Operation Instructions

Verona CR 43

Verona CR 090

3 D061 fr Honda ohne QuickOut

10. 11. 92

Front Panel Description
1 ON/OFF Switch the set on/off by turning the knob. If Cod appears on the display, read the chapter Anit-Theft Coding first. Volume control: By turning the knob SCAN (search operation): During radio reception, the stations are briefly sampled by pressing the knob for approx. one second. Balance: Pull knob and adjust left/right volume by turning the knob. 2 / rocker switch Radio: Automatical station tuning Coding: Read first the Anti-Theft Coding chapter. : Press rocker switch to confirm your code entry. 5 Cassette compartment 6 Track indication - side A or 1 is played - side B or 2 is played (reverse operation) 7 FR button (Fast Rewind) Fast rewind of the tape. Deactivate: press button FF. 8 PROG (Autoreverse) For shifting to the other side of the tape - press both buttons. 9 FF button (Fast Forward) Fast forward of the tape Deactivate: press button FR. : Display for ; Preset buttons 1, 2, 3, 4, 5, 6 Store station - Keep button depressed during radio operation until the station becomes audible again. Recall station - Briefly press the respective button. Coding - Read the Anti-Theft Coding chapter first. Buttons 1 - 4: Use to enter a four-digit code number. Press each of the buttons until the fourdigit code to be found in the car radio passport is represented on the display. < lo rocker switch Use this button to alter the sensitivity of the automatic station seek operation. lo lights up on the display - normal sensitivity lo does not light up - high sensitivity Additional function of the lo rocker switch: Switching from stereo to mono: Press longer than 2 seconds.
DEUTSCH PORTUGUES ESPAGOL SVENSKA NEDERLAND ITALIANO FRANAIS ENGLISH
3 << / >> rocker switch For fine tuning of the stations 4 Ejection of the tape Press button firmly.
frequency waveband preset button storage level stereo seek tuning (sensitivity)

Verona CR 43 - Honda

= ML rocker switch (Medium wave Long wave) Use this rocker switch to select either medium wave (MW) or long wave (LW) frequencies. To switch between these wavebands simply press the rocker switch again. > FMT button (Frequency Modulation) This button is used for shifting between the different FM storage levels I, II, III and T (Travelstore - i.e. storing and calling the six strongest stations of an area). Storing T - Press the FM T button until the seek tuning indication starts to be displayed. Recalling T - Press the FMT button ? until T is indicated on the display. Then briefly press the respective preset button.Balance knob To adjust the volume of the left and right channel ? PS rocker switch (Preset Station Scan) Pressing this button briefly samples all memorized stations of the selected waveband (FM, MW, LW or TS).
@ TREB (Treble) to adjust trebles. A BASS to adjust basses. B FAD (Fader) (front/rear volume): adjust using the lever.

Contents

Important Notes.. 16
What You Should Read By All Means!. 16 Safety Notes... 16 Road Safety.. 16

Radio Section. 18

Selection of the Desired Waveband. 18 Automatic Station Tuning.. 18 Manual Tuning.. 18 Adjusting the Station Seek Sensitivity. 18 Adjusting the local mode sensitivity. 18 Switching between Stereo and Mono. 18 Storing a Station.. 19 Automatically Storing the Strongest Stations.. 19 Activating a Stored Station.. 19 Briefly Sampling a Station. 19 Sampling Memorized Stations. 19

Anti-Theft Coding.. 16

Wrong Code Number Entered. 16 First-time Operation and Restart Following Interruption of Power Supply.. 16 Switching Code System Off.. 17 Switching the Code System Back On If you wish to re-activate the anti-theft code system:.. 17 Optical indication of theft protection. 17

Tape Section.. 20

Inserting the Tape.. 20 Removing the Tape. 20 Fast Forwarding/Rewinding of the Tape 20 Autoreverse.. 20 Care Notes.. 21

Amplifier Section. 17

ON/OFF.. 17 Balance Control. 17 Fader control... 17

Technical Data.. 21

PORTUGUES

ESPAGOL

SVENSKA

Appendix.. 21

NEDERLAND

ITALIANO

FRANAIS

ENGLISH

DEUTSCH

Important Notes

What You Should Read By All Means!
Before starting to use your new car radio, you should carefully read through the safety notes and the information about Anti-Theft Coding.

Anti-Theft Coding

Your radio is protected against theft by an anti-theft coding system. If, once the unit has been encoded, the power is disconnected from the set (e.g. theft, disconnection of the car battery or prior to installation), the set is electronically blocked. It may only be used again after the appropriate code number has been entered (see car radio pass). Hence, a coded set is of no use to a potential thief. our central customer service workshop or to one of our dealers in your vicinity. First-time Operation and Restart Following Interruption of Power Supply Switch on set. Cod will appear in the display :. Briefly press preset button 1 ;, 000 will appear in the display :.

Safety Notes

Road Safety Being the driver of a motor vehicle you should dedicate your full attention to the traffic around you. Therefore always use your car stereo such that you are able to cope with the present traffic situation in any moment. In difficult driving situations you should turn your set off. Please take into account that at a speed of 50 km/h you are almost covering a distance of 14 m per second! When adjusting the volume, always make sure that acoustic signals from the outside can still be heard in order to be able to react to alert signals just as it is required by the present situation.
Enter the code number from the BlauWrong Code Number Entered punkt car radio pass: It should not be possible for thieves to ascerExample: Code number is 1521 tain the code number by trial-and-error. This is why the set is blocked for a certain period - press preset button 1 ; once, of time if an incorrect code number is ente1000 appears in the display :, red. --- would then appear in the display :. - press preset button 2 ; 5 times, This time period is 10 seconds following the 1500 appears in the display :, first three attempts, and is increased to 1 - press preset button 3 ; 2 times, hour following subsequent attempts. 1520 appears in the display :, After 19 unsuccessful attempts OFF will - press preset button 4 ; once, appear in the display : and the set can no 1521 appears in the display :. longer be started. Confirm code number: Press upper part of rocker switch / Note: 2. Keep your car radio pass, which contains the code number, in a safe place in order to avoid Note: unauthorized access to your car radio. If Using preset button 1 the set can only be you lose your radio pass and have forgotten adjusted to 1 or 0. 0 is not indicated in the your code number you will not be able to display. restart the set after the power supply has If you have entered and confirmed an incorbeen interrupted. The only way to make the rect code number, --- will initially appear in set operable again is by sending the radio to the display : and then, after a certain time

Amplifier Section

period, 000. Following this, it is essential that you enter the correct code number. Switching Code System Off If you wish to switch the anti-theft code system off: turn off the radio, simultaneously press, and hold, preset buttons 1 and 4 ; turn the set back on. Cod will then appear in the display :. release the preset buttons 1 and 4 ;. 000 then appears in the display :. Enter the code number that is in the Blaupunkt car radio pass and confirm: See example First-time operation. The anti-theft coding system has now been deactivated. Switching the Code System Back On If you wish to re-activate the anti-theft code system: turn the radio off, simultaneously press, and keep depressed, preset buttons 1 and 4 ;, turn the set back on. Cod briefly appears in the display : and then the set is switched on. The anti-theft code system is now activated. Now whenever the set is turned on, CODE will appear briefly in the display :. Optical indication of theft protection As optical warning of the encoded car radio, 6 flashes when the ignition is the LED switched off, provided the car radio has been connected correspondingly. For this, please see the corresponding installation instructions.

ON/OFF

For switching the set on, turn button 1. Your stereo is now ready for operation. For switching the set off, turn button 1. Volume control turn button 1.
After the adjustment slightly press button.

Fader control

If four loudspeaker are connected, the front/ rear sound impression of the loudspeakers (fader) can also be modified using lever B. Adjusting trebles turn button @. Adjusting basses turn button A. 17
Use button 1 to balance the sound impression of the right and left channel speaker. Pull (lock in) button and turn.

Balance Control

Radio Section
Selection of the Desired Waveband
This radio allows you to choose between the FM, MW and LW wavebands. FM Selection Briefly press the FMT rocker switch >. FM is displayed in the display (for Frequency Modulation). MW or LW Selection Briefly press the ML rocker switch =. An M (for MW), or an L (for LW) will then appear in the display. If you wish to switch between MW and LW: press the ML rocker switch = again. The following instructions apply for all wavebands, as long as not otherwise indicated. Tuning of Previous Station Press rocker switch / 2 down. The radio will automatically seek the previous station. If the rocker switch / 2 is held down/up, the seek operation continues to be carried out quickly in the corresponding direction.

Adjusting the local mode sensitivity
In regions with extremely high station density, e.g. in Italy, the set allows you to switch over the station seek sensitivity for the ocal mode from High (adjusted ex works) to Low. Low means that station seek tuning only captures the most powerful stations. For modifying the local mode: press button lo < longer than 8 secs. The display : shows L for Low. By pressing button lo < again longer than 8 secs., the set switches back to High (display : H). When switching off the unit or when removing the set with the QuickOut handle the set remains in the last activated mode.

Manual Tuning

It is also possible to tune in stations by hand with this radio: Press rocker switch <</>> 3 to the left or to the right. The frequency band is scanned in small steps.
Adjusting the Station Seek Sensitivity
You may also modify the sensitivity of the automatic station seek operation. For this: press lo rocker switch <. If lo is indicated, only stations with good reception conditions are captured (lower sensitivity). If lo is not indicated, stations with a weaker reception are also captured (higher sensitivity).

Automatic Station Tuning

Tuning of Subsequent Station Press rocker switch / 2 up. The radio will automatically seek the next station.
Switching between Stereo and Mono
If you wish to switch between stereo and mono: keep the lo button < pressed for longer than 2 seconds. The stereo symbol will appear in the display : if the stereo mode is activated. The stereo function is activated automatically when you turn your set on. The set will automatically switch to mono if reception is poor.

Storing a Station

Automatically Storing the Strongest Stations You can store one MW and LW station and 4
FM stations on each of the preset buttons ;. The display will show you the selected waveband (FM, MW or LW) and preset button. On FM, the display will also give you the chosen storage level (I, II, III or T). If you wish to change from one storage level to another: press the FMT button >. If you wish to store a station: (for FM only) select the storage level. To achieve this, press the FMT button > until I,II,III or T appears in the display :. tune in the station (see chapter Station Tuning). press the desired preset button ; until the radio resumes play (approx. 2 seconds). The display : indicates which preset button has been pressed. The station has now been stored. Note: When tuning in an already stored station, the display : will show the corresponding preset button for approx. five seconds and the respective storage level. (Travelstore) With Travelstore, you have the opportunity to automatically store the six most powerful FM stations of your local reception area and have them sorted according to their frequencies. This feature is of special use while travelling. Press the FMT rocker switch > for at least two seconds. The set searches for the next FM stations and sorts them on the T (Travelstore) storage level. Once the process is finished, the car radio tunes in to the first station. If required, it is also possible to manually store a station on the Travelstore level. If less than five stations can be received, the free buttons are represented by dashes for a short period of time.

Briefly Sampling a Station
(Radio Scan) Starting with the currently tuned in station, you can have the following ones briefly sampled for approx. eight seconds each. Press the knob 1 for approx. 1 sec. If the following station is found, it is reproduced for approximately eight seconds.The stations frequency starts blinking on display :; if it has already been memorized, the corresponding preset button and the storage level indicator starts blinking on display :. Subsequently, the set starts searching for the next station. For selecting a sampled station: Press the knob 1 once again. The Scan function is off. After the search operation has been concluded, and no station has been chosen, the radio starts playing the station from which Station Scan was started before.
Activating a Stored Station
If required, the memorized stations can be activated at a keystroke. Choose the storage level. For this, press FMT > until the display : shows I, II or III, or T. Briefly press the required preset button ;.
Sampling Memorized Stations
All memorized stations of a waveband can be briefly sampled. Press the PS rocker switch ?. One after another, the car radio will then start introducing all memorized stations of the selected waveband. 19

ESPAGOL PORTUGUES

Tape Section
The set either samples the stations of storage levels I-III or of the Travelstore level T. This depends on the current switching status. If a preset button has no station allocated, this button is skipped. To terminate this function: Press the PS rocker switch ? once again. The station currently sampled is maintained.

Inserting the Tape

If you wish to play a cassette tape: switch the set on gently insert the cassette with side 1 upwards. The tape will then be played in the direction it was last played. Track indication 6 indicates which side is played. - side A or 1 is played. - side B or 2 is played (reverse operation).
Fast Rewind Press the FR (Fast Rewind) button 7. Once the tape has been completely rewound, the set begins playing the tape. Stopping the Fast Rewind Operation Press the FF button 9.

Autoreverse

If, while a tape is playing, you wish to switch to the other side of that tape: press the FF and FR buttons simultaneously. At the end of the tape the set will automatically switch to the other side of the tape. Note: When playing stiff tapes it is also possible to manually switch to the other side of the tape. If this is the case, check the tape wound up to that point; fast forwarding or rewinding often helps in such cases.

Removing the Tape

If you wish to remove the tape: button 4. The tape is press the then ejected.
Fast Forwarding/Rewinding of the Tape
Fast Forward Press the FF (Fast Forward) button 9. At the end of the tape the set will switch to the other side and resume playing the tape. Stopping the Fast Forward Operation Press the FR button 7.

Appendix

Care Notes
We recommend C-60 and C-90 type tapes for use in any automobile tape player; to protect your tapes, store them in a cool place away from dirt, dust, or excessive temperatures above 50 Celsius. In order to ensure smooth tape operation, cold tapes should be allowed to heat up a bit before they are played. If dust collects on the audio head or the rubber roller, problems related to rough tape operation or poor sound quality may occur after approx. 100 hours of operation. For normal contamination, use a headcleaning cassette to remove the dust; for more intensive contamination, use a cottonwool tip soaked with alcohol. Never use hard tools!

Technical Data

Amplifier Output power: 4 x 4.5 W watts RMS acc. to DIN 45324/3.0.9 V at 26 dB signal-to-noise ratio 35 - Hz (-3 dB)
FM: Sensitivity: Frequency response: Tape Section: Frequency response:

31.5 - Hz (-3 dB)

Modifications reserved! 21

Bosch Telecom

1/93 MC/VKD-Hi 3 D061 PM

Blaupunkt-Werke GmbH