KL-750

Owners Manual

Introduction

Congratulations on your selection of the CASIO KL-750 Label Printer. This CASIO Label Printer makes it possible for you to print adhesive labels for a wide variety of applications, such as: name tags, cassette tape labels, floppy disks, binders, and other applications. You can produce attractive, original labels thanks to such features as: Variable tape sizes (6mm, 9mm, 12mm, 18mm) Attractive sans-serif font Font effects (shading, underline, box) Built-in symbols Text memory

Contents

Part 1 Getting Acquainted.. 2
Important Precautions... 2 General Guide.... 3 Label Printer Menus... 4

English

Part 2 Getting Ready... 4
Power Supply... 4 Replacing Batteries.... 4 To replace the batteries... 5 AC Adaptor.... 5 To connect the AC adaptor... 5 Turning Power On and Off... 5 Resetting the Memory... 5 To reset the memory... 5 Auto Power Off Function... 5 Tape Cartridges.... 5 To load a tape cartridge... 6 Tape Width Specification... 6 To specify 6mm tape width... 6
You can even use tapes with optionally available holders to create your own stamps. All of this makes the CASIO label Printer the perfect tool for just about all of your labeling needs!
Part 3 Inputting Characters and Symbols.. 7
Display Symbols and Indicators... 7 Basic Alpha-Numeric Input... 8 To input alpha-numeric characters... 8 About the CODE key... 8 Special Symbols... 8 To input special symbols... 8 Important! Contact a nearby dealer whenever you require servicing. Note that the manufacturer shall not be held liable for any loss or claims by third parties which may arise out of the use of this product. Note that the manufacturer shall not be held liable for any damages incurred as a result of data loss caused by malfunctions, repairs, or interruption of power supply. It is up to the user to keep backup records of important data. Keep this manual on hand for future reference.
Part 4 Deleting and Inserting Characters. 9
Moving the Cursor... 9 To move the cursor... 9 Deleting Individual Characters.. 9 To delete characters using the BS key... 9 To delete characters using the DEL key.. 9 Clearing the Display... 9 To clear the display... 9 Text Editing.... 9 To insert new characters... 9 To change existing characters to different ones. 10 E-1
Part 5 Character Size and Text Effects.. 10
Character Size.... 10 To change the character size... 10 Text Effects.... 11 To specify a text effect... 11

Part 1

Getting Acquainted

Part 6 Printing... 11

Printing a Tape.... 11 To print a tape.... 11 Stamp Printing.... 12 To print a stamp tape... 12 Mirror Image Printing... 12 To turn mirror image printing on and off.. 12 Other Printing Features and Operations.. 12 Auto Feed.... 13 To turn auto feed on and off... 13 To manually feed tape... 13 Print Density... 13 To adjust the print density... 13
This part of the manual provides you with important information you need to know in order to use the Label Printer to its full potential. Be sure to read it carefully before using the Label Printer for the first time.

Important Precautions

Keep your Label Printer out of areas subject to temperature extremes, moisture and direct sunlight. The recommended temperature range is 10 to 35C (50 to 95F). Dont let coffee, juice or other liquids splash onto the Label Printer. Never let paper clips, pins or other foreign objects get into the tape outlet slot or printer of the Label Printer. Do not pile heavy objects on top of the Label Printer. Never try to take the Label Printer apart or attempt your own maintenance. Do not drop your Label Printer and avoid strong impact. Do not pull on the tape or try to force it back into the Label Printer. The yellow cutter cartridge inside the Label Printer contains a sharp blade for cutting the printed tape. Keep your fingers away from this cartridge and be especially careful to keep the cartridge away from small children. Do not operate the cutter lever without a tape cartridge loaded in the Label Printer. Doing so can damage the cutter blade. Do not apply excessive force to the tape cutter lever. Doing so can damage the Label Printer. Do not use benzine, thinner, or other volatile chemicals to clean the exterior of the Label Printer. Use a soft, dry cloth or a cloth dampened in a weak solution of a mild, neutral detergent and water. Wring the cloth out until all excess moisture is removed. A dirty printer head can cause printing to become smudged. When this happens, clean off the printer head by wiping it with a cotton swab moistened with alcohol (page 15). Use of the Label Printer next to a television or radio may interfere with reception.

Part 7 Memory.... 13

To store data.... 13 To recall text from memory.. 13 To delete text from memory... 14

Part 8 Reference... 14

Replacing the Tape Cutter Blade... 14 To replace the tape cutter blade... 14 Cleaning the Printer Head and Roller... 15 To clean the printer head and roller.. 15 Initial Power On Settings... 15 Initializing the Label Printer... 15 To initialize the Label Printer... 16 Troubleshooting.... 16 Specifications... 17

General Guide

Front Power Keys Turn power on and off. Liquid crystal display (LCD) Tape cutter lever Tape cutter lever Function key Back/Left Side
Optional AC Adaptor connector Letter keys Battery compartment Tape Cutter Operation Precaution Note the following important precautions when operating the tape cutter lever. 1. When operating the tape cutter lever, make sure you do not press it too hard. 2. Always return the tape cutter lever by hand back to its original position after the tape is cut.

Tape outlet

Label Printer Menus
Label Printer operation is designed to be as simple as possible, thanks to onscreen menus that you can use to select the settings you need. Each menu is described in detail in the sections that follow in this manual, but note the following general points when using them. The item that is underlined in a menu is the one that is currently selected.

Replacing Batteries

A handy low battery power indicator lets you know when battery power is getting too low for proper operation. The message BATT appears on the display if battery power is low when you perform any of the following operations. Turn power on Execute a print operation Whenever the BATT message appears, press SET to clear it from the display. You should still be able to perform some Label Printer operations, but some power intensive operations (like printing) may become impossible if battery power is too low. In any case, you should replace batteries as soon as possible or switch to the AC adaptor as soon as possible after the BATT message appears. Important! Batteries can burst or leak and damage your unit if you do not use them correctly. Note the following important points. Be sure that the plus (+) and minus () sides of each battery are facing correctly. Never mix batteries of different types Never leave dead batteries in the Label Printer. Remove the batteries if you do not plan to use the Label Printer for a long time. Replace the batteries at least once every 2 years. Warning! Never use recharged batteries with the unit. Do not expose batteries to direct heat, do not short circuit them, and do not try to take them apart. Keep batteries out of the reach of small children. If swallowed, consult with a physician immediately. Be sure to replace the batteries in accordance with the battery life printed on the side of the battery itself.

Currently selected item

Use K and L to move the underlining up and down and change the selected item. Press SET to execute the underlined item, or ESC to exit the displayed menu (and return to the previous menu or screen) without selecting anything. When you press SET to execute a menu item, the Label Printer either moves on to the next menu, or it executes the selected function and returns to the text input screen that you started from.

Part 2

Getting Ready
This part of the manual tells you how to load batteries and the tape cartridge, and how to perform other basic setups for the Label Printer. Important! Be sure to read this section before attempting to use the Label Printer.

Power Supply

The Label Printer can be powered by eight AA-size batteries or an optional AC adaptor (AD-A95100).

To replace the batteries

1. Turn power off. If you are using the optional AC adaptor for power, you should also unplug it from the Label Printer. 2. Open the battery compartment cover on the back of the Label Printer by sliding it in the direction indicated by the arrow. 3. Remove all eight of the old batteries.

Turning Power On and Off

Press ON to turn power on, and OFF to turn power off. Important! If you are using the Label Printer for the first time, you should reset it first.

Resetting the Memory

You should reset the memory of the Label Printer before using it for the first time, after you have not used it for a long time, or if nothing happens when you turn power on, even after you change the batteries. Important! Resetting Label Printer memory clears its memory of all input data.
4. Load a set of eight new batteries into the battery compartment, making sure that their positive (+) and negative () ends are facing in the correct directions. 5. Replace the battery compartment cover.

To reset the memory

1. Make sure that Label Printer power is off. 2. While holding down the PRINT and ESC keys, press ON to turn power on. 3. Keeping PRINT and ESC held down, release the ON key only.

AC Adaptor

Note the following important precautions when using an AC adaptor to power your Label Printer. Use only a genuine CASIO AD-A95100 AC adaptor with the same voltage rating as the household current in your area. Using a wrong adaptor can damage your Label Printer. Be sure to turn the Label Printer off before you connect the adaptor. Do not turn power on until the adaptor is connected to the Label Printer and plugged into and AC outlet. Be sure to unplug the AC adaptor from the AC outlet whenever you are not using the Label Printer.

4. Press SET to initialize the Label Printer or ESC to abort the reset operation without initializing anything. See Initializing the Label Printer on page 15 for information on the initial default settings of the Label Printer following the reset operation.

Auto Power Off Function

If you do not perform any key operation for about six minutes, the Label Printer automatically turns power off. To restore power, press ON.
To connect the AC adaptor
Connect the adaptor to the Label Printer as illustrated nearby. Plug the other end into a standard household AC outlet.

Tape Cartridges

Use the procedures described below to load a tape cartridge into the Label Printer. After you load the tape cartridge, be sure to use the procedure described under Tape Width Specifications on page 6 to tell the Label Printer what is the width of the tape you are using.
Important! Never try to push the tape back into the cassette. Once tape is out of the cassette, there is no way to wind it back in. Trying to do so can cause operational problems with the Label Printer.

To load a tape cartridge

1. Make sure that the Label Printer is turned off. 2. Open the tape cartridge compartment cover. If there is a cartridge already in the Label Printer, remove it by grasping the cartridge on both sides with your thumb and forefinger, and lift straight up.
4. Use a pencil or some other thin object to take up slack in the ink ribbon as shown in the illustration. Note that the tape does not move at this time. If the ink ribbon is slack when you load it into the Label Printer, it can break or cause some other problem. Be sure to turn the ink ribbon take up spool only in the direction indicated by the arrow (a). Turn the spool until the other spool (b) starts turning in the direction noted by the arrow. This indicates there is no slack in the ribbon. 5. Load the tape cartridge into the Label Printer, making sure that the tape and ink ribbon pass between the head and roller. 6. Close the tape cartridge compartment cover.
3. Remove the stopper from a new tape cartridge and check to see that the tape is ready to use.

Roller Head

Make sure that the tape is under the tape guide and that it is not bent or twisted.

Tape guide

7. Turn on Label Printer power and press FUNCTION and then PRINT (FEED) two or three times to make sure that the tape comes out without any problem. If the tape does not come out normally, turn off power and start again from step 1 above.

Tape Width Specification

Important! When using 6mm tape, using certain character sizes can cause characters to run off the top or bottom of the tape. Be sure to use the following procedure to tell the Label Printer when you are using 6mm tape.
To specify 6mm tape width
Make sure that the tape does not extend too far past the tape guide. If it does, cut off the end with a pair of scissors. 1. Turn power on. 2. Press FUNCTION and then 9 (6mm). 3. Press H J K or L to change the setting shown on the display between ON (6mm tape) and OFF (other tape width). 4. When the tape width setting is the way you want it, press SET to register it. The tape width you set remains in effect until you change it or reset the Label Printers memory. E-6

Part 3

Inputting Characters and Symbols
This part of the manual tells you how to input characters. To make things easier to understand, we call everything you input a character, regardless of whether it is actually a letter, number, or symbol. Explanations here all use the default settings that are in effect from the initial power-on screen. For information on using other character styles, effects and sizes, see page 10. Important! You can input up to 63 characters per label. Further input becomes impossible after you input the 63rd character.
Shift indicator This indicator appears when you press the SHIFT key. While this indicator is on the display, the keyboard is shifted, so the letter keys input upper-case alpha characters. The number keys input the punctuation symbols marked in the upper right corners of the keys. If both the caps mode indicator and the shift indicator are shown on the display, the keyboard is shifted to lower-case input. The keyboard automatically unshifts (and the shift indicator disappears) as soon as you input a character. Code indicator This indicator appears when you press the CODE key. While this indicator is on the display, number keys 1 through 5 input the accents marked above them and the O, S and C keys input the special characters marked in their lower right corners. The keyboard automatically returns to normal (and the code indicator disappears) as soon as you input an accent. Caps indicator This indicator appears when the Label Printer is in the caps (upper-case) mode. All letters you input in the caps mode are upper-case. When the caps mode indicator is not shown on the display, all letters are input as lower-case. Note that the Label Printer stays in the caps mode until you press the CAPS key again. If both the caps mode indicator and the shift indicator are shown on the display, the keyboard is shifted to lower-case input. Effect indicators These indicators point to the character effect that is currently in use. You can select between shading, underline, and box. Stamp printing indicator This indicator appears when the Label Printer is set up for stamp printing. Labels you create with stamp printing can be attached to an optionally available stamp holder and then used as a pre-inked stamp. Mirror image printing indicator This indicator appears when the Label Printer is set up for mirror image printing. Normal (non mirror image) printing is performed when this indicator is not shown.

Display Symbols and Indicators
Before getting into actual input, you should first become acquainted with the symbols and indicators used on the Label Printer display.

Function indicator

Effect indicators

Stamp printing indicator

Shift indicator Code indicator

FUNCTION SHIFT CODE CAPS

Character position marks

STAMP MIRROR M-FEED 6mm

Mirror printing indicator Manual feed indicator

Caps indicator

Cursor 6mm tape indicator
Function indicator This indicator appears when you press the FUNCTION key. Pressing a key while this indicator is on the display causes the function marked above that key to be executed.
Manual feed indicator This indicator appears when you are using manual feed instead of auto feed. Auto feed is in effect when this indicator is not on the display. Important! After you finish printing when using manual feed, be sure to always press FUNCTION and then PRINT (FEED) to feed the tape before cutting it. If you dont you will cut off part of the printed text. 6mm tape indicator This indicator appears when you use the procedure on page 6 to specify you are using 6mm tape. No indicator is shown when you are using other (9mm, 12mm, 18mm) tape. Cursor The cursor shows the next input position. Any character you input appears at the point where the cursor is located. Character position marks These marks show where characters will appear as you input them. This part of the display is always blank when you turn power on.
If you input a wrong character, press BS to delete it and input again. See page 9 for other details on editing text. 3. When you reach the end of a line of text, press B (the L cursor key) to input a newline mark. A newline operation is indicated on the display by the symbol. This shows where you changed lines. 4. Input the characters in the second line. 5. To print the text that you input, press PRINT. For details on printing, see page 11.

About the CODE key

The CODE key makes it possible to input punctuation needed for a number of different languages. The following shows the key operations you should use for each of the characters formed using the CODE key.
Key Operation CODE CODE CODE CODE S* O C 1 Input Key Operation CODE CODE CODE CODE Input
Basic Alpha-Numeric Input
The following operation shows you the basic procedures for inputting letters and numbers. We will explain the procedure by inputting the following characters using the default initial power-on screen. ABXYZ Computer Company 1234567890 Note If you hold down any key, it will repeat its operation or input at high speed until you release it.

* Lower case only. Example: To input. CODE 1 A

Special Symbols

You can also access a menu of special symbols by pressing FUNCTION 4 (SYMBOL).

To input special symbols

Example: To input the special symbol #. 1. With the cursor at the location where you want to input a special symbol, press FUNCTION 4 (SYMBOL). The symbol that is underlined on the display is the one that is currently selected.
To input alpha-numeric characters
1. Turn power on. 2. Input the first line of characters. To input the upper-case letters, you can use either SHIFT or CAPS. With SHIFT you must shift the keyboard for each character. With CAPS the keyboard stays in upper-case until you press CAPS again. Press SPACE to input spaces.
2. Use the H and J cursor keys to move the underlining to the symbol you want. Not all of the available symbols fit on the display. The menu will scroll when you press the cursor keys. In this example, underline #. 3. After you underline the symbol you want, press SET. This returns to the input screen, with the symbol you selected input at the location where the cursor was located when you displayed the symbol list.
To delete characters using the BS key
Example: To change the word commmputer to computer. 1. Use H and J to move the cursor under p.
2. Press BS twice to delete the two ms to the left of the cursor, shifting puter to the left as you do. 3. Press FUNCTION and then J to jump back to the end of the characters for more input.
To delete characters using the DEL key

Part 4

Deleting and Inserting Characters
Example: To change the word commmputer to computer. 1. Use H and J to move the cursor under the first (far left) m. 2. Press DEL twice to delete the two ms at the cursors position, shifting mputer to the left as you do. 3. Press FUNCTION and then J to jump back to the end of the characters for more input.
This section describes everything you need to know about deleting and editing characters you have already input.

Moving the Cursor

Use the cursor keys to move the cursor around the display and position it for deleting and editing characters.

Clearing the Display

Use the following procedure to clear all input text from the display.

To move the cursor

Press H to move the cursor to the left, and J to move the cursor to the right. Press FUNCTION and then H to make the cursor jump to the beginning (far left) of the characters on the display. Press FUNCTION and then J to make the cursor jump to the end (far right) of the characters on the display. Holding down the H or J cursor key moves the cursor at high speed.

To clear the display

Press FUNCTION and then BS (CLS). At this time the message CLS? appears on the display to confirm that you want to clear the display. Press SET to clear or ESC to abort the operation without clearing anything.

Note You could also perform the above procedure in reverse, specifying the character size first and then inputting the text.

Text Effects

There are three text effects that you can assign: shading, underlining, and boxed text. The following shows examples of each. Shading: Underlining: Boxed Text: Text effect changes are applied to printed text only. The appearance of the displayed text does not change, but the text effect indicators will show you when a text effect is being used. Important! Any text effect specification you make is applied to all the characters on the display. You cannot make multiple specifications for specific characters.

Part 6

Printing
This part of the manual includes all the information you need to print tapes. It also tells you how to print special stamp tapes that you can attach to an optional stamp holder to create your own original stamps. Printing Precautions Never turn power off while printing is being performed. Make sure that the tape outlet is not blocked before you start printing. Never operate the tape cutter while printer is being performed (indicated by the message PRNT on the display). During printing at very high density, printing of very long text, or repeat printing of the same text a number of times, the Label Printer may stop printing for about five seconds. This is not a malfunction, and normal printing should resume shortly (indicated by the message P R N T on the display).

To specify a text effect

Example: To shade the text ABXYZ. 1. Input the text. 2. Press FUNCTION 3 (EFFECT) to display a menu of text effects.
Normal (no effects) Shading Cursor

Printing a Tape

Printing a tape is as easy as pressing the PRINT key.

To print a tape

1. Press the PRINT key to print a tape of the text you have input and laid out. To stop a print operation that is in progress, press ESC.

Box Underline

3. Use H and J to move the cursor to the effect you want to use. 4. When the cursor is located under the effect you want to specify, press SET to select it and return to the text display.
Note You could also perform the above procedure in reverse, specifying the text effect first and then inputting the text.
2. After the print operation is complete, press down on the tape cutter lever to cut the tape. 3. Use scissors to trim the tape to the size you want, if necessary. After you print a tape, you can peel off its paper backing and stick the tape onto the object you Backing want. Note that the tape will not stick on coarse, wet, oily, or soiled surfaces. Also, you should not try to use the tape where it is exposed to direct Tape sunlight or rain. Do not stick the tape onto human skin. An easy way to remove the backing from a tape and expose the adhesive surface is to bend the tape near one of its ends. This should cause the tape and its backing to separate, allowing you to pull them apart. E-11

Auto Feed

You can turn the Label Printers auto feed feature on and off. When auto feed is on, the Label Printer automatically feeds the tape about 12mm at the beginning and end of each print operation. This creates identical margins on both sides of your text. Important! After you finish printing when using manual feed, be sure to always press FUNCTION and then PRINT (FEED) to feed the tape before cutting it. If you dont you will cut off part of the printed text.

Part 7

Memory
This part of the manual tells you how to store text data in memory for instant recall when you need it. You can store two blocks of text in memory, each containing up of 63 characters, for a total of 126 characters.

To store data

1. Input the text you want to store. 2. Press FUNCTION and then 1 (MEMO).
To turn auto feed on and off
1. Press FUNCTION and then 7 (M-FEED).
2. Press H J K or L to change the setting shown on the display between YES (manual feed) and NO (auto feed). 3. When the feed setting is the way you want it, press SET to register it.
3. Press SET to store the text in memory or ESC to abort the store procedure without storing anything. If there is nothing in memory yet, your text is automatically stored in Area 1. If Area 1 already contains data, your new input is automatically stored in Area 2. If there is not enough room for your text to fit in memory, the message FUL! appears when you press SET in step 3.

OK EFG

To manually feed tape
Press FUNCTION and then PRINT (FEED) to feed the tape 13mm.

Print Density

The print density setting controls how darkly figures are printed on your tapes.
To adjust the print density
1. Press FUNCTION and then 8 (DENSITY).
To recall text from memory
2. Use H and J to move the underlining to the density setting that you want. The lightest setting is 1, while the darkest setting is 5. The standard setting is 3. Only four of the five settings that are available can appear on the display. The display scrolls left and right when necessary to shows all of the available settings. 3. When the density setting is the way you want it, press SET to register it.

Example: To recall the contents of Area 2 while memory contains the following text. Area 1: ABCDEFG Area 2: CASIO 1. While the input screen is on the display, press FUNCTION and then 1 (MEMO). Note that text recalled from memory will replace any text currently on the display.
2. Press L to change to the text recall prompt.
3. Press SET. If all of the text does not fit on the display, you can use H and J to scroll it to the left and right.

Area 1 text

4. Use K and L to select Area 1 or Area 2 then press SET.
4. Press L to change to Area 2. Use K and L to switch between Area 1 and Area 2.
5. Press SET to delete the text from the area that is currently on the display.

Area 2 text

Part 8

Reference

5. Press SET to recall the text from the area that is currently on the display. Note that recalling data from memory replaces anything that is currently on the input display. Memory text cannot be appended.

CASI STR? DEL?

This section contains information about the Label Printer that you can use as reference when you need it.
Replacing the Tape Cutter Blade
To delete text from memory
1. While the input screen is on the display, press FUNCTION and then 1 (MEMO). The tape cutter blade is designed to provide approximately 3,000 cuts. Use the following procedure to replace the blade whenever it starts to cut poorly.
To replace the tape cutter blade
1. Make sure that the Label Printer is switched off. 2. Open the tape cartridge compartment cover.
2. Press L twice to change to the text delete prompt.
If there is a cartridge already in the Label Printer, remove it by grasping the cartridge on both sides with your thumb and forefinger, and lift straight up.
4. Use a cotton swab dipped in alcohol to clean the printer head and roller as shown in the illustration.

Printer head

3. Use a thin, pointed object to lift the yellow cutter cartridge out of the Label Printer as shown in the illustration.

Roller

The tape cutter blade comes out of the cutter cartridge if you press on the front of the cartridge. Be sure to take care to avoid cutting your fingers on the blade.
5. Replace the tape cartridge and close the compartment cover.
Initial Power On Settings
The following are the initial settings of the Label Printer whenever you turn it power on. Item SIZE EFFECT MIRROR M-FEED 6mm Power On 22 CANCEL OFF NO OFF
4. Install a new cutter cartridge by sliding it along the groove provided in the Label Printer. Contact your CASIO dealer to purchase a replacement cutter cartridge. 5. Replace the compartment cover.
Cleaning the Printer Head and Roller
A dirty printer head and roller can result in poor printing quality. If you have problems with print quality, use the following procedure to clean the printer head and roller.

Initializing the Label Printer
If you experience serious malfunction of the Label Printer or if operation fails completely, try performing the following operation to initialize the printer. Important! Initializing the Label Printer deletes all memory contents. Make sure you have a back-up copy of text stored in memory if you need it.
To clean the printer head and roller
1. Make sure the Label Printer is turned off. 2. Press the tape cartridge compartment cover release and open the compartment cover. 3. Remove the tape cartridge.
To initialize the Label Printer
1. Turn power off. 2. While holding down the PRINT and ESC keys, press ON to turn power on. 3. Keeping PRINT and ESC held down, release the ON key only. This prompt confirms whether or not you want to initialize the Label Printer.

Troubleshooting

Problem Possible Cause Attempt to input two marks within the same text. Attempt to input mark while 6mm is specified as the tape width. Label text containing a mark was input and then tape width specification was changed to 6mm. (ERR! message appears when you try to perform a print operation.) Text that is longer than 5.5cm when stamp printing is selected. Attempt to print a stamp while 6mm is specified for the tape width. Both text memory areas (AREA 1 and AREA 2) already contain text. Battery power is too low. Memory data has become corrupted for some reason. Action Use only one mark. Only two lines of text can be input, so text can contain only one mark. Do not use marks. 6mm tape can have only one line of text, so text cannot contain any marks. Delete the mark to print on 6mm tape or switch back to a wider tape.
ERR! message on the display.
4. Press SET to initialize the Label Printer or ESC to abort the reset operation. The following table shows the initial settings. Item Display Memory SYMBOL EFFECT M-FEED MIRROR MEMO DENSITY WIDTH Reset Cleared Cleared , CANCEL NO OFF STR? 3 OFF
Shorten the text to be printed and try again. Change the tape width setting to OFF and try printing the stamp again. Delete text from one of the text memory areas and then store the new text. Replace batteries. Initialize the Label Printer. E-16
FUL! message on the display.
BATT message on the display. ERR! message on the display.

Specifications

Model: KL-750 Input Keyboard Layout: Typewriter (QWERTY) Character Types Alpha (English and other languages): 99 Numbers: 10 Symbols: 37 Display Type: Liquid crystal display Columns: 4 Character matrix: 57-dot Printing Type: Thermal transfer Speed: Approximately 6.67mm/second Width: 4mm (6mm tape) or 8mm (other tape) Character Matrix: 2424-dot Character font: Sans-serif Character effects: Shade, underline, box Character sizes: 11, 12, 13, 21, 22, 23 Number of lines: 1 (6mm tape); 1 or 2 (other tapes) Memory Text: Up to approximately 126 characters (total storage for AREA 1 and AREA 2) General Power supply: Eight AA-size batteries or optional AD-A95100 AC adaptor Battery life: Approximately 1 tape cartridge (continuous printing) Power consumption: 9W Auto Power Off: Approximately six minutes after last key operation. Dimensions: 44.6 (H) 174 (W) 212 (D)mm (1 1/4"H 6 7/8"W 8 3/8"D) Weight: 452g (1lbs) Ambient Temperature: 10C~35C (50F~95F)

CASIO COMPUTER CO., LTD.

6-2, Hon-machi 1-chome Shibuya-ku, Tokyo 151-8543, Japan