LIFESTYLE 18 Series II LIFESTYLE 28 Series II DVD Home Entertainment Systems

Operating Guide

Safety Information Please read this owners guide

English

Please take the time to follow this guide carefully. It will help you set up and operate your system properly and enjoy all of its advanced features. Save both the Installation Guide and the Operation Guide for future reference. WARNING: To reduce the risk of fire or electric shock, do not expose the system to rain or moisture. WARNING: This apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be placed on the apparatus. As with any electronic products, use care not to spill liquids in any part of the system. Liquids can cause a failure and/or a fire hazard. The CAUTION marks shown here are located on the bottom of your LIFESTYLE DVD home entertainment system media center and on the rear panel of the Acoustimass module:
The lightning flash with arrowhead symbol, within an equilateral triangle, alerts the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle alerts the user to the presence of important operating and maintenance instructions in this owners guide. CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The compact disc player should not be adjusted or repaired by anyone except properly qualified service personnel. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus. Class 1 laser product
The DVD player contained within the media center is classified as a CLASS 1 LASER PRODUCT according to EN 60825-1:1994 + A11. The CLASS 1 LASER PRODUCT label is located on the bottom of the media center.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER LASER LASER LASER PRODUCT PRODUKT LAITE APPARAT

Class B emissions limits

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Batteries

Batteries

Please dispose of used batteries properly, following any local regulations. Do not incinerate.
Additional safety information
See the additional instructions on the Important Safety Instructions sheet enclosed in the shipping carton.
2004 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior written permission. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories. All rights reserved. This product contains one or more programs protected under international and U.S. copyright laws as unpublished works. They are confidential and proprietary to Dolby Laboratories. Their reproduction or disclosure, in whole or in part, or the production of derivative works therefrom without the express permission of Dolby Laboratories is prohibited. Copyright 1992-1996 by Dolby Laboratories, Inc. All rights reserved. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. MPEG Layer-3 audio compression technology licensed by Fraunhofer IIS and THOMSON multimedia.

Contents Where to find.

Introduction. Welcome. Types of discs you can play. Check for region number compatibility. Glossary of audio terms. Capabilities and Controls. The remote control. If the remote does not work as you expect. The media center. Activating component or progressive scan connections. System Operation. Making it all work together smoothly. To turn on other components. To watch video. To adjust what you see or hear. Loading and playing a DVD. Control options. Using parental controls. Loading and playing a CD. Control options. Using the radio. Changing stations. Setting a station preset. Using the headphone jack. Using the sleep timer. To set the timer. Controlling External Sources. Using your LIFESTYLE remote with other components. For TV control. For cable/satellite control. For VCR (or DVR) control. For AUX control. Designating one video tuner. Changing Source Settings. Making adjustments to a particular source. How to see your options. How to change the settings. Tuner setting options (FM or AM radio). CD setting options. DVD setting options. TV setting options (for VCR, CBL-SAT, and Aux). 28

Espaol Franais

This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is recommended that the user switch the connection to the standard definition output. If there are questions regarding our TV set compatibility with this model 525p DVD player, please contact our customer service center. This product incorporates copyright protected technology and other intellectual property rights owned by Cirrus Logic, Inc. and subject to the copyright protection of the U.S. as well as other licensing restrictions and protections. Use of this copyright protected technology is limited solely to use with the Cirrus Logic integrated circuits incorporated in this product. Reverse engineering or disassembly is prohibited. Designed with UEI Technology Under License from Universal Electronics Inc. UEI 2000-2002.

Contents

Using System Menus. Making system adjustments. How to see the System menu. How to make changes. Audio options. Video options. Media center options. Remote control opitons. DVD lock options. Applying parental control. Reference. Remote control maintenance. Replacing the remote control batteries. Changing house code settings. Setting up a second room with sound. Bose link: the key to assured compatibility. Taking care of your LIFESTYLE system. Limited warranty. Troubleshooting. Contacting customer service. Accessories. Technical information. 43 43

Introduction Welcome

Thank you for purchasing a Bose LIFESTYLE DVD home entertainment system. Through proprietary Bose technologies and innovative LIFESTYLE systems design, this elegant and easy-to-use system delivers superior performance for both music and video programming.

Capabilities and Controls The remote control
The advanced radio-frequency remote control provided with the LIFESTYLE system works from almost anywhere inside your home. Simply press any button. There is no need to aim the remote at the media center.

Power and mute

Turns the system on and off. Selects the source last used. Mutes the volume for all connected speakers (main and in other rooms). Mutes or unmutes the volume in the current room.
Source and input selection
Turns the system on and selects the built-in disc player as source. Turns the system on and selects the built-in FM/AM radio tuner set to the station last selected. Switches between FM and AM when the radio is on. Turns the system on and selects an AUX source connected to the media center. Turns the system on and selects the TV connected to the media center as source. When the remote has been set to do so*, turns the TV on and off. When the remote has been set to do so, scrolls the TV inputs to select one. The input that connects to the media center is one choice. Turns the system on and selects a cable box or satellite receiver connected to the media center. When the remote has been set to do so*, turns your cable or satellite box on and off. Turns your system on and selects the VCR connected to the media center as the sound source. When the remote has been set to do so*, turns your VCR on and off.
*You can choose to set the LIFESTYLE remote to control your TV, cable or satellite box, or VCR so it will turn those devices on or off. To do that, refer to Using your LIFESTYLE remote with other components on page 18. Until then, however, simply turn on the TV or component using its power button or remote control. 7
Capabilities and Controls
Menu and program selection English
Enters or exits the Settings menu for the current source. Enters or exits the System menu. Enters or exits the menu of the DVD disc that is currently loaded. Enters the main menu of a cable or satellite box. Displays an electronic TV listings guide (if the TV, cable, or satellite provides that option). Exits the Settings and System menus. Exits electronic TV listings.
Tune the FM/AM radio up or down to the next frequency. Selects the previous or next item in a menu list.
Enters submenus or confirms the selection of a menu item.
Move up, down, left, or right in a menu or screen.
Seek backward or forward to the next strong radio station. Skip to the next or previous TV channel, CD track, DVD chapter, or radio preset.
Raise or lower the volume of the current source. Pressing + unmutes the current source in the current room only, if it was muted. Pressing lowers the volume. Select a DVD chapter, CD track, radio station preset, or TV channel that corresponds to the numbers pressed. Use to make changes to some items in the System and Settings menus, when numbers apply.
Skips to the previous TV channel.* Displays or exits the cable or satellite information window, if available. Pressing and holding this button (until the change is apparent), removes or restores auido track information on the media center display.

Play options

Note: All of the buttons shown below, except Shuffle and Repeat, can be used with your VCR or DVR after the remote has been set to control it. Stops the disc player. Note: For DVDs and VCDs only, the system remembers the point where the disc was stopped. Pressing again clears that memory. Pauses the disc player. Starts the disc player. Skip back or forward to the start of a track or chapter. Or, when pressed and held, scans back or forward through the current CD or MP3 disc, or adjusts the speed of the scan. Plays CD tracks in random order. Press Shuffle again to cancel this mode. Repeats a whole CD or track, DVD chapter, or DVD title. Press Repeat again to cancel the repeat mode.
If the remote does not work as you expect
If your system does not respond when you press a button on the remote, it could be time to change batteries. For information on the type of batteries to use and how to change them, refer to Troubleshooting on page 41. In some buildings, you may experience dead spots where the remote control will not operate effectively. If this happens, move the remote a foot or two and try again. Also make sure the cord that connects the power supply to the media center (and contains the remote antenna) is stretched to its full length. If these efforts do not work, move the media center a few feet to a location where it provides a better response. If the batteries are fine and the suggestions concerning dead spots above do not work, you may need an antenna extender. To contact Bose customer service to request one, refer to the address list included with the system.
Capabilities and Controls The media center
The CD/DVD tray and system controls are located under the front panel door of the media center. To the right of that is the display window (Figure 1). An IR signal emitter, located under the CD/DVD tray, enables you to control other components using the LIFESTYLE remote. Avoid blocking the emitter, so its signal will have a clear path to other components or reflective surfaces in the room. Figure 1
Front view of the media center Front panel door lifts up Display window Headphone jack

Disc tray

IR emitter

Controls

The nine control buttons work as described below.

On/Off

On/Off Source Volume
Turns the system on or off in the main room only. Selects the source last used when it turns the system on.

All Off

Turns off the system and all connected speakers (in all rooms).

General System Operation

To adjust what you see or hear
For changes to a particular source: Press the Settings button on the LIFESTYLE remote control. To see your choices on the TV, be sure you have the TV on and its Video input is set for the media center. For details on the changes you can make, refer to Making adjustments to a particular source on page 24. For changes to system operation: Press the System button on the LIFESTYLE remote control. Be sure you have the TV on and its Video input is set for the media center. For details on the changes you can make, refer to Making system adjustments on page 29.
Loading and playing a DVD
The symbols below represent buttons on the LIFESTYLE remote control unless otherwise indicated. 1. 2. 3. 4. 5. 6. Turn on your television. Press to select the DVD player. If the system is off, this will also turn it on.
Lift up the media center front door and press Insert a DVD into the tray (label side up). Press Press

on its control panel.

again to close the disc tray. to begin play.
You may need to press the play button more than once. Most DVD videos present on-screen selections before the movie begins. Note: Not all DVDs offer the same features. For example, you can choose to display subtitles while watching a movie only if that disc provides subtitle information.

Control options English

If you want to: Pause a DVD movie Resume play Stop a DVD movie Do this: Press Press. again or.
Press once. Then press to continue playing from where the movie stopped. Or, press twice to stop and reset. Then press to restart at the beginning of the DVD. Press up.

Skip to the next chapter

Skip to the previous chapter

down twice.

Repeat a chapter
while the chapter you want to repeat plays.
Search backward or forward Press and hold
Note: For information on the quick adjustments you can make to DVD settings refer to DVD setting options on page 27. Instructions on how to enter the menu to make those changes are available in How to see your options on page 24.

Using parental controls

The parental control feature of your LIFESTYLE system allows you to restrict access to DVD movies with ratings you find inappropriate for members of your family. Before you can use this feature, you choose a password and a level of restriction in the System menu. To learn more about parental controls refer to on page 34. Note: Refer to Troubleshooting if you have trouble with a password.

Controlling External Sources Using your LIFESTYLE remote with other components
You can control most brands of external components, such as TVs, VCRs, and cable/satellite boxes, using your LIFESTYLE remote control. You can also designate one of these components as the video tuner (channel selector) for all, to further simplify operation. Your LIFESTYLE system includes an infrared (IR) emitter that sends out signals from the front of the music center to any component that your LIFESTYLE remote is set to control. This allows you to turn on other sources in the room and make basic selections from them, whether they are connected to the media center or to the TV. Note: If a component is located where it cannot receive these IR signals, you can use the supplied IR emitter cable with that component. For tips on getting the IR signals where they need to go, or using the optional emitter, see Connecting the optional IR emitter cable in your Installation Guide.

For TV control

Note: For general guidelines on using the LIFESTYLE System menu, refer to Using System Menus on page 29. Use the TV remote to turn on the TV. Be sure to select the Video input on the TV for the media center. Then, using the LIFESTYLE remote control: 1. 2. 3. 4. Figure 4
Preview of Remote features in the System menu
Press the TV button to select the TV source. Press the System button. The System menu will appear on the TV screen (Figure 4). Move across the categories to Remote Control to preview these menu options. Press the Down arrow or Enter to move into that menu.
Remote Control IR Control: TV Tuner: TV Brand: TV Device Code: VCR Brand:

Select your TV brand.

navigate

select

Controlling External Sources
5. Identify the TV brand: From the Remote Control options in the System menu, select TV Brand (Figure 5). Move right into the list of brands and up or down to locate the brand for your TV. Press Enter to select that brand. Figure 5

TV brand selection

Remote Control IR Control: TV Tuner: TV Brand: TV Device Code: VCR Brand: Philex Philharmonic Philips Phoenix Phonola
Choose the device code: In the menu options on the left, select TV Device Code. Move right to select the first code. Press the TV On/Off button on your LIFESTYLE remote. Press that button again. If the TV turns off and on again, you have chosen the right code. If the TV does not turn off, select another code, and press the TV On/Off button two more times.* When you have chosen the right code, press the Enter button. To have the TV come on automatically, whenever you press a video source button, follow Step 7 on page 20. To skip this step, press System or Exit to leave the System menu.

*Some manufacturers use a number of similar device codes. After selecting one, you may find you can turn your TV on and off, but are unable to change channels or select Play or Pause. In that case, select a different device code that provides more control. 19
7. Set the TV to turn on automatically*, as needed: Move up to the System menu categories and over to Video (Figure 6). From the Video options, select TV Power. Move right into the list of choices and up or down to select one of the two below: -Automatic (for TV models that do not use a European style SCART connector) -Euro Connector (for TV models that use a SCART connector) Press the Enter button. Figure 6

Changing the TV Power

Video TV Power: TV Power Status: TV Aspect Ratio: Widescreen DVDs: Video Connector: Video Black Level: Manual TV Not Detected --Component Normal
The Media Center can turn your TV on automatically whenever you select a video source.

navigate select

*For the Automatic feature to work effectively with North American TV models, the optional TV sensor must be installed and positioned to detect if the TV is on or off. In Europe, a SCART connector serves this purpose. If you do not use a SCART connector, or the TV sensor is not positioned properly, the automatic feature is not an option. In that case, leave the TV power set to Manual. This means you must turn your TV on using its power button or with the LIFESTYLE remote (when it is set to do so). 8. Notice the TV Power Status: TV Detected means the installed TV sensor is working. TV Not Detected means the TV sensor (if installed) is not positioned properly, or a SCART connector is installed. Press System or Exit to leave the System menu. Note: For information on using the TV sensor, refer to Installing the TV on/off detector in your Installation Guide. To check for positioning of the sensor, refer to The media center on page 10
For cable/satellite control
While you can set the LIFESTYLE remote to control both cable and satellite boxes, you must designate one or the other, not both, in the steps below. The one connected to the CBL-SAT input on your media center is the one you should designate. So when you press the CBL-SAT source button and the On/Off button below it, you are operating that device. You can designate the other under AUX Device. Do this only if the device is connected to the AUX input on the media center, or the AUX input is not being used. Note: For general guidelines on using the LIFESTYLE System menu, refer to Using System Menus on page 29. Follow the process below: Turn on the cable or satellite box, whichever you are setting the remote to control. Turn on the TV and be sure to select the Video input on the TV for the media center. Then, using the LIFESTYLE remote control, press the CBL-SAT source button and follow the steps below: 1. Identify the device: From the Remote Control options in the System menu, select CBL/SAT Device. Move right and select either Cable or Satellite by pressing Enter. 2. Identify the brand: In the menu options on the left, select CBL/SAT Brand. Move to the right and up or down in the alphabetical list to locate your brand. Press Enter to select that brand. 3. Select the device code: From the menu options on the left, select CBL/SAT Device Code. Move right to select the first code. Press the CBL/SAT On/Off button on your LIFESTYLE remote. Press that button again. If the Cable or Satellite box turns off and on again, you have chosen the right code. If it does not turn off, select another code, and press the CBL/SAT On/Off button two more times.* When you have chosen the right code, press the Enter button. Press the System or Exit button to leave the System menu. When you complete these settings, you can use the CBL-SAT On/Off button to turn on your Cable or Satellite source and other LIFESTYLE remote buttons to operate it.

*Some manufacturers use a number of similar device codes. After selecting one, you may find you can turn your Cable or Satellite box on and off, but are unable to change channels or select Play or Pause. In that case, select a different device code that provides more control. 21
For VCR (or DVR) control English
The list of VCR brands and VCR codes include selections for DVRs as well. By following the instructions below, you can set the remote to control one or the other, but not both. If you have both a VCR and a DVR, setting your remote to control the DVR will provide more control options. Whether yours is a standalone DVR or is coupled with the VCR or Cable/Satellite box makes no difference. Note: For general guidelines on using the LIFESTYLE System menu, refer to Using System Menus on page 29. Follow the process below: Turn on your VCR or DVR. Turn on the TV and be sure to select the Video input on the TV for the media center. Then, using the LIFESTYLE remote control, press the VCR source button and follow the steps below. 1. Identify the brand. From the Remote Control options in the System menu, select VCR Brand. Move right into the list of brands and up or down to locate your brand of VCR or DVR. Press Enter to select that brand. 2. Choose a device code: In the menu options on the left, select VCR Device Code. Move right to select the first code. Press the VCR On/Off button on your LIFESTYLE remote. Press this button again. If the VCR or DVR turns off and on again, you have chosen the right code. If the VCR or DVR does not turn off and on, select another code, and press the VCR On/Off button two more times.* When you have chosen the right code, press the Enter button. Press the System or Exit button to leave the System menu. When you complete these settings and select VCR as the source, you can now use the VCR On/Off button and press Play, Pause, or Stop to control your VCR. If you have made the remote settings for a DVR, you can also use the Seek button on the LIFESTYLE remote. On some DVRs, pressing Shuffle and Repeat buttons will allow you to skip backward or forward quickly.

For AUX control

If you have a component connected to the AUX input on your media center, you can set your LIFESTYLE remote to control it, although on and off control is not an option. If you do not have a component connected to AUX, you can still control another device by selecting it from the list of AUX device choices: Changer, Satellite, Cable, DVR, TV or VCR. To exercise this control, you must press the AUX source button first. Note: For general guidelines on using the LIFESTYLE System menu, refer to Using System Menus on page 29.
*Some manufacturers use a number of similar device codes. After selecting one, you may find you can turn your VCR or DVR on and off, but are unable to change channels or select Play or Pause. In that case, select a different device code that provides more control. 22

Changing Source Settings Tuner setting options (FM or AM radio)
There are different settings menus for AM and FM. You can adjust the settings differently for each. Two of the attributes below are available only when the tuner is set to FM. FM (or AM) Features 2-3-5 Speakers Surround Center Channel Output Mode (FM-only feature) RDS Info (FM-only feature on some systems) Sleep TImer Default Setting; Options Effect of this Setting
5 Determines the number of speakers playing. 2, Establishes relative surround sound volume. -5 to +Establishes relative center volume. -5 to +5 Auto Sets channel distribution of radio signals. Mono or Stereo Off Displays station and program information On (as available from Radio Data System). Off Sets system to turn off when the selected 10-90 time elapses.

CD setting options

To see the CD Settings menu, you must insert a CD into the disc tray before you select the source. CD Features 2,3,5 Speakers Surround Center Channel Time Default Setting; Options Effect of this Setting
5 Determines the number of speakers playing. 2, Establishes relative surround sound volume. -5 to +Establishes relative center speaker volume. -5 to +5 0:00 Displays elapsed time. _:__ Advances or reverses the track to the new time. DTS Plays audio tracks in the format specified. Dolby Digital Off Sets system to turn off when the selected 10-90 time elapses.

Audio Track Sleep Timer

Changing Source Settings DVD setting options
To see the DVD Settings menu, you must insert a DVD into the disc tray before you select the source. Three attributes (shown in italic type below) appear in the DVD menu only if you have set Audio Processing to User Adjustable in the Audio options of the System menu. DVD Features 2,3,5 Speakers Surround Center Channel Movie EQ Range Compression Mono Decoding Time Title Chapter Audio Track Subtitle Language Camera Angle A B Repeat Default Setting; Options Effect of this Setting
5 Determines the number of speakers playing. 2, Establishes relative surround sound volume. -5 to +Establishes relative center speaker volume. -5 to +5 On Adjusts bass-to-treble relationship for proper Off movie soundtrack reproduction. On Adjusts volume to maintain dialogue intelligibilOff ity. Keeps some sounds from overwhelming others. On Engages Videostage 5 mono decoding circuitry Off to process mono programs (one-channel audio) into 5-speaker sound. 0:00 Displays elapsed time. _:__ Advances or reverses the film to the new time. Advances or reverses the film to another section _ of __ of the DVD, according to the number set. Advances or reverses the film to a new scene, ___ according to the number set. DTS Plays audio tracks in the format specified. Dolby Digital English Determines the language used for DVD subtitles Other (of the languages available on that disc). 1 of __ Determines the angle used for a movie scene (of the camera angles available on the disc). Repeats a segment of the DVD after the start A, B and end points are defined. To begin: 1. Move backward or forward to the point in the DVD where you want the segment to start. 2. 3. 4. Press Enter. Move to the point where you want it to end. Press Enter.

Using System Menus Audio options
Press the System button on the LIFESTYLE remote control. Move right to see a preview of audio features. Press the Enter button to move into an active display of submenus. Figure 12

Audio preview

Audio Select Audio to adjust these system options Bass Compensation Treble Compensation Audio Processing Input Levels ADAPTiQ Expansion Protocol
Note: Listening to an audio source while you make these adjustments can be helpful. Some changes will be immediately noticeable and therefore useful in fine tuning your selections. Default Settings; Options
Active Display Item Bass Compensation
0 Normal low-frequency reproduction. -14 to +14 Decreased (-) or increased (+) low-frequency reproduction. (-9 to +6) Range available following ADAPTiQ system calibration. 0 Normal high-frequency reproduction. -14 to +14 Decreased (-) or increased (+) high-frequency reproduction. (-9 to +6) Range available following ADAPTiQ system calibration. Automatic Standard Bose processing applied. User Adjustable Processing options available in Source Settings menus. Normal Standard signal level (loudness). -6, -3, +3, +6 Decreases or increases signal level (adjustable to match the levels of other components). Note: You may want to adjust the inputs of external components so they match the systems internal FM and CD levels.

Treble Compensation

Audio Processing (Movie EQ, Range Compression, Mono Decoding) TV Analog Input Level TV Digital Input Level VCR Analog Input Level VCR Digital Input Level CBL/SAT Analog Input Level CBL/SAT Digital Input Level AUX Analog Input Level AUX Digital Input Level

Using System Menus

Active Display Item ADAPTiQ Default Settings; Options Effect of this Setting
Off* No ADAPTiQ audio calibration performed. On Uses ADAPTiQ system adjustments established using Disc 2. Erase Eliminates the ADAPTiQ system adjustments* when this selection is followed, within 5 seconds, by a press of the Erase button on the media center controls. Bose link Communicates only with Bose link networked products. Legacy Communicates only with older Bose products.
Expansion protocol Change this only if instructed in the owners guide supplied with your Bose link remote control.
*The Off option for ADAPTiQ system is not a reversible selection. To restore the ADAPTiQ system adjustments requires re-use of the Setup Disc 2 and the ADAPTiQ headset supplied with the system. For information on this process, refer to Finishing the Installation in your LIFESTYLE Installation Guide. This advanced feature of the LIFESTYLE system makes adjustments to the audio processing to compensate for the furnishings, speaker placement, and listening positions to provide the most ideal sound in your room.

Miniature house code switches on the Main room (A) remote Switches (1-4) As set at the factory: all switches down.

Other switches

Switch 5 determines what stream or program you hear. For more information on streams, refer to Setting up a second room with sound below. Switches 6-9 represent the room where the remote will be used. In the main room, the remote is set as Room A with all switches down.
For a Bose link remote in another room
Switches 1-4 need to match those switch settings in your main remote. Set switches 5-9 for the room where you will use the Bose link remote.
Setting up a second room with sound
Your LIFESTYLE DVD home entertainment system can direct sound to more than one room at the same time. Whats more, it can even direct sound from two different sound sources (such as CD, AM/FM tuner, TAPE, or AUX) to these rooms through two independent streams. In other rooms with speakers (beyond the main room where the media center is located), you can choose either of these streams from different sources, for true independence. If the system is on in the main room, listeners in other rooms can enjoy the same program playing there or an entirely different program. Capable of supplying up to 14 addiitonal rooms with Bose sound, one LIFESTYLE system can fill your entire living space with music.
Bose link: the key to assured compatibility
One option is using a Bose product you already own, if you want the sound in just one additional room. As a second option that can provide sound throughout your home (or even outside!), the Bose link network connects all the pieces and offers a variety of Bose products of consistent quality for use in the other rooms. These include smaller Bose systems, powered and unpowered speakers and amplifiers, plus the proper cables and adapters to complete your sound network. And by purchasing a Bose link remote control for each additional room, managing your whole-house music system becomes quick and easy. Inside these remotes, one small switch allows you to predetermine which rooms, as a group, will share the main room program stream and which other room or group of rooms will hear the alternate stream. For more versatility, you may prefer using a PERSONAL music center II remote control in your other rooms. Besides providing the ability to switch between program streams without setting switches, this advanced remote provides an LCD screen that shows you what is playing on both steams. So it is very easy to choose one or the other whenever you like. Regardless of which type you choose, with any Bose link remote control you also get detailed instructions on using the network. And a Bose link symbol on the cartons (for the products mentioned above) helps simplify your selections. For more information on your choices, or to purchase additional equipment, contact your local Bose dealer. Or, to reach Bose directly, refer to the address list included with the system.

Radio does not work

The disc does not play
FM sound is distorted FM sound is noisy in surround mode Sound is distorted No sound from TV, CD/DVD, VCR, or AUX LIFESTYLE remote does not control your TV, VCR, cable/satellite box, or other external component
Your TV turns on and off unexpectedly
TV screen goes dark or image flips repeatedly after making a change to a Video feature in System settings You forgot your password
Contacting customer service
For additional help in solving problems, contact Bose customer service. See the address and phone number list included with your system.

Reference Accessories

For information on speaker mounting brackets and stands, additional remote controls, and connecting additional Bose powered loudspeakers, contact your Bose dealer or call Bose customer service. See the address and phone number list included with your system.

Technical information

Media center power pack power rating USA/Canada: 120V 0.55A 50/60Hz 33VDC International: 220-240V Dual voltage: 115/230V 0.30A 50/60Hz 33VDC 0.55A 50/60Hz 33VDC 1.1A 1.1A 1.1A
Speaker system power rating USA/Canada: 100-120V 50/60Hz 350W International: 220-240V Media center inputs AUX: 2Vrms, maximum CBL-SAT: 2Vrms, maximum VCR: 2Vrms, maximum TV: 2Vrms, maximum DIGITAL: SPDIF (1 each for TV, VCR, TAPE, and AUX) COMPOSITE VIDEO: NTSC or PAL format 1Vp-p with sync 75 S-VIDEO: Luminance 1Vp-p Chrominance 0.3Vp-p COMPONENT VIDEO: NTSC or PAL 1Vp-p with sync on Y OPTICAL INPUT: SPDIF digital, mapped to input FM ANTENNA: 75 AM ANTENNA: 12H TV SENSOR: Scan frequency sensing Media center outputs SPEAKER ZONES 1 and 2: Variable audio, user selectable AUDIO OUT L and R, fixed audio, 2 Vrms maximum DIGITAL AUDIO OUT: SPDIF OPTICAL OUTPUT: SPDIF, 15 to 21 dbm COMPOSITE VIDEO: NTSC or PAL 1Vp-p with sync 75 S-VIDEO: Luminance 1Vp-p Chrominance 0.3Vp-p COMPONENT VIDEO: NTSC or PAL 1Vp-p with sync on Y Media center dimensions 15.8"W x 11.0"D x 3.5"H (40.1 cm x 27.9 cm x 8.9 cm) Media center weight 8.2 lb (3.7 kg) Media center finish Aluminum Remote control range 65 ft (20 m) 50/60Hz 350W 50/60Hz 350W Dual voltage: 100-120/220-240V
2004 Bose Corporation, The Mountain, Framingham, MA 01701-9168 USA 274397 AM Rev.00 CCM-000393

LIFESTYLE DVD Home Entertainment Systems Installation Guide

Safety Information

WARNING: To reduce the risk of fire or electric shock, do not expose the system to rain or moisture. WARNING: This apparatus shall not be exposed to dripping or splashing, and objects filled with liquids, such as vases, shall not be placed on the apparatus. As with any electronic products, use care not to spill liquids in any part of the system. Liquids can cause a failure and/or a fire hazard.

CAUTION UT

RISK OF ELECTRICAL SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

AV I S V

RISQUE DE CHOC LECTRIQUE NE PAS OUVRIR ATTENTION : POUR RDUIRE LE RISQUE DE DCHARGE LECTRIQUE, NE RETIREZ PAS LE COUVERCLE (OU LARRIRE). IL NE SE TROUVE LINTRIEURAUCUNE PICE POUVANT TRE RPARE PARLUSAGER. SADRESSER UN RPARATEUR COMPTENT.
These CAUTION marks are located on your LIFESTYLE media center and Acoustimass module enclosures: The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the system enclosure that may be of sufficient magnitude to constitute a risk of electric shock. The exclamation point within an equilateral triangle, as marked on the system, is intended to alert the user to the presence of important operating and maintenance instructions in this installation guide.

Class 1 laser product

The DVD player contained within the media center is classified as a CLASS 1 LASER PRODUCT according to EN 60825-1:1994 + A11. The CLASS 1 LASER PRODUCT label is located on the bottom of the media center.
CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER LASER LASER LASER PRODUCT PRODUKT LAITE APPARAT
CAUTION: Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. The compact disc player should not be adjusted or repaired by anyone except properly qualified service personnel. CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus. Class B emissions limits
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.

Batteries

Please dispose of used batteries properly, following any local regulations. Do not incinerate.
Additional safety information
See the additional instructions on the Important Safety Information sheet enclosed in the shipping carton.
Please read this installation guide
Please take the time to follow this installation guide carefully. It will help you set up and operate your system properly, and enjoy all of its advanced features. Save your installation guide for future reference.

System Information

Serial numbers are located on the bottom of the media center and the bottom panel of the Acoustimass module.
System: (circle one) LIFESTYLE 18 system LIFESTYLE 28 system LIFESTYLE 38 system LIFESTYLE 48 system
Media center serial number: _____________________
Acoustimass module serial number:___________________ Purchase date: ____________
Dealer name: ___________________________ Dealer phone: ___________________ Be sure to fill out your product registration card and mail it to Bose.
Bose recommends that you keep your sales slip and a copy of your product registration card together with this guide.
2004 Bose Corporation. No part of this work may be reproduced, modified, distributed or otherwise used without prior written permission. Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished Works. 1992-1997 Dolby Laboratories. All rights reserved. DTS and DTS Digital Surround are registered trademarks of Digital Theater Systems, Inc. MPEG Layer-3 audio compression technology licensed by Fraunhofer IIS and THOMSON multimedia. This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited. This product incorporates copyright protected technology and other intellectual property rights owned by Cirrus Logic, Inc. and is subject to the copyright protection of the U.S. as well as other licensing restrictions and protections. Use of this copyright protected technology is limited solely to use with the Cirrus Logic integrated circuits incorporated in this product. Reverse engineering or disassembly is prohibited.

Contents Where to find

Introduction. Before you begin. Special indicator used in this book. Unpacking. System Installation. Cables and accessories. Placing your speakers. Left and right front speaker placement. Center speaker placement. Surround speaker placement. Acoustimass module placement. Placing your media center. Connecting the speakers to the Acoustimass module. Connecting the plug-in cable to Jewel Cube speakers. Making the two-wire connections for cube or cube array speakers. Connecting the Acoustimass module to the media center. Connecting the antennas. Connecting the FM antenna. Connecting the AM antenna. Connecting to a cable radio provider. Connecting your TV to the system. Making the audio connection. Making a video connection. Selecting the proper TV video input. Turning off the speakers in your TV. Connecting the system to power. Installing the remote control batteries. Finishing the basic installation. Installing the TV on/off sensor. Reference. Using alternate video connections. Connecting your VCR to the system. Connecting your cable/satellite box to the system. Using Component video connections. Connecting a game console. Connecting other components. Connecting record/playback equipment. Connecting other playback equipment. Using digital audio connections. Other jacks on the media center panel. Connecting an optional antenna extender. Connecting the optional IR emitter cable. Data port for system backups. Serial data jack. Expanding your system to other rooms. How to decide what to add. How you make it all work together. Accessories. Limited warranty. Contacting customer service. Technical information. 34

Safety Information.

Introduction Before you begin

English

Thank you for your purchase of a Bose LIFESTYLE DVD home entertainment system. It will serve as the center of your home theater, providing superior audio performance for music and movies. There are four different systems, the LIFESTYLE 18 Series II, LIFESTYLE 28 Series II, LIFESTYLE 38, and the LIFESTYLE 48 systems. All include multiple room connections, most include the AdaptiQ audio calibration system, and the LIFESTYLE 38, and LIFESTYLE 48 systems have the uMusic intelligent playback system. This book shows you: The components included with your system and how to set the system up. The pictures on the next two pages will help you become familiar with each part of your system. First you will set up the audio portion of the system. You will find the best locations for your media center, cube speakers, and Acoustimass module. You will identify and connect the cables that are specific to each part of the system, the AM and FM antennas, and the power cords. How to make a basic connection between your LIFESTYLE system and your television, which will allow you to see the on-screen menus. Your Operating Guide offers information on other aspects of the use of your system. How to power up the system and optimize its sound for the component placement you have selected in your room. How to connect other pieces of equipment, such as VCRs, cable or satellite boxes, DVD changers, game consoles, and recording equipment, to make an even more versatile home theater system. The instructions in this section help you connect your system in your main room. However, if you wish to extend your systems sound to other rooms, read the special considerations in Expanding your system to other rooms on page 32 before you make any connections.

Special indicator used in this book
A box with dotted lines identifies parts which vary with different systems or in different countries.

Unpacking

After unpacking your new system, save all packing materials; they may be useful as a safe way to transport your system. If any part of your system is missing or appears damaged, contact your authorized Bose dealer immediately, or contact Bose directly. Refer to the Bose address list included in the carton. The drawings on these pages show the components of several LIFESTYLE DVD entertainment systems. Your system will have one of the three types of cube speakers shown.

System Installation

Figure 1
Components of the LIFESTYLE DVD systems
Media center power supply Media center Rubber foot for Jewel Cube speaker
Your system will have five of one type of cube speaker:
or Single cube speaker (LIFESTYLE 18 Series II system)
Cube speaker array (LIFESTYLE 28 Series II & LIFESTYLE 38 systems) Remote controls
On Off Mute All Mute On Off Mute All Mute
Jewel Cube speaker (LIFESTYLE 48 system)

CDDVD TV

Input On Off

FMAM CBLSAT

On Off

AUX VCR

Stored TV
Rubber feet for cube speakers
DVD Menu ENTER Settings Guide

Library ENTER Settings

DVD Menu
System Track Chapter Preset Channel

Volume

Seek Shuffle Repeat Shuffle

Seek Repeat

uMusic

Rating Similar Whole CD

Playlist

LIFESTYLE 18, 28 systems

LIFESTYLE 38, 48 systems

Acoustimass module

Rubber feet for Acoustimass module
Media center power supply AC power cord
Acoustimass module AC power cord
120 VAC power cord (US/Canada)
230 VAC power cord (Europe)
230 VAC power cord (UK/Singapore)
240 VAC power cord (Australia)
115/230 VAC dual power cords (US/Europe)
System Installation Cables and accessories

Figure 2

Cables and accessories included with your system
Front speaker cables Surround speaker cables

Audio input cable

Two component video adapters Stereo audio cable S-Video cable

FM antenna

Video cable (6 ft)

AM loop antenna

IR emitter cable

Setup disc 1

Recommended speaker locations Center Left front Right front

Left surround

Right surround
Note: If the center, left, or right front speakers will be in a bookcase unit, be sure to place them at the front edge of the shelf. Placing speakers in an enclosed space can change the tonal quality of the sound.

Figure 4

Cube speaker array placement and reflection rays Left front Center Right front Acoustimass module

Figure 5

Single cube speaker placement and reflection rays Left front Center Right front Acoustimass module

Center speaker placement

The center speaker sound should seem to come directly from the center of the picture. The center speaker cable allows up to 20 feet (6.1 m) distance from the Acoustimass module. 1. 2. Place the center speaker directly above or below the center of the TV screen, or at the closest convenient location. Align the speaker with the front of the TV screen (not pushed to the back of the TV).
Note: If placed on top of the TV, attach the protective rubber feet to the bottom of the center speaker.
Surround speaker placement English
The rear surround speakers create an area of sound around the listener. Place them in the back half of your room. Direct both cubes of the speaker array (or your single cube speaker) away from the listeners so that they cannot pinpoint the exact location of the sound source. The surround cables allow up to 50 feet (15.2 m) distance from the Acoustimass module. 1. 2. Place the speakers at ear height (when seated) or higher, if possible. Adjust the rear surround speakers to reflect sound off one or more surfaces.
The longer the path from the speaker to your ear, the better. Do not direct the sound straight at the listener. Note: Bose offers a variety of speaker mounting accessories, including stands and wall brackets. For further information, or to purchase accessories, contact your local Bose dealer or visit www.bose.com. To contact Bose, refer to the address sheet included with your system.
Acoustimass module placement
Note: If the serial number on the bottom of the Acoustimass module is not already printed on your Product Registration card, now is a good time to record it there and in the space provided on page 3 of this guide. Follow these guidelines to select a location for the Acoustimass module: Place the Acoustimass module along the same wall as the TV, or at the same end of the room as the front speakers (refer to Figure 4). Note: To avoid interference with the TV picture, place the Acoustimass module at least 18 inches (45 cm) from the TV. Move it further if you still notice interference. Place the Acoustimass module so that the grille with the Bose logo faces the room or is perpendicular to the wall. This prevents blocking the sound output or creating too much bass. For best bass performance, DO NOT place the Acoustimass module at equal distances from any two walls or centered between the floor and ceiling. For convenience, you may want to slide the Acoustimass module under a table or behind a cabinet. However, DO NOT allow furniture or drapes to block its ventilation openings. CAUTION: DO NOT BLOCK the slots on the end the module, which provide ventilation for the built-in electronic circuitry. Place the Acoustimass module within reach of the audio input cable, speaker cables, and an AC power (mains) outlet.

Put any side of the Acoustimass module on the floor. DO NOT stand it on either end (Figure 6).

Figure 6

Right and wrong placements for the Acoustimass module
BEST For best ventilation, stand it on the narrow side with the connectors facing the floor.
DO NOT stand the module on its slightly curved back end, which can cause it to tip over. DO NOT stand the module on its front grille end. The weight of the module can damage the grille.
ALTERNATE Or, place it on one of the two broad sides.

Ventilation openings

Once you have selected a position for the module, place the four self-adhesive rubber feet near the corners of the bottom surface. The rubber feet provide increased stability and protection from scratches. CAUTION: The magnetic field from the Acoustimass module is not a short-term risk to your video tapes, audio tapes, and other magnetic media. However, you should not store tapes directly on or near the Acoustimass module.
Placing your media center
Note: If the serial number on the bottom of the media center is not already printed on your Product Registration card, now is a good time to record it there and in the space provided on page 3 of this guide. Note: Sending in the product registration card, included with your system, is very important if you want to receive software updates. Be sure to fill out the card and mail it to Bose. Select a location for the media center, keeping in mind the following guidelines: Do not block the front of the media center. Allow enough room to lift up the front cover and open the CD/DVD tray. Also, be sure you have a clear view of the display window on the front of the media center (Figure 7). Place the media center close enough to other sound sources (TV and VCR) to allow for easy cable connections. If you need additional audio or video cables to connect your components, see your dealer or call Bose customer service. Refer to the Bose address list included with your system. Place the media center within 30 feet (9.1 m) of the Acoustimass module (the length of the audio input cable). Note: For convenience, until your system is completely installed, you may wish to place the media center where you have easy access to its rear connection panel.

Figure 7

Front features of the media center Front door Make sure you have enough room to lift this door. Display window Make sure you can see this information while using your system.
Disc tray Make sure nothing blocks this CD/DVD tray as it slides open.
The IR Emitter, which enables certain remote control operation, is located here.
Connecting the speakers to the Acoustimass module
CAUTION: Before you make any connections, be sure that the media center, the Acoustimass module, and any additional equipment are not connected to AC power. Your system may have Jewel Cube speakers (image A on the left), which use a plug-in cable connect, or cube array or single cube speakers (images B and C respectively,) which use a two-wire cable. LIFESTYLE DVD systems include five speakers.

Left, Right, or Center printed on the red collar on (+) wire
Connect each cable to the corresponding jack on the Acoustimass module (Figure 10). Plug the blue connectors into the matching left front, center, and right front jacks. Plug the orange connectors into the matching left surround and right surround jacks.

Figure 10

Speaker connections to the Acoustimass module Left

Front speakers Center

Surround speakers Left Right

FRONT L

FRONT C

FRONT R

SURROUND L

SURROUND R

AUDIO INPUT
OUTPUTS TO CUBE SPEAKERS FRONT SURROUND
100-120/200-240VAC 50/60 Hz 350W MAX.
Acoustimass module connector panel
Note: You may find it more convenient to place the Acoustimass module upside down while making connections. When done, place it on any of its sides but not on either end or top.
System Installation Connecting the Acoustimass module to the media center
Connect the Acoustimass module to the media center with the audio input cable (Figure 11). Note: Be sure that each connector is fully inserted into each jack. 1. 2. 3. You may find it easier to insert the power adapter cord into the media center first. Do not plug the other end into an AC (mains) power outlet until all connections are completed. Plug the small black multi-pin connector (flat side up) into the Speakers jack labeled Main on the back of the media center. Insert the telephone-style RJ-45 connector on the other end of the audio input cable into the Audio INPUT jack on the Acoustimass module. When properly inserted, it locks in place.
Note: An antenna is built into the media center power cord; be sure to unwrap the power cord for the best remote control operation (Figure 11). Note: Refer to Expanding your system to other rooms on page 32 for information on connecting a second room. Figure 11
Acoustimass connection to media center Media center connector panel

Power adapter cord

Note: When fully inserted into the jack, the connector locks in place. To release the cable connector, press the tab.

System Installation Connecting your TV to the system
The instructions below show basic connections to the media center and TV. This simple set of connections will allow you to use your system quickly. Later in this guide you will find other options for connecting additional components to your system.
Making the audio connection
Using the supplied stereo audio cable, connect the left (L) and right (R) audio outputs on the rear panel of your TV to the Audio IN TV L and R on the media center rear panel (Figure 12). If the TV has both fixed (FIX) and variable (VAR) outputs, use the ones for fixed output. If the setup menu for your TV allows, select Fixed in that menu. If you have a digital TV, you may connect a digital audio cable as well. This may either be a single coaxial cable with RCA connectors on each end, or an optical cable, which has a unique snap fit connector on each end. Note: It is important to provide the analog connection along with the digital, to prevent a loss of sound caused by any temporary degradation of the digital signal. Note: On the TV, be sure to notice which Video IN jack is used. In the example below, the media center Video OUT is connected to the VIDEO 1 input on the TV. In this case, use your TV remote control to select VIDEO 1 to view DVDs and see LIFESTYLE system menus. Figure 13
Composite video connection
Cable TV, Satellite, or Antenna cable Component video connections are explained later in this guide
The connection panel on your TV may look different. It may have fewer Video IN connections
This audio connection allows your TV to send sound to your LIFESTYLE system
This video connection allows you to view DVDs and see system menus

Media Center

Making a video connection English
On your Media Center, connect the Composite Video Out to a Video In connection on your TV. See Figure 13. Use a single cable with a yellow RCA connector on each end. Remember the connection you used on your TV, such as VIDEO 1 or VIDEO 3, because that is the video input you must select, using your TV remote, to see a DVD picture or LIFESTYLE system menus on your TV.
Selecting the proper TV video input
To view the DVDs and LIFESTYLE system menus on your TV, you will need to select the input which connects the media center to the TV. Until your LIFESTYLE remote control has been taught to control your TV, use the TV remote control. With the TV remote control, press the TV input button. It may be called TV/VIDEO, Source, or Input. You may have to press it more than once, depending on which numbered connection you used. Note: Refer to the Controlling External Sources section in your Operating Guide for information on how to set the LIFESTYLE remote to control the TV.

Remote control battery installation Four (4) AAA (IEC-LR3) batteries
Battery compartment cover
Replace all four batteries when the remote control stops operating or its range seems reduced. Alkaline batteries are recommended. Your remote control will need to be taught to control external components of your home theater, including your TV. See your Operating Guide for details.
System Installation Finishing the basic installation
Your system comes with two compact discs. Figure 17
Setup discs and AdaptiQ audio calibration system Setup Disc 1 Setup Disc 2 ADAPTiQ audio calibration system
ADAPTiQ calibration headset
Setup Disc 1 provides information about your system and verifies that your speakers are connected correctly. Setup Disc 2 leads you through the ADAPTiQ audio calibration process, which tailors the sound of your LIFESTYLE system and your speaker placement to the acoustics of your listening area. The special headset, designed to be worn above your ears, enables you to take acoustic measurements during the process. Put it on only when Disc 2 indicates. Play both discs when everything is in place and you have made all of the connections. Allow approximately 20 minutes to complete the process. You may want to do it when the acoustic measurements will not disturb anyone. Note: The 220-240V LIFESTYLE 18 Series II system includes Disc 1 only. Owners of that system do not need to follow the instructions for Disc 2 below.
Using the ADAPTiQ audio calibration system 1. Use the TV remote to turn on your television.
2. 3. 4. 5. 6. 7. Figure 18
Using the AdaptiQ calibration headset
Select the video input connected to the LIFESTYLE system media center. Lift up the media center front cover and press the Open/Close button. Insert Setup Disc 1 into the tray (label side up) and press the Open/Close button again. On the remote control, press the CD/DVD button. As the disc begins to play, listen carefully and follow the instructions. You will be instructed when to play Disc 2. When Disc 2 indicates, connect the ADAPTiQ calibration headset to the AUX jacks on the connection panel of the media center as shown below.

Reference Using alternate video connections
This section shows you how to set up your home theater system to incorporate additional components, such as VCRs and Cable/Satellite boxes. It also explains different ways to make the connections. Make audio connections from components to the media center. There are three different types of audio connections: the analog (L and R) connection you are probably familiar with, and two types of digital connections, either a coaxial digital (single cable with RCA connectors at each end), or an optical connection. See Using digital audio connections on page 30. A composite and an S-Video connection or a single component connection can be made from the media center to the TV. Your choice of connection will depend on your preference and the type of jacks provided on your TV. Explanations and diagrams on the following pages show variations that you may use in your home theater setup. Connect other video devices directly to the TV. The remaining video connections go directly to the TV (assuming it has multiple connection jacks on its back panel). Composite video This is a standard video input on televisions. To make this connection, use the supplied Video cable (with yellow connectors) to go from the Composite Video OUT on the media center and to a video input jack on your TV. Be sure to note which jack you use on the TV. S-Video An S-Video input jack, provided on many TVs, delivers higher picture quality than composite video output. To make this connection, use the S-Video cable included with your system to connect the S-Video OUT jack on the media center and to the S-Video input on your TV. Component video If your want to use the systems progressive scan feature and your TV has component jacks, you will need to use one of the two Component video adapters provided with your system (Figure 20). This adapter takes three separate video signals (Y, Pr, and Pb) from the media center and makes them available on standard video jacks. The adapter uses both Video out jacks on the media center, so you can only make one component connection to the TV. Video-grade cables from these jacks are not supplied and you will need to purchase them separately. Note: For more information, or to purchase the video cables, contact your local electronics store or authorized Bose dealer. Figure 20
The Bose component video adapter Media center
S-VIDEO OUTPUT COMPOSITE VIDEO OUTPUT

Component video adapter

Video cables

TV Component video jacks Y (Green) Pr (Red) Pb (Blue)
To make Component video connections: Plug the two-connector end of the adapter into the S-Video and Composite OUT jacks on the media center. Connect the other end of the adapter to video-grade cables. Connect the free ends of the video cable to the Y, Pb, and Pr jacks on your TV, matching the colors on the adapter appropriately. Note: You need to turn on the progressive scan feature using the display on your media center. To do this, see "Making it all work smoothly in your Operating Guide." You will also need to set your TV for progressive scan. Follow the instructions that came with the TV.
Reference Connecting your VCR to the system
The rear panel of the media center provides audio and video connections for your VCR. Note: If you have already used the video and audio cables supplied with your LIFESTYLE system, or your VCR does not provide any, you need to purchase additional cables. Contact your local electronics store or authorized Bose dealer. Most VCRs have a Composite video output, which is the type of connection explained below. Follow these steps to make the VCR connections: 1. 2. Using audio cables, connect the left (L) and right (R) audio outputs on your VCR to the L and R VCR Audio IN jacks on the media center rear panel. Using a video cable, connect the VCR (Video OUT) to the media center (Composite Video IN). Then use another cable to connect the media center (Composite Video OUT) to the TV. Cable TV, satellite, or antenna cable TV

IN OUT

Figure 21

VCR connection

The media center may also be connected to a different input on the TV using an S-Video cable.
You can use an S-Video cable to connect the media center (Video OUT) to your TV, for higher DVD picture quality. The composite connection made in Step 2 above will pass the VCR video to the TV. Remember to select the proper TV input when you change from watching video tapes to DVDs and vice versa. If your media center is connected to the TV using the Component video adapter, you cannot connect a VCR to the media center. Connect it directly to another input on the TV and select that input on the TV to watch videotapes.
Reference Connecting your cable/satellite box to the system
There are various ways to make the cable/satellite connections: 1. Connect cable/satellite L & R Audio OUT to the L & R Audio IN jacks on the media center. If the cable/satellite box has a DIGITAL Audio OUT jack, connect it to the CBL/SAT DIGITAL Audio IN jack on the media center. 2. If the cable/satellite box has an S-VIDEO OUT jack, connect it to the S-VIDEO IN jack on the media center. Use another S-VIDEO cable to connect the S-VIDEO OUT jack on the media center to an S-VIDEO jack on the TV. If the cable satellite box has only a composite VIDEO OUT jack, connect that to the composite VIDEO IN jack on the media center. Connect a VCR to this system as follows: 1. 2. If your cable satellite box has an additional set of Audio and VIDEO OUT jacks connect them to the corresponding Audio and VIDEO IN jacks on your VCR. Connect the VCR to the VIDEO IN jack on the media center. If that jack is unavailable, connect the VCR directly to the TV.

In Figure 22, select Input 2 on your TV to watch cable/satellite programs. Select the CBL/SAT sound source. This input will also provide better video quality when watching DVDs. To watch videotapes, select Input 1 on your TV (or the TV input to which you directly connected the VCR) and select the VCR sound source. Note: Additional cables may be purchased at an electronics store or authorized Bose dealer. Figure 22

Set top box and VCR

Cable TV, satellite, or antenna cable
If the CBL/SAT box has only a composite VIDEO OUT jack, connect that to the composite VIDEO IN jack on the media center.Connect the VCR composite VIDEO OUT directly to the TV.

Reference

Using Component video connections
Follow the connection diagram in Figure 23 to achieve the best video quality for DVD and cable/satellite viewing, while adding a VCR to your home theater. Refer to Component video on page 24, if necessary. To watch DVDs and see LIFESTYLE system menus, select the VIDEO 4 input on your TV, or, if your cable/satellite box has component jacks, connect them as shown in the diagram and select VIDEO 4 on your TV. Select CBL/SAT on your LIFESTYLE system remote. Connect the VCR (VIDEO OUT) to an available VIDEO IN jack on your TV. Select that TV input. Connect the VCR (Audio L and R OUT) to the TV Audio IN jacks on the media center and select the TV source on your LIFESTYLE system remote. Figure 23
Component video connection
Note: To make the connections shown in the diagram below, you will need additional cables.
Note: Two comonent video adapters are provided.
Connecting a game console English
Connect a game console directly to an available TV input. To play, select that TV input and select TV audio on your LIFESTYLE system remote. See Figure 24. Figure 24
Connecting a game console
Reference Connecting other components
Use standard RCA audio cables, matching the white (or black) connector to the L (left) channel and the red connector to the R (right) channel. See Figure 25. If the component is mono, use a Y adapter to connect it to the media center. Appropriate cables and adapters are available at most electronic stores. If the component has a digital output use the corresponding digital input beneath the set of analog (L and R) inputs. You could also use an optical connection, if the component has one. See Figure 27. You must identify the optical source using the System/Media Center/Optical Source menu.

Connecting the optional IR emitter cable
The IR (infrared) emitter cable is designed for optional use when a particular component does not respond to LIFESTYLE system remote control commands. That is, the component is connected to the media center, but placed where it cannot receive the IR signals from the media center. The IR emitter can be placed next to one component only. See Figure 27 on page 30. To use the emitter: 1. 2. Insert the 3.5 mm plug into the IR EMITTER jack on the media center panel. Place the flat side of the other end of the cable near the unresponsive component so that the remote control signals reach that component.
Note: Refer to Controlling external sources in your LIFESTYLE system Operating Guide for details on how to program the LIFESTYLE system remote so that it works with your other component. 3. 4. Confirm that IR signals now work to control that component. Move the emitter around, as necessary, to find the best position. Use the double-sided tape enclosed with the emitter to affix it in the proper position.
Note: If you have questions, or need to obtain a replacement emitter, contact Bose customer service. Refer to the Bose address list included with your system.
Data port for system backups
Some systems will have a data port for future use. See Figure 27.

Serial data jack

This jack is for factory and service use only.
Reference Expanding your system to other rooms
Your media center provides two audio output jacks. One sends audio to the speakers connected to the media center in the main room. The other jack, labeled BoseLink Speakers, connects other speakers in other rooms. Special Bose link cables are available for that connection. The cable allows you to take advantage of an advanced system capability. You can send separate programs from two separate sources to different rooms throughout your house.even outdoors. The Bose link network can incorporate a variety of Bose speakers and systems, using available Bose custom cables and adapters. See "Setting up a second room with sound" in your Operating Guide.
How to decide what to add
One option is using a Bose product you already own, if you want sound reproduced in just one additional room. To adapt legacy (pre-existing) Bose products for this purpose, you need to know: Powered Acoustimass 5 or Acoustimass 20 speakers require a variable RCA to DIN cable. Lifestyle stereo amplifier, Model SA-2 or SA-3, for use with passive Bose speakers, restricts to one pair the number of speakers you can add. Any Wave radio or other existing Bose stereo system requires use of a variable cable adapter. To properly connect and control additional speakers, you need: Another LIFESTYLE system remote control to adjust the volume and turn the additional set of speakers on and off. Appropriate LIFESTYLE system cables to connect the added speaker system. For further information, or to purchase compatible equipment, see your Bose authorized dealer. Or, to contact Bose directly, refer to the address list provided with the system.

1.0 lb (0.5 kg)

8.0"W x 24.5"D x 16.0"H 35.9 lb (16.3 kg) (20.3 cm x 62.2 cm x 40.6 cm)
2004 Bose Corporation, The Mountain Framingham, MA 01701-9168 USA 274398 AM Rev.00 CCM-000363