition for CDC operation:

SCAN operation

CD playback with TPM The TPM function must be switched on (TPM on/off with the TPM button). The tracks stored with TPM will be played in ascending order. Any tracks which were not stored will be skipped over. Clearing TPM information Using the CLR (clear) button, you can clear single tracks, all of the tracks for one CD or the entire Track Programme Memory. For CDC operation, you can also clear the TPM information of either the inserted magazine or all magazines. In order to clear any of this information, TPM must be switched on (TPM lights up in the display). If the TPM contains no data, then NO TPM will appear in the display. CD operation a) Clearing a track from the TPM: Switch on TPM. Select the track with /. Press the CLR button for approximately two seconds until CLR TR appears in the display.
b) Clearing a CD from the TPM: Switch on TPM. Press the CLR button for approximately four seconds until CLR DISC appears in the display.
b) Clearing a CD from the TPM: Switch on TPM. Press the CLR button for approximately eight seconds until CLR CD appears in the display.
Now this disc has been cleared from the TPM. c) Clearing all CDs from the TPM: Switch on TPM. Press the CLR button for approximately eight seconds until CLR TPM appears in the display.
Now this disc has been cleared from the TPM. c) Clearing a magazine from the TPM: Switch on TPM. Press the CLR button for approximately 16 seconds until CLR MAG appears in the display.
Now all of the discs have been cleared from the TPM. CDC operation a) Clearing a track from the TPM: Switch on TPM. Select the track with /. Press the CLR button for approximately two seconds until CLR TR appears in the display.
Now this magazine has been cleared from the TPM. d) Clearing all magazines from the TPM: Switch on TPM. Press the CLR button for approximately 24 seconds until CLR TPM appears in the display.

Now all magazines have been cleared from the TPM.
Now this track has been cleared from the TPM. 50
Now this track has been cleared from the TPM.
In the CD mode you can name up to 30 discs and up to 99 for CDC operation. The specified name (e.g. VIVALDI) will appear in the display if you play the disc in the same operating mode (CD/CDC) that was active when entering the name. Be sure to select the display mode NAME using the AF button. To start the entry: Press the DSC button. CD-NAME or CDC-NAME will be displayed. Press. The first underscore character will flash. Select the first character with the help of the rocker switch /. You have the choice between the capital letters A to Z, special characters and the numbers 0 to 9. Use the rocker switch << >> to move to the next underscore and select a character. You can select up to eight characters for CD and up to seven characters for CDC operation.

Deleting a CD name

Use the DSC feature to delete a CD name. Press DSC. Press / as many times until CD NAME or CDC NAME shows on the display panel.
Press / to select CD UPD or CDC UPD.
Press CLR. The name will disappear. To quit the DSC menu: Press DSC.
Press << >>. After the update has been completed, NEXT CD or NEXT MAG appears in the display. Press for approximately two seconds (in the CD mode on the car stereo, for CDC operation on the changer). The CD or magazine will eject. Insert the next CD or magazine. Proceed as described above for all of the CDs/magazines for which the TPM information and the CD name is to be maintained.

Press the DSC button.

Entering CD names
Once you have completed the name as desired: in order to store it. Press To quit the naming mode, leave the DSC menu by pressing DSC. If you would like to name another CD, insert a new disc in the CD mode or select a new one for CDC operation. You can change any existing name by entering and storing a new one (overwriting).
Clearing TPM information and CD names with DSC-UPDATE
With the help of the DSC update function you can clear CDs from the TPM and delete their names. Use CD UPD or CDC UPD to confirm all of the CDs for which the TPM information is not to be deleted. Insert a CD or magazine with CDs for which the TPM information is to be maintained.

DSC programming

After having updated the last CD or magazine, press TPM for approximately two seconds (beep). To quit the function, press DSC. The system has saved the TPM information for all of the CDs which were inserted. For all other discs, the TPM information and CD names have been deleted. DSC (Direct Software Control) allows you to customise certain programmable, basic settings to suit your personal needs and preferences and then store them. The basic settings for this audio equipment were made at the factory. In the following you can find an overview of these settings, so that you can always reset to these if desired. If you wish to alter any of the programming, press DSC. Use the rocker switch and the button to select and adjust the functions described in the following. The display will show you the adjusted condition. CD/CDC NAME Only available for CD/CDC playback. Use this function to name your CDs. (See Entering CD names). LOUDNESS Loudness - When listening at a low level, the Loudness function creates a more natural sound by boosting the low frequency range. LOUD 1 - Low boost LOUD 6 - Max. boost TA VOL To adjust the traffic announcement and warning beep volume from between 0 to 63. The message will then come through at this volume, if the standard volume is lower. Should the standard volume be higher than the TA VOL level, then the traffic report will be played slightly louder than the standard volume.

/ << >>

Select function Adjust/recall value

SPEECH

In future many RDS radio stations will differentiate between music and speech programmes. You can alter the tone for speech programmes from between SPEECH 0. 4. SPEECH 0: Music/speech off SPEECH 1: Linear reproduction (bass, treble and Loudness set to 0) SPEECH 2-4: Different settings for volume, bass and treble with the Loudness being switched off. Try out which SPEECH setting you like most.
Use this setting to alter the viewing angle to your liking from -1 to 0 to +1. You can adjust the display brightness from between 1 to 16. You can also select different values for day and night. Selecting the night brightness: Switch on the vehicle lights and programme the brightness value. The car radios lighting connector must be hooked up to the vehicles electric system for this to function properly. LEARN KC
the unit has been switched off and the KeyCard removed. To train a second KeyCard. Please read the information in chapter KeyCard theft protection system - Training a second KeyCard. To read out the KeyCard data. The card supplied with the radio is used to display the model name, type number (7 6.) and the serial number. With the extra card it is possible to display the Short Additional Memory (S.A.M.) data entered by your specialised dealer. See chapter Short Additional Memory S.A.M. If you remove the KeyCard during the reading process, READ KC will show on the display panel. The unit continues to play but does not

BRIGHT

Acknowledgement tone for all functions which require a button to be pressed for more than one second. The volume can be adjusted from between 0 to 9. (0 = off).
COLOUR (Variocolour) For gradually matching the radio illumination with the dashboard lighting. green. light orange.. red LED ON Here you can choose between LED ON or LED OFF. With LED ON, the KeyCard tongue will flash for extra anti-theft protection when

READ KC

accept any operations except from being switched off. Re-insert the card. PTY LANG To select the programme type language: DEUTSCH or ENGLISH Use this function to set the scan time for the radio or CD player from between five and 30 seconds. To adjust the seek tuning sensitivity for distant reception. DX 1 - high sensitivity DX 3 - low sensitivity To adjust the seek tuning sensitivity for local reception. LO 1 - high sensitivity LO 3 - low sensitivity The seek tuning sensitivity values can be separately set for AM and FM.

SCANTIME

CD/CDC UPD Use this function to clear TPM information and CD names during CD and CDC operation, in order to have more storage capacity for new discs available. See Clearing TPM information and CD names with DSCUPDATE. AUX This menu item is not available if you have connected a CD changer (A 05 or F 05). The setting made at the factory is AUX OFF. If you have connected an external piece of equipment via AUX, this function must be set to AUX ON. Use this function to select the volume at which the radio is set when it is switched on. Adjust the desired volume level with << >>. When adjusted to VOL 0, the system will come on with the volume selected before switching the radio off.
To quit the DSC programming mode and store the adjustment: Press DSC.
Overview of the DSC factory settings
CD NAME LOUDNESS TA VOL SPEECH BEEP ANGLE BRIGHT COLOUR LED LEARN KC READ KC PTY LANG SCANTIME S - DX S - LO CD UPD AUX VOL FIX green ON ENGLISH 10 sec. OFF 0

VOL FIX

Specifications
Amplifier Output power: 4 x 23 W RMS power acc. to DIN 45324 at 14.4 V 4 x 35 W max. power
Tuner Wavebands: FM : MW : LW : FM sensitivity:
87.MHz kHz kHz 0.9 V at 26 dB signalto-noise ratio
FM frequency response: 30 - Hz CD player Frequency response: 20 - Hz
Subject to modifications! 55
Compatible with DAB box (Digital Audio Broadcasting).
Using the area code to be entered you will be automatically given the address and phone number of the next Blaupunkt service centre. You can also request this information by fax.
Then call the following chargeable phone number: / 56 66.
If you would like to know the address of the next Blaupunkt service centre of your area without having our service list at hand: - Find out your area code.
Address of the next service centre in your vicinity (only for Germany)
Blaupunkt telephone hotline

Appendix

Blaupunkt-Werke GmbH

Bosch Gruppe

1/98 K7/VKD 401 500