USERS GUIDE GUA DEL USUARIO

AP31/33-ES-1

AP31/33_ES_cover.p65

Page 1

03.10.7, 11:00 AM

Adobe PageMaker 6.5J/PPC

427B-E-002A

Page 2

03.10.8, 11:35 AM
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS
WARNING When using electric products, basic precautions should always be followed, including the following: 1. 2. 3. 4. Read all the instructions before using the product. Heed all warnings. Follow all instructions. To reduce the risk of injury, close supervision is necessary when a product is used near children. Do not use this product near water for example, near a bathtub, washbowl, kitchen sink, in a wet basement, or near a swimming pool, or the like. This product should be used only with a stand that is specified by the manufacturer. This product, either alone or in combination with an amplifier and headphones or speakers, may be capable of producing sound levels that could cause permanent hearing loss. Do not operate for a long period of time at a high volume level or at a level that is uncomfortable. If you experience any hearing loss or ringing in the ears, you should consult an audiologist. The product should be located so that its location or position does not interfere with its proper ventilation. The product should be located away from heat sources such as radiators, heat registers, or other products that produce heat. 11. Do not defeat the safety purpose of the polarized plug. A polarized plug has two blades with one wider than the other. The wide blade is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 12. Unplug this product during lightning storms or when unused for long periods of time. 13. Care should be taken so that objects do not fall and liquids are not spilled into the enclosure through openings. 14. The product should be serviced by qualified service personnel when: A. The power-supply cord or the plug has been damaged; or B Objects have fallen, or liquid has been spilled into the product; or C. The product has been exposed to rain or moisture; or D. The product does not appear to operate normally or exhibits a marked change in performance; or E. The product has been dropped, or the enclosure damaged. 15. Do not attempt to service the product beyond that described in the user - maintenance instructions. All other servicing should be referred to qualified service personnel. 16. Clean only with dry cloth. 17. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the product. 18. Only use attachments/accessories specified by the manufacturer.
* 10 : applies to the AP-31V/AP-33V * 11 : applies to the AP-31/AP-33
10. The product should be connected to a power supply only of the type described in the operating instructions or as marked on the product.

KEEP THESE INSTRUCTIONS

427B-E-003B

Page 3

NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment.
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

427B-E-004A

Page 4

Introduction

Congratulations on your selection of the CASIO Digital Piano. This piano is a sophisticated musical instrument that blends the very best of traditional piano feel and sound quality with the latest that modern electronics technology has to offer. Before using the instrument, be sure to carefully read through the instructions contained in this manual. Please keep all information for future reference.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER -SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
CASIO ELECTRONICS CO., LTD. Unit 6, 1000 North Circular Road London NW2 7JD, U.K. This mark applies to the AP-31V/AP-33V only. Please keep all information for future reference.

427B-E-005B

AP31/33_E_01_09.p65

Safety Precautions

Symbols
Various symbols are used in this users guide and on the product itself to ensure that the product is used safely and correctly, and to prevent injury to the user and other persons as well as damage to property. Those symbols along with their meanings are shown below.

Symbol Examples

This triangle symbol ( ) means that the user should be careful. (The example at left indicates electrical shock caution.) This circle with a line through it ( ) means that the indicated action must not be performed. Indications within or nearby this symbol are specifically prohibited. (The example at left indicates that disassembly is prohibited.) The black dot ( ) means that the indicated action must be performed. Indications within this symbol are actions that are specifically instructed to be performed. (The example at left indicates that the power plug must be unplugged from the electrical socket.)

Avoid dropping the piano and other strong impact. Continued use of the piano after it has been damaged by dropping or by other external impact creates the risk of fire and electric shock. Immediately perform the following steps whenever the piano is damaged by impact. 1. Turn off piano power. 2. Unplug the piano from its power outlet. 3. Contact your original retailer or an authorized CASIO service provider. Do not put plastic bags over your head or in your mouth. Never allow the plastic bags that the piano and its accessories come in to be placed over the head or swallowed. Doing so creates the risk of suffocation. Special care concerning this point is required in households where there are small children. Opening and closing the keyboard cover Make sure that the keyboard cover is completely opened as far as it will go. When closing the keyboard cover, hold the front of the cover and close it slowly. Pinching your fingers between the piano and keyboard cover creates the risk of personal injury.

427B-E-008A

Power Cord Improper use of the power cord can create the risk of fire and electric shock. Always be sure to observe the following precautions. Never locate the power cord near a stove or other source of heat. When unplugging from an outlet, never pull on the cord. (Always grasp the plug when pulling.) After use turn off the power switch of the instrument and unplug the power cord from the electrical outlet. Power Plug Improper use of the power plug can create the risk of fire and electric shock. Always be sure to observe the following precautions. Push the plug fully into the power outlet as far as it will go. Unplug from the power outlet during lightening storms, and when you do not plan to use the piano for a long time (such as before a long trip). Unplug from the power outlet at least once a year and clean any dust build up between the prongs of the plug. Moving the piano Be sure to perform the following steps before moving the piano. Failure to do so can damage the power cord, creating the risk of fire and electric shock. 1. Unplug the piano from its power outlet. 2. Unplug the pedal connecting cord, and all cords and other items connected to the back of the piano.
Cleaning Before cleaning the piano, unplug it from the power outlet. Failure to do so can damage the power cord, creating the risk of fire and electric shock. It can also cause the piano to fall over, creating the risk of personal injury. Never climb onto the piano or stand. Doing so can cause the piano to fall over, creating the risk of personal injury. Special care concerning this item is required in households where there are small children. Connector Connect only the specified devices to the piano's connectors. Connecting non-specified items creates the risk of fire and electric shock. Location Avoid locating the piano in the following types of areas. Subjecting the piano to the conditions described below creates the risk of fire and electric shock. Areas expose to high humidity or large amounts of dust Near food preparation areas and other areas where it is exposed to oil smoke Near a heater, on a heated carpet, in direct sunlight, inside a closed automobile parked in the sun, and any other area subjected to very high temperature Never place the piano directly onto furniture or other item that has a finished surface. The rubber feet on the bottom of the piano can react with the paint or other coatings, resulting in soiling of or damage to the finished surface. Be sure to lay felt or some other material on the finished surface before placing the piano on it.

427B-E-009A

Page 5
Do not place heave objects on the piano. Never place heavy objects on top of the piano. Doing so can cause the stand to tip over and the object to fall, creating the risk of personal injury. Volume setting Do not play at very loud volumes for a long time. This precaution is especially important when using the headphones. Long-term exposure to very loud sound can damage your hearing. Assemble the stand properly. Failure to do so can cause the stand to fall over and the piano to fall from the stand, creating the risk of personal injury. Make sure your assemble the stand in accordance with the instructions that come with it, and ensure that all connections are secure. Also make sure that you choose an appropriate location for the stand. When placing the piano onto the stand, take care that you do not pinch your fingers between the piano and the stand. At least two people should lift the piano when placing it onto the stand or moving it. Trying to move the piano alone can cause the stand to fall over, creating the risk of personal injury. Do not drag the stand or tilt it forward or back when placing the piano onto the stand or moving it. Doing so can cause the piano to fall over, creating the risk of personal injury.
Periodically check the screws that secure the piano to the stand for looseness. If a screw is loose, retighten it. Loose screws can cause the stand to tip over and the piano to fall, creating the risk of personal injury.

427B-E-010A

Page 6

Operational Precautions

Locating the Unit
Avoid the following locations. Areas exposed to direct sunlight and high humidity. Areas subjected to very low temperatures. Near a radio, TV, video deck, or tuner (unit can cause interference with audio or video signals)

Care of the Unit

Never use benzene, alcohol, thinner or other such chemicals to clean the exterior of the unit. To clean the keyboard, use a soft cloth dampened with a weak solution of a mild neutral detergent and water. Wring out all excess moisture from the cloth before wiping. Severe impact can cause problems. When transporting the piano, use soft cloth to pack around the keyboard and buttons to protect them against damage. Never try to repair or modify any part of the piano. Any attempt to repair or modify the piano can cause problems with operation. Avoid using this piano near televisions, radios, etc. Because this piano uses digital circuitry, it may cause interference with other electronic devices such as televisions, radios, etc. In case of a problem, check that buttons and connections are correct, as indicated in this manual. If the piano still does not work properly, contact your retailer or a nearby dealer. Never try to repair the piano yourself.

Lithium Battery

This unit is equipped with a lithium battery to provide power needed to retain memory contents while unit power is turned off. Should the lithium battery go dead, all memory contents will be lost whenever you turn unit power off. The normal life of the lithium battery is five years from the time that the battery was installed. Be sure to periodically contact your retailer or authorized service provider to have the lithium battery replaced. Note that you will be charged separately for lithium battery replacement. Note that CASIO COMPUTER CO., LTD. shall not be held liable for any damages or losses or any claims by third parties arising from corruption or loss of data caused by malfunction or repair of the unit, or from battery replacement.
You may notice lines in the finish of the case of this piano. These lines are the result of the molding process used to shape the plastic of the case. They are not cracks or breaks in the plastic, and are no cause for concern.

NOTE

Unauthorized reproduction of this manual in its entirety or in part is expressly forbidden. All rights reserved. CASIO COMPUTER CO., LTD. shall not be held liable for any damages or losses or any claims by third parties arising from use of this product or this manual. The contents of this manual are subject to change without notice.

427B-E-011A

Page 7

Main Features

I 8 versatile tones
Eight instrument tones including piano and pipe organ provide plenty of performance versatility. Other features include digital effects that control the acoustical characteristic of tones, as well as three pedal effects for all the nuances of an acoustic piano.

I Metronome

A simple operation lets you set the tempo and the beat of the metronome to suit the tune you want to play. Its the perfect practice tool for players of all levels.

I 8 demo tunes

Eight demo tunes demonstrate how to use each of the built-in tones.

I Memory

Built-in memory lets you store a performance for later playback. You can play along with playback on the keyboard, and even create an ensemble effect by using a keyboard tone that is different from the recorded tone.
I Powerful keyboard setting functions
A selection of powerful keyboard setting functions help you get create exactly the musical mood you want. Transpose adjusts the key of the keyboard in semitone steps. Tuning provides a means to tune with another musical instrument. Touch Select adjusts the intensity of the output sound in accordance with the amount of pressure you apply to the keyboard.

I MIDI terminal

Connecting to another MIDI musical instrument lets you play two instruments from the keyboard of your CELVIANO. You can also connect to a commercially available MIDI sequencer to increase the number of parts you can play.

427B-E-012B

Page 8

Contents

IMPORTANT SAFETY INSTRUCTIONS Introduction. E-1 Safety Precautions.. E-2 Operational Precautions. E-7 Main Features.. E-8 Contents.. E-9 General Guide. E-10
Connecting Headphones..E-10 Attachment of the Score Stand.E-11

Keyboard Settings. E-19

Using Touch Select..E-19 Using Transpose..E-19 Adjusting the Tuning of the Piano. E-20

MIDI.. E-21

What is MIDI?..E-21 What you can do with MIDI..E-21 MIDI Connections.E-21 MIDI Channels...E-21 Simultaneous Receive Over Multiple Channels (Multi-Timbre). E-21 Setting the Keyboard Channel..E-22 Sending Memory Playback Data. E-22 Program Change Number Settings. E-23 Turning Local Control On and Off. E-24 MIDI Data Notes..E-25

Basic Operation.. E-12

Using Tones..E-12 Using the Pedals..E-14 Using the Metronome..E-15
Troubleshooting.. E-26 Assembly Instructions. E-27
Attachment of the Score Stand.E-29

Using the Memory. E-16

About the Memory..E-16 Recording..E-16 Playback...E-17 Deleting Memory Contents..E-17
Specifications. E-30 Appendix/Apndice. A-1
Initial Power On Settings.. A-1

Using Demo Tunes. E-18

MIDI Data Format.. A-2
Channel Messages. A-2 System Messages.. A-7
MIDI Implementation Chart

427B-E-013B

Page 9

General Guide

Key, button, and other names are indicated in the text of this manual using bold type. See page E-27 for details on the stand.

Headphones

IMPORTANT!
Whenever connecting headphone, first set the VOLUME knob of the CELVIANO and the volume controller of the external equipment to relatively low volume settings. You can later adjust volume to the level you want after connections are complete.

Headphone Jack

Connecting Headphones
Connect commercially available headphones to the CELVIANOs headphones jack. This cuts off the builtin speakers, which means you can practice even late at night without disturbing others. To protect your hearing, make sure that you do not set the volume level too high when using headphones.

GRAND PIANO 2 PIANO 1

PIANO 2
ELEC PIANO 2 HARPSICHORD ELEC PIANO 1 VIBRAPHONE OFF

REVERB STAGE

427B-E-022B

Page 18

Keyboard Settings

Using Touch Select
This setting lets you adjust the touch of the keyboard to suit your own playing style. This means you can select a stronger touch for those with powerful hands, and a lighter touch for beginners and anyone else with less strength. Use the keys shown below to change the Touch Select setting.

Using Transpose

Transpose lets you adjust the pitch of your CELVIANO in semitone steps. This means you can change the key of the piano to suit the voice of a vocalist or the key of another musical instrument, without having to learn to play a piece in another key. Use the keys shown below to change the transpose setting.

C4 (black key) C 4

E 4 (black key) D4

C5 F 5 F 4 (black key)

Touch Select Settings
C4. <OFF> C 4.. <LIGHT> This setting produces strong output, even when light pressure is applied to the keyboard. D4. <MIDDLE> This is the standard setting. E 4. <HEAVY> This setting requires relatively strong keyboard pressure to produce normal output.
To change the transpose setting
While holding down the CONTROL button, select a key by pressing one of the keyboard illustrated below.
C5: Standard key Lower Higher

(black key) F 4

To change the Touch Select setting
While still holding down the CONTROL button, select the key touch by pressing one of the keyboard keys illustrated below.

C 4 (black key): LIGHT

The transpose value is automatically set to 0 (C) whenever you turn on CELVIANO power.
C4 : OFF E 4 (black key): HEAVY D4 : MIDDLE
Touch select is automatically set to MIDDLE whenever you turn on CELVIANO power.

427B-E-023B

Page 19
Adjusting the Tuning of the Piano
You can adjust the overall tuning of the piano for play along with another instrument. You can adjust tuning within a range of 50 cents from A4 = 440.0Hz. Use the keyboard keys noted below to adjust the tuning of the piano.
F4: + (raises the pitch) E4: (lowers the pitch)
To adjust the tuning of the piano
Adjust the tuning as described below.
While holding down the CONTROL button, press keyboard key E4 () to lower the tuning or F4 (+) to raise it. Each press of a key changes the tuning by about 0.8 cents (1/128 semitone).
Holding down the CONTROL button and pressing keyboard keys E4 () and F4 (+) at the same time returns tuning to the standard A4 = 440.0Hz. * 100 cents is equivalent to one semitone.

427B-E-024A

Page 20

What is MIDI?

The letters MIDI stand for Musical Instrument Digital Interface, which is the name of a worldwide standard for digital signals and connectors that makes it possible to exchange musical data between musical instruments and computers (machines) produced by different manufacturers. MIDI compatible equipment can exchange keyboard key press, key release, tone change, and other data as messages. Though you do not need any special knowledge about MIDI to use your CELVIANO as a stand-alone unit, MIDI operations require a bit of specialized knowledge. This section provides you with an overview of MIDI that will help to get you going. *1 Keyboard play and memory playback data can be sent as MIDI data. Demo tunes cannot be sent as MIDI data. *2 A device that contains memory storage for MIDI data. Some MIDI sequencers feature external storage capabilities, which let you record a virtually unlimited number of tunes.

Acoustic Grand Piano Electric Piano 1 Harpsichord Strings Ensemble 1

427B-E-027B

Page 23
To change the program change number type
While still holding down the CONTROL button, select the Program Change Mode by pressing one of the keyboard keys illustrated below.

A 5 (black key): TYPE 1

Turning Local Control On and Off
This setting effectively determines whether or not the keyboard and pedals of the CELVIANO are connected to the CELVIANOs sound source, as illustrated below.

A5: TYPE 2

Keyboard Sound source ON Pedals OFF Local Control
A note does not sound when you press a keyboard key while holding down CONTROL. See the table on page E-23 for detailed information about Type 1 and Type 2.

General MIDI

The General MIDI System is a set of specifications for sound generating devices agreed upon by world MIDI manufacturers. These specifications were developed to allow the creation of music data that is not limited to specific equipment makers and models. Among other things, General MIDI defines the tone number sequence and the number of MIDI channels that can be used. Any device equipped with a sound source that supports General MIDI is able to produce sounds of similar nuances, regardless of the manufacturer or model. The Type 2 program change numbers of your CELVIANO assign program numbers to tones so they comply with the General MIDI System. Type 2 program change numbers make it possible to receive General MIDI System data from a connected sequencer or other device, and play it using the CELVIANOs tones. Tone switching is performed only when a program number that corresponds to any of the CELVIANOs non-bass tones is received. No tone switching is performed when any other program number is received. The table on page E-23 shows the program number assignments for Type 1 and Type 2. When Local Control is on (the normal setting), anything played on the keyboard is sounded by the internal sound source and simultaneously output from the MIDI OUT terminal. When off, anything played on the keyboard is output from the MIDI OUT terminal only, without being sounded by the sound source. Local Control can be turned off when you are using the CELVIANO as the sound source of a connected sequencer or other device, and you want to guard against sound being produced should the CELVIANO keyboard be pressed accidentally.
To turn Local Control on and off
While still holding down the CONTROL button, switch Local Control on and off by pressing one of the keyboard keys illustrated below.

F 5 (black key): OFF

G5: ON
Note that no sound will be produced from the CELVIANOs speakers if you press the keyboard while Local Control is turned off. Local Control is turned on automatically whenever you turn on CELVIANO power or play a demo tune.

427B-E-028A

Page 24

MIDI Data Notes

This section provides details about the MIDI data your CELVIANO sends and receives. You can also find further technical information in the MIDI Data Format and MIDI Implementation Chart* at the end of this Users Guide. * The MIDI Implementation Chart is a standard format summary of how data is transferred between your CELVIANO and a connected MIDI device.
Keyboard Data (Note On, Note Off, Note Number, Velocity)
The following four types of keyboard data can be sent and received. Data Note On Note Off Note Number Velocity Meaning Keyboard key is pressed. Keyboard key is released. Which key is pressed. Pressure applied
Tone Change Data (Program Change)
Whenever you change the tone on the CELVIANO, tone change data (Program Change) is also sent out as MIDI data. Conversely, receipt of a Program Change from a connected MIDI device causes the CELVIANO to change to the applicable tone. See Program Change Number Settings on page E-23 for details.
Pedal and Effect Operation Data (Control Change and Universal System Exclusive Message)
Control Change is used to send and receive data about damper, soft, and sostenuto pedal* depress and release, as well as data about digital effects. * AP-31 Users The AP-31 is equipped with only two pedals. The left-hand pedal can be switched between soft and sostenuto. The pedal effect applied by MIDI data depends on whether data is being sent or received. Send: Pressing the left pedal sends data that corresponds to the current pedal effect setting (soft or sostenuto). Receive: Pedal effect is applied in accordance with the data received.

427B-E-029B

Page 25

Troubleshooting

Symptom
No sound produced when keyboard keys are pressed.

Possible Cause

1. VOLUME knob set to MIN. 2. Headphones connected to the piano. 3. Local Control turned off.

Action

1. Move VOLUME knob more towards the MAX side. 2. Disconnect the headphones from the piano. 3. Turn on Local control. 1. Change the transpose setting to 0, or turn CELVIANO power off and then back on again. 2. Correct the tuning setting, or turn CELVIANO power off and then back on again. Turn off CELVIANO power and then check to make sure that the pedal plug is securely connected to the pianos pedal connector. 1. Move VOLUME knob more towards the MAX side. 2. Disconnect the headphones from the piano. Contact your CASIO Service Provider for replacement of the lithium battery. 1. Change the Keyboard Channel settings so they are identical. 2. Change the volume or expression setting of the external sound source to an appropriate value.

Pedal plug Clip J

Attachment of the Score Stand
Install the music stand by inserting its pegs into the holes in the top of the piano.
Position the pedal plug as shown in Figure 8 and insert it into the pedal connector on the bottom of the piano. Secure the pedal cable to the upright of the stand using the J clips that you installed when assembling the stand (Figure 8).
4 Connecting to a Power Supply

Figure 9

Power cord

Household wall outlet

1. Check to make sure that the pianos POWER button is in the OFF position. If it is ON, press the button to switch it OFF. 2. Attach the power cord that comes with the piano to the bottom of the piano.* 3. Plug the pianos power cord into a wall outlet (Figure 9). * 2: applies to the AP-31V and AP-33V
The shapes of the pianos power cord and wall outlet should be different according to countries or regions. The illustrations are examples. With the AP-31 and AP-33, the power cord is hard-wired to the bottom of the instrument.

427B-E-033B

Page 29

Specifications

All of the items in these specifications apply to the AP-31, AP-31V, AP-33, and AP-33V, unless specifically noted otherwise. Models: Keyboard: Polyphony: Tones: Digital Effects: Demo Tunes: Memory: AP-31/AP-31V/AP-33/AP-33V 88 piano keys (with touch response) 64 notes, maximum 8 Reverb (4 types), Chorus Number of Tunes: 8 Playback: Repeat (all tunes, one tune) Operations: Real-time recording, playback Capacity: Approximately 2,500 notes (one song) Memory Backup: Built-in lithium battery (Battery Life: 5 years) Pedals: Other Functions: AP-31/AP-31V: Damper, Soft/Sostenuto (Selectable) AP-33/AP-33V: Damper, Soft, Sostenuto Metronome: Beat (6 types), Tempo ( = 30 to 255) Touch Select: 3 types, off Transpose: 1 octave (F to C to F) Tuning: A4 = 440Hz 50 cents (adjustable) MIDI: Input/Output: 16 multi-timbre receive Headphones: Stereo standard jacks 2 Output Impedance: 470 Output Voltage: 18V (RMS) MAX MIDI (OUT) (IN) Speakers: Power Supply: Power Consumption: Dimensions: Weight: 12cm 2 (Output: 20 W + 20 W) AP-31/AP-33: 120V AP-31V/AP-33V: 220-240V AP-31/AP-33: 60W AP-31V/AP-33V: 60W CELVIANO (without stand): 137.0 42.5 19.0 cm (53 15/3/1/2 inch) CELVIANO: 139.0 47.0 81.0 cm (54 3/1/7/8 inch) CELVIANO (without stand): approximately 34 kg (74.8 lbs) CELVIANO: approximately 44 kg (96.8 lbs) (AP-31/AP-31V) approximately 44 kg (96.8 lbs) (AP-33/AP-33V) Design and specifications are subject to change without notice. AP-31 and AP-33 have hardwired power cords. AP-31V and AP-33V have detachable power cords.

n. Voice Channel Number = 0H to FH (Ch1 to Ch16) pm. MSB of NRPN pl.. LSB of NRPN Recognition NRPN messages not defined by the instrument can also be received, but subsequent data entry values after undefined NRPN messages are ignored. After the NRPN MSB and LSB are received and the applicable control parameters settings are made, the value is set by receipt of the MSB of the subsequent data entry. The data entry LSB is ignored.

Portamento Control #

Format Byte 1 BnH Byte 2 54H Byte 3 kkH
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) kk. Source Note Number = 00H to 7FH
Effect 1 Depth (Reverb Send Level)
Format Byte 1 BnH Byte 2 5BH Byte 3 vvH

Vibrato Rate

NRPN MSB = 01H NRPN LSB = 08H Data Entry MSB = mmH mm. Vibrato Rate = 00H to 40H to 7FH (-64 to 0 to +63) Recognition When the instrument receives this message, the preset Vibrato Rate value for the tone is changed to the Vibrato Rate value that corresponds to the data entry MSB of the received message. There is no change when the value of the data entry MSB is 40H(0).
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) vv. Reverb Send Level = 00H to 7FH
Effect 3 Depth (Chorus Send Level)
Format Byte 1 BnH Byte 2 5DH Byte 3 vvH

Vibrato Depth

NRPN MSB = 01H NRPN LSB = 09H Data Entry MSB = mmH mm. Vibrato Depth = 00H to 40H to 7FH (-64 to 0 to +63) Recognition When the instrument receives this message, the preset Vibrato Depth value for the tone is changed to the value that corresponds to the data entry MSB of the received message. There is no change when the value of the data entry MSB is 40H(0).
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) vv. Chorus Send Level = 00H to 7FH
NRPN (Non-Registered Parameter Numbers) #
With the instrument, NRPN are defined as tone editing parameters and drawbar parameters. The MSB and LSB of an NRPN specify the parameter being controlled, while the specified parameters value is set in accordance with the subsequent data entry. The following table shows the relationship between parameters and NRPN as defined by the instrument. NRPN MSB NRPN LSB 01H 08H 01H 09H 01H 0AH 01H 20H 01H 21H 01H 63H 01H 01H 64H 66H Parameter Vibrato Rate Vibrato Depth Vibrato Delay TVF Cut Off Frequency TVF Resonance TVF/TVA Envelope Attack Time TVF/TVA Envelope Decay Time TVF/TVA Envelope Release Time

Vibrato Delay

NRPN MSB = 01H NRPN LSB = 0AH Data Entry MSB = mmH mm. Vibrato Delay = 00H to 40H to 7FH (-64 to 0 to +63) Recognition When the instrument receives this message, the preset Vibrato Delay value for the tone is changed to the value that corresponds to the data entry MSB of the received message. There is no change when the value of the data entry MSB is 40H(0).

Reset All Controller #

Format Byte 1 BnH Byte 2 79H Byte 3 00H
n. Voice Channel Number = 0H to FH (Ch1 to Ch16)

Program Change

Format Byte 1 CnH Byte 2 ppH
Recognition Receipt of the Reset All Controller message causes the following controllers to be reset. Controller Name Modulation Wheel Expression Controller Hold 1 Portamento Sostenuto Soft NRPN RPN Pitch Bend Change Reset Value vvH = 00H vvH = 7FH vvH = 00H vvH = 00H vvH = 00H vvH = 00H msb = 7FH, lsb = 7FH msb = 7FH, lsb = 7FH llH mmH = 00H 40H
pp. Program Number = 00H to 7FH Send Program Change messages are sent when you select a tone on the instrument.

427B-E-070B

All Note Off
Format Byte 1 BnH Byte 2 7BH Byte 3 00H

Poly Mode On #

Format Byte 1 BnH Byte 2 7FH Byte 3 00H
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) Recognition Receipt of the All Note Off message mutes all tones being played by data received over the MIDI channels (note off). If Hold 1 or Sostenuto is turned on when the All Note Off message is received, notes are sustained in accordance with the corresponding pedal operation. Send This message is sent when the CONTROL button is pressed and when memory playback is stopped.
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) Receive Receipt of a Poly Mode On message by the instrument sets Channel n to Mode 3 and is processed as if an All Sound Off message and All Note Off message were received.

System Messages

Universal System Exclusive Message

GM System On #

Format F0H 7EH 7FH 09H 01H F7H

Omni Mode Off #

Format Byte 1 BnH Byte 2 7CH Byte 3 00H
Send This message cannot be sent.
n. Voice Channel Number = 0H to FH (Ch1 to Ch16) Recognition Receipt of an Omni Mode On message does not turn on the instrument Omni Mode. Receipt of an Omni Mode On message is treated as an All Note Off message.

Reverb Type

Format F0 7F 7F vv F7 Parameter (vv) 00H 02H 03H 04H Setting ROOM STAGE HALL 1 HALL 2 GM Level 2 Equivalent Small Room Large Room Medium Hall Large Hall

Omni Mode On #

Format Byte 1 BnH Byte 2 7DH Byte 3 00H

Chorus Type

n. Voice Channel Number = 0H to FH (Ch1 to Ch16) Recognition Receipt of an Omni Mode On message does not turn on the instrument Omni Mode. Receipt of an Omni Mode On message is treated as an All Note Off message. Format F0 7F 7F vv F7 Parameter (vv) 02H Setting GM Level 2 Equivalent CHORUS Chorus 3

Mono Mode On #

Connecting to a Musical Instrument Amplifier
Use commercially available cables to connect the amplifier to the pianos LINE OUT jacks as shown in Figure. LINE OUT R jack output is right channel sound, while LINE OUT L/MONO jack output is left channel sound. Connecting to the LINE OUT L/ MONO jack only outputs a mixture of both channels. It is up to you to purchase connecting cable like the one shown in the illustration for connection of the amplifier. Use the pianos VOLUME controller to adjust the volume level.

Using Built-in Tones

8METRONOME blMUSIC LIBRARY brTONE btw, q bsFUNCTION ctCHORUS, u dkSPLIT, i dlENTER csREVERB

7PART bkTEMPO

Tone groups
Turning on the Digital Piano and Playing Something

Selecting a Tone

Your Digital Piano has 250 tones, divided into eight groups. For more information, see the Tone List (page A-1). The Digital Piano has built-in demonstration tunes that highlight the different characteristics of tones. For more information, see Playing Back All of the Built-in Songs (page E-23).
Press the (POWER) button.
This turns on power. To turn off the Digital Piano, press the button again.

Left Side

button
Press the (TONE) button so its upper lamp is lit.
Each press of the button toggles between the upper and lower lamps.
After a short while, the display screen should appear as shown below, which indicates that the Digital Piano is ready to be played.
Continuing on to the next step while the REGISTRATION lamp is lit will perform a registration recall operation (page E-32), which will change the setup of the Digital Piano. Make sure that the TONE lamp is lit before you advance to the next step.
Use the (VOLUME) controller to adjust the volume level. Play something on the keyboard.
Use the Tone List (page A-1) to look up the group and the number of the tone you want to select.
Use the to (tone groups) buttons to select the group you want.
Example: To select the ORGAN group
This will layer the tones currently selected in the two groups.
Use the (w, q) buttons to select the tone you want.
Example: To select 002 Jazz Organ

Tone number Tone name

The button you held down in step 2 will light to indicate that it is selected. Example: When BASS/GUITAR group is selected

Adjusting the Metronome Volume
You can use the following procedure to adjust the volume level of the metronome, without affecting the volume of Digital Piano output.
To adjust the tempo using q and w buttons
While holding down the (FUNCTION) button, press the (METRONOME) button.
This displays the metronome volume screen.
Use the (TEMPO w, q) buttons to adjust the tempo setting.
Each press of a button increases or decreases the beats per minute value by one. Holding down either button changes the value at high speed. You can specify a tempo value in the range of 20 to 255.

Metronome volume

Tempo value
Use the (w, q) buttons to adjust the metronome volume. Press the (FUNCTION) button.
This will exit the metronome volume screen and cause the FUNCTION lamp to go out.
To adjust the tempo by tapping a beat
While holding down the (FUNCTION) button, tap the q (TEMPO) button four times in time with the beat you want to specify.
The tempo setting will change in accordance with the timing of your tapping. After you use this method to specify the approximate tempo, you can then use the procedure under To adjust the tempo using q and w buttons to adjust the setting to a more exact value.

Tap four times

You also can use the procedure under Metronome Volume (page E-41) to adjust the metronome volume.

Playing a Duet

You can use the Duet Mode to split the Digital Pianos keyboard in the center so two people can play a duet. This makes it possible to configure the keyboard so, for example, the teacher can play on the left and the student can follow along on the right. Or one person can play the left hand part on the left, while another plays the right hand part on the right.
Left keyboard Right keyboard

(Middle C)

Pedal Operation when Playing a Duet
Left keyboard damper pedal
Right side damper pedal (Half-pedal operation supported)
Left and right side damper pedal
Configuring the Digital Piano for Duet Play
Changing the Octave of a Duet Mode Keyboard
You can use the following procedure to change the octave of the left and right Duet Mode keyboards.
Press the (MUSIC LIBRARY) button so its lower lamp is lit.
While holding down the (FUNCTION) button, press the (SPLIT) button.
This displays the Duet Mode on/off screen shown in step 2 under Configuring the Digital Piano for Duet Play (page E-15). If the Duet Mode is currently turned off, press the (q) button to turn it on.

This will start sequential playback of the tone demo songs, starting from song 1.

Song number Song name

Current measure Song tempo
Pressing a tone group button (buttons through ) while demo song playback is in progress will switch to the demo song that uses the tones of that group. Pressing a Music Library song group button (buttons through , Group A through C) while demo song playback is in progress will switch to playback of the songs in that group. Pressing the (CARD/INTERNAL) button during demo song playback will start playback of the songs on the loaded card. For details, see Playing Back All of the Songs in a Folder (page E-48).

blMUSIC LIBRARY

btw, q

dlCARD/INTERNAL

Playing Back a Specific Music Library Song
You can use the procedure below to select a Music Library song for listening or practice. The Music Library has a total of 60 songs, divided into three groups (A, B, C). You also can load songs from a memory card or your computer into a fourth Music Library group (Group D) for playback and practice (pages 46 and 52).
This starts playback of the song. Press the (FF) button to perform a fast forward operation or the (REW) button for rewind. Pressing and releasing either button moves one measure, while holding down a button scrolls at high speed. Pressing the (PAUSE) button pauses playback. Press again to resume song playback.
Lights with each subsequent beat of each measure Lights with the first beat of each measure
Press the (MUSIC LIBRARY) button so its lamp is lit.
Rewind Fast forward Pause
Press the (PLAY/STOP) button again.
This stops song playback. Song playback also will stop automatically when the end of the song is reached. To configure the Digital Piano to loop song playback without stopping, turn on Song Repeat (page E-42).
In the Song List (page A-6), find the group and group number of the song you want.
User songs are in Group D.

Changing the Song Tempo

You can change the song tempo using the same procedure that you use to adjust the metronome tempo. For more information, see Changing the Tempo Setting (page E-14).
Use the to (Song group A to D) buttons to select the group you want. Press button (Group D) if you want to select a user
song. Example: When Group B is selected
Playing on the Keyboard Using the Same Tone as the Song
Hold down the (MUSIC LIBRARY) button for at least two seconds.
This will assign the same tone as the right hand part of the current song to the keyboard.
Use the (w, q) buttons to select the song you want.
Example: When 008 Gavotte is selected
You can use the procedure under Practicing Either Hands Part (Part Off) (page E-25) to turn off the left hand part and play along on the keyboard using the left hand part tone.

Initialize (Initialize)

Change Key (Change Key)
Use the (w, q) buttons to select the amount of change you want (5 to 6 semitones). Use the (w, q) buttons to select the number of the Music Preset you want to add. Use the (w, q) buttons to select the measures.
Append Music Preset (Append Chords) Delete Measures (DELETE Measure) Insert Measure (INSERT 1Measure)
* The Music Presets in groups B, C, and D are numbered sequentially, following the numbers in group A, which start with 001. For details about sequential numbers, see the Music Preset List on page A-7.
After all editing operations are complete, press the (EXIT) button to return to the editing operation selection screen (page E-27).
A single preset can contain up to approximately 2,000 chords. If your edits cause the chord limit to be exceeded, the message Memory Full will appear on the display and further editing will become impossible.
To edit Auto Accompaniment parameters
Use the (u) and (i) buttons to select a parameter, and the (w, q) buttons to change its setting.
Parameter SYNCHRO TYPE: Synchro type DRUM ON/OFF: Drum on/off PERC ON/OFF: Percussion on/off BASS ON/OFF: Bass on/off Description Selects the synchro standby status and type when the Music Preset is selected. Setting 0 Off: Off (no standby) 1 Normal: From standby to normal pattern 2 Variation: From standby to variation pattern 3 Intro: From standby to intro pattern OFF: Mutes the part. ON: Sounds the part. OFF: Mutes the part. ON: Sounds the part. OFF: Mutes the part. ON: Sounds the part. OFF: Mutes the parts. ON: Sounds the parts. C - B: Major (C to B) Cm - Bm: Minor (Cm to Bm) C - B: Major (C to B) Cm - Bm: Minor (Cm to Bm) OFF: Fill-in not inserted ON: Fill-in inserted
Toggles the drum part (page E-21) on or off. Toggles the percussion part (page E-21) on or off. Toggles the bass part (page E-21) on or off. Toggles the Chord 1 through 5 parts (page E-21) on or off. Selects from among major ( 12 keys) and minor ( 12 keys) for the intro chords. Selects from among major ( 12 keys) and minor ( 12 keys) for the ending chords. Specifies whether or not a fill-in should be inserted into the final measure of a chord progression.
CHORD1 - - 9 ON/OFF: Chord 1 - 5 on/off INTRO CHORD: Intro chord ENDING CHORD: Ending chord AUTO FILL-IN: Auto fill-in on/off
TIMING SET: Chord progression variation
1 Normal: Edited chord progression proceeds as-is. This parameter lets you add different 2 Half: Halves chord timing within a measure. variations to the timing of the chord 3 Double: Doubles chord timing within a progression being edited. You can use it to measure. match the chord progression to the beat of a 4 3/4: Multiplies chord timing within a measure specific rhythm. by 3/4. Select this setting to match to a A chord (step) that is outside of the rhythms 6/8 time rhythm. beat is cut off. 5 6/4: Multiplies chord timing within a measure by 3/2. Select this setting to match to a 6/4 time rhythm.

The file number is the final two characters of the file name* that appears on the display. By changing this within the range of 01 to 99 for each save, up to 99 files of the same data type can be stored on the memory card. * The first six characters of the file name indicate the data type as shown below. These characters are fixed and cannot be changed.
Loading Data from a Memory Card
You can use the procedure below to load data from a memory card into Digital Piano memory.
Data Type User rhythms User Music Preset Recorder songs Registrations
File Name (** = file number) USRRHY** USRMPS** RECSNG** REGIST**
Make sure that all of the data you want to load is in the MUSICDAT folder on the memory card. Note that if you put data into a music data play-only folder on a memory card (such as the MUSIC__B folder), you will no longer be able to load that file into Digital Piano memory.
Insert the memory card into the Digital Pianos memory card slot. Select the data you want to load.
Do this: Select from among user rhythms 001 through 010 (page E-20). Select from among user songs 001 through 010 (page E-24). Select from among user Music Presets 001 through 050 (page E-27).
The message Please Wait will remain on the display while the save operation is being performed. Do not perform any Digital Piano operation while this message is on the display. Complete appears on the display after data save is complete. If there already is a file with the same name on the memory card, a message (Replace?) will appear asking if you want to replace it with the new data. Press the (YES) button to replace or the (NO) button to cancel the save operation.
To load this type of data* User rhythms User songs User Music Preset
Recorder songs Select from among recorder songs 1 through 5 (page E-34). Registrations Press the (REGISTRATION) button so its lower lamp is lit.

Memory Card Data Storage

The above procedure stores Digital Piano data in a folder named MUSICDAT on the memory card. The MUSICDAT folder is created automatically when you format the memory card on the Digital Piano (page E-45). Note that files not in the MUSICDAT folder cannot be loaded, deleted, or renamed by this Digital Piano. You also will not be able to load or delete any file stored in any subfolder inside the MUSICDAT folder.

* For more information about data types, see page E-43.
Use the (w, q) buttons to select the file you want. Press the (ENTER) button.
The message Please Wait will remain on the display while the load operation is being performed. Do not perform any Digital Piano operation while this message is on the display. Complete appears on the display after data loading is complete. If there is already data in the destination you are loading to, a message (Replace?) will appear asking if you want to replace it with the new data. Press the (YES) button to replace or the (NO) button to cancel the load operation.
Deleting Memory Card Data
Use the following procedure to delete memory card data (files).
Renaming a Memory Card File
Use the following procedure to change the file name of a file on a memory card.
Insert the memory card into the Digital Pianos memory card slot. While holding down the (FUNCTION) button, press the (CARD/INTERNAL) button.
This displays the memory card format screen (page E-45).

3. 4. 5. 6. 7.

This displays the file delete screen.

3. 4. 5. 6.

Press the button (i) twice so File RENAME is displayed. Press the (ENTER) button.
This displays a screen for changing the file name.
This displays a screen for selecting data for deletion.
This will display a confirmation message (SURE?). If you want to cancel the delete operation, press the (NO) or (EXIT) button.
Use the (w, q) buttons to select the file you want. Use the (i) and (u) buttons to move the flashing cursor to the character you want to change, and then use the (w, q) buttons to change the character.
The characters you can select are shown below.
The message Please Wait will remain on the display while the delete operation is being performed. Do not perform any Digital Piano operation while this message is on the display. Complete appears on the display after deletion is complete.

0 A K U (

3 B C D L M N V W X ) - ^

4 E O Y {

F G P Q Z S } @

7 H R & ~

8 I S _ `

9 J T '

After the file name is the way you want, press the (ENTER) button.
This will display a confirmation message (SURE?). If you want to cancel the renaming operation, press the (NO) or (EXIT) button.
The message Please Wait will remain on the display while the rename operation is being performed. Do not perform any Digital Piano operation while this message is on the display. Complete appears on the display after renaming is complete.

Playing Back a Song from a Memory Card
You can use the procedure below to play back a user song (page E-24) stored on a memory card without loading the song into Digital Piano memory.
Playing Back All of the Songs in a Folder
Use the procedure below to select one of the four folders on a memory card and play back all of the songs in the folder in succession.

Memory Card Folders

Formatting a memory card on the Digital Piano will automatically create the four folders shown below. You put playback song data into any one of the folders. You can use the four folders to group your music data by family member, genre, or some other categories. Use buttons through (folders) to select a folder.
Folder Name MUSICDAT MUSIC__B MUSIC__C MUSIC__D Button Assignment
This will start tone demo tune playback (page E-23).
Press the (CARD/INTERNAL) button.
This will switch from tone demo tune playback to card tune playback. While playback is in progress, you can use the through buttons (folders) to switch playback to another folder. To stop playback, press the (PLAY/STOP) button.

(A) (B) (C) (D)

Assigning a Different Folder to a Folder Selection Button
You can use the following procedure to assign different folders to folder selection buttons , , and.

1. 2. 3. 4.

Store the music data you want to play back in one of the memory card folders. Insert the memory card into the Digital Pianos memory card slot. Press the (CARD/INTERNAL) button. Press one of the folder selection buttons ( through ) to select the card folder you want. This will display the song number and song name of the first song in the folder you selected. Use the (w, q) buttons to select the song you want. Press the (PLAY/STOP) button.
This will start playback. Each press of (PLAY/STOP) starts and stops playback. Fast forward, fast reverse, tempo changes, and other operations are the same as those during playback of a user song in Digital Piano memory. For details, see Playing Back a Specific Music Library Song (page E-24).
While holding down the (FUNCTION) button, press the folder selection button (, , or ) whose folder assignment you want to change.
This displays the folder assignment screen for the button you press.
Use the (w, q) buttons to select the folder you want to assign to the button.
You can select any folder on the memory card.
After selecting a folder, you can rename it if you want.

Perform steps 6 through 8 of the procedure under Renaming a Memory Card File (page E-47) to rename the folder.
To quit memory card data playback, press the (CARD/INTERNAL) button.
Even when you do not have a memory card loaded in the Digital Pianos memory card slot, you can save up to about 16MB of data in the Digital Pianos internal memory area. You also can load and delete internal memory area data using the same procedures that you use with a memory card.
Remove the memory card from the Digital Pianos memory card slot (page E-44).
Removing the memory card from the slot enables internal memory area data operations (save, load, delete, rename, playback).
To do this Save data to the internal memory area Load data from the internal memory area Delete data from the internal memory area Rename a file in the internal memory area Play back a song in the internal memory area
Perform this operation From step 2 under Saving Digital Piano Data to a Memory Card on page E-45 From step 2 under Loading Data from a Memory Card on page E-46 From step 2 under Deleting Memory Card Data on page E-47 From step 2 under Renaming a Memory Card File on page E-47 From step 3 under Playing Back a Song from a Memory Card on page E-48 The operation in step 4 of the above procedure is not possible in the case of internal memory area song playback.
Saving Data to Digital Piano Memory (Internal Area) Instead of a Memory Card

Error Messages

One of the error messages below appears on the display when a problem occurs. All mentions of memory card in the following table refer to an SD memory card.
Display Message Convert Cause Required Action
Reduce the size of the recorder song data by deleting unneeded There is not enough Digital Piano memory available to convert a recorder song (page E-34) to SMF data and store tracks (page E-37), if there are any. it on the memory card. You are trying to use the procedure under Renaming a Memory Card File (page E-47) to change to a file name that already exists on the memory card. 1. The current memory card format is not compatible with this Digital Piano. 2. The memory card capacity is greater than 2GB. 3. There is something wrong with the memory card. Use a different file name.

FileName

Format
1. Format the memory card on the Digital Piano (page E-45). 2. Use a memory card with a capacity of 2GB or less. 3. Use a different memory card. 1. Delete some of the files on the memory card to make room for new data (page E-47), or use a different card. 2. Delete some or all user data from Digital Piano memory to make room for new data. 1. Use a different memory card. 2. Back-up Digital Piano memory data by copying it to your computer, and then turn the Digital Piano off and then back on again. Note that you may not be able to back-up Digital Piano data in certain cases.

Use the (w, q) buttons to select the song you want to play. Press the (PLAY/STOP) button.
This starts playback of the selected song. Each press of the (PLAY/STOP) button toggles between play and stop. Fast forward, fast reverse, tempo change, and other operations are the same as those during playback of a loaded user song and a song file on a memory card.
When you are finished playing back songs, press the (CARD/INTERNAL) button.

Assembling the Stand

Unpacking

PREPARATION

*CAUTION
Assembly of the stand should be performed by at least two people working together. This stand should be assembled on a flat surface. Do not remove the tape securing the keyboard cover in place until assembly is complete. Removing the tape can cause the keyboard cover to open and close during assembly, creating the risk of personal injury to your hands and fingers. Take care that you do not pinch your fingers between parts when assembling them.
This stand does not include any of the tools required for assembly. It is up to you to prepare a large Philips head (+) screwdriver for assembly.

To assemble the stand

Part Qty 2 Pedal cable 4 2
Unfasten the band that bundles the pedal cable to the back of the crosspiece and pull the pedal cord out from the crosspiece.
Attach the side panels and to the crosspiece. Secure the side panels using the four screws. When installing part , slide the brackets into the slots in either end crosspiece. If the brackets are not inserted into the ends of the crosspiece as far as they will go, the screws will not be able to enter into the screw holes of the brackets , which can
strip the threads of the screws. Cover the screw heads with the caps.
If anything is missing or damaged, contact your local CASIO service provider. Do not use any screws other than those that come with the stand. Doing so risks damage to the stand and/or the Digital Piano.

J A E D E 3 B J

Slide the back panel into the grooves of the side panels.
Attach the right side of the back panel to the bracket of the side panel. Secure the back panel in place with a screw.
Be sure to check that the back panel bracket engages correctly with the side panel bracket as shown in the nearby illustration marked O. Assembling the stand while these brackets are not engaged correctly (as shown in the illustration marked X) creates the risk of damage to stand components.

Back panel bracket

Pull the side panel slightly outwards in the direction marked with in the illustration below.
Check to make sure that the relative positions of the back panel bracket and the side panel bracket are as shown in the illustration A. This step creates a slight gap between the side panels and , which makes it easier to mount the Digital Piano onto the stand in step 6 below.

Side panel bracket

Place the piano onto the stand.
In order to ensure you do not get your fingers pinched between the piano and the stand, grasp the piano on its sides (not its ends) at the locations marked with stars () in the illustration.
First, use the two butterfly bolts to secure the back of the piano to the stand. Next, use the two screws to secure the front of the piano.
At least 10cm At least 10cm
The butterfly bolts and the screws keep the piano from slipping off the stand. Never use the piano without the butterfly bolts and the screws installed.
At this time the screws on the bottom of the piano should hook into the cutouts in the stand brackets.

Back of piano

Attach the left side of the back panel to the bracket of the side panel. When attaching the back panel, place the clip on the screw as shown in the illustration below.
Stand side panel Bracket cutout
Next, secure the bottom of the back panel with the six screws.

To connect cables

Pedal plug
10. Adjust the height adjustment screw to
provide support so the crosspiece does not bow downwards when the pedals are pressed.
Check to make sure that the POWER button is in the OFF position (raised). If power is on, press the POWER button to turn it off. Plug the power cord that comes with the Digital Piano into the AC power jack on the bottom of the Digital Piano.*
Pressing the pedals without adjusting the height adjustment screw can result in damage to the crosspiece. Always make sure you adjust the height adjustment screw before operating the pedals.

Power Cord

The shape of the power cord plug and household power outlet receptacle differ according to country and geographical area. The illustration shows just one example of the shapes that are available. With the AP-620BK and AP-6BP, the power cord is hard-wired to the Digital Piano.
Orienting the pedal plug as shown in the illustration, plug it into the pedal connector on the bottom of the piano. Secure the pedal cord with the clip.
To install the music stand and headphones hook
Insert music stand into the groove on the Digital Piano console as shown in the figure below.

Household power outlet

The screws of the stand can work loose due to the effects of temperature and humidity changes, vibration, etc. Because of this, you need to periodically check the screws for proper tightness. Retighten any loose screws you find. To power the Digital Piano, use a power outlet that allows easy access when plugging in or unplugging the power cord.

Pedals Other Functions

Damper (with half-pedal operation), Soft, Sostenuto

MIDI SD Memory Card

16 multi-timbre received, GM Level 1 standard SD memory card slot Supported SD Memory Cards: Up to 2GB Functions: SMF playback, file storage, file recall, card format PHONES jacks: Stereo standard jacks 2 MIDI OUT/IN terminals LINE OUT R, L/MONO jacks: Standard jacks 2 Output impedance: 2.8K Output voltage: 1.8V (RMS) MAX LINE IN R, L/MONO jacks: Standard jacks 2 Input impedance: 9.0K Input voltage: 200mV USB port: Type B Pedal connector

Inputs/Outputs

Speakers Power Requirements Power Consumption Dimensions Weight
16cm 2 + 5cm 2 (Output 30W + 30W)
AP-620BK/AP-6BP : 120V AP-620BKV/AP-6BPV : 220-240V 78W Digital Piano and Stand: 141.2 (W) 49.2 (D) 90.0 (H) cm (55 5/3/7/16 inch) Digital Piano and Stand: AP-620BK/AP-620BKV: Approximately 57.1 kg (125.9 lbs) AP-6BP/AP-6BPV: Approximately 58.2 kg (128.3 lbs)
* Based on 1KB = 1024bytes, 1MB = 10242 bytes Specifications and designs are subject to change without notice.

Operating Precautions

E-63 Be sure to read and observe the following operating precautions.

Location

Avoid the following locations for this product. Areas exposed to direct sunlight and high humidity Areas subjected to temperature extremes Near a radio, TV, video deck, or tuner The above devices will not cause malfunction of the product, but the product can cause interference in the audio or video of a nearby device.

User Maintenance

Never use benzine, alcohol, thinner, or other chemical agents to clean the product. To clean the product or its keyboard, wipe with a soft cloth moistened in a weak solution of water and a mild neutral detergent. Wring all excess moisture from the cloth before wiping.
Included and Optional Accessories
Use only accessories that are specified for use with this product. Use of unauthorized accessories creates the risk of fire, electric shock, and personal injury.

Weld Lines

Lines may be visible on the exterior of the product. These are weld lines that result from the plastic molding process. They are not cracks or scratches.

Drum Assignment List/Lista de sonidos de batera
STANDARD SET 4 ROOM SET HIP-HOP SET POWER SET SYNTH SET 1 SYNTH SET 2 TRANCE SET JAZZ SET BRUSH SET ELECTRONIC SET ORCHESTRA SET
Key/Note Number Nmero de clave/nota

STANDARD SET 1

STANDARD SET 2

STANDARD SET 3

E b 1 27

F # 1 30

Closed Hi-Hat Pedal Hi-Hat Open Hi-Hat Ride Cymbal 1

A b 1 32

Standard4 Kick 2 Standard4 Kick 1 Room Kick 2 Room Kick 1 Room Snare 1 Room Snare 2 Room Low Tom 2 Hip-Hop Closed Hi-Hat Room Low Tom 1 Hip-Hop Pedal Hi-Hat Room Mid Tom 2 Hip-Hop Open Hi-Hat Room Mid Tom 1 Room High Tom 2 Room High Tom 1 Reverse Cymbal Synth1 Tambourine Synth1 Cowbell Synth1 Cowbell Trance Tambourine Room High Tom 1 Elec. High Tom 1 Synth2 High Tom 1 Room Mid Tom 1 Room High Tom 2 Elec. Mid Tom 1 Elec. High Tom 2 Room Mid Tom 2 Elec. Mid Tom 2 Room Low Tom 1 Elec. Low Tom 1 Power Snare 2 Room Low Tom 2 Elec. Snare 2 Elec. Low Tom 2 Power Snare 1 Elec. Snare 1 Jazz Snare 1 Elec. Kick 2 Elec. Kick 1 Standard4 Snare 1 Standard4 Snare 2 Synth2 Kick 2 Synth2 Kick 1 Synth1 Rim Shot Synth2 Snare 1 Power Kick 2 Power Kick 1 Jazz Kick 2 Jazz Kick 1

B b 1 34

C # 2 37
Standard2 Kick 2 Standard2 Kick 1

Jazz Kick 1 Concert BD

E b 2 39
Hip-Hop Kick 2 Hip-Hop Kick 1 Hip-Hop Side Stick Hip-Hop Snare 1 Hip-Hop Hand Clap Hip-Hop Snare 2
Trance Kick 2 Trance Kick 1 Trance Side Stick Trance Snare 1 Trance Hand Clap Trance Snare 2
Jazz Kick 2 Brush Kick Brush Side Stick Brush Snare 1 Brush Slap Brush Snare 2

F # 2 42

A b 2 44

B b 2 46

C # 3 49
Standard3 Kick 2 Standard3 Kick 1 Standard3 Side Stick Standard2 Snare 1 Standard3 Snare 1 Standard3 Hand Clap Standard2 Snare 2 Standard3 Snare 2 Standard3 Low Tom 2 Standard2 Closed Hi-Hat Standard3 Closed Hi-Hat Standard3 Low Tom 1 Standard2 Pedal Hi-Hat Standard3 Pedal Hi-Hat Standard3 Mid Tom 2 Standard2 Open Hi-Hat Standard3 Open Hi-Hat Standard3 Mid Tom 1 Standard3 High Tom 2 Jazz Snare 2 Synth2 Snare 2 Synth2 Low Tom 2 Synth2 Closed Hi-Hat 1 Trance Closed Hi-Hat Synth2 Low Tom 1 Synth2 Closed Hi-Hat 2 Trance Open Hi-Hat 1 Synth2 Mid Tom 2 Synth2 Open Hi-Hat Trance Open Hi-Hat 2 Synth2 Mid Tom 1 Synth2 High Tom 2 Synth1 Kick 2 Synth1 Kick 1 Synth1 Rim Shot Synth1 Snare 1 Synth1 Hand Clap Synth1 Snare 2 Synth1 Low Tom 2 Synth1 Closed Hi-Hat 1 Synth1 Low Tom 1 Synth1 Closed Hi-Hat 2 Synth1 Mid Tom 2 Synth1 Open Hi-Hat Synth1 Mid Tom 1 Synth1 High Tom 2 Synth1 Crash Cymbal Synth1 High Tom 1 Synth1 Ride Cymbal

E b 3 51

Standard3 High Tom 1

F # 3 54

A b 3 56

Concert SD Castanets Concert SD Timpani F # Timpani F Timpani G # Timpani G Timpani A # Timpani A Timpani B Timpani c # Brush Crash Cymbal 1 Timpani c Timpani d # Brush Ride Cymbal 1 Timpani d Timpani e Brush Ride Bell Timpani f Brush Tambourine Brush Splash Cymbal Brush Crash Cymbal 2 Concert Cymbal 2 Brush Ride Cymbal 2 Concert Cymbal 1

B b 3 58

C # 4 61

E b 4 63

Synth1 High Bongo Synth1 Low Bongo Synth1 Mute Hi Conga Synth1 Open Hi Conga Synth1 Open Low Conga

F # 4 66

A b 4 68

B b 4 70

Synth1 Maracas

C # 5 73

E b 5 75

Synth1 Claves

F # 5 78

A b 5 80

B b 5 82

C # 6 85

E b 6 87
High Q Slap Scratch Push Scratch Pull Sticks Square Click Metronome Click Metronome Bell Standard1 Kick 2 Standard1 Kick 1 Side Stick Standard1 Snare 1 Hand Clap Standard1 Snare 2 Low Tom 2 Closed Hi-Hat Low Tom 1 Pedal Hi-Hat Mid Tom 2 Open Hi-Hat Mid Tom 1 High Tom 2 Crash Cymbal 1 High Tom 1 Ride Cymbal 1 Chinese Cymbal Ride Bell Tambourine Splash Cymbal Cowbell Crash Cymbal 2 Vibraslap Ride Cymbal 2 High Bongo Low Bongo Mute High Conga Open High Conga Open Low Conga High Timbale Low Timbale High Agogo Low Agogo Cabasa Maracas Short High Whistle Long Low Whistle Short Guiro Long Guiro Claves High Wood Block Low Wood Block Mute Cuica Open Cuica Mute Triangle Open Triangle Shaker Jingle Bell Bell Tree Castanets Mute Surdo Open Surdo Applause 1

Applause 2

indicates a key is assigned the same tones as it is for STANDARD SET 1.
indica una clave asignada a los mismos tonos que para STANDARD SET 1.
Rhythm List/Lista de ritmos
Group Name/ Nombre del grupo POPS/JAZZ POPS 8 BEAT/16 BEAT 021 DANCE ROCK JAZZ EUROPEAN 058 POP 1 POP 2 FAST POP FUNK POP POP ROCK 6/8 POP FAST SOUL SLOW SOUL 60S SOUL POP SHUFFLE STRAIGHT 8 BEAT 1 STRAIGHT 8 BEAT 2 FUNK 8 BEAT MELLOW 8 BEAT GUITAR 8 BEAT 8 BEAT 8 BEAT POP OLDIES 8 BEAT 60S 8 BEAT 16 BEAT 16 BEAT SHUFFLE HIP-HOP DANCE POP DISCO POP TECHNO POP TRANCE MODERN R&B MODERN DANCE DISCO SOUL STRAIGHT ROCK SHUFFLE ROCK BLUES 1 BLUES 2 EP BLUES SLOW BLUES SOFT ROCK LATIN ROCK SLOW ROCK 50S ROCK 50S PIANO ROCK NEW ORLNS R&R 60S ROCK ROCK 70S PIANO ROCK ROCK WALTZ SLOW BIG BAND MIDDLE BIG BAND FAST BIG BAND SWING 1 SWING 2 SLOW SWING JAZZ WALTZ FOX TROT QUICKSTEP JAZZ COMBO 1 SCHLAGER POLKA WALTZ 1 Group Number/ Nmero de grupo Sequential Number/ Nmero secuencial Rhythm name/ Nombre del ritmo Group Number/ Nmero de grupo LATIN/WORLD LATIN I 015 LATIN II 026 COUNTRY Group Name/ Nombre del grupo 031 Sequential Number/ Nmero secuencial Rhythm name/ Nombre del ritmo WALTZ 2 SLOW WALTZ VIENNESE WALTZ FRENCH WALTZ SERENADE TANGO MARCH 1 MARCH 2