CAT EYE ASTRALE 8

CYCLOCOMPUTER CC-CD200N E: Owners Manual

Warning

Pay attention to the road or trail! Do not be distracted by the computer. Be sure to securely mount the magnet, the sensor, and the bracket on your bicycle. Periodically check to insure they are mounted securely and the screws have not come loose. Keep batteries out of reach of small children. Dispose of batteries according to local regulations. Avoid unnecessary prolonged exposure to the sun. Never attempt to disassemble the computer head.

ASTRALE8

Please keep this manual in a safe place for future reference.
Important Dont use thinner, benzene or alcohol to wipe the surface of the Note computer. They may damage the surface of computer.
U.S. Pat. Nos.4633216/4642606/5226340/5236759 Pat. and Design Pat. Pending Copyright 2002/2003 CAT EYE Co. Ltd. CCMCD2N-1

Mount The Bracket

Secure the cord by fastening it to the frame with zip ties at regular intervals. Put the rubber pad 8 on the bracket 1 and secure the bracket on the handle bar with the screw. Slide the computer into the bracket until you hear the click sound. When you need to remove the computer, press the lever on the handlebar bracket and slide the computer forward. Note Allow enough wire clearance in the area marked with to insure you can turn the handlebars all the way from side to side without pulling the wire.
Please read these instructions carefully before installing or using the CAT EYE ASTRALE 8. Installation of the Computer on Your Bike
The computer comes with the following parts:
1 Bracket 2 Cord 3 Speed Sensor (Long Cord) 4 Cadence Sensor (Short Cord) 9 Sensor Rubber Pad Wheel Magnet Cadence Magnet Bracket Rubber Pad Nylon Ties (10)

Basic Functions Test

Spin the rear wheel to see if Speed is reading properly. Push the mode button until Cadence (Cdc) is in the sub-display. Spin the crank arm backwards to test if Cadence is reading properly. When you receive a signal, tightly secure the sensor so it does not move. Note When the computer does not indicate the speed/cadence, check the position of the magnet and the sensor.

Rotate the rear wheel.

Rotate the crank arm
Mount the wheel magnet and speed sensor
Mount the wheel magnet 6 on a spoke of the rear wheel so the surface of the magnet faces the sensor. Mount the speed sensor 3 (long cord) on the left chainstay with nylon ties 9. Note The nylon ties can only be used once, please install with care.

Computer Set-up

(For first use or after replacing the battery)

Rear wheel spoke

Contact Point
You need to know your tire size or the roll out length of your tire in MM's.

Sensor Side

The smooth edge of the zip tie should be on the outside

Left chainstay

Refer to the chart below for approximate tire lengths.
Tire size SET Button START/STOP Button MODE Button AC Button

Important Note

Mount the magnets 6 and the sensors 3 in the appropriate positions so that the center of each magnet 6 aligns with the marked sensor line when the rear wheel and crank arm are rotated. The magnet should be no more than 5mm from the sensor.
x1.x 1.x 1.x 1.x 1.x 1.x 1.x 1.x 1-3/x 1-3/x 1-1/x x 3/4 Tubular 24 x 1-1/x 1-1/x 1.x 2.x 2.x 7/x 1(59) 26 x 1(65) 26 x 1.x 1-1/x 1-3/x 1-1/x 1.x 1.x 1.x 1.x 2.x 2.x 2.x 2.x 3.x x 1-1/x 1-1/x 1-3/x 35A 650 x 38A 650 x 38B 700 x 18C 700 x 19C 700 x 20C 700 x 23C 700 x 25C 700 x 28C 700 x 30C 700 x 32C 700C Tubular 700 x 35C 700 x 38C 700 x 40C

Center Marked Line

Adjust Within 5 mm

All Clear

Push the AC button on the backside. * Push the AC button when using this system for the first time and every time the battery is replaced.

AC Button

Measurement Selection
Select the measurement unit, kilometer or mile, by pushing the MODE button. Fix it by pushing the SET button.
Mount the cadence magnet and cadence sensor.
Mount the cadence magnet 7 on the left crank arm so that it faces the sensor. Secure the cadence sensor 4 (short cord) on the left chain stay with nylon ties 9.

Kilometer

Inward Side of The Crank Arm Left Chain Stay
When the crank is spinning, the center of the magnet 7 should pass in front of the sensor 4 marking line. The distance between the sensor and the magnet 7 should be within 5mm. After adjusting the magnet and sensor, secure tightly with nylon ties.

Left Chain Stay

Set The Tire Circumference
Set the tire circumference in mm. Note Refer to the chart shown on the right. Setting is fixed and completed by pushing the SET button.
Increase the number Max. 2999 mm

Marked Line

Decrease the number Min. 10 mm

START/STOP

Crank Arm

Center

Preparation Complete.
(the screen will show the time measurement in this state) * The auto mode is ON in this state.
Tire size is usually shown on the sidewall of tires.

Computer Operations

Selection of the data-display mode (bottom of the screen) Press the Mode button to navigate to each of the sub-displays listed on the right. Press and hold the mode button for two seconds in any mode to display the Clock Time. Start or Stop of Measurements Measurement Unit Icon The computer can be programmed to run in either MANUAL MODE or AUTO TIME MODE. In Manual Mode you must press the START / STOP button to turn on and off the Timer, which records Distance and Average Speeds. In Auto Time the computer turns the Timer on and off depending on a signal from the sensor. When you push the button, Elapsed Time, Average Speed and Trip Distance are recorded, and stopped with the second push of the button. Auto Time Mode (Automatic Measurement) is lit, the measurements are automatically When the icon done. This is called auto-mode in which the rotation of the wheel is detected to make the measurements start or stop automatiis lit, you cannot start or stop the meacally. (When the icon surements by pushing the START/STOP button) Manual Measurements on the screen, you can start or When you dont see the icon stop the measurements by pushing the START/STOP button. When you push the button, Elapsed Time, Average Speed and Trip Distance are started, and stopped with the second push of the button. START/STOP How to set ON or OFF the Auto-Mode Tm Push the SET button while Elapsed Time (Tm) Trip Distance SET is (Dst) or Average Speed (Av) is displayed, then the icon Dst lit (ON) or turned OFF. Av
While Elapsed Time, Trip Distance or Average Speed is displayed

Display for Measurements

0.0 (4.0) - 300.0 km/h [0.0 (3.0) - 185 mph] or

Power-Saving Screen

(When no signal is received for about 1 hr. the screen switches to the power-saving mode)

Cadence

0.0 (20.0) - 299.9 rpm

Auto-mode Icon

When lit, the measurements starts or stops automatically.
When you push either of the MODE button or the START/STOP button or you ride the bicycle, the display comes back to the measurement display.
Mode Selection Illustrations (bottom of the screen)
Cdc Cadence 0(20) - 299 rpm

0.0 (4.0) - 300.0 km/h

You can program the tire size.

Odometer

0.0 - 99999 km [mile]
Range of set: 10 - 2999 mm

Maximum speed

0.0 (4.0) - 300.0 km/h [0.0 (3.0) - 180.5 mph]
When the measurements are stopped

Increase the number

Decrease the number

Average Speed

0.0 - 300 km/h [0.0 - 185.0 mph]
If Elapsed Time exceeds 27 hours or Trip Distance exceeds 999.99km, Average Speed shows E. and ceases calculation.
Resetting Elapsed Time, Trip Distance, Average and Max. Speed Push the MODE button and the START/STOP button at the same time while the measurements other than Odometer, Elapsed time, Maximum Speed, Average Speed and Trip Distance are zeroed. The Odometer cannot be reset.

Trip Distance

0.00 - 999.99 km[mile]
Return to the Elapsed Time

Elapsed Time

0:0000 - 9:5959

For 2 sec.

START/STOP Computer Functions Power-Saving Function When no signal has been received for about 1 hr, the computer switches to powersaving mode and only displays the Clock. When any button is pushed or the bicycle is riden, the measurement mode comes back. Selection of The Data-display Mode In Auto-Mode you can choose between Speed or Cadence to be displayed in the top screen. Speed is initially selected in the upper dismode, play. When the computer is in press the START/STOP button. Cadence AT will now appear in the upper display. Speed will be in the lower display. Switch it back START/STOP with the same procedure. Speed Cadence
While any measurement is displayed on the screen

Setting The Clock Time

24 hour or 12 hour system is to be used with km/h or mph unit respectively. Increase the number
Return to Elapsed Time display

Return to Clock display

0:00 - 23:59 [1:00 - 12:59]
When the measurements are stopped.

Set the hour

Set the minute

Specifications

Battery/Its Life : ----------------------------- A Lithium Battery (CR2032), Approx:3 yrs. (Approx:1 hr per day usage.) Control System : ---------------------------- 4-bit 1-chip micro-computer (with a crystal oscillator) Display : -------------------------------------- Liquid crystal display Sensing System : --------------------------- No-contact magnetic sensor Range of tire circumference setting : ----- 10 mm - 2999 mm (Initial value 2096 mm) Range of Operational Temperature : ------ 0C - 40C (32F - 104F) Dimension and Weight(Computer) : ------ 38 x 54 x 17.5 mm [1-1/2 x 2-1/8 x 11/16"] / 28 g [1.0 oz] * The factory-loaded battery life might be shorter than the above-mentioned specification. * The specifications and design are subject to change without notice.

Standard Parts

Troubleshooting No display appears. Is the battery dead? Replace it and do all clear procedure. Strange data appears Do all clear procedure. Data of odometer is also erased. Measurements do not start when the START/STOP button is pushed. Is the icon ON? Turn the Auto-Mode off to enable the start or stop of the measurements by manual operation of the button. No speed or cadence data can be measured. The contacts to be short-cir(If the speed or cadence data is not displayed, have the contact cuited intermittently are located points short-circuited a few times by a metal plate. In the case on the back. that this short-circuiting is detected by the computer, the computer is considered normal and the bracket and the sensor possibly have the cause of trouble.) Is the gap between the sensor and the magnet too big? (should be within 5 mm) Speed Cadence Does the marked line of the sensor align with the center of the magnet? Adjust the position of the magnet and the sensor. Wipe the contact points of the bracket or computer clean. Is the cord broken? Even if the outside of the cord looks normal, there could be damage. Replace the bracket and sensor set with a new one. Additional troubleshooting at www.cateye.com

Limited Warranty 2-Year Warranty : Computer Head Only
(Bracket sensor and batteries are not covered under the warranty) If any trouble or damage occurs during normal use, the product computer will be repaired or replaced free of charge. Type your name, address, telephone number or e-mail address, date of purchase and the situation of trouble and send it back together with the product to the closest address below. Transportation charges shall be borne by the customer. After being repaired, the product will be shipped back to the customer.
2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn.: CAT EYE Customer Service Section Service & Research Address for North American Consumers: CAT EYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone: 303-443-4595 Toll Free: 800-5CATEYE Fax: 303-473-0006 e-mail: service@cateye.com URL: http://www.cateye.com * Accessory parts are available for the customers as shown below. #169-9400N
Bracket Sensor Kit (Rear wheel sensor)

CO.,LTD.

#169-9757N

Attachment Kit

#169-9765

Cadence Magnet

#169-9691N

Wheel Magnet

#166-5150

Lithium Battery (CR2032)

Close Open
Replacing The Battery When the display becomes dim, replace the battery. Put a lithium battery CR2032 in the computer with the (+) mark facing up. After replacing the battery, refer to "Computer Set-Up" and do an all clear operation.

Optional Parts

Maintenance To clean the computer or the attached parts, use diluted neutral detergent on a soft cloth and wipe it off with a dry cloth.

#169-9402N

Center Mount Bracket Kit (Rear wheel sensor)

#169-9403N

Bracket Sensor Kit for Aero Bar (Rear wheel sensor)

#169-9760 #169-9404N

Stem Mount Bracket Kit (Rear wheel sensor) Magnet for Composit Wheel

Ultimate Rakk, floor stand Black Dimensions Cross Disc, 700c 1 -1/8 Inch ThreBlack Windwood Dualist Carbon Cross Fork w/ Disc Carbon Cane Creek Strados Disc Wheelset 700c Black/Silver 700C HI TEN CROSS FORK 250MM IPOD WHITE ACTIVE TUNES IRIDE SPEAKER SET AHEADSET *SAS* 1" BLACK AVID BB7 DISC BRAKE FRONT 160 AVID BB7 DISC BRAKE FRONT 160 AVID BB7 DISC BRAKE FRONT 160 AVID BB7 DISC BRAKE REAR 160 AVID BB7 DISC BRAKE REAR 160 AVID BB7 DISC BRAKE REAR 160 AVID POLYGON ROTOR JUICY 160MM 6 BOLT ISO AVID ROUNDAGON ROTOR 160MM 6 BOLT ISO AVID SPEED DIAL SL V LEVERS AVID SPEED DIAL SL V LEVERS 24T/74*591424 BLACKSPIRE PRO ALLOY RING 24T AB1*1.3 OZ BODYGLIDE SKIN FORMULA CC-CD200 CATEYE ASTRALE 8 COMPUTER CATEYE ELLED HEADLIGHT CC-ED300 CATEYE ENDURO 8 COMPUTER TL-LD600BRR/RED CATEYE FLASHING T.LITE W/BAT 160-1700M*MC100W CATEYE MICRO WIRELESS COMPUTER 160-1701M*MC100W CATEYE MICRO WIRELESS COMPUTER 169-9350 H.DUTY CATEYE PART 2ND BIKE KIT CC-VL500 CATEYE VELO 5 COMPUTER DELTA AIR ZOUND 2*RECHARGABLE AH1000 TD9100*ALLEN*SL DELTA AXLERODZ HUB SKEWERS DELTA LEONARDO WALL RACK DELTA LEONARDO WALL RACK DELTA MICHEALANGELO LEAN RACK DELTA SEURAT SPACE SAVER STAND 1 1/8" BLACK FSA ORBIT X THREADLESS HEADSET 1 1/8" SILVER FSA ORBIT X THREADLESS HEADSET 1 1/8" BLACK FSA ORBIT X THREADLESS HEADSET FSA SL-K MEGAEXO CRANK/BB 10SP, 170MMTRIPLE 170MM*53/39/30 FSA SL-K MEGAEXO CRANK/BB 10SP GREENFIELD REAR MT KICKSTAND SKS2B-POLY*BLK CP BRASS INCREDIBELL BRASS DUET BELL CP BRASS INCREDIBELL BRASS SOLO BELL POLISH BRASS INCREDIBELL BRASS SOLO BELL CP BRASS INCREDIBELL BRASS SOLO BELL INCREDIBELL GRIP BELL*BRASS INCREDIBELL GRIP BELL*SILVER REFLECT*700X38C KENDA KWIKROLLR TIRE EZ*K KS-DURASA SALMN KOOL STOP ULTEGRA CART PADS PR KRUZER KING 3PC CRNK 44T W/GRD CFJ-100W 175MM LADYBUG HORN MAXXIS DETONATOR TIRE 700X25C*BLACK MAXXIS RE-FUSE TIRE 700X25C*BLACK MIRRYCLE PIVOTING MTN MIRROR RM-016*25.4MM NITTO MOUSTACHE HBAR*515MM SIL B352*25.4X560MM NITTO NORTH ROAD CROMO HBAR B352*25.4X560MM NITTO NORTH ROAD CROMO HBAR P.BIKE SPEEDEZ QR FENDERS 7017*35MM ROAD PARK P-HANDLE HEX WRENCH PH-4*4MM PARK P-HANDLE HEX WRENCH PH-5*5MM
$ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $
40.00 60.00 280.00 336.95 20.00 35.00 25.00 100.00 100.00 100.00 100.00 100.00 100.00 40.00 30.00 65.00 65.00 22.00 6.00 35.00 50.00 25.00 20.00 45.00 45.00 15.00 15.00 35.00 14.00 15.00 15.00 75.00 25.00 60.00 60.00 60.00 400.00 50.00 22.00 10.00 10.00 10.00 10.00 10.00 10.00 20.00 6.00 50.00 6.00 26.00 26.00 18.00 57.00 42.00 42.00 32.00 9.00 9.00
PARK P-HANDLE HEX WRENCH PH-6*6MM $ PARK P-HANDLE HEX WRENCH PH-6*6MM $ PARK P-HANDLE HEX WRENCH PH-8*8MM $ $ PARK RESCUE WRENCH MULTI TOOL STL-2*17-22"ADJ $ PARK TOOL ROLLING SHOP STOOL PAUL LOVE LEVERS 2 1/2 3-FINGER PR BLK $ PEDROS RIM TAPE 16MM WIDE 12 rolls $2.50ea $ $ PEDROS RIM TAPE 16MM WIDE 12 rolls $2.50$2.50ea $ PEDROS STAR NUT SETTER PEDROS TOOL Y ALLEN WRENCH 2-3 2/2.5/3MM $ PEDROS TOOL Y ALLEN WRENCH 2-3 2/2.5/3MM $ PEDROS TOOL Y ALLEN WRENCH 2-3 2/2.5/3MM $ $ PEDROS TOOL Y ALLEN WRENCH 4-6 4/5/6MM POLAR SQUEEZE THERMAL BOTTLE CRYSTAL*24 OZ $ POLAR SQUEEZE THERMAL BOTTLE BLUE*24 OZ $ POLAR SQUEEZE THERMAL BOTTLE PINK*24 OZ $ POLAR SQUEEZE THERMAL BOTTLE GOLD*24 OZ $ POLAR SQUEEZE THERMAL BOTTLE GREEN*24 OZ $ REMA 25MM (1") ROUND PATCH F1-P BOX/100 $ SMN CANTI BRAKE*FRONT IBRR550 W/ LINK $ SMN 04 XT CASS M760 11-34T ICSM7609134 9SP $ SMN 04 XT CASS M760 11-34T ICSM7609134 9SP $ SMN 105 10S BRAKE FRONT IBR5600AF74X $ SMN 105 10S BRAKE REAR IBR5600AR74A $ SMN D/A 9 BAR CON SHIFTERS ISLBS77H 9SP $ SMN DEORE UN40 BBSET 73X111MM ABBUN40C10 $ SMN DEORE UN40 BBSET 73X113MM ABBUN40C13 $ SMN PEDAL SPD OPEN ATB EPDM520L*BLACK $ SMN R440 BRAKE LEVER F/CANTI EBLR440PAL*BLK $ $ SMN R440 BRAKE LEVER F/CANTI EBLR440PA SILVR SMN R700 COMPACT DBL ROAD CRK 110X34/50T 10S*170MM $ ISMFC6600B*ENG $ SMN ULTEGRA 10 BB UNIT SMN ULTEGRA 10 CRK 52/39/30 IFC6603CX29*170 $ SMN ULTEGRA 10 F DER*1 1/8-1/4 IFD6603BSM TPL $ SMN ULTEGRA BAR CON SHIFTERS ISLBS64L 8SP $ SMN XT R DER LONG CAGE*STD IRDM751SGS $ SRAM FORCE 10 BRAKE SET TI FRONT AND REAR CALIPE $ SRAM FORCE 10 FRONT DER 31.8MM 1 1/4" $ $ SRAM FORCE 10 REAR DER CARBON HIGH FIBER SRAM PC971 CHAIN 9SP $ SRAM PC971 CHAIN 9SP $ SRAM PC991 CHAIN HOLLOW PIN 9SP $ SRAM PC991 CHAIN HOLLOW PIN 9SP $ SRAM PG-950 ROAD CASS 11-26T 00.7900.001.000*9SP $ SRAM PG-970 CASSETTE 11-34T 200-394 9SP $ SRAM PG990 CASSETTE 11-32T 200.696*9SP $ SRAM PG990 CASSETTE 11-34T 200.698*9SP $ 200-625*9SP $ SRAM ROCKET SHIFTER SHORTY SRAM X9 GRIPSHIFT SET 8spd 200.977 ESP 8SP $ SRAM X9 R DER LONG CAGE 200.294*ESP 9SP $ 200.807*9SP*PR $ SRAM XO CARBON GRIP SHIFT SET SUMMIT BELL W/COMPASS NH-406C BLACK $ SUMMIT BELL W/COMPASS NH-406C BLACK $ SUMMIT BRAKE CABLE TIPS 2.3MM SILVER*BTL/500 $ OH SAY CAN YOU HEAR $ SUMMIT CHROME U.S. FLAG BELL SUMMIT FOLDING REPAIR STAND YC-100*W/BAG*AL $ SUMMIT REG TUBE-48MM PRESTA 27X1/700X18-23C $ 27X1/700X23-28C $ SUMMIT REG TUBE-PRESTA

9.00 9.00 10.00 11.00 85.00 110.00 32.00 32.00 30.00 8.00 8.00 8.00 9.00 9.00 9.00 9.00 9.00 9.00 20.00 21.25 83.00 83.00 65.00 65.00 82.00 7.30 7.30 25.50 20.00 20.00 200.00 35.00 220.00 49.00 82.00 75.00 250.00 65.00 175.00 32.00 32.00 58.00 58.00 32.00 45.00 90.00 90.00 50.00 45.00 70.00 70.00 6.00 6.00 16.00 6.00 150.00 4.00 4.00
SUMMIT REG TUBE-PRESTA SUMMIT REG TUBE-PRESTA SUMMIT REG TUBE-PRESTA SUMMIT REG TUBE-PRESTA SUMMIT REG TUBE-PRESTA SUMMIT SHIFT CABLE TIPS 1.6MM SUMMIT SIS-SP 5MM DER HOUSING SUNRACE LIGHT ALLOY THUMB SHF TAKE A LOOK ORIGINAL MIRROR TEKTRO ORYX CROSS CANTI BRAKE TEKTRO TRIATHALON BRAKE LEVER TOPEAK JOE BLOW TURBO PUMP TOPEAK ROAD MORPH MINI PUMP TOPEAK SPEED MASTER BLASTER TOPEAK SPEED MASTER BLASTER TOPEAK SPEED MASTER BLASTER TRANZ-X SKEWER SET*ALLEN TYPE VELOCITY VELOPLUGZ SPOKE HOLE VELOX RIM TAPE * WIDE VELOX RIM TAPE * WIDE VENTURE GELBOT WATERBOTTLE VENTURE PRESSBOT COFFEE PRESS WELLGO CLIPLESS PEDAL SPD W/CAGE WHLS F.DER SHIM 1 1/8:1 1/4" WHLS F.DER SHIM 1 1/8:1 1/4" WTB ALL TERRAINASAURUS TIRE WTB CROSSWOLF RACE TIRE 700C XPEDO MTN FORCE PEDAL SS BODY XPEDO ROAD FORCE PEDAL TI BODY YELLOW RACER LEGBAND ASST COLR
27X1/700X28-32C 700X40-45C 26X1.95-2.125 26X1.50-1.90 26X1.50-1.90 SILVER*BTL/500 BLACK*25'BAG OLD SCHOOL WITH HELMET MOUNT 992AG*BLACK RX4.1 PAIR FLOOR PUMP TRP-3G W/ GAUGE TSMB-1 ROAD TSMB-1 ROAD TSMB-1 ROAD JD-061*SILVER BAG/72 #51*16MM*EACH #51*16MM*EACH 28 OZ CLEAR FOR NALGENE BOTTLES 1/2 PLATFORM 1/2 SPD F. DERAILLEUR SHIMS F. DERAILLEUR SHIMS 700X32(32/30)W W010-0204*32K CROMOLY AXLE, SPD TI AXLE, SPD FOR PANT LEGS
$ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $ $
4.00 5.00 4.00 4.00 4.00 15.00 23.00 10.00 16.00 20.00 30.00 48.00 40.00 18.00 18.00 18.00 9.00 14.00 4.00 4.00 8.99 20.00 60.00 6.00 6.00 22.00 42.00 65.00 180.00 4.00