Model: 53-0021 Lit. #: 98-0579/04-05

Instruction Manual

INTRODUCTION The Bushnell Holosight XLP is based on advanced holographic technology. The Bushnell Holosight XLP enhances target acquisition, improves accuracy, and provides a high level of control within the shooting environment. This user manual describes the features of the Bushnell Holosight XLP and provides information on its use and maintenance. Please read the instructions carefully before mounting and using the sight and always practice proper rearm safety. Included: Assembled Holographic Diffraction Sight including mounting hardware 7/64 hex wrench (Weaver Base mount) 1/8 hex wrench (12 gauge model 1100, 870 or 1187 Remington or similar) BASIC OPERATION The Bushnell Holosight XLP uses a laser to create an illuminated hologram in the display window which appears as a virtual image of a reticle pattern. The reticle pattern appears to the user as a bright red image which is projected onto the target plane. No laser light is projected onto the target. Note that the Bushnell Holosight XLP has no magnication properties. Refer to Figure 1 for the user control or adjustment features locations. Refer to the MOUNTING section for installation instructions and correct placement on the gun.

FIGURE 1

BATTERIES Two (2) Type AAA alkaline 1.5 V batteries are required to operate the Bushnell Holosight XLP. The Bushnell Holosight XLP is designed to maintain constant brightness at a particular setting even as the batteries drain through normal use. The reticle brightness will not fade gradually as the batteries drain, but will shut down abruptly. The rst indication of the batteries draining is the reticle image blinking when the unit is turned on (see Electronic Features Section). Another indication of low batteries is the reticle image blinking off and on during recoil. With high recoil guns, this can occur before the battery check indicates low battery condition. If the reticle image blinks during recoil or turns off suddenly, replace the batteries. Read and follow the battery replacement and battery check procedures described in this Manual. Alkaline batteries are constructed differently by manufacturers. Tests show some brands are more susceptible to degradation by the shock of recoil. The use of Eveready Energizer batteries with the Bushnell Holosight XLP is recommended. INSTALLING OR REPLACING BATTERIES To remove the battery compartment cover, rotate the battery cover knurled screw counterclockwise and carefully pull the cover away from the sight housing (Figure 2). After the battery cover is removed, slide the batteries out and replace them with a fresh set. The plus and minus signs next to the battery insertion area indicates the correct

FIGURE 2

polarity of the exposed contact of the battery. Check the polarity of the battery to be installed and insert the battery so that the opposite polarity end goes into the battery compartment. To re-install the battery cover, reverse the steps taken to remove the cover. DO NOT OVERTIGHTEN THE KNURLED SCREW. Secure it with nger tightness only. Verify correct battery installation by turning on the sight and checking that the reticle image appears. If the batteries are left in the sight backwards, they will be drained of their power. ELECTRONIC FEATURES The Bushnell Holosight XLP controls are push-button switches located at the top of the unit as shown in Figure 1. To ensure proper operation of the push button switches, press the switch rmly. Audible and tactile feedback is provided when properly actuated. 1. ON/ Auto Battery Check Pressing either the Up or Down push-button switch will turn the sight ON. If the Up arrow is used to turn the sight ON it will be set at an 8 hour shutdown mode. That is, if the unit is not re-adjusted for brightness for a period of 8 hours, it will turn off. If the Down arrow is used to turn the sight ON it will be set at a 4 hour shutdown mode. See step 4 under this section for description of Auto shutdown. The sight will automatically perform a battery check every time it is turned on. If the batteries have less than 20% of life left, the sight will turn on with the reticle image blinking on and off for 5 seconds. If the remaining battery life is more than 20%, the sight will turn on with a steady reticle pattern. The battery condition can be checked any time by turning the sight off and on.

2. OFF To turn the sight off press both UP and DOWN push-button switches simultaneously. Verify that the unit is off by looking through the display window. 3. Brightness Adjustment Push-button switches vary the brightness intensity of the holographic reticle image. Pressing and releasing the push-button switch moves the brightness level UP or DOWN one (1) step from the previous setting. Pressing and holding the Up or Down push-button switch will change the brightness level up or down continuously. There are fteen (15) brightness settings providing a dynamic range of 100,000:1 from the lowest setting to the highest setting. When the sight is turned ON, the brightness intensity level is at Level 10. 4. Auto Shutdown The Bushnell Holosight XLP is equipped with an auto shutdown feature and will automatically shut itself OFF 8 or 4 hours after the last push-button control is used. This is determined by the method used to turn it ON in step 1. MOUNTING The Bushnell Holosight XLP is equipped with mounting hardware to attach to a Weaver-style rail or to a 12 gauge model 1100, 870 or 1187 Remington shotgun. To achieve the best results and accuracy, the Bushnell Holosight XLP must be mounted properly. For the Weaver-style rail mount, the base must be parallel to the bore to achieve the maximum elevation and windage adjustments.
To mount the sight to a Weaver-style rail, follow these steps, refer to Figure 3: 1. Loosen the 7/64 hex retainer screw that secures the clamp. 2. Place the sight onto the rail such that the unthreaded portion of the cross bolt is tted into a groove on the top of the Weaver-style rail. The users preference and the rearm will determine the optimal front to back position on the rail. 3. With the cross bolt inserted fully into the rails groove, push the sight as far forward as possible. 4. Tighten the hex retainer screw to draw the retainer nut into secure and fully seated contact with the opposite side of the rail. FIGURE 3
NOTE: Loosen the retaining screw just enough to mount or remove the sight. It is not necessary to remove the screw completely, as the lock hardware will not be retained in the sight and could be lost. To mount the sight to a 12 gauge Remington model 870, 1100 or 1187 shotgun, follow these steps, refer to Figure 4: 1. Remove the two through-pins from the shotgun. 2. Remove the two 1/8 hex retainer screws from the sight. 3. Place the sight onto the shotgun. 4. Re-install the two hex head screws through the sight and shotgun. 5. Tighten the two hex retainer screws to secure the sight to the shotgun. FIGURE 4
BORE SIGHTING AND ZEROING Bore sighting is a good preliminary procedure in achieving proper alignment of your sight to the rearm. If the sight is to be mounted to a Weaver-style rail, it is imperative that the base be parallel to the bore. Any major elevation adjustments may be accomplished by shimming the Weaver-style rail. It is important not to use the elevation adjustment of the sight for major adjustments. The sights elevation and windage adjustments should be used only for ne-tuning to achieve zero at the desired shooting distance. Final zeroing of your rearm and sight should be done with live ammunition. WINDAGE AND ELEVATION ADJUSTMENTS The Bushnell Holosight XLP has rotating adjustment features for elevation and windage adjustments. The feature at the back of the sight is the elevation adjustment and the feature at the front side of the sight is the windage adjustment. Both of the adjustment features have a slotted head that requires the use of a screwdriver, coin, or similar tool to rotate. The elevation and windage adjustments are shown in Figure 5. For both elevation and windage, each click will change the bullets point of impact 1/2 Minute of Angle (MOA), which translates to 1/4 inch at 50 yards, 1/2 inch at 100 yards. Also, one full rotation of either knob will change your point of impact 15 MOA. This translates into 8 inches at 50 yards, 15 inches at 100 yards. To move the point of impact UP, turn the adjustment counterclockwise; to move the point of impact DOWN, turn the adjustment screw clockwise. To move the point of impact RIGHT, turn the adjustment screw counterclockwise; to move the point of impact LEFT, turn the adjustment screw clockwise. The elevation and windage adjustments have been initially set at the factory near the midpoint of their adjustment ranges as well as parallel to the rail, and should be close to zero with a properly installed sight and mounting rail. Do not

make adjustments before mounting the sight on the rearm. Be sure to check that the mount and the sight remain fully secured after the rst 2 to 3 shots. CAUTION-When a sudden increase in resistance in the adjustment screw is felt, the end of the adjustment range has been reached. DO NOT try to turn the adjustments any further or damage may occur to the sight. FIGURE 5
MAINTENANCE AND CARE 1. The holographic image glass is coated with anti-reection material. When cleaning the glass surfaces, rst remove any dirt and dust with compressed air or by blowing on the glass surfaces. Fingerprints or lubricants can be wiped off with lens tissue or a soft cotton cloth, moistened with lens cleaning uid or glass cleaner. Never clean the glass surface with a dry cloth or paper towel; always dampen the glass surfaces prior to cleaning. 2. All moving parts of the sight are permanently lubricated. Do not try to lubricate them. 3. No maintenance is needed on the sights surface, except to occasionally wipe off with a soft cloth. Use only a water-based cleaner such as glass cleaner, ammonia, or soap and water. Never use any solventtype cleaner such as alcohol or acetone. 4. Never disassemble the sight. The optical cavity is nitrogen lled and sealed. Disassembly will void the warranty. LASER SAFETY The Bushnell Holosight XLP is a Class II laser product. The lasers illuminating beam, however, is contained within the housing. The only laser light accessible to the eye is at a power level within the limit of a Class IIa laser product. The lasers illuminating beam can become accessible to the eye if the housing is broken. Turn the sight off immediately and discontinue use until repaired.

WARRANTY / REPAIR

TWO-YEAR LIMITED WARRANTY Your Bushnell product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by someone other than a Bushnell Authorized Service Department. Any return made under this warranty must be accompanied by the items listed below: 1) A check/money order in the amount of $15.00 (USD) to cover the cost of postage and handling 2) Name and address for product return 3) An explanation of the defect 4) Proof of Date Purchased 5) Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage prepaid to the address listed below: IN U.S.A. Send To: Bushnell Performance Optics Attn.: Repairs 8500 Marshall Drive Lenexa, Kansas 66214 IN CANADA Send To: Bushnell Performance Optics Attn.: Repairs 25A East Pearce Street, Unit 1 Richmond Hill, Ontario L4B 2M9

For products purchased outside the United States or Canada please contact your local dealer for applicable warranty information. In Europe you may also contact Bushnell at: BUSHNELL Performance Optics Gmbh European Service Centre MORSESTRASSE 4 D- 50769 KLN GERMANY Tl: +49 (0) Fax: +49 (0) This warranty gives you specic legal rights. You may have other rights which vary from country to country. 2005 Bushnell Performance Optics

ENGLISH

FCC COMPLIANCE The Bushnell Holosight XLP complies with Part 15b of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
2005 Bushnell Performance Optics www.bushnell.com

Elektro Optik Sistemler

Product Binoculars, P/N 62-4201, 10x43 Elite Binocular w/XTR Description Specifications

Bushnell Binoculars

Binoculars, P/N 62-4208, 8x43 Elite Binocular w/XTR
Browning Binoculars, P/N 88-0826, 8x26 Roof Prism, Waterproof/Fogproof Browning Binoculars, P/N 88-0832, 8x32 Roof Prism, Waterproof/Fogproof Browning Binoculars, P/N 88-0833, 8x32 Roof Prism, Waterproof/Fogproof/Mossy Oak Camo Browning Binoculars, P/N 88-0842, 8x42 Roof Prism, Waterproof/Fogproof Browning Binoculars, P/N 88-1042, 10x42 Roof Prism, Waterproof/Fogproof Browning Binoculars, P/N 88-1043, 8x42 Roof Prism, Waterproof/Fogproof/Mossy Oak Camo Browning Riflescopes, P/N 882732M, 2-7x32mm, Matte

Browning Binoculars

Browning Riflescopes
Browning Riflescopes, P/N 883940M, 3-9x40mm, Matte
Browning Riflescopes, P/N 883950M, 3-9x50mm, Matte
Browning Riflescopes, P/N 884124M, 4-12x40mm, Matte, AO
Browning Riflescopes, P/N 885154M, 5-15x40mm, Matte, AO
Browning Riflescopes, P/N 888244M, 8-24x40mm, Matte, Mil Dot, AO Browning Sporting Scope, P/N 881545, 15-45x65 ED Class, Waterproof/Fogproof

Browning Sporting Scope

Camera Ballistic Range System
For recording images of external and terminal ballistic events;1280x1024 high resolution pixels; exposure times down to 200 nanoseconds; upto 16 exposures in a sequence. Cosists of a motor driven mirror to use with high speed camera or video system; framing rate capability of at least 500PPS with exposure times down to 100us. Imaging at 512x512 pixels; 1,000 PPS ful resolution images with allocation to 30,000PPS; adjustable to 10 microsecond exposure; Networkable via Fire Wire digital interface.
Camera Flight Follower System
Camera High Speed Image Digital System
Digital Trail Cameras, P/N 119600, Trail Scout VGA
Bushnell Digital Trail Camera
Digital Trail Cameras, P/N 119700, Trail Scout 1.3 MP
Digital Trail Cameras, P/N 119800, Trail Scout 2.1 MP
Digital Trail Cameras, P/N 119900, Trail Scout Pro 2.1 MP w/Night Vision
Elite 3200 W/Rainguard, P/N 321040M - 10x40, Matte, Mil Dot Ret.

Bushnell Riflescopes

Elite 3200 W/Rainguard, P/N 321546M - 1.5-4.5x32 Matte, Firefly Reticla
Elite 3200 W/Rainguard, P/N 322632M - 2-6x32, Matte, Long Eye Relief Handgun Elite 3200 W/Rainguard, P/N 322632S - 2-6x32, Silver, Long Eye Relief Handgun Elite 3200 W/Rainguard, P/N 322636M - 2-6x32, Matte, Firefly Reticle
Elite 3200 W/Rainguard, P/N 322732M - 2-7x32, Matte
Elite 3200 W/Rainguard, P/N 323104M - 3-10x40, Short Action Compact Elite 3200 W/Rainguard, P/N 323940G - 3-9x40, Glossy Elite 3200 W/Rainguard, P/N 323940S - 3-9x40, Silver Elite 3200 W/Rainguard, P/N 323944M - 3-9x40, Matte
Bushnell Riflescopes Bushnell Riflescopes
Elite 3200 W/Rainguard, P/N 323946M - 3-9x40, Matte, Firefly Reticle
Elite 3200 W/Rainguard, P/N 323954M - 3-9x50, Matte

Elite 3200 W/Rainguard, P/N 323955E - 3-9x50, Matte. European Reticle, 30mm Tube Elite 3200 W/Rainguard, P/N 323956M - 3-9x50, Matte. Firefly Reticle Elite 3200 W/Rainguard, P/N 323957M - 3-9x50, Matte, Firefly Reticle, 30mm Tube Elite 3200 W/Rainguard, P/N 324124A - 4-12x40, Matte, Adjustable Objective
Elite 3200 W/Rainguard, P/N 324124B - 4-12x40, Matte, Ballistic Reticle Elite 3200 W/Rainguard, P/N 325154M - 5-15x40, Matte, Adjustable Objective Elite 3200 W/Rainguard, P/N 325155M - 5-15x50, Matte, Adjustable Objective Elite 3200 W/Rainguard, P/N 325156M - 5-15x40, Matte, Fire Reticle
Elite 3200 W/Rainguard, P/N 327214M - 7-21x40, Matte
Elite 4200 W/Rainguard, P/N 421636M - 1.5-6x36, Matte
Elite 4200 W/Rainguard, P/N 421637M - 1.5-6x36, Matte, Firefly Reticle Elite 4200 W/Rainguard, P/N 422104G - 2.5-10x40, Gloss Elite 4200 W/Rainguard, P/N 422104M - 2.5-10x40, Matte Elite 4200 W/Rainguard, P/N 422104S - 2.5-10x40, Silver Elite 4200 W/Rainguard, P/N 422105M - 2.5-10x50, Matte
Elite 4200 W/Rainguard, P/N 422106M - 2.5-10x50, Matte, Firefly Reticle Elite 4200 W/Rainguard, P/N 422146M - 2.5-10x40, Matte, Firefly Reticle Elite 4200 W/Rainguard, P/N 422151M - 2.5-10x50, Matte, Illuminated Dot Reticle
Elite 4200 W/Rainguard, P/N 424164M - 4-16x40, Matte
Elite 4200 W/Rainguard, P/N 424165M - 4-16x50, Matte, Adjustable Objective Elite 4200 W/Rainguard, P/N 426242M - 6-24x40, Matte, Mil Dot Reticle
Elite 4200 W/Rainguard, P/N 426243A - 6-24x40, Matte, 1/4
Elite 4200 W/Rainguard, P/N 426244M - 6-24x40, Matte, Adjustable Objective Elite 4200 W/Rainguard, P/N 428324M - 8-32x40, Matte, Adjustable Objective
Holosight, P/N 51-0021, Standard Reticle Model (N batteries)

Bushnell Holosight

Holosight, P/N 53-0021, HOLOsight XLP (AAA batteries)
Holosight, P/N 53-0027, HOLOsight XLP for REM 870, 1187(AAA batteries)
Yardage Pro Lager Rangefinders, P/N 20-0001, Scout
Bushnell Laser Rangefinders
Yardage Pro Lager Rangefinders, P/N 20-0003W, Legend Waterproof
Yardage Pro Lager Rangefinders, P/N 20-1319, Legend w/Mossy Oak Camo, Waterproof Yardage Pro Lager Rangefinders, P/N 20-1920, Sport 450 w/Mossy Oak Break-Up Camo
Yardage Pro Lager Rangefinders, P/N 20-2018, Trophy
Yardage Pro Lager Rangefinders, P/N 20-2020, Trophy w/Mossy Oak Camo Yardage Pro Lager Rangefinders, P/N 20-3000, Scout w/Realtree Hardwoods HD Camo