You Are Responsible For Firearms Safety As a gun owner, you accept a set of demanding responsibilities. How seriously you take these responsibilities can mean the difference between life and death. Failure to follow any of these instructions can cause extensive damage to your gun and/or possible serious injury or death to yourself and others. There is no excuse for careless or abusive handling of any firearm. At all times handle any firearm with intense respect for its power and potential danger.
PLEASE READ AND UNDERSTAND ALL OF THE CAUTIONS, PROPER HANDLING PROCEDURES AND INSTRUCTIONS OUTLINED IN THE OWNERS MANUAL BEFORE USING YOUR NEW FIREARM.
1. ALWAYS KEEP THE MUZZLE OF YOUR RIFLE POINTED IN A SAFE DIRECTION, even though you are certain that the rifle is unloaded. Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within the range of your ammunition. 2. NEVER RELY TOTALLY ON YOUR RIFLE'S MECHANICAL "SAFETY" DEVICE. The word "safety" describes a gun's trigger block mechanism, sear block mechanism, hammer block mechanism or firing pin block mechanism. These mechanical devices are designed to place your gun in a SAFER status. No guarantee can be made that the gun will not fire even if the "safety" is in the "on safe" position. See "Operations of the Safety" for instructions on operation of YOUR gun's "safety."
LIKE ANY MECHANICAL DEVICE, A "SAFETY" CAN SOMETIMES FAIL; IT CAN BE JARRED OR INADVERTENTLY MANIPULATED INTO AN UNSAFE CONDITION.
Mechanical "safeties" merely aid safe gun handling and are no excuse for pointing your rifle's muzzle in an unsafe direction. While it is a good idea to "test" your rifle's mechanical "safeties" periodically for proper function, NEVER TEST IT WHILE YOUR RIFLE IS LOADED OR POINTED IN AN UNSAFE

DIRECTION

Safe gun handling does not stop with your gun's mechanical "safety devices -- it starts there. Always treat your rifle with the respect due a loaded, ready-to-fire firearm. 3. WHENEVER YOU HANDLE A FIREARM, OR HAND IT TO SOMEONE, ALWAYS OPEN THE
ACTION IMMEDIATELY, VISUALLY CHECK YOUR RIFLE'S CHAMBER, FEED MECHANISM AND MAGAZINE.
Make certain they do not inadvertently contain any ammunition. Always keep the chamber empty and "safety" in the "on safe" position unless shooting is imminent. 4. DO NOT TRANSPORT YOUR RIFLE LOADED, WHETHER IN A SCABBARD, GUN CASE, OR

OTHER CONTAINER.

5. HUNTING FROM ELEVATED SURFACES SUCH AS TREE STANDS IS DANGEROUS, and may increase the risk of handling a firearm. The following rules should always be observed by you and those you hunt with: Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up to and down from the stand. Always make certain that your firearm is not dropped from the stand, or dropped while it is being taken up to or down from the stand. Remember, a loaded firearm may discharge when dropped, even with the safety in the "on safe" position.
6. BEWARE OF BARREL OBSTRUCTIONS, for the safety of both your gun and yourself. Mud, snow, and an infinite variety of other obstructions may inadvertently lodge in a barrel bore. It takes only one small obstruction to cause dangerously increased pressures that can ruin (swell or rupture) the finest rifle barrels.
BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN NO LIVE ROUND IS IN THE CHAMBER AND THAT THE MAGAZINE IS REMOVED AND FEED MECHANISMS ARE COMPLETELY EMPTY. PLACE THE "SAFETY" IN THE "ON SAFE" POSITION.

Look through the barrel to be sure it is clear of any obstruction. If an obstruction is seen, no matter how small it may be, clean the bore with a cleaning rod and patch as described in "Cleaning and Maintenance Suggestions." Before the first firing, clean the bore with a cleaning rod and patch, and wipe away any anti-rust compound in the action/chamber areas. 7. ALWAYS UNLOAD YOUR RIFLE WHEN NOT IN USE. REFER TO "UNLOADING THE RIFLE"
FOR AN EXPLANATION OF HOW TO UNLOAD YOUR RIFLE PROPERLY.
As a safety precaution, it is preferable to disassemble your gun for storage. Store your gun and ammunition separately -- well beyond the reach of children. Take all safeguards to ensure your rifle does not become available to untrained, inexperienced or unwelcome hands. 8. USE THE PROPER AMMUNITION. The barrel and action of this rifle have been made with substantial safety margins over the pressures developed by established American commercial loads. Nevertheless, Browning assumes no liability for incidents which occur through the use of cartridges of nonstandard dimensions which develop pressures in excess of commercially available ammunition with standards established by the Sporting Arms and Ammunitions Manufacturers' Institute (SAAMI).
BE ALERT TO THE SIGNS OF AMMUNITION MALFUNCTION.
If you detect an off sound or light recoil when a cartridge s fired, DO NOT LOAD ANOTHER CARTRIDGE INTO THE CHAMBER. Open the action and remove all cartridges from the magazine, chamber and action areas. With the action open, glance down the barrel to make sure that an obstruction does not remain in the barrel. If there is an obstruction, completely clear the barrel before loading and firing again. Failure to follow these instructions can cause extensive damage to your gun and possible serious injury to yourself and others.
MAKE SURE OF ADEQUATE VENTILATION IN THE AREA THAT YOU DISCHARGE A FIREARM. WASH HANDS THOROUGHLY AFTER EXPOSURE TO AMMUNITION OR CLEANING A FIREARM.
Lead exposure can be obtained from discharging firearms in poorly ventilated areas, cleaning firearms or handling ammunition. Lead is a substance that has been known to cause birth defects, reproductive harm and other serious injury. 9. DO NOT SNAP THE FIRING PIN ON AN EMPTY CHAMBER -- THE CHAMBER MAY NOT BE

EMPTY!

Treat every gun with the respect due a loaded gun, even though you are certain the gun is unloaded. 10. KEEP FINGERS AWAY FROM THE TRIGGER WHILE UNLOADING, LOADING, UNTIL YOU

ARE READY TO SHOOT.

11. BE SURE OF YOUR TARGET AND BACKSTOP. Particularly during low light periods. Know the range of your ammunition. Never shoot at water or hard object. 12. ALWAYS UNLOAD YOUR RIFLE'S CHAMBER BEFORE CROSSING A FENCE, CLIMBING A
TREE, JUMPING A DITCH OR NEGOTIATING OTHER OBSTACLES.

Refer to "Unloading The Rifle" for instructions on the unloading of your rifle. Never place your loaded rifle on or against a fence, tree, car or other similar object. 13. WEAR EYE AND EAR PROTECTION WHEN SHOOTING. Unprotected, repeated exposure to gunfire can cause hearing damage. Wear ear protectors (shooting ear plugs or muffs) to guard against such damage. Wear shooting glasses to protect your eyes from flying particles. Allow proper distance (eye relief) between the scope and your eye when firing a scoped rifle or shotgun. Always keep a safe distance between the muzzle of your firearm and any persons nearby, as muzzle blast, debris and ejecting shells could inflict serious injury. Also, wear eye protection when disassembling and cleaning your shotgun to prevent the possibility of springs, spring-tensioned parts, solvent or other agents from contacting your eyes. 14. DROPPING A LOADED GUN CAN CAUSE AN ACCIDENTAL DISCHARGE even with the "safety" in the "on safe" position. Be extremely careful while hunting or during any shooting activity, to avoid dropping any firearm. 15. IF YOUR RIFLE FAILS TO FIRE, KEEP THE MUZZLE POINTED IN A SAFE DIRECTION. Hold this position for a minimum of 30 seconds. Carefully open the action and remove the cartridge. If the primer is indented, the cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction should be corrected before further use. 16. BE DEFENSIVE AND ON GUARD AGAINST UNSAFE GUN HANDLING AROUND YOU AND

OTHERS.

Don't be timid when it comes to gun safety. If you observe other shooters violating any of these safety precautions, politely suggest safer handling practices. 17. BE CERTAIN YOUR RIFLE IS UNLOADED BEFORE CLEANING. Because so many gun accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your gun is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 18. TEACH AND SUPERVISE FIREARMS SAFETY TO ALL MEMBERS OF YOUR FAMILY -ESPECIALLY TO CHILDREN AND NONSHOOTERS.
Closely supervise newcomers to the shooting sports. Encourage enrolling in hunting/shooting safety courses. 19. NEVER DRINK ALCOHOLIC BEVERAGES OR TAKE ANY TYPE OF DRUGS BEFORE OR

DURING SHOOTING.

Your vision and judgment could be dangerously impaired, making your gun handling unsafe to you and to others.
20. READ AND HEED ALL WARNINGS in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-to-date information on the safe handling procedures of your Browning gun. Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combinations are used. 21. PERIODIC MAINTENANCE -- AVOID UNAUTHORIZED SERVICING. Your rifle is a mechanical device which will not last forever, and as such, is subject to wear and requires periodic inspection, adjustment and service. Browning firearms should be serviced by a Browning Recommended Service Center or by Browning's service facility in Arnold, Missouri. Browning cannot assume any responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifications of Browning firearms. 22. BROWNING RESERVES THE RIGHT TO REFUSE SERVICE ON FIREARMS THAT HAVE

BEEN ALTERED, ADDED TO OR SUBSTANTIALLY CHANGED.
Removal of metal from barrel(s), or modification of the firing mechanism and/or operating parts may lead to Browning's refusal of service on such firearms. Browning will charge the owner parts and labor to return the firearm to original Browning specifications.
DO NOT, UNDER ANY CIRCUMSTANCES, ALTER THE TRIGGER, SAFETY OR PARTS OF THE FIRING MECHANISM OF THIS OR ANY OTHER FIREARM. FAILURE TO OBEY THIS WARNING MAY RESULT IN INJURY OR DEATH TO YOURSELF OR OTHERS.

BE CAREFUL!

for service or cleaning is required. take your gun to a Browning recommended Service Center or a competent gunsmith, or send it to our Arnold, Missouri Service Facility as explained under Service or Repair". Cleaning the magazine Depending on how often you shoot. it is helpful to disassemble the box magazine for cleaning. First, remove the detachable box magazine from the rifle. Slide the magazine bottom plate out to the rear. The magazine spring and follower can then be easily removed for inspection. Wipe off any dirt or residue then apply a very thin coat of oil and wipe clean again. Too much oil will only serve to collect oil and dirt. TO reassemble. reinsert the spring and follower, then slide the bottom plate back into position (See figure 14).

Disassembly

NEVER ATTEMPT TO TAKE YOUR A-BOLT APART FURTHER THAN EXPLAINED IN THIS MANUAL.
This is a specialized, finely fitted mechanism, You may permanently mar it by attempting to disassemble the inner mechanism assemblies. If further disassembly

Service

or Repair
If your firearm should require service or repairs, we suggest you first contact a local recommended Browning Firearms Service Center. Contact your Browning sporting goods dealer or call our Service Department for the address of the Service Center nearest you. Otherwise, you may send your firearm directly to our own Service Department. For technical questions about your firearm or service call our Service Department.
Browning Service Department 3005 Arnold Tenbrook Road Arnold, Missouri 63010-9406 Phone: 1-800-322-4626

When YOU a. b.

returning your firearm for servicing, must do the following: Be sure it is completely unloaded. Package it securely in a cardboard container. c. Enclose a letter with your firearm that clearly describes the trouble experienced and the repairs or alterations desired. d. If convenient, send a copy of the letter to us separately. e. Never return ammunition with your firearm. It is against postal and most commerce regulations.

Canadian Customers call or write:
Browning Canada Sports Ltd./Ltee, 5617 Chemin St-Francois St-Laurent, Quebec H4S 1W6 Phone: (574) 333-7267
If you have any questions about this manual or about any other Browning products, call or write our Consumer Information Department:
Browning Consumer Morgan, Utah 84050 Phone: (801) 876-2711 Information
times. Caution should be exercised to ensure that the cleaning rod or handle does not strike the crown of the muzzles, as damage to this area can affect the accuracy of the rifle. 3 INSPECT THE CHAMBER AND BORE FOR POWDER FOULING. A normal amount of powder residue can be expected and is not serious. It can usually be removed by repeating step No. 2, using a patch saturated with nitro solvent. If or when fouling should become heavy, it can be removed with a brass bore brush. Dip or spray the brush with nitro solvent and scrub the chamber and bore until the fouling is removed. To prevent brass bristles from breaking off, the brush should be pushed completely through the bore before being withdrawn. 4 AFTER FOULING HAS BEEN REMOVED, THE BORE SHOULD BE WIPED DRY. Then pass a slightly oiled patch through the bore, for preservation. A fine, light gun oil like Browning Oil is recommended. 5 THE INTERIOR OF THE RECEIVER AND THE
2 The trigger pull adjustment screw is located at the rear of the trigger assembly (See figure 13). To decrease the weight of the trigger pull, turn the adjustment screw in a clockwise direction using a small screw driver. To increase the trigger pull, turn the adjustment screw in a counter clockwise direction. NOTE: If trigger pull is increased too much, the trigger cannot be pulled. Turn the screw clockwise until trigger can be pulled.
3 Trigger pull can be measured, with the bolt closed, using a very accurate spring scale or a commercially available set of trigger pull measuring weights. Most gunsmiths can also measure trigger pull for you. 4 When finished making the adjustment, place the trigger guard back in the stock and reinstall the trigger guard screw snugly. Swivels The Browning A-Bolt Medallion is equipped with swivel studs and swivels. Other A-Bolt models are equipped with swivel studs only. Cleaning and Maintenance The correct procedure for cleaning your A-Bolt is as follows: 1 BE CERTAIN THE RIFLE IS UNLOADED AND THE

BOLT HAS BEEN REMOVED.

BOLT SHOULD PERIODICALLY BE WIPED OFF WITH A CLEAN RAG. Remove the bolt occasionally and wipe clean. Any dried oil in the receiver area should also be removed. Follow this cleaning with a very light film of oil on working parts. Do not pour large quantities of oil into the action. An excess of oil will run into the wood and cause it to soften or warp.
WIPE ALL EXPOSED METAL SURFACES WITH AN OILED CLOTH MAKING SURE TO WIPE THE
Finger marks should be removed because they provide a place where moisture can accumulate. Ordinary good judgment will, of course, indicate that the metal of the gun should receive a light film of oil any time the rifle has been exposed to weather or handling.

NOTE: IF THE BOLT IS IN CLOSED POSITION, BE SURE THE SAFETY IS IN THE ON SAFE POSITION. Hold the rifle with either hand at the forearm. Depress the magazine latch in front of the trigger guard with the index finger of your free hand and allow the hinged floorplate-magazine unit to swing downward (See figure 7).

LOADING

MAGAZINE
TACHED FROM THE FLOORPLATE PLACE THE RIFLES SAFETY IN THE ON SAFE POSITION. BE SURE THE MUZZLE IS POINTED IN A
Lay a round on top of the follower and press down with your thumb until it is retained in the magazine. Care should be exercised in positioning each cartridge so that its base is flush with the rear of the magazine. If the nose of a cartridge protrudes beyond the front of the magazine, it could cause feeding problems or interfere with the closing of the magazine floorplate (See figure 8). After loading the magazine, swing the floorplate upwards until it is retained by the magazine latch. The bolt may be cycled at any time you wish to load the chamber. Slide the thumb safety to the rear to
PLACE THE LOADED RIFLE IN ON SAFE STATUS. The magazine- floorplate unit may be opened at any time to refill the magazine to capacity.
With the magazine-floorplate unit open, the magazine may be detached by merely pulling it away from the hinged floorplate. Grasp the sides of the magazine, toward the front, then pull the magazine away from the floorplate (See figure 9).

SAFE DIRECTION.

The rifle may be supported in its barrel down position during this procedure with the opposite hand at the forearm. Once the magazine has been detached, it may be reloaded with cartridges as described under Loading with the magazine attached to the floorplate. To reattach, insert the small lip on the rear face of the magazine into the matching groove in the back end of the floorplate (See figure 10). Then snap the front of the magazine firmly into place. Extra magazines may be carried loaded for rapid replacement of an empty magazine, using this same procedure. After loading the magazine, swing it up into place until it is retained by the magazine latch.

KEY # 31 31

PART NO. PO78578 *PO78A80 *PO78093 PO78094 PO78096 PO78596 PO78099 PO78102 PO78106 PO78506 PO78610 POPO78615 PO78616 *PO78618 PO78622 PO78626 PO78625 PO78629 *PO78591 *PO78592 PO78593 PO78A91 PO78A40 PO78A41 PO78154 PO78156 PO78153

Browning

DESCRIPTION

A-Bolt

KEY # 45 45
PART NO. PO78162 PO78166 PO78169 PO78962 PO78663 PO78963 PO78173 PO78673 PO78184 PO78188 PO78685 PO78185 PO78178 PO76181 PO78679 PO78176 PO78180 PO78179 PO78177 PO78175 PO78183 PO78166 PO78944 PO78945

DESCRIPTION Magazine Follower 25-06, 30-06, 270W, 280R Magazine Follower 7MM, 300W, 338W Mag Magazine Follower.375 H&H Mag. Magazine Follower 284W Micro Medallion Magazine Follower 223R Short Magazine Follower 223R Micro Medallion Magazine Follower Spring Magazine Follower Spring,.223R Magazine Ramp Rivet, Long Action Magazine Ramp Rivet 375 H&H, 284W Magazine Ramp Rivet.223 Magazine Ramp Rivet, Short Action Magazine Ramp 22-250 Magazine Ramp 243,308,7MM-08 Magazine Ramp.223 Magazine Ramp 25-06,30-06, 270W, 280R, 338W Magazine Ramp 300W Mag. Magazine Ramp 7MMR Mag. Magazine Ramp.338W Mag. Hunter Magazine Ramp.284W Magazine Ramp.375 H&H Magazine Ramp.257R Magazine Ramp 223R Micro Medallion Magazine Ramp 284W Micro Medallion 77 *PO78APO78294 PO78298 PO78299 PO78296 *PO78805 *PO7805L *PO78806 *PO78802 *PO7802L *'PO78801 *PO78804 *PO78807 *PO78AKEY # PART NO. *PO78764 *PO78A64 *PO78268 PO78772 *PO78275 *PO78282 *PO78286 *PO78290 PO78814 PO78895 PO78297 DESCRlPTlON Safety Selector, Medallion Safety Selector, Stainless Stalker Safety Spring Safety Stud Sear Sear Pin Sear Screw Sear Spring Scope Mount filler screws Sling Eyelet Assy. Front Sight Assembly Rear, Williams Type, Long Action Sight Assembly Rear, Williams Type, Short Action Sight Front, Williams Type Sight Ramp, Williams Type Sight Swivel Eyelet Rear Stock Long Action Mag., Medallion Stock Long Action Mag., Medallion L.H. Stock Long Action Mag., Hunter Stock Long Action Std., Medallion Stock Long Action Std., Medallion L.H Stock Long Action Std., Hunter Stock Long Action,.375 H&H Stock Long Action, L. H. 375 H&H Stock Composite, R.H. Std. & Mag. Stainless Stalker StockComposite, L. H. Std. &Mag. Stainless Stalker
Bolt Shroud, Medallion Bolt Shroud, Stainless Stalker But Plate But Plate Screws Ejector Ejector, 223R Ejector Pin Ejector Spring Extractor Extractor, 223R Extractor Spring Extractor Spring, 223R Firing Pin Long Action Firing Pin, Short Action Firing Pin Sear Firing Pin Sear Pin Firing Pin Spring, Long Action Firing Pin Spring, Short Action Firing Pin Washer Gas Stop Assembly, Long Action Gas Stop Assembly, Short Action Gas Stop Assembly, 223R Micro Medallion Gas Stop, Stainless Stalker Grip Cap Composite Stalker Grip Cap Screw Composite Stalker Magazine Base, Long Action Magazine Base, Short Action Magazine Base. 375 H &H Mag.
PO78956 PO78957 PO78158 PO78159 PO78157 PO78659 PO78A12 PO78714 PO78712 PO78215 PO78218 PO78222 PO78A22 PO78227 PO78229 PO78A08 PO78715 PO78716
Magazine Base, 223R Micro Medallion Magazine Base, 284W Micro Medallion Magazine Body, Long Action Magazine Body, Short Action Magazine Body 375 H&H Mag. Magazine Body w/insert.223R Magazine Floorplate Hinge, Stainless Stalker Magazine Floor Plate Hinge, Hunter Magazine Floor Plate Hinge, Medallion Magazine Floor Plate Hinge Pin Magazine Floor Plate Hinge Spring Magazine Floor Plate Latch Assembly Magazine Floor Plate Latch Assem , Stainless Stalker. Magazine Floor Plate Latch Pin Magazine Floor Plate Latch Spring Magazine Floorplate, Stainless Stalker Magazine Floor Plate 1990 Type, Long Action Medallion Magazine Floor Plate 1990 Type, Long Action Hunter

PO78946 PO78947 PO78233 PO78234 PO78198 PO78698 PO78187 PO78687 PO78202 PO78192 PO78692 PO78201 PO78701 PO78204 *PO78739 *PO78738 *PO78A38 PO78248 PO78252 PO78358 *PO78240 *PO78765 *PO78770 *PO78771 *PO78773 *PO78255 *PO78756 *PO78258 *PO78261 *PO78766
Magazine Ramp 22-250 Micro Medallion Magazine Ramp 243, 308, 7mm-08, 257R Micro Medallion Magazine Retainer Spring New Style Magazine Retainer Spring Pin Magazine Spring Pin Magazine Spring Pin.223R Magazine Spring Strut Inner Magazine Spring Strut Inner,.223R Magazine Spring Strut Inner,.375 H&H Magazine Spring Strut Outer Magazine Spring Strut Outer,.223R Magazine Strut Pin Magazine Strut Pin,.223R Magazine Strut Spring Mechanism Housing, Hunter Mechanism Housing, Medallion Mechanism Housing, Stainless Stalker Mechanism Housing Screw Mechanism Housing Screw Washer Mechanism Housing Set Pin Safety Safety Blocking Pin Safely Lever Safety Lever Pin Safely Lever Spring Safety Link Safety Link Roll Pin Safety Pin Safety Pln Snap Ring Safety Selector, Hunter
*PO78808 *PO78803 *PO78903 *PO78816 *PO78A16 *PO78916 *PO78A76 *PO78876 PO78821 PO78820 PO78920 PO78A20 PO78326 PO78A26 PO78926 *PO78829 *PO78834 *PO78845 *PO78866
Stock Short Action, Hunter Stock Short Action, Medallion Stock Micro Medallion Trigger A-Bolt Trigger, Stainless Stalker Trigger, Micro Medallion Trigger Assembly, Stainless Stalker Trigger Assembly Trigger Guard, Hunter Trigger Guard, Medallion Trigger Guard, Micro Medallion Trigger Guard, Stainless Stalker Trigger Guard Screw Trigger Guard Screw, Stainless Stalker Trigger Guard Screw, Micro Medallion Trigger Pin Trigger Pull Adjusting Screw Trigger Sear Trigger Spring
'Indicates part must be fitted by Browning Service Department or qualified gunsmith. Part may be purchased only by holders of current, valid Federal firearms License. When ordering parts do not order using key numbers.
PO78720 PO78717 PO78721 PO78170 PO78163 PO78164
Magazine Floor Plate 1990 Type, Short Action Medallion Magazine Floor Plate 1990 Type, Short Action Hunter Magazine Floor Plate 1990 Type, Stainless Stalker Magazine Follower Rivet Magazine Follower, Short Action 22-250 Magazine Follower, Short 243, 308, 257R, 7MM-08, 284W

KEY # 03 03

PART NO. PO78526 PO78525 PO78A25 PO78528 PO78529 PO78929 PO78A29 *PO78923 *PO78523 *PO78524 *PO78508 *PO78507 *PO78907 *PO78487 *PO78505 *PO78504
PART NO. *PO78512 *PO78511 *PO78911 *PO78522 *PO78521 *PO78489 *PO78496 *PO78A14 *PO78501 *PO78500 *PO78900 *PO78520 *PO78519 *PO78919 *PO78516 *PO78515 *PO7815L *PO78A17 *PO78495

*PO78518 *PO78517 *PO78917 *PO78514 *PO78A13
Barrel/Receiver 7MM-08, Hunter Barrel/Receiver 7MM-08, Medallion Barrel/Receiver 7MM-08, Micro Medallion Barrel/Receiver 7MMR Mag, Hunter Barrel/Receiver 7MMR Mag, Stainless Stalker
*PO78073 *PO78536 *PO7836L *PO78044 *PO7844L *PO78074
Boll Handle, L.H. Stainless Stalker Bolt Handle, Medallion Bolt Handle, Med. L.H. Bolt Handle Lock Bolt Handle Lock L.H. Bolt Handle Lock L.H. Slainless Stalker
*PO78513 *PO7813L *PO78494 *PO78A23 *PO78497 *PO78013 *PO78527 *PO78537 *PO78539 *PO78540 *PO78541 *PO78542 *PO78543 *PO78544
Barrel/Receiver 7MMR Mag, Medallion Barrel/Receiver 7MMR Mag, L.H. Medallion Barrel/Receiver 7MMR Mag, L.H. Stainless Stalker Barrel/Receiver 375 H&H Stainless Stalker Barrel/Receiver 375 H&H, L.H. Stainless Stalker Barrel/Receiver 375 H&H, Medallion Barrel/Receiver 375 H&H, L.H. Medallion Bolt Assembly, 22-250 Micro Medallion & Medallion Bolt Assembly, 22-250 Hunter Bolt Assembly,.223R Micro Medallion & Medallion Bolt Assembly,.223R Hunter Bolt Assembly,.243W-284W Micro Medallion & Medallion Bolt Assembly,.243W-284W Hunter Bolt Assembly, 7MMR, 300W, 338W, 375 H&H Medallion
PO78046 Bolt Handle Pin *PO78549 Bolt Head *PO78546 Bolt Head 223 *PO78548 *PO78550 *PO78552 *PO7850L *PO7852L *PO78558 PO78562 PO78560 PO7860L *PO78A62 PO78063 PO78565 PO78568 PO78072 PO78076 PO78580 Bolt Head 22-250

.243W-284W

Bolt Head 308W, 7MM-08,257R, 30-06,25-06,270W, 280R Bolt Head 7MM R, 300W, 338W, 375 H &H Mag. Bolt Head.270W, 30-06,25-06, 280R L.H. Bolt Head 7MM R, 300W, 338W, 375 H&H Mag. L.H. Bolt Head Key Pin Bolt Retainer, Hunter Bolt Retainer, Medallion Bolt Retainer Med. L.H. Bolt Retainer, Stainless Stalker Bolt Retainer L.H. Stainless Stalker Bolt Retainer Guide Pin Bolt Retainer Pin Bolt Retainer Screw Bolt Retainer Spring Bolt Shroud, Hunter
THE BROWNING A-BOLT RIFLE Schematic is provided for parts identification only and should not be used as a guide to assemble the rifle.
IMPORTANT: When ordering parts, list code number, part name, caliber, model and serial number. (Do not order parts using key numbers.) CAUTION: Browning parts are made exclusively for Browning guns and should not be used in other guns even though models may be similar. Inadequately fitted parts may be dangerous.
aligned with the bottom bolt lug (See figure 3). Push the bolt completely forward and rotate the handle down to lock it (See figure 4). It is not necessary to depress the bolt stop to insert the bolt. RETURN THE THUMB-OPERATED SAFETY TO THE ON SAFE POSITION. The rifle is now completely assembled and may be operated normally.
DO NOT DEPEND ON THE RED COLOR ALONE TO INDICATE YOUR GUNS SAFETY STATUS.
red. When the rifle is cocked it may be readily felt with the thumb as well as easily seen with a quick glance downward (See figure 6). When the rifle is fired, the cocking indicator retracts into the bolt shroud and cannot be seen or felt. Loading the rifle The Browning A-Bolt utilizes a unique detachable box magazine with a hinged floorplate. The magazine on standard calibers holds four rounds. On magnum calibers, the Micro Medallion and 284 Win., the capacity is three rounds. Under certain conditions it may be possible to load an extra round into the magazine of the Micro Medallion, however, this practice may alter the function of your firearm. With an extra round in the magazine and the bolt closed. it may not be possible to latch the magazine floorplate.

BEFORE THE FIRST FIRING, CLEAN THE ANTI-RUST COMPOUND from the inside of the receiver with a clean rag and light gun oil. Browning Oil is ideal for removing this compound and for giving your new gun its first lubrication. However, any quality gun oil may be used. For an explanation of cleaning procedures see Care and Cleaning on page 12.
Operation of the Safety The safety is located on the top tang at the rear of the receiver. When the safety is drawn with the thumb to the rear, the gun is in the on safe position. This blocks the trigger and locks the bolt in the closed position. In this position an S will appear on the tang in front of the safety. WHENEVER A
CARTRIDGE IS CHAMBERED, THE RIFLE SHOULD BE KEPT IN THE ON SAFE POSlTlON UNTIL YOU ARE READY TO FIRE IT. When the safety is pushed forward, the S will be covered and a red dot on the stock will appear indicating that the rifle is in the off safe position and ready to fire (See figure 2).
Inserting and removing the bolt 1 INSERTING THE BOLT The A-Bolt rifle comes packed in a foam-padded box with the bolt removed from the rifle. It is necessary to insert the bolt into the receiver. To do this, first place the safety in the off safe position. Align the forward end of the bolt in the rear opening of the receiver. Be sure the cartridge depressor is also
Hold this position for a minimum of 30 seconds. Carefully open the action and remove the cartridge. If the primer is indented, the cartridge should be disposed of in a way that cannot cause harm. If the primer is not indented, your firearm should be examined by a qualified gunsmith and the cause of the malfunction should be corrected before further use. 16 BE DEFENSIVE AND ON GUARD AGAINST
UNSAFE GUN HANDLING AROUND YOU AND OTHERS.
19 NEVER DRINK ALCOHOLIC BEVERAGES OR
TAKE ANY TYPE OF DRUGS BEFORE OR DURING SHOOTING.
Your vision and judgment could be dangerously impaired, making your gun handling unsafe to you and to others. 20 READ AND HEED ALL WARNINGS in this instruction book, on ammunition boxes and with all accessories that you install on your firearm. It is your responsibility to secure the most up-todate information on the safe handling procedures for your Browning gun. Browning assumes no liability for incidents which occur when unsafe or improper gun accessories or ammunition combinations are used. 21 PERIODIC MAINTENANCE AVOID UNAUTHORIZED SERVICING.
Dont be timid when it comes to gun safety. If you observe other shooters violating any of these safety precautions, politely suggest safer handling practices. 17 BE CERTAIN YOUR RIFLE IS UNLOADED BEFORE CLEANING. Because so many gun accidents occur when a firearm is being cleaned, special and extreme care should be taken to be sure your gun is unloaded before disassembly, cleaning and reassembly. Keep ammunition away from the cleaning location. Never test the mechanical function of any firearm with live ammunition. 18 TEACH AND SUPERVlSE FlREARMS SAFETY TO

ALL MEMBERS OF YOUR FAMILY ESPECIALLY TO CHILDREN AND NONSHOOTERS.
Your rifle is a mechanical device which will not last forever, and as such, is subject to wear and requires periodic inspection, adjustment, and service. Browning firearms should be serviced by a Browning Recommended Service Center or by Brownings service facility in Arnold, Missouri. Browning cannot assume any responsibility for injuries suffered or caused by unauthorized servicing, alterations or modifications of Browning firearms.
Closely supervise newcomers to the shooting sports. Encourage enrollment in hunting/shooting safety courses.

Nomenclature

In conventional gun terminology the position and movement of gun parts are described as they occur with the gun horizontal and in normal firing posi-
tion; i.e., the muzzle is forward or front; the butt stock is rearward or rear; the trigger is downward or underneath; the sights are upward or on top. For general nomenclature refer to Figure 1.
(See page 11 for instructions on unloading). After assuring yourself that the rifle is completely empty, again, open the bolt and remove it from the receiver (as described in Removing the Bolt on page 6). Look through the barrel to he sure it is clear of any obstruction. If an obstruction is seen, no matter how small it may be, clean the bore with a cleaning rod and patch as described in Cleaning and Maintenance Suggestions on page 12. Before the first firing, clean the bore with a cleaning rod and patch, and wipe away any anti-rust compounds in the action/chamber areas. 7 ALWAYS UNLOAD YOUR RIFLE WHEN NOT IN
USE. REFER TO PAGE 11 OF THIS INSTRUCTlON BOOKLET EXPLAINING THE UNLOADING OF YOUR RIFLE.
fore loading and firing again. Failure to follow these instructions can cause extensive damage to your gun and possible serious injury to yourself and others., 9
DO NOT SNAP THE FIRING PIN ON AN EMPTY CHAMBER THE CHAMBER MAY NOT BE EMPTY!
Treat every gun with the respect due a loaded gun, even though you are certain the gun is unloaded. 10 KEEP YOUR FINGERS AWAY FROM THE
TRIGGER WHILE UNLOADING, LOADING, UNTIL YOU ARE READY TO SHOOT.
11 BE SURE OF YOUR TARGET AND BACKSTOP. Particularly during low light periods. Know the range of your ammunition. Never shoot at water or hard objects. 12 ALWAYS UNLOAD YOUR RIFLES CHAMBER
BEFORE CROSSING A FENCE, CLIMBING A TREE, JUMPING A DITCH OR NEGOTIATING OTHER OBSTACLES.
As a safety precaution, it is preferable to disassemble your gun for storage. Store your gun and ammunition separately-well beyond the reach of children. Take all safeguards to ensure your

WHENEVER YOU HANDLE A FIREARM, OR HAND IT TO SOMEONE, ALWAYS OPEN THE ACTION IMMEDIATELY, VISUALLY CHECK YOUR RIFLES CHAMBER, FEED MECHANISM AND MAGAZINE.
Make certain that they do not inadvertently contain any ammunition. Always keep the chamber empty and safety in the on safe position unless shooting is imminent. 4 DO NOT TRANSPORT YOUR RIFLE LOADED,
WHETHER IN A SCABBARD, GUN CASE, OR OTHER CONTAINER.
1 ALWAYS KEEP THE MUZZLE OF YOUR RIFLE POINTED IN A SAFE DIRECTION, even though you are certain the rifle is unloaded. Never point any firearm at anything you do not intend to shoot. Be extremely alert and aware of all persons and property within the range of your ammunition. 2 NEVER RELY TOTALLY ON YOUR RIFLES
MECHANICAL SAFETY DEVICE.
5 HUNTING FROM ELEVATED SURFACES SUCH
AS TREE STANDS IS DANGEROUS,
and may increase the risk of handling a firearm. The following rules should always be observed by you and those you hunt with: Always make certain that the stand being used is safe and stable. Always make certain that your firearm is unloaded when it is being taken up and down from the stand.Always make certain that your firearm is not dropped from the stand, or dropped while it is being taken up or down from the stand. Remember, a loaded firearm may discharge when dropped, even with the safety in the on safe position. 6
BEWARE OF BARREL OBSTRUCTIONS,
The word safety describes a guns trigger block mechanism, sear block mechanism, hammer block mechanism or firing pin block mechanism. These mechanical devices are designed to place your gun in a SAFER status. No guarantee can be made that the gun wi!l not fire even if the safety is in the on safe position. See Operation of the Safety on page 5 for instructions on operation of this guns safety.
LIKE ANY MECHANICAL DEVICE, A SAFETY CAN SOMETIMES FAIL; IT CAN BE JARRED OR INADVERTENTLY MANIPULATED INTO AN UNSAFE CONDITION.
for the safety of both your gun and yourself. Mud, snow, and an infinite variety of other objects may inadvertently lodge in a barrel bore. It takes only one small obstruction to cause dangerously increased pressures that can ruin (swell or rupture) the finest rifle barrels.
BEFORE CHECKING FOR A BARREL OBSTRUCTION, BE CERTAIN NO LlVE ROUND IS IN THE CHAMBER AND THAT THE MAGAZINE AND FEED MECHANISMS ARE COMPLETELY EMPTY. PLACE THE SAFETY IN THE ON SAFE POSITION
Mechanical safeties merely aid safe gun handling and are no excuse for pointing your rifles muzzle in an unsafe direction. While it is a good idea to test your rifles mechanical safeties periodically for proper function,

NEW GUN OWNERS RECORD

KEEP THIS RECORD FOR FUTURE REFERENCE