Mark is a directive conformity mark of the European Community (EC).
This mark indicates that the product complies with Australias EMC regulations.

SAFETY PRECAUTIONS

Before using the camera, please ensure that you have read and understood the safety precautions described below. Always ensure that the camera is operated correctly. The safety precautions noted as follows are intended to instruct you in the safe and correct operation of the camera and its accessories to prevent injuries or damage to yourself, other persons and equipment. The term equipment refers primarily to the camera and its power supply accessories.

WARNINGS

Do not aim the camera or detached lens only directly into the sun or at other intense light sources that could injure your eyesight. Store this equipment out of the reach of children and infants. Accidental damage to the camera or batteries by a child could result in serious injury. In addition, placement of the neck strap around a childs neck could result in asphyxiation. Be particularly careful to keep the lithium battery CR2025 used in the camera out of the reach of children. Seek medical assistance immediately if a child swallows the battery. Do not attempt to disassemble or alter any part of the equipment. Disassembly or alteration may result in high-voltage electrical shock. Internal inspections, alterations and repairs should be conducted by qualified service personnel authorized by your camera distributor or Canon Customer Support. To avoid the risk of high-voltage electrical shock, do not touch internal portions of the equipment that become exposed as a result of damage. Please take the first opportunity to consult your camera distributor or Canon Customer Support immediately. Stop operating the equipment immediately if it should emit smoke or noxious fumes. Failure to do so may result in fire or electrical shock. Set the cameras main switch to the OFF position and remove the camera battery or unplug the power cord from the electrical outlet immediately. Please consult your camera distributor or the closest Canon Customer Support. Stop operating the equipment if it is dropped or the casing is damaged. Failure to do so may result in fire or electrical shock. Set the cameras main switch to the OFF position and remove the camera battery or unplug the power cord immediately. Please consult your camera distributor or the closest Canon Customer Support. Prevent the equipment from immersion in, water or other liquids. Do not allow liquids to enter the interior. The camera is not waterproof. If the exterior contacts with liquids or salt air, wipe it dry with a soft, absorbent cloth. If water or other foreign substances enter the interior, immediately set the cameras main switch to the OFF position and remove the camera battery or unplug the power cord immediately. Continued use of the equipment may result in fire or electrical shock. Please consult your camera distributor or the closest Canon Customer Support. Do not use substances containing alcohol, benzene, thinners or other organic solvent substances to clean or maintain the equipment. Do not cut, damage, alter or place heavy items on the power cord. Any of these actions may cause an electrical short circuit, which may lead to fire or electrical shock. Replace a broken or damaged power cord.

LCD Panel and LCD Monitor
(1) LCD displays are manufactured using high-precision technology. Even so, very small black, red, or green dots can occasionally appear on a display. This is within the normal 99.98% range for valid picture elements (pixels), and does not indicate a fault. Such aberrations on the display also do not affect recorded images. (2) Do not press hard on an LCD display or subject it to impacts, as this can cause display flaws and damage.
(3) If an LCD display becomes soiled, clean it with a commercially available blower brush, or wipe it with a soft cloth, taking care not to scratch the screen. If an LCD display becomes extremely soiled, consult your nearest Canon dealer. (4) By their nature, LCD displays react more slowly at low temperatures, and may appear dark at high temperatures. The display will return to normal at room temperature.
Lithium Battery for the Date and Time
(1) Store lithium batteries out of reach of small children. The chemicals in these batteries are very dangerous if the battery is accidentally swallowed. If this happens, seek medical attention at once. (2) Do not use metal instruments such as pliers to hold the battery, or you could cause a short circuit. (3) Do not disassemble or heat the battery, or you could rupture it.

CF Card

(1) The CF card is a precision device. Do not drop CF cards or expose them to vibrations. Doing so could lose the images recorded on them. (2) Do not store or use CF cards near objects that generate magnetic fields, such as TVs, speakers, or magnets, or in locations affected by static electricity. Doing so could lose the images recorded on the CF card. (3) Do not place CF cards in direct sunlight or close to heating appliances. Doing so can distort the cards and make them unusable. (4) Do not spill liquids onto CF cards. (5) Always store your CF cards in a case or cabinet to protect the data stored on them. (6) Use only CF cards specified by Canon. Otherwise, you may be unable to record or play back images. (7) Do not bend CF cards, or subject them to strong impacts. (8) Do not store CF cards in hot, dusty, or humid locations, or in locations exposed to static electricity or magnetic fields.

Lens Electrical Contacts

After detaching the lens from the camera, attach the lens caps or put down the lens with the rear end up to avoid scratching the lens surface and electrical contacts. Contacts

Quick Guide

Reference page numbers are indicated by ().

Charge the battery pack.

Connect the power cord to the adapter, then attach the battery. When the charge lamp stops blinking and stays lit, the battery is completely charged. A full battery charge takes approximately 90 minutes. (22)

Insert the battery pack.

Open the battery chamber cover and slide the battery pack into position until it locks into place. Press the cover closed until it clicks shut. (24)
Open the CF card slot cover.
Slide the cover in the direction shown by the arrow, then open it. (28)
Insert a CF card (optional).
After inserting the CF card, close the cover. (28) Using CF cards made by Canon is recommended.

Focus on the subject.

Look through the viewfinder and place the AF point over the subject. Then press the shutter button down halfway to focus. (29) The AF point which achieves focus will flash in red. In low-light conditions or backlit daylight conditions, the built-in flash fires automatically. (86)

Take the shot.

Press the shutter button down fully. (29)

Mount the lens.

Align the red dots on the lens and camera and turn the lens in the direction shown by the arrow in the diagram until it clicks into place. (27)
Set the focus mode switch on the lens to AF.

Turn on the camera.

Turn the main switch to <ON>. (29)
Set the Mode Dial to < (Full Auto).

Check the image.

The image is displayed for approximately 2 seconds after the shot. (40)
To check other images you have taken, see Check the Image Immediately (40) and Viewing Recorded Images (98). To erase images you have taken, see Erasing a Recorded Image (Single Image Erase) (43).

Nomenclature

DRIVE Drive mode selection button (63) Metering mode selection/ Flash exposure compensation button (61, 91)

LCD panel (16)

Main dial (30)
AF AF mode selection/White balance WB selection button (54, 66) Lens mount index (27) Built-in flash (86) Hot shoe (92)

Shutter button (29)

Flash button (86) Mode dial (18)

Strap mount (21)

Grip (Battery chamber) Lens release button (27)
DC coupler cord hole (26) Red-eye reduction/ Self-timer lamp (89, 81) AF-assist lamp (39) Mirror (84, 115) Depth-of-field preview button (73, 95)

Lens lock pin

Lens mount Electrical contacts (11)
DIGITAL terminal (See software instructions.)

VIDEO OUT terminal (112)

PC terminal (96) Remote control terminal
Eyecup (82) Viewfinder eyepiece Main switch (29)
Dioptric adjustment knob (36) Quick control dial switch (31) AE lock /FE lock button (80, 90) AF point selection button (57) Access lamp (28) Strap mount (21)
MENU Menu button (32) INFO. Info button (60, 100) JUMP Jump button (99) Index/ Enlarge button (98, 99)
Playback button (40, 98) LCD monitor (32) Erase button (43, 104) Tripod socket Date/time battery compartment cover (113) Set button (32) Quick control dial (31)

CF card slot cover (28)

Battery chamber cover release lever (24) Battery chamber cover (24)

CF Card Slot Cover

CF card slot (accepts card type1and 2) (28)
CF card eject button (28)

LCD Panel

Shutter speed ( , ) Data processing ( ) Date/time battery level warning ( Cleaning warning ( ) Parameters ( ) ISO Speed ( ) No CF card warning ( ) CF full warning ( ) CF error warning ( ) AF point ( ) Error cod ( - ) Cleaning ( ) )

Aperture value (

Drive mode Single-frame Continuous Self-timer Shots remaining ( - ) Self-timer countdown ( - ) Bulb exposure time ( ) ISO speed ( )
Quality Large/Fine Large/Normal Medium/Fine Medium/Normal Small/Fine Small/Normal RAW
AF mode ONE SHOT AF AI FOCUS AF AI SERVO AF
White balance mode Auto Daylight Cloudy Tungsten Fluorescent Flash Custom

Exposure level scale

Custom function Beeper
Exposure level Exposure compensation amount AEB level Flash exposure compensation amount CF card writing status Metering mode Evaluative metering Partial metering Center-weighted average metering AEB Manual focus
Battery check Red-eye reduction Flash exposure compensation
The above diagram shows the LCD panel with all icons and indicators displayed. In actual use, the items displayed differ according to the camera settings.

Viewfinder Information

New laser matte screen AF points (Superimposed display) Partial metering circle
AE lock/FE lock AEB in progress Flash-ready indicator FE lock underexposure warning

Focus confirmation light

Maximum burst count during continuous shooting ( - ) Shots remaining in CF card ( )
High-speed sync (FP flash)
Flash exposure compensation
Exposure level Exposure compensation amount AEB level Flash exposure compensation amount Red-eye reduction lamp-on indicator
Shutter speed ( FE lock ( ) Data processing (
CF full warning ( CF error warning ( No CF card warning (

Mode Dial

The Mode Dial is divided into two functional zones.

Creat ive zon e

Full Auto

1 Basic zone

All you do is press the shutter button. : Full Auto (38) Lets you take fully automatic picturesthe camera makes all the settings. Image zone Lets you take fully automatic pictures in specific situations. : Portrait (44) : Landscape (45) : Close-up (46) : Sports (47) : Night Portrait (48)

When the camera is ready to shoot, press the <INFO.> button to view the current camera settings on the LCD monitor.
Camera Setting Information
Auto power off time (29, 120) Review (41), Review time (42) Parameters (52)
C.Fn (Custom Function) number(s) (122) Flash exposure compensation (91) Shots remaining CF card capacity remaining (50) AEB (78) ISO speed (51)
Display the camera settings.
Press the <INFO.> button. The current camera settings appear on the LCD monitor. Press the < INFO.> button again to clear the LCD monitor.
For viewing image information during playback, see Turning the Information Display On and Off (100).
Selecting a Metering Mode
The EOS D60 uses three modes for metering: Evaluative, Partial, and Center-weighted average. The Basic Zone uses evaluative metering. In the Creative zone, any of the three modes can be selected.

Select a metering mode.

Look at the LCD panel as you turn the < > dial.
: Evaluative : Partial : Center-weighted average
Press the shutter button down halfway to return to ready-to-shoot mode.
Turn the < > dial to set the flash exposure compensation for the built-in/optional flash (91).

Metering Modes

: Evaluative Metering
This is an all-around metering mode suited even for backlit subjects. The viewfinder field is divided into 35 metering zones to which the three AF points are linked for evaluative metering. The camera determines the main subjects size, position, brightness, background, front and back lighting, etc., so that it can select the proper exposure for the subject at all times. When using manual focusing, evaluative metering is based on the center AF point.

: Partial Metering

This is particularly effective when the background is much brighter than the subject due to backlighting, etc. This method uses a center area of approximately 9.5% of the screen. The area covered by partial metering is shown on the left.
: Center-weighted Average Metering
This method meters the average exposure of the entire viewfinder screen, and gives extra weight to the center.

Selecting a Drive Mode

Illuminating the LCD panel
Press < >. To turn off the illumination, press < > again. If you operate a button or dial for picturetaking while the LCD panel is illuminated, the illumination will continue. If you press a menu or image playback button, the illumination will turn off.
If C.Fn-12-1/2/3 has been set, pressing < > will not turn off the LCD panel illumination (it will turn off automatically). If you take a picture while the LCD panel is illuminated, the illumination will continue as you shoot. LCD panel illumination works in all shooting modes.

Program AE

Like < > (Full Auto) mode, this is a generalpurpose picture-taking mode. The camera automatically sets the shutter speed and aperture value to suit the scenes brightness. This is called Program AE. stands for Program AE stands for Auto Exposure
Press the shutter button down halfway. The AF point achieving focus will flash in red and the beeper will sound. The focus confirmation light < > at the lower right will also light.
The shutter speed and aperture value are determined automatically, and displayed in the viewfinder and on the LCD panel. If the shutter speed and aperture values are not blinking, the exposure is correct. If either is blinking, see Exposure Warnings (132).
Compose the picture, then press the shutter button down fully.
Differences Between Program AE Mode < > and Full Auto Mode <
< > (Program AE) and < > (Full Auto) mode are alike in that both automatically determine the shutter speed and aperture values. The following functions can be used in < > mode but not in < > mode. AF mode selection Built-in flash firing manually/firing prohibited Manual AF point selection Flash exposure compensation Metering mode selection Special features with EX-series Speedlites Drive mode selection - High-speed sync (FP Flash) Program shift - FE lock AE lock with < > button - Flash output ratio control Exposure compensation - FEB Autoexposure bracketing (AEB) - 2nd-curtain sync Depth-of-field preview - Modeling flash Custom Functions

Shifting the Program

In Program AE mode, you can freely change the shutter speed and aperture value combination (program) set by the camera while maintaining the same exposure value. This is called shifting the program. > dial until the shutter To do this, press the shutter button down halfway, then turn the < speed or aperture value you want is displayed. Once you take a picture with the shifted program, the shifted program is canceled automatically and the original program is restored. If you are using a flash, you cannot shift the program.

Shutter-Priority AE

In this mode, you set the shutter speed, and the camera automatically sets the aperture value to suit the brightness of the subject. This is called Shutter-Priority AE. A fast shutter speed can freeze the motion of a fast-moving subject, and a slow shutter speed can blur the subject to give the impression of motion. stands for time value.

Fast shutter speed

Slow shutter speed

Set the shutter speed.

Press the shutter button down halfway. The aperture value is determined automatically.
Check the display, then take the picture.
If the aperture value is not blinking, the exposure is correct. Compose the picture, then press the shutter button down fully.
If the smallest aperture value (the maximum open aperture) for the lens you are using blinks, the scene is too dark. > dial to a slower shutter Turn the < speed until the aperture value stops blinking. If the largest aperture value (the minimum aperture) for the lens you are using blinks, the scene is too bright. Turn > dial to a faster shutter speed the < until the aperture value stops blinking.
Shutter Speed Display You can set the shutter speed in half-stop increments as shown below. The shutter speeds from 4000 to 4 indicate the denominator of the fractional shutter speed, so thatfor example125 is 1/125 second. For slow speeds, 07 is 0.7 seconds, and 15 is 15 seconds. 30
The ideal shutter speed for capturing a clear image from a TV screen is 1/15 second. We recommend using a tripod.
You can also set the camera so that you can set the shutter speed in 1/3-stop increments. (C.Fn-4-1122)

Aperture-Priority AE

In this mode, you set the aperture value, and the camera automatically sets the shutter speed to suit the brightness of the scene. This is called Aperture-Priority AE. By setting a smaller aperture value (larger aperture), you can blur the background to make the subject stand out as in a portrait. Or, by setting a larger aperture value (smaller aperture), you can increase the depth of field to make both the foreground and background look sharp. Av stands for aperture value.

Small aperture value

Large aperture value
Select the aperture value.
Press the shutter button down halfway. The shutter speed is determined automatically.

FE Lock

FE (flash exposure) Lock obtains and locks the correct flash exposure reading for any part of a subject. FE Lock is a function in the Creative zone.
Make sure the < > icon in the viewfinder is on.
In the Creative zone, press the < > button to pop up the built-in flash.
Focus on the subject you want to lock the flash exposure on.
Place the center AF point over the subject, and press the < >

button. (

The Speedlite fires a preflash and records the required flash output for this subject in memory. The < > icon lights in the viewfinder. The center AF point will flash in red. In the viewfinder, the display appears as shown in 1 for 0.5 seconds, then changes to 2. Each time you press the < > button the preflash fires, and the FE lock is applied at the required exposure level.
Compose the shot and take the picture.
If the subject is far enough away to cause underexposure, the < > icon will blink in the viewfinder. Move closer to the subject and repeat steps 2 4.
Flash Exposure Compensation
The EOS D60 camera can adjust the level of the built-in flash or any EX-series Speedlite. The compensation amount can be up to +/2 stops in 1/2-stop increments. You cannot use flash exposure compensation in the Basic Zone.

> button. (

Set the exposure compensation amount.
Set the Quick Control Dial Switch to <ON>. While looking at the LCD panel or viewfinder display, turn the < > dial. The [+] side indicates increased compensation, and the [] side indicates decreased compensation.
Once set, the exposure compensation amount remains in memory after the Main Switch is set to <OFF>. To cancel, set the compensation amount to the < > position.
Flash exposure compensation can also be set with EX-series Speedlites. If flash exposure compensation is set with both the camera and EX-series Speedlite, the Speedlite's setting will override the cameras.
You can set the camera to adjust exposure compensation in 1/3-stop increments. (C.Fn-4-1122) You can also disable the Auto reduction of fill flash function. (C.Fn-10-1124)
Flash Photography with the EOS-Dedicated 550EX Speedlite
The Canon 550EX Speedlite allows you to take high-quality flash pictures easily, in the same way as you would with a built-in flash.

E-TTL Autoflash

E-TTL autoflash (preflash evaluative metering in memory) supplies the correct level of flash for the subject in the AF point selected by AF. In dark locations, you can set the camera to aperture-priority AE for automatic slow-sync operation, for a natural-looking exposure balanced between the subject and background. High-Speed Sync (FP Flash) (94) High-speed sync (FP or focal-plane flash) enables flash synchronization at all shutter speeds from 30 sec. to 1/4000 sec. FE (Flash Exposure) Lock (95) FE lock obtains and locks the correct flash exposure for any part of the subject. This is the flash equivalent of AE lock. Flash Exposure Compensation (95) As with normal exposure compensation, you can use flash exposure compensation to adjust the flash output within a range of +/2 stops, in 1/2-stop increments. FEB (Flash Exposure Bracketing) (94) The FEB function is like AEB (autoexposure bracketing) with flash. You can bracket flash exposures by up to +/3 stops, in 1/2-stop increments. Modeling Flash (95) Modeling flash allows you to check shadows and the light balance produced by multi-light settings. Wireless Multi-Flash/E-TTL Autoflash (95) You can implement wireless multi-light E-TTL autoflash, using any or all of the features listed above. This provides the freedom to set up sophisticated lighting effects with no connection cords required.

Playing and Erasing Recorded Images
This section explains how to view the images you have recorded with the EOS D60, how to erase images, and how to make settings for Digital Print Order Format (DPOF) printers or photo lab printing services. This section also describes how to connect the EOS D60 to a television and how to set the date and time.
About Image Data Taken or Recorded by Other Devices
The EOS D60 may in some cases be unable to accurately display images taken with other cameras, or taken with the EOS D60 but subsequently had image data or file names modified by computer or other means.

About DPOF

DPOF (Digital Print Order Format) is a standard used to record (on the CF card or other recording media) the image number, number of prints, etc. of images taken by digital camera. You can simply insert the CF card into a DPOF-compatible printer to make prints as specified. You will not need to fill out the desired numbers and quantities of prints when ordering prints from a photo printing lab. This camera is compatible with DPOF Version 1.1.

Viewing Recorded Images

The EOS D60 can display recorded images on its LCD monitor. You can view these images in single-image format, index format, or enlarged format. Press the < > button to switch formats.

Viewing a Single Image

Viewing the Index
Press the < > button. The most recent single image taken by the camera appears. Press the < > button again to clear the LCD monitor and exit PLAY.
Turn the < > dial counterclockwise to view images in order from newest to oldest. Turn the < > dial clockwise to view images in order from oldest to newest.
This mode displays 9 images simultaneously on a single screen.
The most recent single image taken by the camera appears.

Display the index.

Press the < > button. The images are displayed in index format.
Change the image selection.
The selected image is surrounded by a green frame. Turn the < > dial counterclockwise to select images in order from newest to oldest. Turn the < > dial clockwise to select images in order from oldest to newest. Press the < > button to enlarge the selected image. To return to single-image display, press the < > button again. When you finish viewing, press the < > button.

Viewing Enlarged Images

Recorded images can be enlarged approximately 3.

Part to be enlarged

Select the image you want to enlarge from a single-image or index display. (98) Enlarge the image.
Press the < > button twice from a single-image display, or once from an index display. The selected image is enlarged approximately 3. The central part of the image is displayed first. An icon in the lower right part of the image indicates which part of the picture is currently displayed.

If the camera is set to the wrong video system format (121), you will not see a proper image on the TV set. Make sure the camera is set to the video system format (NTSC or PAL) compatible with the TV set. Using a DC coupler is recommended. (26) Images and menus do not appear on the LCD monitor while the video cable is connected to the camera. You can also switch the TV video signal to PAL (121). The default setting is for the NTSC signal standard.
Replacing the Date/Time Battery
will appear on the LCD panel. Replace When the date/time back-up battery level is low, the CR2025 lithium battery as follows. If you replace the backup battery while the camera is connected to a battery pack with power remaining or to a DC coupler, the date, time, and other menu functions will retain their settings.

(+) ()

Set the Main Switch to < OFF >.
Open the date/time battery chamber cover by turning it 45 degrees counterclockwise, as shown by the arrow in the diagram.
Be careful not to rotate the cover more than 45 degrees.
Take out the old battery.
With the camera bottom facing downward, push in the edge of the battery to take it out.

Install a new battery.

The plus side of the battery must face upward.
Close the cover by turning it clockwise, as shown by the arrow.
If the date and time now displayed in the LCD panel are incorrect, you will need to set them. (34)
For the date/time battery, be sure to use a CR2025 lithium battery.

File Numbering System

The pictures you take are automatically assigned file numbers from 0001 to 9900 and stored in folders of 100 images each. Each folder on the CF card is numbered from 100 to 998. Automatic file numbering can be either by continuous numbering or auto reset numbering (the default setting is continuous numbering):
3 images are recorded on the CF card
(1) Continuous: Numbering is continuous between cards, so that the first file number assigned on a new CF card is one more than the last file number assigned on the previous CF card. (2) Auto reset: Each time you insert a new CF card, the file number resets to its default value (Img_0001). If the card already contains files, the next available number is assigned.
Img_0001 Img_0002 Img_0003

Continuous numbering

Auto reset numbering
When you change the CF card and take a picture

Img Img_0004

Img Img_0001
From the menu, select [File numbering].
Press the < MENU> button. Turn the < > dial to select [File Numbering], then press the < > button.

Effective for preventing the effects of camera shake caused by mirror action in close-up and ultra-telephoto shots.
Effective in conditions that require more precise exposure settings. (The exposure indications may not change even if you change exposure settings. However, exposure control will be done according to your setting.) 134
AF-assist beam not emitted. Camera's built-in AF-assist beam not emitted. Flash not fired.

Func. No. 06

Item Shutter speed in Av mode with flash

Select no. 0 1

Setting or change Automatic setting Fixed at 1/200 second (when using flash)
AEB sequence / auto cancellaton
0 +/Enable 0 +/Disable 0 +/Enable 0 +/Disable 1st-curtain sync. Flash fires immediately after the shutter reaches full-open position. 2nd-curtain sync. Flash fires immediately before 2nd curtain closes. Stop AF while button is pressed Operate AF while button is pressed Press button to start AE lock The AF stop button is provided only on certain super telephoto lenses.

Shutter curtain sync

Lens AF stop button Fn. Switch
Auto reduction of fill flash

Enable Disable

C.Fn-8-1: This works with the built-in flash and EOS-dedicated Speedlites. However, if the Speedlite has a second-curtain sync feature, set the Speedlite for second-curtain sync.
Effects, remarks Effective for using flash at night or in dark locations

See page 73 93

The first AEB shot will be taken at the standard exposure. The AEB setting will be saved even when you turn off the main switch, change lenses, or replace the battery or CF card. The AEB shots will be taken starting with the decreased exposure. The AEB shots will be taken starting with the decreased exposure. The AEB setting will be saved even when you turn off the main switch, change lenses, or replace the battery or CF card.
Effective to capture movement of light sorce at slow shutter speeds.
Camera AF does not operate while this button is pressed. Effective for determining focus and exposure separately.
Produces natural daylight sync imaging. Prevents underexposure of people captured against strong backlighting such as sunsets.

Func. No. 11

Item Menu button return position
Setting or change Always show first menu item. Show the most recently set menu item. (Set the Main Switch to Off to cancel, or On to show the first menu item.) Show the most recently set menu item. (Retain in memory when the main switch is set to Off.) Default (no function) Change quality Change ISO speed Select parameters Disable Enable

The shutter speed and aperture value can be set in 1/3-stop increments. (C.Fn4122)

Message List

The following messages are displayed on the LCD monitor. Busy. No CF card CF card error. CF card full. Naming error! A picture is being stored on the CF card, or the camera is loading a recorded image. Attempted to take a picture or play an image with no CF card in the camera. There is a problem with the CF card. No more print orders can be stored. A file already exists with the file name that the camera is attempting to create. Or the file numbers have already reached the maximum value and no new file numbers can be created. Transfer the necessary number of images to a computer, then use the computer to format the CF card. Note that formatting will erase all images and information on the CF card. No images are recorded on the CF card. Attempted to play an image having a size larger than pixels. Attempted to play an image having a JPEG format that is not compatible with the camera. Attempted to play an image containing corrupted data. Attempted to rotate an image recorded by another camera or in another format, or processed by a computer. Attempted to play an image taken in a special format (such as a format unique to a camera from another manufacturer). Attempted to erase a protected image. Attempted to enter a print order quantity that is too high. Enter a lower quantity. Print order setting could not be stored. Playback of a CCDRAW image captured with a different camera was attempted.
No Image. Image too large. Incompatible JPEG format. Corrupted data. Cannot rotate Unidentified Image Protected! Too many marks. Cannot complete! CCDRAW

Error Codes

xx will be displayed on the LCD panel. Refer to the table below If a camera error occurs, to check what the error code means. If the same error occurs often, something is probably wrong with the camera. Jot down the xx error code and take your camera to the nearest Canon Service Center (back cover). If an error occurs after you take a picture, the camera might have missed the shot. Press the playback button to see if the image appears on the LCD monitor.
Clean the lens contacts. (11)
There is a problem with the CF card. Do one of the following: Remove and reinsert the CF card, format the CF card, or use another CF card.
The CF card is full. Delete unnecessary images or replace the CF card.
Something obstructed the built-in flashs pop-up operation. Turn off the main switch and turn it on again.
Either turn off the main switch and turn it on again or remove and reinsert the battery pack.

Troubleshooting

If you have a problem with your camera, first refer to this Troubleshooting Guide as you check the camera.
Unable to charge battery pack. An incorrect battery pack is being used. Use Battery Pack BP-511. (3) Battery pack is not correctly attached to the compact power adapter. Attach the battery pack correctly. (22) The DC coupler is connected to the compact power adapter. Remove the DC coupler plug from the compact power adapter. (23)

Power Source

Battery.. One Battery Pack BP-511 * AC power can be supplied via the DC coupler. Battery life.. Normal temp. Low temp. No flash use 620 shots 480 shots 50% flash use 490 shots 400 shots * The above figures apply when a fully-charged Battery Pack BP-511 is used. Battery check.. Automatic, displayed in one of three levels Power saving.. Provided. Power turns off after 1, 2, 4, 8, 15, or 30 min. Date/time battery.. One CR2025 lithium battery
Dimensions.. 149.5 (W) 106.5 (H) 75 (D) mm (5.89 4.19 3.0 in) Weight.. 780 g (27.5 oz) (excluding battery and CF card)
Dimensions and Weight Operating Conditions
Working temperature range.. 0C 40C Working humidity range. 85% or lower
Compatible battery. Battery Pack BP-511 Compatible coupler. DC Coupler DR-400 Battery connector. 2 (recharging disabled when the DC Coupler is installed) Power cord length.. Approx. 1.8 m / 5.9 ft. Recharging time.. Approx. 90 min. (per battery) Rated input. 100-240 VAC (50/60 Hz) Rated output.. During battery charging: 8.4 VDC With coupler connected. 8.1 VDC Working temperature range.. 0C 40C Working humidity range. 85% or lower Dimensions.. 100 (W) 51 (H) 133 (D) mm (3.94 2.0 5.24 in) Weight.. 285 g (10.1 oz) (excluding power cord)
Compact Power Adapter CA-PS400
Compatible adapter. Compact Power Adapter Canon-PS400 Compatible camera. EOS D60, EOS D30 Rated input. 6.3-10.5 VDC Rated output.. 6.3-10.5 VDC Cord length.. Approx. 1.8 m/ 5.9 ft. Working temperature range.. 0C 40C Working humidity range. 85% or lower Dimensions.. 38.4 (W) 21 (H) 55.3 (D) mm (1.51 0.83 2.18 in) Weight.. 110 g (3.9 oz) (excluding power cord) All Canon's testing Thethe specifications above are based on appearance are standards.change without notice. subject to camera's specifications and external

DC Coupler DR-400

Accessories.. 138 A-DEP... 76 AE.. 128 AEB (Autoexposure bracketing). 78 AE lock.. 80, 133 AF.. 27,128 AF Assist-beam.. 39 AF Mode.. 54 AF point... 57 AI Focus AF.. 56 AI Servo AF for moving subjects. 56 Aperture value.. 128 Auto power off function. 29, 120 Auto reset... 114 Av.. 72 DC coupler.. 19, 26 Depth of field.. 73, 128 Dioptric adjustment.. 36 Dioptric adjustment Lens.. 138 DPOF (Digital Print Order Format).. 97, 106, 129 Drive Mode... 63