If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. Keep the camera from the reach of small children. The neck strap can accidentally choke the child. Do not store the equipment in dusty or humid places. This is to prevent re and electrical shock. Before using the camera inside an airplane or hospital, check if it is allowed. Electromagnetic waves emitted by the camera may interfere with the planes instruments or the hospitals medical equipment. To prevent re and electrical shock, follow the safeguards below: - Always insert the power plug all the way in. - Do not handle a power plug with wet hands. - When unplugging a power plug, grasp and pull the plug instead of the cord. - Do not scratch, cut, or excessively bend the cord or put a heavy object on the cord. Also do not twist or tie the cords. - Do not connect too many power plugs to the same power outlet. - Do not use a cord whose insulation has been damaged. Occasionally unplug the power plug and use a dry cloth to clean off the dust around the power outlet. If the surrounding is dusty, humid, or oily, the dust on the power outlet may become moist and short-circuit the outlet to cause a re.
Preventing Injury or Equipment Damage
Do not leave equipment inside a car under the hot sun or near a heat source. The equipment may become hot and cause skin burns. Do not carry the camera around while it is attached to a tripod. Doing so may cause injury. Also make sure the tripod is sturdy enough to support the camera and lens. Do not leave a lens or lens-attached camera under the sun without the lens cap attached. Otherwise, the lens may concentrate the suns rays and cause a re. Do not cover or wrap the battery-recharging apparatus with a cloth. Doing so may trap heat within and cause the casing to deform or catch re. If you drop the camera in water or if water or metal fragments enter inside the camera, promptly remove the battery pack and back-up battery. This is to prevent re and electrical shock. Do not use or leave the battery pack or back-up battery in a hot environment. Doing so may cause battery leakage or a shorter battery life. The battery pack or back-up battery can also become hot and cause skin burns. Do not use paint thinner, benzene, or other organic solvents to clean the equipment. Doing so may cause re or a health hazard.

Shutter Button

The shutter button has two stages. You can press the shutter button halfway. Then you can further press the shutter button completely.
Pressing halfway (9) This activates autofocusing (AF) and automatic exposure (AE) that sets the shutter speed and aperture. The exposure setting (shutter speed and aperture) is displayed on the top LCD panel and in the viewnder. Pressing completely
This releases the shutter and takes the picture.
If you press the shutter button halfway and (9) elapse, you must press it halfway again and wait a moment before pressing it completely to take a picture. If you press the shutter button completely without pressing it halfway rst or if you press the shutter button halfway and then press it completely immediately, the camera will take a moment before it takes the picture. No matter what state the camera is in (image playback, menu operation, image recording, etc.), you can return to shooting instantly just by pressing the shutter button halfway.

Using the <6> Dial

The <6> dial is mainly used for shooting-related settings. There are three ways to use this dial:
(1) While pressing a button, turn the <6> dial until the desired setting appears on the top LCD panel.
When you release the button, the selected setting takes effect and the camera will be ready to shoot. In this way, you can set the shooting mode, AF mode, metering mode, drive mode, etc.
(2) After pressing a button, turn the <6> dial.
When you press a button, its function remains selected for 6 seconds (9). During this time, you can turn the <6> dial to set the desired setting. After the button turns off or if you press the shutter button halfway, the camera will be ready to shoot. In this way, you can select the AF point or press the <O> button to set the exposure compensation amount.
(3) Turn the <6> dial only.
While referring to the top LCD panel, turn the <6> dial. In this way, you can set the shutter speed, aperture, etc.

Using the <5> Dial

The <5> dial is used for AF point selection and selecting the desired setting on the LCD monitor. This <5> dial works only when the <7> switch is set to <1>. There are three ways to use this <5> dial:

2 Select a menu tab (zxcbn).
Hold down the <M> button and turn the <5> dial to select a tab, then let go of the button.
a menu 3 Select down the <item. > button and Hold X
turn the <5> dial to select a menu item, then let go of the button.
the 4 Select downdesired menu setting. Hold the <X> button and
turn the <5> dial to select the desired setting, then let go of the button. The setting will take effect immediately.
menu. 5 Exit thethe <M> button to exit. Press

Menu Settings

<z> Shooting menu
Custom WB JPEG Quality Manual setting of white balance Compression rate for 3, 4, 5, 6. Standard Set 1 Set 2 Set 3 Set up 1 Standard 2 Portrait 3 High saturation 4 Adobe RGB 5 Low saturation 6 CM set CM set 2 Set up Off On On (Info) 2 sec. 4 sec. 8 sec. Hold Off On Off On

Review time

Noise reduction ISO expansion

Parameters

<x> Playback menu
Protect images Rotate Erase all on card Print Order Highlight alert Display AF points Histogram display Erase protected Rotate image Erase all data Species images to be printed Off On Off On Bright. RGB

Color matrix

Review

<c> Set-up 1 menu

1 min. 2 min. 4 min. 8 min. 15 min. 30 min. Off

<b> Set-up 2 menu

LCD Brightness Date/Time Language Video system Firmware Sensor cleaning 5 levels Date/time setting 12 languages NTSC PAL Select when updating rmware Select to clean sensor

Auto power off

Auto Reset File numbering Continuous Manual Reset BackUp mode Auto rotate Save camera settings Off CF card main SD card main On Off Save settings to memory card
<n> Custom / Personal Functions menu
Custom Functions (C.Fn) Personal Functions (P.Fn) Clear all Custom Functions Clear all Personal Functions Customize the camera Register Custom Function Groups. This clears all the Custom Function settings to the default settings. This clears all the Personal Function settings.
Loading Read settings saved camera setting in memory card Format Initializes and erases card
Languages provided: English, German, French, Dutch, Danish, Finnish, Italian, Norwegian, Swedish, Spanish, Simplied Chinese, Japanese

About the LCD Monitor

When using the LCD monitor, you can use the <5> dial even while the <7> switch is <2>. The LCD monitor cannot be used as a viewnder to shoot. To adjust the LCD monitors brightness, select the <b> menu tab and select [LCD Brightness].
Restoring the Default Settings Press the <N> button and <B> button simultaneously for 2 sec.
The cameras default settings will be as shown below. Image-Recording Settings

turn the <5> dial to select one of the following display formats: [mm/dd/yy], [dd/mm/yy], [yy/mm/dd]. Then let go of the button.
the <M> 4 Pressdate and time willbutton.and the The be set

menu will reappear.

Each captured image is recorded with the date and time it was taken. If the date and time are not properly set, the wrong date/time will be recorded. Make sure you set the date and time correctly.
Replacing the Date/Time Battery
The date/time (back-up) batterys service life is about 10 years. If the date/time is reset, replace the back-up battery with a new CR2025 lithium battery as described below.
Set the <4> switch to <2> and remove the battery pack.
The back-up battery is on the ceiling of the battery compartment.
2 Remove the back-up battery cover.
As shown in the diagram, loosen the screw to remove the cover.

3 Remove the battery.

a 4 Installplusnew back-up battery. face The side of the battery must
cover. 5 Attach the battery and turn the <4> Install the
switch to <1>. The date/time will be displayed on the LCD monitor. Set the the date/time.
3Cleaning the CMOS sensor
The CMOS sensor is like the lm in a lm camera. If any dust or other foreign matter adheres to the CMOS sensor, it may show up as a dark speck in the pictures you take. To avoid this, follow the procedure below to clean the CMOS sensor. Note that the CMOS sensor is very delicate. If possible, you should have it cleaned by a Canon Service Center. When you want to clean the CMOS sensor, use the DC Coupler Kit to power the camera with a household power outlet. If you use the battery, make sure it is fully charged. Before cleaning the sensor, detach the lens from the camera.
Install the DC Coupler battery and turn the <4> switch to <1>.
cleaning]. 2 Select [Sensor > tab. Select the <b
Hold down the <X> button and turn the <5> dial to select [Sensor cleaning]. Then let go of the <X> button.
[OK]. 3 Select down the <X> button and Hold

The higher the recording quality, the fewer the number of possible shots will be. On the other hand, the lower the recording quality, the higher the number of possible shots will be. JPEG quality levels 1 to 5 are indicated by <o>, and levels 6 to 10 are indicated by <i>.

Setting the ISO Speed

The ISO speed is a numeric indication of the sensitivity to light. A higher ISO speed number indicates a higher sensitivity to light. Therefore, a high ISO speed is suited for low light and moving subjects. However, the image may look more coarse with noise, etc. On the other hand, a low ISO speed is not suited for low light or action shots, but the image will look ner. The camera can be set between ISO 100 and 1600 in 1/3-stop increments.
Hold down the <E> and <Q> buttons simultaneously.
The current ISO speed will be displayed on the LCD panel.
> dial. 2 Turn the <<6> dial until the desired Turn the 6
ISO speed is displayed on the LCD panel, then let go of the buttons. s The ISO speed will be set.
At higher ISO speeds and higher ambient temperatures, the image will have more noise. High temperatures, high ISO speeds, or long exposures may cause irregular colors in the image.

ISO speed extension

Under the <z> tab, set [ISO expansion] to <On> to enable ISO 50 or 3200 to be set. When set, ISO 50 is indicated by L and ISO 3200 by H.
3Selecting the White Balance
Normally, the <Q> setting will set the optimum white balance automatically. If natural-looking colors cannot be obtained with <Q>, you can set the white balance manually to suit the respective light source.
Select the white balance setting.
Hold down the <B> button and turn the <5> dial to select the desired white balance. Then let go of the button.
:Auto (Approx. 3000K-7000K) :Daylight (Approx. 5200K) :Shade (Approx. 7000K) :Cloudy, twilight, sunset (Approx. 6000K) :Tungsten light (Approx. 3200K) :White uorescent light (Approx. 4000K) :Flash (Approx. 6000K) :Custom (Approx. 2000K-10000K) Set the optimum white balance manually to suit the lighting. (p.49) P :Color temperature (Approx. 2800K-10000K) PC-1, PC-2, PC-3 Personal white balance Use the provided software to register Personal white balance settings. Not displayed if no Personal white balance settings have been registered.

Q W E R Y U I O

About White Balance
The three RGB (red, green, and blue) primary colors exist in the light source in varying proportions depending on the color temperature. When the color temperature is high, there is more blue. And when the color temperature is low, there is more red. To the human eye, a white object looks white regardless of the type of lighting. With a digital camera, the color temperature can be adjusted with software so that the colors in the image look more natural. The subjects white color is used as the criteria for adjusting the other colors. The cameras <Q> setting uses the CMOS sensor for auto white balance.

3Custom White Balance

With custom white balance, you shoot a white object that will serve as the basis for the white balance setting. By selecting this image, you import its white balance data for the white balance setting.
Photograph a white object.
Make sure the plain, white subject lls the entire center spot metering circle. Set the lens focus mode switch to <g>, then focus manually. (p.76) Set any white balance setting. (p.48) Shoot the white object so that a standard exposure is obtained. If it is underexposed or overexposed, a correct white balance setting might not be obtained.
2 Select [Custom WB]. Select the <z> tab.
Hold down the <X> button and turn the <5> dial to select [Custom WB]. Then let go of the button. s The 9-image index display will appear.
the 3 Select downimage. > button and Hold the <X
turn the <5> dial to select the image you shot in step 1. Then let go of the button.
the balance data. 4 ImportdownwhiteX> button and Hold the <
turn the <5> dial to select [OK]. Then let go of the <X> button. s The images white balance data will be imported.
<O 5 Select down >. <B> button and turn Hold the
the <5> dial to select <O>. Then let go of the <B> button. s The custom white balance will be set.
Instead of a white object, an 18% gray card (commercially available) can produce a more accurate white balance.
Setting the Color Temperature
You can numerically set the white balances color temperature.
Select <P> for the white balance.
Hold down the <B> button and turn the <5> dial to select <P>.
color 2 Set thedown thetemperature. and turn Hold <B> button
the <6> dial to set the desired color temperature. Then let go of the button. The color temperature can be set from 2800K to 10000K in 100K increments.
When setting the color temperature for an articial light source, set white balance correction (magenta or green) as necessary. If you want to set <P> to the reading taken with a color temperature meter, take test shots and adjust the setting to compensate for the difference between the color temperature meters reading and the cameras color temperature reading.

White Balance Correction

You can correct the standard color temperature for the white balance setting. This adjustment will have the same effect as using a color temperature conversion or color compensating lter. Each color can be corrected to one of nine levels. Users familiar with using color temperature conversion or color compensating lters will nd this feature handy.

the display. 3 Checkshutter speed and aperture value The
will be set automatically and displayed in the viewnder and on the LCD panel. As long as the shutter speed is not blinking, the exposure will be correct.
4 Take the picture. and press the Compose the shot
shutter button completely.
If 30 and the maximum aperture blink, it indicates underexposure. Increase the ISO speed. Or use ash. If 8000 and the minimum aperture blink, it indicates overexposure. Decrease the ISO speed. Or attach a neutral density lter to the lens. If automatic AF point selection (p.68) has been set, all the AF points that achieve focus will light. d stands for Program. AE stands for Auto Exposure. If the focus conrmation light <o> blinks, the shutter will lock and a picture cannot be taken. You can freely change the shutter speed and aperture combination (program) while retaining the same exposure. This is called program shift. To shift the program, press the shutter button halfway and turn the <6> dial until the desired shutter speed or aperture is displayed. After you take the picture, the program shift will be canceled.

sShutter-Priority AE

In this mode, you set the shutter speed and the camera automatically sets the aperture value to suit the brightness of the subject. This is called Shutter-Priority AE. A fast shutter speed can freeze the motion of a fast-moving subject and a slow shutter speed can blur the subject to give the impression of motion. *s stands for Time value.

Fast shutter speed

Slow shutter speed
Select <s> on the LCD panel.
Hold down the <W> button and turn the <6> dial to select <s>. Then let go of the button.
shutter 2 Set theatdesiredLCD panelspeed. Look the top and turn

the <6> dial.

subject. 3 Focus the shutter button halfway. Press the
The aperture value is set automatically.
4 Check the viewnder display and shoot.
As long as the aperture value is not blinking, the exposure will be correct.
If the maximum aperture blinks, it indicates underexposure. Turn the <6> dial to set a slower shutter speed until the aperture value stops blinking. Or increase the ISO speed.

AEB with the Shutter Speed or Aperture

Set the AEB amount.

Press the <W> and <E> buttons simultaneously and turn the <6>. The diagram on the left shows an AEB amount of 1 stop centering on the standard exposure level. The AEB amount (1.0), the AEB range <N>, and the <h> icon will be displayed.
2 Take the picture.exposure level The viewnders

Standard exposure

Decreased exposure

Increased exposure

indicator will indicate the respective bracketing amount as each shot is taken. The current drive mode will be used for the AEB shooting. After the three bracketed shots are taken, AEB will not be canceled. To cancel AEB, set the AEB amount to 0.0.

AEB with the ISO Speed

Set the ISO speed that is to be the standard AEB exposure. For example, if you want AEB with 1 stop and ISO 200, 400, and 800, set the ISO speed to 400.
Hold down the <E> and <Q> buttons simultaneously and turn the <5> dial. The diagram on the left shows an AEB amount of 1 stop centering on the standard exposure level. The AEB amount (1.0), the AEB range <N>, and the <i> icon will be displayed. The shooting operation will be the same as AEB shooting while changing the shutter speed or aperture.
AEB shooting (by changing the shutter speed/aperture or ISO speed) cannot be used with ash photography and bulb exposures. AEB shooting is possible only within the settable shutter speed range (1/ 8000 - 30 sec. ), aperture range, and ISO speed range (100 - 1600). It is not possible with ISO 50 and 3200 even if the ISO speed extension is [On]. If you use C.Fn-06-2 to set the exposure setting increment to 1/2 stop, AEB shooting with the ISO speed will not be possible. In the continuous shooting mode, holding down the shutter button will take all three bracketed shots continuously, then the shooting will stop automatically (except during mirror lockup). When AEB is used with the self-timer, the three bracketed shots will be taken in succession after the 2- or 10-second self-timer delay. If the drive mode is set to single shooting, press the shutter button three times to take the three AEB shots. AEB can be combined with exposure compensation. During AEB shooting, the <w> icon in the viewnder and the <h> or <g> icon on the LCD panel will blink.

AAE Lock

AE lock enables you to lock the exposure at a different place from the point of focus. After locking the exposure, you can recompose the shot while maintaining the desired exposure level. This feature is useful for backlit and spotlighted subjects.
1 Focus the subject. Press the <w> button. 2 Aim the viewnder center(9) the over
subject where you want to lock the exposure, then press the <A> button. s The <w> icon will light in the viewnder and the exposure setting will be locked (AE lock). Each time you press the <A> button, it locks the current exposure setting.

Flash Photography

With EX-series Speedlites
An EOS-dedicated, EX-series Speedlite makes ash photography as easy as any AE mode. For details on using the EX-series Speedlite, refer to the Speedlites instruction manual. The EOS-1Ds Mark II is a Type-A camera compatible with all EX-series Speedlites providing the features below.

E-TTL II Autoash

E-TTL II is a new autoash exposure system incorporating improved ash exposure control and lens focusing distance information, making it more precise than the previous E-TTL (evaluative ash metering with preash) system.The camera can execute E-TTL II autoash with any EX-series Speedlite.
High-Speed Sync (FP Flash)
High-speed sync (FP or focal-plane ash) enables ash synchronization with all shutter speeds from 30 sec. to 1/8000 sec.

FE (Flash Exposure) Lock

Press the cameras <I> button to lock the ash exposure at the desired part of the subject. This is the ash equivalent of AE lock.
Flash exposure compensation
In the same way as normal exposure compensation, you can set exposure compensation for ash. Set ash exposure compensation up to 3 stops in 1/3-stop increments.
FEB (Flash Exposure Bracketing)
FEB is the ash version of AEB. (Only with FEB-compatible Speedlites.) Set ash exposure bracketing up to 3 stops in 1/3-stop increments.
E-TTL II wireless autoash with multiple Speedlites
Like with wired, multiple Speedlites, E-TTL II wireless autoash with multiple Speedlites provides all the above features. Since connection cords are unnecessary, exible and sophisticated lighting setups are possible. (Only with wireless-compatible Speedlites.)
Metered Manual Flash Exposure
For closeup ash photography, you can set the ash exposure manually. With an EX-series Speedlite having a manual ash mode, follow the procedure below:
1 Set the camera and Speedlite settings. 2 Focus the subject.

Focus manually.

Set the cameras shooting mode to <a> or <f>. Set the Speedlite to manual ash.
3 Aim the center spot metering circle over the subject,
then press the <FEL> button (8).
The Speedlite will re a preash and the required ash output is retained in memory. s In the viewnder, the exposure level indicator will indicate the currently-set ash exposure level relative to the standard exposure index.

Select the type of paper to be loaded in the printer.
About the Paper Type If you are using a Canon printer with Canon paper, set the respective paper type as follows:
Photo Default Photo Paper Plus Glossy Photo Paper Plus Glossy Fast Photo Photo Paper Pro
If you are using a non-Canon printer, refer to the printers instruction manual for the recommended paper type settings.

USetting the Page Layout

Select the desired layout. s The print settings screen will reappear.

About Page Layout

Bordered Borderless 8-UP Default The print will have a white border along the edges. The print will have no white borders. If your printer cannot print borderless prints, the print will have borders. Eight copies of the same image will be printed on a single sheet. With a Canon printer, the print will be borderless.
the other 4 Set desired, alsooptions.<H> date If set the
imprinting, <E> printing effects, and <R> number of copies.
H[Date imprinting] E[Printing effects] R[Number of copies]
Depending on the BJ printer, the <E> Printing effects setting may enable you to select the [VIVID] (for vivid greens and blue sky), [NR] (noise reduction), or [VIVID+NR] setting. For details on trimming, see page 135.
image. 5 Print the[Print]. Select
The printing will start. When the printing ends, the screen will return to step 1. To stop printing, press the <X> button while [Stop] is displayed, then select [OK].
Depending on the images size and recording quality, it may take some time for the printing to start after you select [Print]. The [Default] setting for printing effects and other options are the printers own default settings as set by the printers manufacturer. See the printers instruction manual to nd out what the default settings are.

Handling Printer Errors

If you resolve a printer error (no ink, no paper, etc.) and select [Continue] to resume printing but it does not resume, operate the printer to resume printing. For details, see the printers instruction manual.

Error Messages

If a problem occurs during printing, an error message will appear on the cameras LCD monitor. Press the <X> button to stop printing. After resolving the problem, resume printing. For details on how to resolve a printing problem, refer to the printers instruction manual. Paper Error Check whether the paper is properly loaded in the printer. Ink Error The printer has run out of ink or the waste ink tank is full. Hardware Error Check for any printer problems other than paper and ink problems. File Error You attempted to print an image that cannot be printed with PictBridge. Images taken with a different camera or images edited with a computer might not be printable.

APrinting with CP Direct

Check that the <A> icon is displayed on the upper left of the LCD monitor.
Trimming frame: Appears when you want to trim the image. Sets the quantity to be printed. Sets the trimming area. Sets the printing style. Returns to step 1. You can also press the <7> button to return to step 1. Starts the printing. The printing style settings will be displayed. <H> is the date icon.
[Style]. 3 SelectStyle screen will appear. The
4 Set the options.[Borders], and [Date] Set the [Image],

as desired.

[Image] [Borders] [Date]
[Image] is selectable when card-size paper is used. If you set [Multiple], 8 small images of the same picture will be printed on the paper. Check the [Borders] and [Date] settings and set them if necessary. When you are done, press the <7> to return to the print setting screen.
5 Set the number of copies and trimming.
Set as necessary. For details on trimming, see page 135.
image. 6 Print the[Print]. Select
The printing will start. When the printing ends, the screen will return to step 1. To cancel the printing, press the <X> button while [Stop] is displayed, then select [OK].
The date may look light if it is imprinted on a bright background or border. If [Multiple] is selected, [Borders] and [Date] cannot be selected. [Borderless] will be set and [Date] will be set to [Off]. The image will also be cut off along all four edges. If [Date] is set to [On], the recorded date will be imprinted on the lower right of the print. If you select [Stop] while printing only one picture, the printing will not stop until it nishes printing the picture. If you are printing multiple pictures, the printing will stop after the current picture is nished printing. If a problem occurs during printing, an error message will appear on the camera's LCD monitor. Select [Stop] or [Resume] (after resolving the problem). If [Resume] is not displayed, select [Stop].

Depending on the printer, the trimmed image area might not be printed as you specied. The smaller you make the trimming frame, the grainier the picture will look. If the picture will be too grainy, the trimming frame will turn red. When trimming the image, look at the cameras LCD monitor. If you look at the image on a TV screen, the trimming frame might not be displayed accurately. The trimming frame will be different depending on the [Paper], [Image], and [Borders] settings.
DPOF: Digital Print Order Format
With DPOF (Digital Print Order Format), you can specify which images in the Memory card are to be printed and the quantity. This feature is very convenient when you make prints with a DPOF-compatible printer or photo lab.
DPOF DPOF (Digital Print Order Format) is a standard for recording print ordering instructions to the memory card. It is for images taken with a digital camera, and you can specify which photos and the quantity to print. With a DPOF-compatible digital camera, you can do the following: By tting a Memory card into a printer compatible with DPOF, you can make prints as specied. Printers capable of direct printing from the camera can print the images as specied by DPOF. When ordering prints from a photo lab, you do not need to ll in any order form to specify the image selections, quantity, etc.

Print Order

Print settings
Set the print type, date imprinting, and le No. imprinting. The print settings will be applied to all print-ordered images. (They cannot be set individually for each image.) The print settings are set in the same way as with menu settings.

Print Type

Standard Index Both
Prints one image on the paper. Multiple, thumbnail images are printed on the paper. Prints both the standard and index prints.

Date File No.

On Off On Off
[On] imprints the recorded date on the print. [On] imprints the le No. on the print.

Select [Print Order].

The print order screen will appear.
[Set 2 Selectset up up]. will appear. The screen
3 Set the options as desired. [File Set the [Print Type], [Date], and

[Print Type]

[Date]

[File No.]

Exit the set up 4 Press the <7screen. > button.
s The Print Order screen will reappear. Next, select [Order] or [All] to select the images to be printed.
1 images cannot be selected for printing. Even if [Date] and [File No.] are set to [On], the date or le No. might not be imprinted depending on the print type setting and printer type. (See the table below.) Print Type Standard Index* Both Standard Date Yes Yes Yes File No. No Yes No

AF point activation area

1: The AF point activation area expands by one point all around the manually-selected AF point. A total of 7 AF points become active. This setting is effective for when only one manually-selected AF point is unable to focus track a subject moving erratically. 2: The camera automatically sets the AF point activation area to 7 or 13 points to suit the lens focal length and AF mode.This is effective when the subjects movement is unpredictable.
The AF point activation area centers on the selected AF point. Therefore, if a peripheral AF point is selected, the AF point activation area will be smaller as shown below.
7-point activation area Selected AF point Activation area 13-point activation area
Setting C.Fn-13 will also expand the AF point activation area.

C.Fn-18

Switch to the registered AF point
1: Press the <P> button to switch to the registered AF point. 2: Switch to the registered AF point only while you press the <P> button. When you release the button, the AF point selected previously becomes active again. You can thereby easily switch between the selected AF point and registered AF point.
If C.Fn-04-1/3 is also set, you can press the <P> button to switch to the registered AF point and start the AF at the same time.

C.Fn-19

Lens AF stop button function
1: AF operates only while the AF stop button is pressed. While the button is pressed, AF operation with the camera is disabled. 2 : When the button is pressed while metering is still active, AE lock takes effect. Convenient when you want to focus and meter separately. 3 : In the manual AF point selection mode, holding down the button switches to automatic AF point selection (among 45 AF points). Holding down the button switches from manual AF point selection to automatic AF point selection instantly. Convenient when you are no longer able to focus track a moving subject with a manuallyselected AF point in the AI Servo AF mode. In the automatic AF point selection mode, the center AF point is selected only while you hold down the button. 4 : In the One-Shot AF mode, the camera switches to AI Servo AF mode only while you hold down the button. In the AI Servo AF mode, the camera switches to One-Shot AF mode only while you hold down the button. Convenient when you need to keep switching between One-Shot AF and AI Servo AF for a subject which keeps moving and stopping. 5: With the lens IS switch already ON, the Image Stabilizer operates only while you press the button.

About the

Symbols
: Warning to prevent shooting problems. : The Note symbol gives supplemental information.

Basic Assumptions

All operations explained in this manual assume that the power switch is already set to <1> or <J>. (p.36) <5> operations explained in this manual assume that the power switch is already set to <J>. It is assumed that all the menu settings and Custom Functions are set to the default. It is assumed that a memory card (CF card <f> or SD card <g>) is being used. For explanatory purposes, the instructions show the camera attached with an EF50mm f/1.4 USM lens.

Contents

Introduction
Item Check List...3 Conventions Used in this Manual...4 Index to Features....8 Handling Precautions....12 Quick Start Guide...14 Nomenclature....16

Getting Started

Recharging the Battery...26 Installing and Removing the Battery...29 Using a Household Power Outlet...31 Installing and Removing the Memory Card..32 Mounting and Detaching a Lens...35 Basic Operation...36 Menu Operations....41 Menu Settings....43 Before You Start....46 Setting the Interface Language...46 Setting the Date and Time...46 Set the power-off time/Auto power off...47 Formatting the Memory Card..47 Reverting Camera Settings to the Default..49

Image Settings

Setting the Image-recording Quality...52 Selecting the Image Size...52 Setting the JPEG Quality (Compression Rate)..55 Setting the ISO Speed...56 Selecting a Picture Style....57 Customizing the Picture Style...59 Registering the Picture Style...61 Selecting the White Balance...63 Custom White Balance...64 Setting the Color Temperature...69 White Balance Correction...70 Setting the Color Space...72 Selecting the Media, Folder, and Recording Method..73 Changing the File Name....77 File Numbering Methods....79
Setting the AF and Drive Modes
Selecting the AF Mode... 82 Selecting the AF Point... 84 When Autofocus Fails... 86 Manual Focusing... 86 Selecting the Drive Mode... 87 Self-timer Operation... 88

Exposure Control

If you drop the equipment and the casing breaks open to expose the internal parts, do not touch the internal parts due to the possibility of electrical shock. Do not disassemble or modify the equipment. High-voltage internal parts can cause electrical shock. Do not look at the sun or an extremely bright light source through the camera or lens. Doing so may damage your vision. Keep the camera from the reach of small children. The neck strap can accidentally choke the child. Do not store the equipment in dusty or humid places. This is to prevent fire and electrical shock. Before using the camera inside an airplane or hospital, check if it is allowed. Electromagnetic waves emitted by the camera may interfere with the planes instruments or the hospitals medical equipment. To prevent fire and electrical shock, follow the safeguards below: - Always insert the power plug all the way in. - Do not handle a power plug with wet hands. - When unplugging a power plug, grasp and pull the plug instead of the cord. - Do not scratch, cut, or excessively bend the cord or put a heavy object on the cord. Also do not twist or tie the cords. - Do not connect too many power plugs to the same power outlet. - Do not use a cord whose insulation has been damaged. Occasionally unplug the power plug and use a dry cloth to clean off the dust around the power outlet. If the surrounding is dusty, humid, or oily, the dust on the power outlet may become moist and short-circuit the outlet to cause a fire.
Preventing Injury or Equipment Damage
Do not leave equipment inside a car under the hot sun or near a heat source. The equipment may become hot and cause skin burns. Do not carry the camera around while it is attached to a tripod. Doing so may cause injury. Also make sure the tripod is sturdy enough to support the camera and lens. Do not leave a lens or lens-attached camera under the sun without the lens cap attached. Otherwise, the lens may concentrate the suns rays and cause a fire. Do not cover or wrap the battery-recharging apparatus with a cloth. Doing so may trap heat within and cause the casing to deform or catch fire. If you drop the camera in water or if water or metal fragments enter inside the camera, promptly remove the battery pack and back-up battery. This is to prevent fire and electrical shock. Do not use or leave the battery pack or back-up battery in a hot environment. Doing so may cause battery leakage or a shorter battery life. The battery pack or back-up battery can also become hot and cause skin burns. Do not use paint thinner, benzene, or other organic solvents to clean the equipment. Doing so may cause fire or a health hazard.

Nomenclature

Lens mount index (p.35) Self-timer lamp (p.88) Lens lock pin Shutter button (p.36) Strap mount (p.24) Lens release button (p.35) Mirror (p.104)
Lens mount Contacts (p.13) Grip
Depth-of-field preview button (p.97) Vertical-grip on/off switch (p.39) <I> Vertical-grip FE lock/ Multi-spot metering button (p.39, 105/91) Vertical-grip Main Dial (p.39, 37) Hand strap mount Vertical-grip shutter button (p.39, 36)
Tripod socket Body number

Body cap (p.35)

<U> LCD panel illumination button (p.102) Hot shoe Flash-sync contacts <V> Focal plane mark <Q> Metering mode selection/Flash exposure compensation button (p.90/105) <W> Shooting mode selection button (p.92) <o> AF mode selection/Drive mode selection button (p.82, 87) <Y> AEB set button (p.100)
<O> Exposure compensation/ Aperture button (p.99/98) <I> FE lock/Multi-spot metering button (p.105/91) <i> ISO speed set button (p.56) <6> Main Dial (p.37) Top LCD panel (p.19) <p> AF start button (p.82/83) <A/y> AE lock/ Reduce button (p.101/120, 146) <S/u> AF point selection/ Magnify button (p.84/112, 120, 146) Eyepiece shutter lever (p.103) <9> Multicontroller (p.38)

Strap mount (p.24)

Dioptric adjustment knob (p.39) Viewfinder eyepiece Battery release handle (p.29, 30) Battery (p.26) Power/Quick Control Dial switch (p.36) <0> Setting button (p.41)
<5> Quick Control Dial (p.38) <A/y> Verticalgrip AE lock/ Reduce button (p.39, 101/120, 146) <S/u> Verticalgrip AF point selection/Magnify button (p.39, 84/ 112, 120,146) <p> Verticalgrip AF start button (p.39, 82, 83)
<B> Info/Trimming orientation button (p.114, 116, 186/146) <M> Menu button (p.41) WFT-E2/E2A mounting hole Extension system terminal
LCD Monitor (p.41, 129) Eyecup (p.39) SD card slot* (p.32) Memory card slot cover (p.32)

Terminal cover

CF card slot (p.32)
CF card eject button (p.33) Access lamp (p.34) Memory card slot cover release handle (p.32) <x> Playback button (p.116) <L> Erase button (p.128) Rear LCD Panel (p.20) Recording microphone (p.124) <H> Protect/Sound recording button (p.123/124)/ <A> Picture Style setting button (p.57) <B> Function button (p.52, 63, 69, 73) <D> PC terminal (p.108) <F> Remote control terminal (N3 type) (p.103) <q> VIDEO OUT terminal (p.122) <D> DIGITAL terminal (p.138, 152) Battery compartment cap (p.29)

About Low-level Formatting
When [g] SD card is selected, low-level formatting is possible. If the writing speed to the SD card is slower than usual or if you want to completely erase the data in the SD card, checkmark [Low level format] and format the card.
Press the <L> button.
In step 3 on the preceding page, press the <L> button. The [Low level format] option will be checkmarked <X>. With <X> displayed, select [OK] to start the low-level formatting.
Since low-level formatting will erase all recordable sectors in the SD card, the formatting will take slightly longer than normal formatting. You can stop the low-level formatting by selecting [Cancel]. Even in this case, normal formatting will have been completed and you can use the SD card as usual.
3 Reverting Camera Settings to the Default
The cameras shooting settings and menu settings can be reverted to the default.
Select [Clear all camera settings].
Under the [7] tab, select [Clear all camera settings], then press <0>.
2 Select [OK]. dial to select [OK], Turn the <5>
then press <0>. The cameras default settings will be as shown below.

Shooting Settings

Shooting mode AF mode Metering mode Drive mode Exposure compensation AEB Flash exposure compensation Grid display P (Program AE) One-Shot AF Evaluative metering Single shooting 0 (Zero) Canceled 0 (Zero) Off

Image-Recording Settings

Record func. Image size JPEG quality ISO speed Picture Style Color space White balance WB correction WB-BKT File numbering File name setting Auto cleaning Dust Delete Data Standard L (Large) Standard sRGB AWB (Auto) Canceled Canceled Continuous Preset code Enable Erased
AF point selection Automatic selection
Live View shoot. Disable Custom Functions No changes

Camera Settings

Auto power off Beep Shoot w/o card Review time Highlight alert AF point disp. Histogram Enlarge display 1 min. On On 2 sec. Disable Disable Brightness Center
Image jump w/6 Auto rotate LCD brightness Date/Time Language Video system My Menu settings No changes No changes No changes No changes 10 images On zD
This chapter explains the settings for shooting digital images: Image-recording quality, ISO speed, Picture Styles, white balance, and color space.
When the camera is ready to shoot, you can press the <B> button to see the image settings. (p.186)
Setting the Image-recording Quality
You can set the image size (recorded pixels), image type (JPEG, RAW, sRAW), and JPEG quality (compression rate).

Selecting the Image Size

3/4/5/6 will record the image in the JPEG. In the 1/9 mode, the image will require processing with the software provided. 9 is a small RAW image which is one-fourth (approx. 2.5 megapixels) the size of a normal RAW image. Also, RAW/sRAW and JPEG images can be recorded at the same time on the memory card.

White Balance Auto Bracketing
With just one shot, three images having a different color tone can be recorded simultaneously. Based on the color temperature of the current white balance setting, the image will be bracketed with a blue/amber bias or magenta/green bias. This is called white balance bracketing (WB-BKT). White balance bracketing is possible up to 3 levels in single-level increments.
Set the white balance bracketing amount.
In step 2 for white balance correction, when you turn the <5> dial, the mark on the screen will change to (3 points). Turning the dial to the right sets the B/A bracketing, and turning it to the left sets the M/G bracketing. On the right side of the screen, BKT indicates the bracketing direction and the bracketing amount is also displayed. Press <0> to exit and return to the menu. To cancel the bracketing, set BKT to 0 ( becomes (1 point)).

B/A bias 3 levels

Bracketing Sequence
Correct white balance, blue (B) bias, and amber (A) bias. Or, correct white balance, magenta (M) bias, and green (G) bias.
During WB bracketing, the maximum burst for continuous shooting will be lower and the number of possible shots will also decrease to one-third the normal number. Also, the white balance icon will blink on the rear LCD panel. You can also set white balance correction and AEB together with white balance bracketing. If you set AEB in combination with white balance bracketing, a total of nine images will be recorded for a single shot. Since three images are recorded for one shot, the memory card will take longer to record the shot. BKT stands for Bracketing.
3 Setting the Color Space
The color space refers to the range of reproducible colors. With this camera, you can set the color space for captured images to sRGB or Adobe RGB. For normal images, sRGB is recommended.

Select [Color space].

Under the [1] tab, select [Color space], then press <0>.
the color space. 2 SetSelectdesiredor [Adobe RGB], then [sRGB]

press <0>.

About Adobe RGB
This is mainly used for commercial printing and other industrial uses. This setting is not recommended if you do not know about image processing, Adobe RGB, and Design rule for Camera File System 2.0 (Exif 2.21). Since the image will look very subdued with sRGB personal computer environment and printers not compatible with Design rule for Camera File System 2.0 (Exif 2.21), post-processing of the image with software will be required.
If the captured image was shot in the Adobe RGB color space, the first character in the file name will be an underscore _. The ICC profile is not appended. The ICC profile is explained in the Software Instruction Manual (CD-ROM).
Selecting the Media, Folder, and Recording Method

Metered Manual Flash Exposure
This is for close-up flash photography when you want to set the flash level manually. Use an 18% gray card and an EX-series Speedlite which has manual flash mode. Follow the instructions below: 1. Set the camera and Speedlite settings. Set the cameras shooting mode <a> or <f>. Set the Speedlite to manual flash mode. 2. Focus the subject. Focus manually. 3. Set up the 18% gray card. Place the gray card at the subjects position. In the viewfinder, the entire spot metering circle at the center should cover the gray card. 4. Press the <I> button. (8) 5. Set the flash exposure level. Adjust the Speedlites manual flash level and the camera aperture so that the flash exposure level aligns with the standard exposure index. 6. Take the picture. Remove the gray card and take the picture. If flash exposure compensation has already been set with the Speedlite, you cannot use the cameras <Q> button or Flash function settings menu to set flash exposure compensation. If it is set with both the camera and Speedlite, the Speedlites setting overides the cameras. If autofocus cannot be achieved, the external, EOS-dedicated Speedlites AF-assist beam (if the Speedlite has it) will be emitted automatically. If focus cannot be achieved with the external Speedlites AF-assist beam, select the center AF point. With some external Speedlites, autofocus with AF-assist beam works only with the center AF point. This camera is a Type-A camera that can use all the features of EXseries Speedlites.
Canon Speedlites other than the EX-series
With an EZ/E/EG/ML/TL-series Speedlite set in the TTL or A-TTL autoflash mode, the flash can be fired at full output only. Set the cameras shooting mode to manual or aperture-priority AE and shoot. When using a Speedlite which has manual flash mode, shoot with the manual flash mode. With an EX-series Speedlite set to TTL autoflash with the flashs Custom Function, the flash will fire at full output only.
Using Non-Canon Flash Units

Sync Speed

The camera can synchronize with compact, non-Canon flash units at 1/300 sec. (or 1/250 sec.) or slower shutter speeds. With large studio flash, the sync speed is 1/60 sec. or slower. Be sure to test the flash unit beforehand to make sure it synchronizes properly with the camera.

Possible Shots During Live View Shooting
Temperature Possible Shots At 23C / 73F Approx. 350 At 0C / 32F Approx. 250
* The figures above are based on a fully-charged LP-E4 battery and CIPA (Camera & Imaging Products Association) testing standards.

Image Playback

Learn how to view or erase images, and copy images between the CF card and SD card.
For images taken with another camera:
The camera might not be able to properly display images captured with a different camera or edited with a personal computer or whose file name was changed.

x Image Playback

Single image display

Playback the image.

Press the <x> button. The last captured image or last image viewed will appear.
2 Select the image. starting with the To playback images
last image, turn the <5> dial counterclockwise. To playback images starting with the first captured image, turn the dial clockwise. Press the <B> button to change the display format.
Single image display + Image size

Histogram display

Shooting information display
image playback. 3 Exit the the <x> button to exit the Press
image playback and return the camera to shooting ready.
Shooting Information Display Single image display + Image size
Protect Exposure compensation amount Aperture Shutter speed Sound recording Folder number - File number Memory card
Image-recording quality Playback image number/ Total images recorded
Shooting Information Display
Flash exposure compensation amount White balance correction Metering mode Shooting mode Color temperature if <P> is set Image-recording quality Playback image number/ Total images recorded White balance File size Picture Style AF microadjustment
Histogram (Brightness/RGB) ISO speed Picture Style settings Color space Date and time Original decision (image verification) data appended
About the Highlight Alert When the [4 Highlight alert] menu is set to [Enable], overexposed highlight areas will blink. To obtain more image detail in the overexposed areas, set the exposure compensation to a negative amount and shoot again. About the AF Point Display When the [4 AF point disp.] menu is set to [Enable], the AF point which achieved focus will be displayed in red in the shooting information display and histogram display. If automatic AF point selection was used, multiple AF points might be displayed in red. About the Histogram The brightness histogram display shows the exposure level distribution, overall brightness, and gradation. And the RGB histogram display is for checking the color saturation and gradation. The display can be switched with the [4 Histogram] menu. [Brightness] Display

K Sound Recording

You can add a sound clip to an image. The sound clip will be saved as a sound file (WAV format) having the same file number as the image. The sound can be played back with the provided software.
image to 1 Playback thethe sound which you want to add clip. sound. 2 Record theimage is displayed, press While the
the <H> button for about 2 sec. When [Sound recording] appears, keep pressing the button and speak into the built-in microphone. The maximum recording time for a sound clip is 30 sec. To end the sound clip, let go of the button. The sound will be recorded, and the < > icon will appear on the screen.

Microphone

The camera cannot playback the sound clip. Sound recording is not possible with a protected image. To record a sound clip longer than 30 sec., repeat step 2. You can also record sound once, right after image capture during the image review by following step 2.

a Copying Images

The images in a memory card can be copied to the other memory card.
Copying Individual Images

Select [Image copy].

Under the [3] tab, select [Image copy], then press <0>.
2 Select [Sel.Image].to select Turn the <5> dial
[Sel.Image], then press <0>.
folder. 3 Select the<5> dial to select the folder Turn the
containing the image to be copied, then press <0>. Refer to the images on the right to help you select the folder you want. The images in the selected folder will be displayed.

Total images selected

image. 4 Select the <5> dial to select the Turn the
image to be copied, then press <0>. The <X> icon will appear on the upper left of the screen. Press the <y> button to display the three-image view. To return to the single-image display, press the <u> button. To select another image to be copied, repeat step 4.
5 Press the <H > button. to be After selecting all the images
copied, press the <H> button.

Select [OK].

Check the target memory card and press <0>.
target folder. 7 Select the<5> dial to select the target Turn the
folder where the images are to be copied to, then press <0>. To create a new folder, select [Create folder].
8 Select [OK].copy source and copy Check the
targets information. Turn the <5> dial to select [OK], then press <0>.
The copying will start and the progress will be displayed. When the copying is completed, the result will be displayed. Select [OK] to return to the screen in step 2.
Copying All Images in a Folder
In step 2, select [Sel.n]. Select the source folder to be copied, then the target folder.
Copying All Images in a Memory Card
In step 2, select [All image]. All the folders and images in the source memory card will be copied to the target card. (The folder numbers and file names will remain the same in the target folder.)

C.Fn III -6

Lens AF stop button function
0: AF stop 1: AF start AF operates only while the button is pressed. While the button is pressed, AF operation with the camera is disabled. 2: AE lock When the button is pressed, AE lock is applied. Convenient when you want to focus and meter at different parts of the picture. 3: AF point: M 9 Auto/Auto 9 ctr In the manual AF point selection mode, the button instantly switches to automatic AF point selection (among 45 AF points) while you hold it down. Convenient when you are no longer able to focus track a moving subject with a manually-selected AF point in the AI Servo AF mode. You can instantly switch from manual to automatic AF point selection mode. In the automatic AF point selection mode, the button selects the center AF point only while you hold it down. 4: ONE SHOT z AI SERVO In the One-Shot AF mode, the camera switches to AI Servo AF mode only while you hold down the button. And in the AI Servo AF mode, the camera switches to One-Shot AF mode only while you hold down the button. Convenient when you need to keep switching between One-Shot AF and AI Servo AF for a subject which keeps moving and stopping. 5: IS start With the lens IS switch already <ON>, the Image Stabilizer operates when you press the button. 6: Switch to registered AF point While holding down the AF Stop button, press the <I> button to switch to the registerd AF point. If you do the same procedure again, the camera will return to the original AF point.
The AF stop button is provided only on super telephoto IS lenses. With setting 5, the Image Stabilizer will not operate when you press the shutter button halfway. To register the AF point, see page 171.

C.Fn III -7

AF Microadjustment
Normally, this adjustment is not required. Do this adjustment only if necessary. Note that doing this adjustment may prevent correct focusing from being achieved.
You can make fine adjustments of the AFs point of focus. It can be adjusted in 20 steps (-: Forward / +: Backward). The adjustment amount of one step varies depending on the maximum aperture of the lens. Adjust, shoot, and check the focus. Repeat to adjust the AFs point of focus. With setting 1 or 2 selected, press the <B> button to view the register screen. To cancel all the registered adjustments, press the <L> button. 0: Disable 1: Adjust all by same amount The same adjustment amount is applied to all lenses. 2: Adjust by lens An adjustment can be set individually for any particular lens. Adjustments for up to 20 lenses can be registered in the camera. When a lens whose focus adjustment has been registered is attached to the camera, its point of focus will be shifted accordingly. If adjustments for 20 lenses have already been registered and you want to register an adjustment for another lens, select a lens whose adjustment can be overwritten or deleted.

Auto power off is in effect. If you do not want auto power off to take effect, set the [5 Auto power off] menu to [Off].
No images can be shot or recorded.
The memory card is not properly inserted. (p.32) If the memory card is full, replace the card or delete unnecessary images to make room. Or if a not-full memory card is inserted in the other card slot, switch the recording to that card. (p.32, 73, 128) If you try to focus in the One-Shot AF mode while the focus confirmation light <o> in the viewfinder blinks, a picture cannot be taken. Press the shutter button halfway again to focus, or focus manually. (p.36, 86)
The LCD monitor does not display a clear image.
If dust is adhering to the LCD monitor, wipe with a lens cloth or soft cloth. In low or high temperatures, the LCD monitor display may seem slow or it might look black. It will return to normal at room temperature.
The image is out of focus.
On the lens, set the focus mode switch to <f>. (p.35) To prevent camera shake, hold the camera still and press the shutter button gently. (p.36, 40)
The memory card is unusable.
If a memory card error message is displayed, see page 48 or 193.
Live View shooting is not possible.
When using Live View shooting, use a memory card (a hard disk-type CF card such as MicroDrive is not recommended). A hard disk-type CF card requires a lower temperature range for operation than with normal memory cards. If the temperature gets too high, the Live View shooting may stop temporarily to prevent damage to the cards hard disk. When the cameras internal temperature decreases, the Live View shooting will be able to resume. (p.109)
Image Review & Operation
The image cannot be erased.
If the image has been erase-protected, it cannot be erased. (p.123)
The shooting date and time displayed is incorrect.
The correct date and time has not been set. (p.46)
No image appears on the TV screen.
Make sure the video cable plug is connected all the way in. (p.122) Set the video OUT format (NTSC/PAL) to the same video format as the TV. (p.44) Use the video cable that came with the camera. (p.122)

Error Codes

Error code

Countermeasures

If there is a problem with the camera, an error message appears. Follow the instructions displayed. To recover from the error, press the shutter button halfway, turn the power switch <2> and <1>, or remove and reinstall the battery. If error 02 (memory card problem) is displayed, remove and reinstall the memory card or format the card. This may resolve the problem.

Autofocus

TTL-AREA-SIR with a CMOS sensor 19 AF points (cross-type) and 26 Assist AF points (total 45 points) EV -1 - 18 (at 23C/73F, ISO 100) One-Shot AF (ONE SHOT), AI Servo AF (AI SERVO), Manual focusing (MF) AF point selection: Automatic selection (45 points), manual selection (19 points, 9 inner points, 9 outer points) Selected AF point display: Superimposed in viewfinder and indicated on top LCD panel AF-assist beam: Emitted by the dedicated external Speedlite Type: AF points: Metering range: Focus modes:

Exposure Control

Metering modes: 63-zone TTL full-aperture metering (1) Evaluative metering (linkable to any AF point) (2) Partial metering (approx. 13.5% of viewfinder at center) (3) Spot metering Center spot metering (approx. 3.8% of viewfinder at center) AF point-linked spot metering (approx. 3.8% of viewfinder) Multi-spot metering (Max. 8 spot metering entries) (4) Center-weighted average metering EV 0 - 20 (at 23C/73F with EF50mm f/1.4 USM lens, ISO 100) Program AE (shiftable), shutter-priority AE, aperturepriority AE, manual exposure, E-TTL II autoflash, flash metered manual
Metering range: Exposure control:
ISO speed (Recommended Exposure Index): 100 - 3200 (1/3-stop increments), expandable to ISO 50 and 6400 Exposure compensation: Manual: 3 stops in 1/3- or 1/2-stop increments (can be combined with AEB) AEB: 3 stops in 1/3- or 1/2-stop increments AE lock: Auto: Applied in One-Shot AF mode with evaluative metering when focus is achieved Manual: By AE lock button in all metering modes

Shutter

Type: Shutter speeds: Shutter release: Self-timer: Remote control: Electronically-controlled, focal-plane shutter 1/8000 to 30 sec. (1/3- and 1/2-stop increments), bulb, X-sync at 1/300 sec. (with EX series Speedlite for EOS cameras) Soft-touch electromagnetic release 10-sec. or 2-sec. delay Remote control with N3 type terminal

Drive System

Drive modes: Continuous shooting speed (Approx.): Max. burst: Single, High-speed continuous, Low-speed continuous, Self-timer (10 sec. and 2 sec), and Silent single shooting High-speed continuous: Max. 10 shots/sec., Low-speed continuous: Max. 3 shots/sec. JPEG (Large): Approx. 110, RAW: Approx. 30, RAW+JPEG (Large): Approx. 22 * Based on Canons testing conditions with a 1GB CF card for high-speed continuous shooting with JPEG quality 8, ISO 100, and Standard Picture Style. * Varies depending on the subject, memory card brands, imagerecording quality, ISO speed, drive mode, Picture Style, etc.

External Speedlite

Compatible flash: EX-series Speedlites Flash metering: E-TTL II autoflash Flash exposure compensation: 3 stops in 1/3- or 1/2-stop increments FE lock: Provided External flash settings: Flash function settings, Flash C.Fn settings PC terminal: Provided Zooming to match lens focal length: Provided

ICC profile.. 72 Image area.. 202 Image browsing (Jump display). 119 Image processing.. 54 Image protect. 123 Image-recording quality. 52 Image review time. 129 Image size.. 52 Image size automatic appending. 78 Image transfer.. 151 Index.. 148 Index display.. 119 INFO.. 114, 117, 186 Interface cable.. 138, 152 ISO speed.. 56 ISO speed increments. 158 ISO speed range (extension). 158
Green (G)..70, 145 Grid display..114
JPEG... 52 JPEG quality.. 55
Jump by 1 screen.119 Jump by 1/10/100 images.119 Jump by date..119 Jump by folder..119 Jump display..119
Landscape..57 Language..46 Large..52 LCD brightness..129 LCD monitor.13 LCD panel..13, 19, 20 LCD panel illumination.102 Lens..13, 35 Live View shooting.110 Long exp. noise reduction.163 Low level format..49 Low-speed continuous shooting..87
Metering mode. 90 MF.. 86 Mirror lockup.. 104, 172 Monochrome.. 58 Multi-controller.. 4, 38 Multi-spot metering.. 91 My Menu.. 181
Name (Caption).. 67 Natural.. 142 Neutral.. 57 New images.. points/9 points (inner/outer).. 170 Noise reduction.. 163 Nomenclature.. 16 Non-Canon flash. 108 NR.. 142 NTSC.. 44, 122
M (Manual)..98 Macro photography..104 Magenta (M)..70, 145 Magnified view..112, 120 Magnified view starting position.120 Main Dial..4, 37 Malfunction.190 Manual AF point selection..84 Manual exposure (M)..98 Manual focusing..86 Manual reset..80 Maximum burst..53, 54 Medium..52 Memory card (CF/SD).13, 32, 47, 73 Memory card slot cover.32 Menu Settings..43 Menus..41, 43
One-Shot AF.. 82 Original decision (image verification) data.. 178 Overwrite.. 127
P (Program). 92 Page layout.. 141 PAL... 44, 122 Paper settings.. 140 Partial metering.. 90 PC terminal.. 108 Personal white balance. 63 PictBridge.. 137 Picture Style.. 57 - 62 Playback.. 116 Playback menu.. 41, 43 Portrait.. 57
Possible shots.30, 53, 114 Power cord.22, 26, 31 Power source..26, 31, 47 Power Switch..36 Pressing completely.36 Pressing halfway..36 Print copies..143, 149 Print Order (DPOF)..137 Print settings..140 Printer errors..144 Printing effects..142, 145 Program AE (P)..92 Program Line..189 Program shift..93 Protect..123 Protect all images..123 Protecting all images in a card.123 Protecting all images in a folder.123 Protective cover..26
Release time lag. 177 Remote control terminal.. 103 Remote Live View shooting.. 109 Remote Switch.. 103 Replacing the date/time battery. 188 RGB display.. 118 Rotate.. 121, 130
Safety shift.. 160 Safety Warnings.. 10 Saving camera settings. 182 SD card. 13, 32, 47, 73 SD card slot. 32 Select all images. 149, 154 Select card.. 73 Select usable metering modes.. 160 Select usable shooting modes.. 160 Self Cleaning Sensor Unit. 131 Self-timer.. 88 Sensor cleaning. 131, 132, 135 Sepia... 60 Set.. 179 SET button.. 4, 41 SET button when shooting. 174 Set-up menu.. 41, 44 Shade.. 63 Sharpness.. 58 Shoot w/o card. 43 Shooting information display. 117 Shooting menus.. 41, 43 Shooting mode. 19 Shutter button.. 36 Shutter curtain sync.. 164 Shutter speed.. 94 Shutter speed range. 161 Shutter-priority AE (Tv). 94