Bose 802 Series II Loudspeaker

General Description

The Bose 802 Series II sound components provide a fully modular system designed for high quality reinforcement of voice and music. Bose 802 Series II loudspeakers work with the 802C Series II systems controller for active equalization of the system. The 802 Series II loudspeaker is preferred for applications requiring a rugged, portable enclosure, but can be used in permanent indoor sound system installations. The 802C Series II systems controller assures smooth, accurate spectral response across the entire operating range of the 802 Series II loudspeaker. Sharp subsonic and ultrasonic band-limiting filters reduce power waste, stage noise, high-frequency instability, and interference. The systems controller also provides two independent signal channels.
Modular components for system design flexibility High linear excursion and power output Electronic systems controller

Technical Information

Frequency range 55Hz 16kHz Active equalization (with 802C Series II systems controller) Required Nominal impedance 8 Maximum acoustic output 114dB-SPL average, 123dB-SPL peak Power handling capacity 240W continuous pink noise, 55Hz 16kHz Recommended amplifier power 240W minimum, 480W maximum Sensitivity Full-range, 91dB-SPL (1W, 1m) Horizontal beamwidth 120 Vertical beamwidth 100 Enclosure construction Mica-reinforced polyethylene copolymer structural foam Fusing Built-in 4-ampere quick-acting fuse (replaceable) Insert locations Four M8 (8 mm) Connectors Two (2) parallel-wired 14" (6.3 mm) phone jacks and two (2) parallel-wired male XLR connectors Dimensions 13" (H) x 2012" (W) x 1212" (D) (33 x 52 x 32 cm) Weight 31 lb (14 kg)

Component Description

Each 802 Series II loudspeaker uses eight 412" full-range drivers mounted in symmetric vertical pairs on a faceted Articulated Array baffle assembly. The drivers feature low-impedance, edge-wound aluminum voice coils, 12-ounce Ferrite V ceramic magnets, and molded polyester frames. Their advanced cone and motor system give them high linear excursion capability and power output.
Tuned reactive air columns reduce distortion by controlling the cone excursion required to reproduce deep bass frequencies. A built-in directivity control circuit maintains the vertical dispersion pattern through the high-frequency range. It also protects the drivers from high-frequency overload. The 802C Series II systems controller is a single-rack sized device. It is capable of providing crossover functions, active electronic equalization, and dual channel signal processing for both the 802 Series II loudspeakers and the 502 B or 502BP Acoustimass enclosure. It features -10/+4dB-V input sensitivity switches, all-balanced inputs and outputs, -18/+3dB bass level control, and a bass mono sum switch. It also provides automatic output muting on turn-off, and a secure rear-panel operating mode switch.
REFER TO YOUR INSTRUCTION MANUAL FOR PROPER INSTALLATION AND OPERATING PROCEDURES. INCORRECT WIRING MAY RESULT IN DAMAGE AND/OR POOR PERFORMANCE. CAUTION AVIS
RISK OF ELECTRICAL SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR

MODE SWITCH GUIDE

POSITION OPERATING MODE 2-WAY WITH LOW FREQUENCY OPTION (NOT USED) STANDARD 2-WAY (WITH 502B) VOICE ONLY/FULL RANGE (WITH 502A)
TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
MODE INPUT LEVEL 10 +4 NC +BA 1 FR PROTECTED BY U.S. PATENT 3,038,964 INPUT LEVEL OPT 4

HIGH FREQ OUTPUT

PIN 1 GRN PIN 2 + PIN 3

LOW FREQ LEVEL. 0.

LOW FREQ OUTPUT

OUTPUT MODE SUM NORM

230V~AC 50/60Hz 12W

CH 1/SUM

TV Rheinland

geprdfte Sicherheit

the loudspeaker shall be 240 Watts continuous pink noise, band limited from 50Hz to 16kHz.

INPUT B

INPUT A

BRIDGE

MADE IN
CAUTION In order to grant a secure operation do not mount the amplifier in a fully closed housing. To preven electric shock, do not remove cover. Disconnect power line in case of servicing. ACHTUNG: Um sichere Funktion zu gewhrielsten, Gert nicht in vollstndig geshlossenes Gehuse einbauen. Abdeckung whrend des Betriebes nicht entfernen. Bor Offnen des Gertes Netzstecker ziehen. Bose Corporation, Framingham 01701, Mass, U.S.A.

Serial No.:

Made in Germany

Figure 1

Beamwidth vs Frequency (Bose 802-II)
The loudspeaker shall be provided with a ducted vent system, tuned at 55Hz. The input connectors of the 802 Series II loudspeaker shall consist of two (2) parallel-wired 14 inch (6.3 mm) phone jacks and two parallel-wired male XLR connectors. The loudspeaker enclosure of the 802 Series II loudspeaker shall be composed of mica-reinforced polyethylene copolymer structural foam. Outer dimensions of the 802 Series II loudspeaker shall be 13" (H) x 2012" (W) x 1212" (D) (33 x 52 x 32 cm); its weight shall be 31 lb (14 kg). The loudspeaker shall be the Bose 802 Series II loudspeaker system. The loudspeaker system shall be supplied with a separate systems controller, to be connected before the input(s) of the system power amplifier(s). The fixed, 2-channel systems controller shall provide active electronic equalization and crossover functions. It shall include an operating mode switch, input sensitivity switch, low-frequency output level control, and mono sum switch. The systems controller shall use screwtype terminal strips for balanced input and output wiring connections. Outer dimensions of the systems controller shall be 134" (H) x 19.0" (W) x 8.0" (D) (4 x 48 x 20 cm). It shall fit in the single space of a standard 19" equipment rack for mounting. Its weight shall be 5.5 lb (2.5 kg). The electronic controller shall be the Bose 802C Series II systems controller.

Systems Controller Technical Information
Audio channels Two Operating modes Full-range, bi-amp, option (w/option card) Rear panel connectors Balanced in-out x 2 (XLR) Balanced high-frequency output x 2 (XLR) Balanced low-frequency output x 2 (XLR) Crossover 140Hz with 502B bass enclosure 125Hz with OC-1 option card Rear panel controls Mode switch Input sensitivity switch x 2 (-10dB-V, +4dB-V) Bass level control (range -18dB, +3dB) Bass mono switch (norm/sum) Electrical specifications Channel separation: >60dB @ 1kHz Input impedance: 2.4k nominal Output impedance: 600 nominal Output level: 8.0V RMS max. into 600 Mechanical specifications Dimensions: 134" (H) x 19.0" (W) x 8.0" (D) (4 x 48 x 20 cm) Weight: 5.5 lb (2.5 kg)
Figure 2 For information on the 502 B and 502BP Acoustimass enclosure, refer to the technical data sheet for those products.
An optional plug-in card is available for the 802 C Series II systems controller. This allows the 802 Series II sound system to include the Bose Acoustic Wave Cannon System Series II loudspeaker.
For information on the Acoustic Wave Cannon System II loudspeaker, refer to the technical data sheet for that product.

System Configurations

The Bose 802 Series II system provides a flexible, building-block approach to meet the sound reinforcement requirements in many applications. Figure 1 shows a basic 802 system configuration. It consists of two 802 Series II loudspeakers and one 802C Series II systems controller. This system provides 117dB-SPL @ 1 m average acoustic output. Figure 2 provides a graph of the basic systems vertical and horizontal beamwidth. Figure 3a and b show the front and back of the 802C Series II systems controller.
Safety and EMC Compliance
Safety: UL 813 CSA C22.1 #1 IEC65/EN60065 EMC: EN55013 EN55020
Engineers and Architects Specifications
The loudspeaker shall be a multiple driver, full-range system with matched active equalization as follows: The transducer complement shall consist of eight (8) full-range drivers of 11.4 cm diameter, mounted symmetrically in vertical pairs on a faceted, removable baffle assembly. Each driver shall have a rated impedance of 1 and shall be wired in series, resulting in a composite nominal impedance of 8. The loudspeaker system sensitivity shall be 99dB-SPL in the 300Hz 3kHz range and 92dB-SPL in the 50Hz 16kHz range with both measurements referenced to a 1 Watt (2.83V) pink noise input at 1 meter. The nominal horizontal beamwidth shall be 120 degrees, and the nominal vertical beamwidth shall be 100 degrees. The power handling capacity of

Product CE is compliant for EMC and Safety.

Warranty Information

The Bose 802 Series II loudspeaker is covered by a 5-year, transferable limited warranty. The Bose 802C Series II systems controller is covered by a 2-year, transferable limited warranty.

Figure 3a

Figure 3b
1996 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA JN94532 PN177918 Rev.05 AM177918 Rev.05 PC010248

Q & A

PANARAY 802-III Loudspeaker
What is new about the PANARAY 802-III loudspeaker?
The PANARAY 802-III loudspeaker has been improved in the following ways: The cabinet and grille have been redesigned to update the look of the speaker. The product has met or exceeded strict environmental testing for long life outdoors. We test for durability in heat, cold, salt fog, humidity, and sand and dust conditions. The fuse has been removed and the speaker now has an internal protection circuit that trips and resets should the input to the speaker exceed recommended levels. The drivers are new. The environmental durability is built-in. The soft parts of the driver are impregnated with Kevlar and other resins for moisture resistance. The hard parts are coated for resistance to damage from harsh weather. The rear connectors are now two parallel-wired Neutrik NL4 Speakon receptacles. There is now a full line of brackets for wall mounting and flying the 802-III speaker. There are new equalizer cards to match the performance of the Series III speaker. There is a new PANARAY System Digital Controller loaded with simple-to-use presets for the 802-III in mono or stereo, singles or pairs and crossed over with Bose bass loudspeakers.
What is unchanged about the PANARAY 802-III loudspeaker?
The PANARAY 802-III loudspeaker still provides natural sound and high output from a compact, lightweight enclosure. The 802-III speaker uses innovative design features that have characterized its performance since the first 802 speakers were introduced. Here is a list of these innovations: Articulated Array speaker configuration 4.5-inch drivers Rugged, durable carrying case that doubles as a monitor stand Ergonomic handle for easy carrying
Information subject to change without notice
When was the first 802 loudspeaker made?
In 1972, Bose entered the professional market by offering the 800 loudspeaker system designed exclusively for the demanding, discriminating tastes of the professional musician. The 800 product used the technologies developed for the 901 speaker and created a product for professional use. In 1978, Bose redesigned the 800 speaker to create the 802 Series I loudspeaker. This product recreated the 800 acoustic package in a light and high-impact-resistant case with a unique cover/carrying handle feature. The 802 also improved on the 800 array design and power-handling characteristics of the full-range drivers. The 802 product set the standard for professional loudspeakers for years to come.
What are the benefits of the 4.5-inch drivers?
The 4.5-inch, full-range drivers provide a more consistent sound field than conventional speakers that rely on woofers, tweeters and crossovers.Traditional speakers need to electronically cross their drivers in one or two bands. These crossovers usually cause a dip or a spike in the frequency response of the speaker, adding an unnatural element to the speaker performance. Additionally, these crossovers often occur in the frequency range of voice reproduction, where human ears are most sensitive to discrepancies in sound fidelity. The patented 4.5-inch driver design also dissipates heat more easily than conventional transducers for greater power handling. Cooler drivers have a longer life with greater reliability. Eight full-range drivers in a single 802 enclosure can handle 240-watt continuous or 480-watt peak power. Bose has engineered exceptional durability and reliability into this driver, and is continuously improving on its strength and acoustic clarity.
What does it mean that this can be installed outdoors?
The environmental durability is built-in. The soft parts of the driver are impregnated with Kevlar and other resins for moisture resistance. The hard parts are coated for resistance to damage from harsh weather. It has met or exceeded strict environmental testing for long life. We test for durability in extreme heat, cold, salt fog, humidity, and sand and dust conditions.

What is different about the grille?
The styling on the grille is new and echoes the famous ports of the 802 Series I and II. The grille is now metal for greater environmental durability.
Why did you get rid of the ports?
The ports are not removed, only recessed into the housing. They have the same acoustic performance as the 802-II ports. They were recessed as part of the cosmetic update of the speaker.
What is the purpose of the ring around the grille?
This is called the trim ring. It is a part of the cosmetic update of the speaker. It is very durable and has been shown to withstand active portable use. OF 5
What is an Articulated Array?
Bose discovered that by using an array of full-range drivers and a ported enclosure they could create full-range sound reproduction with greater clarity and smoothness. The Articulated Array speaker baffle configures the eight full-range drivers to provide consistent and wide horizontal and vertical dispersion over all bandwidths.
How many can I stack in a column?
The 802-III can be used as a single, a stacked pair, or stacked vertically as a column. Depending on the application, any number can be stacked to achieve the output desired.
Does the 802-III loudspeaker work with the previous 802C controller?
The 802C is discontinued. We do not recommend use of the 802-III with the previous revision 802C as this sound will not be optimal.The current PANARAY System Digital Controller is programmed for the 802 Series I, II and III and has easily selectable settings for mono, stereo, and two-way use of the speaker with Bose bass loudspeakers.
Can I mix 802-II and 802-III loudspeakers in the same stack or system?
The sound may not be optimal if series II and III speakers are mixed in a stack. If speakers are used in mono and separated by distance, the acoustic difference between the Series II and III will most likely not be noticed.
What are the connectors on the back?
Two Neutrik NL4 Speakon connectors, wired in parallel.
Where do I cross it over with the MB4? 502B? Model 1B?
We recommend that you crossover the 802-III speaker at 160 Hz when using it with a Bose bass loudspeaker. The PANARAY System Digital Controller contains easy-to-use presets for each of these scenarios.
What brackets are available for the 802-III loudspeaker?
The 802-III brackets are optional, come in black and are weather resistant. WBP-SB8-802 SB82-802 Bipivot wall mount bracket Single fly bracket Stacked pair fly bracket

Are the brackets environmental?
The steel materials in the brackets are a pre-coated G90 (hot dipped galvanized) material. The products are then powder-coated. We do not recommend these brackets for high salt fog environments, such as cruise ships, but standard outdoor installation is acceptable and the brackets are adequately protected. Thin surface scratches can be tolerated provided theyre not too wide or deep. The precoating will provide adequate galvanic protection across thin scratches.
Is the PANARAY 802-III loudspeaker actively equalized?
Yes, the 802-III speaker requires active equalization. Active equalization ensures balanced low, mid and high frequencies in the loudspeaker. In addition, it provides high- and low-band pass filtering.
How do I get the proper equalization for the PANARAY 802-III ?
There are two options for 802-III active equalization. There is an 802-III equalizer card available for use with the Bose M2150, 1600 VI and 1800 VI amplifier input cards. The PANARAY System Digital Controller provides easy, push-button presets for all Bose professional loudspeakers. The PANARAY controller contains 180 presets for mono and stereo operation, as well as three presets for bass arrays. As a bonus, programmable delay, limiting and routing are available in this 2 x 4 controller.
What is happening to the 802C controller?
The 802C controller has been discontinued and is replaced with the PANARAY System Digital Controller that has all the functions of the 802C controller plus programmable delay, limiting and routing. The PANARAY System Digital Controller contains 180 presets for use with all Bose professional loudspeakers.
What amplifier should I use to drive the 802-III loudspeaker
We recommend that one channel of the Bose 1800 VI amplifier drive each 802-III loudspeaker.
What are the design rules?
The design rules for the 802-III are the same as the series II loudspeaker.
What colors does the PANARAY 802-III loudspeaker come in?

The 802-III comes in black.
What is the frequency response of the PANARAY 802-III loudspeaker?
55 Hz to 16 kHz 3 dB (same as 802-II)
What is the maximum power handling of the PANARAY 802-III loudspeaker?
240-watts continuous (same as 802-II)
What are the dimensions of the PANARAY 802-III loudspeaker?
33 cm H x 52 cm W x 32 cm D (same as 802 II)
Is the PANARAY 802-III loudspeaker paintable?
What the maximum SPL of the PANARAY 802-III loudspeaker?
114 dB SPL @ 1 m, pink noise 116 dB SPL @ 1 m, IEC noise
How much does one PANARAY 802-III loudspeaker weigh?

14 kg or 31 lbs

What is the warranty on the PANARAY 802-III loudspeaker?
As with all Bose professional loudspeakers, the 802-III loudspeaker has a five-year limited transferable warranty.