BOSS ME-25 GUITAR MULTIPLE EFFECTS TRAINING GUIDE
Contents 1. FEATURES 2. QUICK DEMO 3. GOING DEEP 4. FIVE FEATURES TO KNOW and SHOW 5. ACCESSORIES 6. ME-25 EFFECTS
BOSS ME-25 Training Guide
1. FEATURES Super simple operation COSM amp and effect modeling Functions as USB-audio interface New SOUND LIBRARY Interface allows downloadable patches from dedicated website Comes with Cakewalk Sonar LE recording software and hundreds of loops and rhythms for jamming or recording 7 Effect groups: Preamp, Comp/FX, OD/DS, Modulation, Delay, Reverb, Pedal FX 10 COSM amplifier models 3 Comp/FX effects 8 Modulation effects, including Uni-V, Harmonist and Rotary 4 delay ranges w/ up to 6,000ms delay time Built in 38-second Phrase Looper w/ unlimited overdubs 60 programs-all programmable Built-in assignable Expression pedal Built-in chromatic tuner Tough metal case Runs on batteries (included) or optional BOSS PSA-120S AC adaptor $276.50 List, $199 MAP

2. QUICK DEMO

The Quick Demo is a way to get a customer interested in a product in less than 60 seconds.

Before You Start

1. Connect the MONO (L) output of the ME-25 to the clean channel of a good amp, such as a Roland JC-120 or other pro quality amp. NOTE: It is very important to use a pro-quality guitar amp. Why run a highend effect through a low-end amp? 2. Set the amps tone controls for a flat response. 3. Connect the ME-25 to power using a BOSS PSA-120 AC Adaptor. 4. Plug a guitar into the GUITAR INPUT of the ME-25.
THE QUICK DEMO: SHOW the SOUND LIBRARY
1. Press the CLEAN BUTTON. The LED will light up.
2. Turn the VARIATION KNOB to select a CLEAN variation.
3. Play the sound 4. Turn the PARAMETER KNOBS to adjust the sound. 5. Turn the DRIVE, TONE and VOLUME (PARAMETER 1, 2, 3) KNOBS to adjust the sound.
6. Press the DRIVE BUTTON.
7. Turn the VARIATION KNOB to select a variation. 8. Play the sound. 9. Turn the DRIVE, TONE and VOLUME KNOBS to adjust the sound 10. Press the EXTREME BUTTON.
11. Turn the VARIATION KNOB to select a variation. 12. Turn the DRIVE, TONE and VOLUME KNOBS to adjust the sound.

3. GOING DEEP

How to EDIT the ME-25 1. Hold down EXIT and press WRITE to engage the EDIT MODE.
2. Press DRIVE (Preamp) or another SOUND LIBRARY BUTTON.
3. Turn the VARIATION (Type) KNOB to select a TYPE. NOTE: all the EFFECT TYPES are printed on the ME-25 below the SOUND LIBRARY BUTTONS.
4. Check out the sound 5. Turn the PARAMETER 1,2,3 KNOBS to adjust the sound. 6. Follow the above steps to check out other preamp sounds or other effect sounds. 7. Press EXIT when finished.
How to Change Programs 1. Press the MEMORY UP or MEMORY DOWN PEDALS. How to Use the Tuner 1. Press the MEMORY UP and MEMORY DOWN PEDALS down simultaneously. 2. Tune up. The note played will show in the LED Display. The LEDs in the display will indicate whether the note is sharp, flat, or in tune. 3. Press the MEMORY PEDALS again to return to play mode. How to Use the PHRASE LOOPER 1. Hold the SOLO PEDAL down for two seconds. The LED will flash indicating Standby mode. 2. When you are ready to play, press the SOLO PEDAL. The LED will flash quickly indicating Recording mode. 3. To end the loop and play it back, press the SOLO PEDAL again. The LED will stay on to indicate Playback mode. 4. Repeat steps two and three to overdub. 5. Press the SOLO PEDAL twice quickly to stop playback and return to Standby. 6. Hold the SOLO PEDAL down for two seconds to exit the PHRASE LOOPER. How to Re-Initialize the ME-25 1. Hold down EXIT and press the MEMORY DOWN PEDAL. The display will show FA. 2. Press WRITE. The TUNING guide will flash. 3. Press WRITE again.

4. FIVE THINGS TO KNOW and SHOW
1. Super simple but full featured BOSS multi-effect 2. COSM modeled Amps, OD/DS, Modulations, and Delays 3. USB-Audio interface 4. Comes with Cakewalk Sonar LE professional recording software and DVD-ROM with on screen Librarian and hundreds of loops and rhythms for jamming or practice 5. Battery or AC operation-use it any time, anywhere

5. ACCESSORIES

1. BOSS PSA-120S AC Adapter 2. Roland RH-5, RH-200 or other headphones 3. Instrument cables

6. ME-25 EFFECTS

COMP/FX 1. COMPRESSOR 2. T-WAH 3. ACOUSTIC SIMULATOR OD/DS 1. BOOST 2. OD-1 3. T-SCREAM 4. BLUES 5. DIST 6. CLASSIC 7. MODERN 8. METAL 9. CORE 10. FUZZ PREAMP 11. CLEAN 12. TWIN 13. TWEED 14. VO DRIVE 15. BG LEAD 16. MS VINTAGE 17. MS MODERN 18. 5150 DRIVE 19. R-FIER 20. ULTRA-METAL MODULATION 1. CHORUS 2. PHASER 3. FLANGER 4. ROTARY 5. UNI-V 6. TREMOLO 7. HARMONIST 8. OCTAVE DELAY 1. 1-99ms 2. 100-990 ms 3. 1000-6000m 4. Tap ORIGINAL BOSS CS-3 BOSS AW-3 BOSS AC-3 Original level booster BOSS OD-1 Ibanez TS-808 Tube Screamer BOSS BD-2 BOSS DS-1 BOSS DS-2 BOSS w/ Turbo on BOSS MT-2 BOSS ML-2 BOSS FZ-5 Roland JC-120 Fender Twin Reverb Fender Bassman 4x10 Vox AC-30TB Mesa-Boogie II c Marshall Plexi Marshall JCM 800 Peavey EVH 5150 lead channel Mesa-Boogie Dual Rectifier Original super heavy metal amp BOSS H-1 BOSS PH-3 BOSS BF-3 Leslie 147 Univox Uni-vibe BOSS TR-2 BOSS PH-5 BOSS OC-3
REVERB 1. ROOM 2. HALL PEDAL EFFECTS 1. WAH 2. +1 OCTAVE 3. 1 OCTAVE 4. FREEZE NOISE SUPPRESSOR SUPER STACK

BOSS ME-70 GUITAR MULTI-EFFECTS TRAINING GUIDE
Contents 1. FEATURES 2. QUICK DEMO 3. GOING DEEP 4. FIVE FEATURES TO KNOW and SHOW 5. ACCESSORIES 6. ME-70 EFFECTS
BOSS ME-70 Training Guide
1. FEATURES Super simple knob-based operation COSM amp and effect modeling Defaults to Manual Mode for use as virtual stomp boxes 8 Effect groups: Preamp, Comp/FX, OD/DS, Modulation, Delay, Reverb, Pedal FX, NS 6 COSM amplifier models plus 4-band EQ 8 Comp/FX effects 10 Modulation effects, including Uni-V, Harmonist and Rotary 10 delay types w/ up to 6,000ms delay time, including Analog and Reverse Built in 38-second Phrase Looper w/ unlimited overdubs Modulation and Delay effects support tap tempo 72 programs-36 user, 36 preset Built-in assignable Expression pedal Built-in chromatic tuner Tough metal case Runs on batteries (included) or optional BOSS PSA-120S AC adaptor $418.50 List, $299 MAP

2. QUICK DEMO

The Quick Demo is a way to get a customer interested in a product in less than 60 seconds.

Before You Start

1. Connect the MONO (L) Gt. AMP output of the ME-70 to the clean channel of a good amp, such as a Roland JC-120 or other pro quality amp. NOTE: It is very important to use a pro-quality guitar amp. Why run a highend effect through a low-end amp? 2. Set the amps tone controls for a flat response. 3. Connect the ME-70 to power using a BOSS PSA-120S AC Adaptor. 4. Plug a guitar into the GUITAR INPUT of the ME-70. 5. Make sure the ME-70 is in MANUAL MODE. 6. Turn all ME-70 effects off.
THE QUICK DEMO: USING THE ME-70
This Quick Demo has five steps. You can do some or all of the steps.
STEP ONE: Add Distortion 1. Make sure that all the effects are off; then play the guitar through the ME70 to show the dry sound. 2. Select a DISTORTION or OVERDRIVE type by rotating the OVERDRIVE/DISTORTION TYPE KNOB.
3. Set the OD/DS control knobs to an appropriate setting.
(Not suggested settings. For illustration only )
4. Press the OD/DS PEDAL to turn on the Overdrive.
5. Play some chords or leads.
STEP TWO: Add Modulation 1. Turn the MODULATION TYPE knob to select a Modulation effect. Do not use Harmonist or Octave.
2. Set the MODULATION Controls knobs to an appropriate setting.
(Not suggested settings. For illustration only)
3. Press the MOD PEDAL to turn on the Modulation effect.
4. Play some chords or leads.
STEP THREE: Add Delay 1. Turn the DELAY TYPE knob to select ANALOG.
2. Set the DELAY Control knobs to an appropriate setting.
3. Press the DELAY PEDAL.
4. Play some chords or leads. 5. Hold the DELAY PEDAL down for two seconds. 6. Tap in a different delay time with the DELAY PEDAL. NOTE: You can also change the rate of the Modulation effect by repeating this procedure with the MOD PEDAL.
STEP FOUR: Add PEDAL FX 1. Turn the EXPRESSION knob to select WAH.
2. Press the toe end of the EXPRESSION PEDAL hard to turn on the WAH. The PEDAL FX LED will light. 3. Play some chords or leads using the WAH.
STEP FIVE: Show the Phrase Looper NOTE: When using the Phrase Looper, use the DELAY PEDAL to control all recording, playback, and overdub functions. 1. Set the DELAY TYPE knob to PHRASE LOOP.
2. Use the NUMBERED (FX PEDALS) to turn on/off effects needed for a clean sound. 3. When you are ready to record, press the DELAY PEDAL.
4. When youre finished with the first loop, press the DELAY PEDAL. The Phrase will play back. NOTE: Make sure you do this on the beat. 5. Change the guitars tone using the NUMBERED (FX) PEDALS. 6. Press the DELAY PEDAL again to overdub another track onto the existing loop. 7. If desired, repeat steps 4-6. 8. When you are finished, press the DELAY PEDAL twice to stop the looper.

NOTES:

3. GOING DEEP
How to Switch to Memory Mode 1. Press the MOD and DELAY PEDALS down simultaneously. The BANK number will appear in the LED display. 2. Press both pedals down again or press EXIT to return to Manual Mode. The MANUAL MODE LED will light to confirm Manual Mode. How to Change Programs in Memory Mode 1. Press the left or right NS/ THRES/BANK BUTTONS to select a BANK. 2. Press PEDAL ONE, TWO or THREE to select a patch within the BANK. Or 1. Press the COMP and OD/DS PEDALS simultaneously to engage BANK SELECT. 2. Press PEDAL ONE or PEDAL TWO as needed to select the BANK. 3. Press PEDAL THREE or PEDAL FOUR to confirm the selection. 4. Press PEDAL ONE, TWO, THREE OR FOUR to select a patch within the BANK. How to Edit a Program 1. Use the above procedures to select a patch in a USER BANK. 2. Press EDIT. 3. Adjust the settings of the knobs and pedals. NOTE: you must move the knobs past their current stored settings to enable the new settings. 3. Press WRITE twice. How to Use the Tuner 1. Press the OD/DS and MOD PEDALS down simultaneously. 2. Tune up. The note played will show in the Display. The red LEDs in the display will indicate whether the note is sharp, flat, or in tune. 3. Press the OD/DS and MOD PEDALS again or press EXIT to return to play mode.
How to Use EZ TONE EZ-TONE is a set of preset effects. Each effect in the ME-70 comes with an optimized pre-made setting. These are useful for quick patch setups when you want to get a good sound without having to dial in every parameter of ever effect. 1. Press EZ TONE. 2. Turn a TYPE KNOB to select the EZ-TONE for that effect. Each EZ-Tone is numbered. How to Write Your Own EZ-TONES Use the above procedures to select an EZ-TONE. Turn the effects KNOBS to dial in the settings. While holding down the EZ-TONE BUTTON, press WRITE. Press the left or right NS THRES/BACK BUTTONS to select the effect you want to save. 5. Press WRITE again. How to Re-Initialize the ME-70 1. Set the ME-70 to Manual Mode. 2. While holding down the EDIT/EXIT BUTTON, press the MOD PEDAL. An F (factory reset) will appear in the display. 3. Press WRITE twice. 1. 2. 3. 4.
4. FIVE THINGS TO KNOW and SHOW
1. Easiest to use BOSS multi-effect. Just turn the knobs! 2. COSM modeled Amps, OD/DS, Modulations, and Delays 3. Tap tempo both Mod and Delay 4. Tough metal case 5. Battery or AC operation-use it any time, anywhere

5. ACCESSORIES

1. BOSS PSA-120 AC Adapter 2. Two BOSS FS-5U Footswitches or one BOSS FS-6 3. Roland PCS-31L TRS-2 x 1/4 insertion cable 4. BOSS Bag-S2 Carrying bag 5. Roland RH-5, RH-200 or other headphones 6. Instrument cables

6. ME-70 EFFECTS

PREAMP 1. CLEAN 2. COMBO 3. TWEED 4. STACK 5. LEAD STACK 6. R-FIER 7. 4-Band EQ COMP/FX 1. COMPRESSOR 2. T-WAH UP 3. T-WAH DOWN 4. SLOW GEAR 5. DEFREETER 6. Single>Hum (Pickup Simulator) 7. Hum>Single (Pickup Simulator) 8. SOLO COSM OVERDRIVE/DISTORTION 1. BOOST 2. NATURAL 3. OD-1 4. BLUES 5. DIST 6. CLASSIC 7. MODERN 8. METAL 9. CORE 10. FUZZ MODULATION 1. CHORUS 2. PHASER 3. FLANGER 4. ROTARY 5. UNI-V 6. TREMOLO 7. VIBRATO 8. HARMONIST 9. OCTAVE 10. DELAY

DELAY 1. 1-99ms 2. 100-999 ms 3. 1000-6000ms 4. ANALOG 5. MODULATE 6. REVERSE 7. CHO+DELAY 8. MOMENTARY 9. TAP 10. PHRASE LOOPER PEDAL EFFECTS 1. WAH 2. VOICE 3. +1 OCTAVE 4. 1 OCTAVE 5. MOD RATE 6. DELAY LEVEL NS (NOISE SUPPRESSOR) REVERB 1. ROOM 2. HALL