XR2/ XR2+

ONE 1 ONE 2 ONE 3 ONE 4 ONE 5 ONE 6 ONE 7 ONE 8 am er A t ck
Intruder alarm system Operating Instructions
These operating instructions cover the following intruder system:
8SP 403 XR2+ G3 panel with built in keypad Unset system indications 8SP 404 XR2 G3 panel with built in keypad

Remote LED keypad

ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 Tamper Attack
For Clarity, the information given on setting the system, assume that all Programs use a timed or final door setting routine.
LED steady On indication LED flashing indication LED Off
o/p ARC Output to Alarm Receiving Centre

Unset system indications

An unset system will have both Day and Power indicators lit. This is a normal Day Power indication when the system is disarmed.

Internal sound

Sound description
NOTE: In general a flat beep is an indication of an incorrect key press. External devices Strobe Bell
Note: If the Power indicator goes off at any time then there is a mains supply failure at the security panel, consult your servicing organisation.

Set System indication

An active Set system will have only the Power Power indicator lit. This is an armed system indication.

issue 1 8/01

www.ukpanels.com

Operating instructions

Contents
Unset system indications Set System indication Access codes How to operate Personal Attack - - - How to unset system in alarm - - - - - Programs 1, 2 and 3 How to set the system (on program 1) - Push to Set Switch Keyswitch Set Faults during setting How to unset the system (turn off) - - How to set program1,2 or 3 - - - - - - How to Quick set - - - - - - - - - - - How to Omit zone(s) on setting system Fire Alarm How to set Chime Zones - - - - - - - Operators Program mode To exit operation at any time How to enter Operators program mode How to view the events log - - - - - - How to create/omit User 2 code - - - - How to change current user code - - - How to carry out Alarm and Walk testsServicing organisation details Quick Reference 8
Citadel XR2/XR2+ G3 Intruder system
How to unset system in alarm
Enter your code. Entering the code will turn the alarm off and the cause of the alarm will be displayed. After investigation press Reset to clear the indication.

n n n n

- - - -
FIRST ZONE IN ALARM OTHER ZONES IN ALARM

Investigate the Alarm

ALL ZONE

Strobe Off

Access codes
Note: If the alarm indication does not clear, then the system may need to be reset by the installation engineer, contact your installer for further information.
Programs 1, 2 and 3 Access codes
There are two User codes used in the system, both are 4 digit and can be set to any number from 0000 to 9999, signified by:
The user 1 and 2 codes have the same operation for testing, Setting and Unsetting, but user 1 code which is usually considered to be the Managers code has the authority to add, change or delete the user 2 code and Duress code.
The panel uses 3 Part Set routines known as Programs. In each Program the exit mode can be changed and the zone may be set up to have a different function. The examples below show how 3 typical Programs could be used in a house. Program 1 To arm all of the zones and become Set as the user leaves the property and closes the final door. Program 2 To protect the perimeter of the property in the evening and become Set after say 20 seconds. Program 3 To protect the downstairs areas of the house at night and become Set silently. The above are purely examples. The installer has the ability at the programming stage to configure all the circuits to the customers exact requirements.
User 1 code 0123 factory set User 2 code not programmed.

How to operate Personal Attack
Personal Attack buttons on the keypad are used to activate the alarm, irrespective of whether the system is armed or not. Press Simultaneously: 9 4
How to set the system (on program 1)
The green Day indicator should be showing. Enter your code number and check Day that the system is clear (none of the n n n n zone indicators 10seconds are showing). The Exit beep insistent beeps sounder will now produce an exit Day beep tone and you should leave by o/p ARC the approved Set output route. The system will Set as the beep tone stops.
How to unset the system (turn off)
On entering the premises an entry beep tone come on. Enter your code, the green Day indicator is lit. The system is unset and disarmed.

Entry beep Day

Acknowledge Day

o/p ARC Unset output

Push to Set Switch
In some systems a Push to Set switch may be fitted outside the premises near to the main exit door. This should be used to complete the setting procedure once the building has been vacated. As the switch is operated, the exit beep tone will How to set program 1,2 or 3 stop and a chime tone will be produced to The green Day indicator should be showing. acknowledge setting. Day Enter your code number and the n n n n exit beep tone will start. Press Exit beep Keyswitch Set the Prog key and ZONE 1-3 Prog Exit beep the exit tone will Your system may have been fitted with a remote keyswitch. This can be used as an alternative to stop. Press 1, Or arming the system with a code and will set or 3 for the Program 1. required 10 seconds Exit beep insistent beeps program, the Where a keyswitch is used it may be necessary sounder will on occasions to allow it to catch up with the Day beep to system. For example if the alarm was set with a o/p ARC acknowledge the code, to Unset with the keyswitch, it would have Set output program number. to be momentarily turned to Set then returned to The exit beep tone will start and you should Unset. leave by the approved route. The system will Set as the beep tone stops.

Faults during setting

If the system is not clear when you try to Set it, the sounder will produce an open zone tone and the fault will be displayed. Either re enter your code to turn off and investigate or omit the faulty zone(s) from the system.
It is important that you follow the correct procedure when setting the system. After leaving the protected area it is absolutely essential that you wait until the exit tone stops, before assuming the system has set.

How to Quick set

During the exit period (on entering User code) Day the system may be Set Set the system or quickly by pressing Set. This removes the exit time Set a Program period.
5 seconds insistent beeps Day

How to set Chime Zones

Example: To set zone 3 and 4 to chime, Press:

o/p ARC Set output

If you omit zones and require Quick Set, you will need to press Set twice.
Timeout after 5 seconds if no selection is made

Day Chime

Deselect all zones (Factory default no chime) Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 Appropriate Zone indicator is lit to show chime zone(s)
Zone n Chime selected Zone n Chime deselected
How to Omit zone(s) on setting system
Press number button to select / deselect Zone Chime
During the exit period after entering User code and selecting a Day program press Set the system or OMIT, the exit tone Set a Program and while the will stop and zones system is setting: that are about to be Omit armed will be ZONE(S) TO BE ARMED displayed. Key in Exit beep the zone number(s) to be omitted which Press the zone(s) n to be omitted will flash to confirm selection. Zone ZONE(S) TO BE OMITTED indicators which Set show steady are still about to be armed. 10 seconds Exit beep insistent beeps When the selection Day is complete press o/p ARC Set and the exit tone Set output will start. If a zone refuses to be omitted, it may be because the engineer has programmed the panel to prevent you from turning off the zone. If in doubt ask your installer for advice.

Leave chime mode

Fire Alarm
The fire zone will operate on detection of a fire, whether the system is Set or Unset, when configured as a 24 hour zone, and cause a distinctive internal sounder tone. The external sounders will pulse on and off at 2 second intervals and zone indicator will flash to attract attention.
Chime is a low security monitoring system for use when the system is Unset. When a zone that is set to chime is operated, the internal sounder will produce a low volume two stage warning tone and the Zone indicator will show. The indicator may be cancelled by pressing Reset. Chime is particularly useful in a shop to warn of a customer presence or in a house to warn that a door or particular area has been accessed. Any zone may set to be on or off chime by pressing the CHIME key and then keying in the required zone number(s). Key 0 to cancel all zones from chime. After a few seconds the system will automatically return to the Day mode.

Operators Program mode

The information below shows the programmable options available and how to change them. Once the operator program mode has been accessed, each section may be changed in any order. As each operation is completed the system will automatically return to top level of program mode.

How to view the events log
The panel can hold up to 8 previous events which can be scrolled automatically or manually. The automatic scroll starts with the newest event ( number 8) to the oldest one ( number 1).
Example: To view up to 8 previous events and thereafter to stop the event scroll, Press: Prog Chime
Note: When programming the system should be in the Day mode, with the Day and Power indicators lit.
Enter Operators program mode

View the event log

Tamper
To exit operation at any time
On pressing the Reset key you will quit the current level of operation.
Automatic event scroll Starting from event 1 to 8 To manually scroll View event (oldest event)
Zone, PA and Tamper indicators will be lit to show zone in alarm. Flashing indicates the first zone in alarm. Day indicates status of panel at the time of alarm
Quit the current function Leave Engineering menu Down one menu level
View event 2 View event 3 View event 4 View event 5 View event 6 View event 7
How to enter Operators program mode
To enter the Operators program mode the system should be in Day Prog mode with the Day and ZONE 1 - 8 Power indicator lit. Momentarily On
8 View event 8 (Newest event) Chime Resume automatic scroll

Acknowledge

Stop event scroll / view Leave program mode

Day Acknowledge Tamper

How to create/omit User 2 code
User 1 code which is usually considered to be the Managers Example: To create user 2 code 4567, Press: code has the Prog authority to add, 7 change or delete Reset the user 2 code.
Enter Operators program mode Change / omit User code (By user 1 only)

Attack

How to create/change/omit the Duress code
The Duress code is used in a hold up situation where there is pressure to Set or Unset the system. Entry of the code will allow the system to work normally but also generate a silent PA type alarm by operating the PA communicator output. The duress code in not preprogrammed and can be created.
Example: To createduress 5555, Press:

ZONE 1-4

n New code
NOTE - The sounder will produce a flat beep if code is rejected.
Enter Operators program mode Change / Omit the Duress 9 Code (By user 1 only)

To omit the user 2 code

Rising beeps ZONE 1-4 Attack

Leave program mode

New duress code
How to change current user code
You can change the current user 1 or user 2 code Example: To change user 1 for security code from 0123 to 7777, Press: reason.
Change the code of Current user (either User 1 or User 2)

Current user new code

Rising beeps ZONE 1-4
NOTE - Factory default code for User 2 is not programmed

How to carry out Alarm and Walk tests
The alarm test function allows you to test the Strobe, Bell, Low and High volume sounders of the system. The walk test function allows each detector to be checked in order to verify that they are functioning correctly.
Example: To start bell test and thereafter to stop bell test. Prog 0 Reset Reset Enter Operators program mode

0 Alarm test

Press zero to turn off options 2,3,4 and 5 before selecting a new one

Strobe test

Strobe On Bell on

3 Bell test 6

Low volume sounder High volume sounder Walk test
internal low volume sound internal high volume sound Strobe

Strobe On

x1 for zone 1 x2 for zone 2 | x4 for zone 4 flat x1 for zone 5 flat x2 for zone 6 | flat x4 for zone 8 Rapid for PA Rapid for Tamper
Appropriate zone lights are lit(latched) Zones

Exit current level

Servicing organisation details
Servicing organisation name:
Bell Time: Bell delay Area protected Zone 1 Program 1 Program 2 Program 3

Telephone number:

Date of installation:

Zone 2 Zone 3

Account Number:

Zone 4 Zone 5

Installation Date:
Zone 6 Zone 7 Zone 8 T Timed (Entry/Exit Zone) TI Time Inhibited (Access zone to keypad) I Immediate (All zones armed to give full alarm)

Quick Reference

To Set a Program

Day Entry beep Day Day

To Set the system (Program 1)

n n n n n n n n

To Un-set the system To Quick Set the system Bell

To Reset Alarm state

To Omit zones on Setting system

Exit beep

Exit beep Acknowledge

FIRST ZONE IN ALARM

OTHER ZONES IN ALARM
Set the system or Set a Program

ZONE(S) TO BE ARMED

ZONE 1-3
Set the system or Set a Program and while the system is setting
10seconds insistent beeps
Or Day Day 10 seconds insistent beeps

Exit beep Day

5 seconds insistent beeps

nvestigate the Alarm

o/p ARC Set output o/p ARC Set output
Press the zone(s) to be omitted

ZONE(S) TO BE OMITTED

The panels conform to the requirements of the European EMC and Low Voltage directives, and carries the CE mark.
Operators program mode menu map

Chime Chime

Operators Progam Mode Prog

n n n 7

To exit Operators program mode

To set Chime zone

Alarm test Change / omit User code 2 (By user 1 only) Change the code of Current user (either User 1 or User 2) View the event log

n n n n n

10 seconds insistent beeps Day
Strobe test To omit the user 2 code
Automatic event scroll Starting from event 1 to 8 For manual scroll

Zone to chime

3 Bell test
View event 8 (Newest event)

Low volume sounder

Change / Omit 9 the Duress Code (By user 1 only)

Reset Reset

View event 1 (oldest event)

High volume sounder

Resume automatic scroll
Norma nd cat ons of an Unset system

Day Power

6 n n n
Walk test Press zero to turn off options 2,3,4 and 5 before selecting a new one

A arm nd cat ons

Stop event scroll / view
Quit the current function Leave program menu Down one menu level

Bell On

Strobe Tamper / Serv ce warn ng

XR2/ XR2+

ZONE 1 ZONE 2 ZONE 3 ZONE 4 ZONE 5 ZONE 6 ZONE 7 ZONE 8 Tamper Attack
Intruder alarm system Operating Instructions
Servicing organisation details
Servicing organisation (Installer) name: ____________________________________ Telephone number: _____________________________________________________ Date of installation: _____________________________________________________ Account number: _______________________________________________________

Operating instructions

System installation
This booklet tells you how to operate your intruder alarm system. To simplify this booklet we have assumed that the alarm system has been installed by a professional intruder alarm system installer (the installer), and that the system is operated in a typical way. Aspects of your system that are not typical will be described by your installer.

Fire Zones

One or more Zones on your alarm system may have a Fire or Smoke detector connected to it. In the event of a fire the alarm system will produce a distinctive two-tone fire alarm sound, and the outside siren will pulse 2 seconds on, 2 seconds off. You should leave the premises immediately, and only re-enter when it is safe to do so. The alarm can be silenced by entering your code.
The Power indicator on the control panel or keypad will light whenever the mains power supply is present. If mains power fails then the Power indicator will go out, but the system will run from its backup battery for several hours. If the Power indicator goes out when mains power is present then a fault may have developed on Codes your system and you should contact your To operate the alarm system you will need to use installer. a code. A code is 4 digits long, and can be any number from 0000 to 9999. By default the code Warning beeps 3 but you should change is 0 Your system may produce warning beeps to this as soon as possible. inform you of a potential problem. A single beep every 5 minutes tells you that the system needs to be serviced. You should call your installer to Alarm System Operation arrange a service visit. The system will continue This booklet describes two versions of the alarm to operate correctly in all respects. system. The keypad and indicators are on a small A double beep every 5 minutes tells you that the remote keypad. You operate the alarm system by telephone line that the alarm system uses is not pressing buttons on the keypad and viewing the available or has failed. This may be due to indicators. Both alarm systems work the same someone using a telephone on the same line. If way. Both systems can be fitted with an optional this problem persists you should contact your remote keypad. installer to rectify the problem. Your alarm system will continue to operate, but it cannot Personal Attack send alarm messages via the telephone line.
If you have any questions about your intruder system, then consult your installer, see contact details on the front page.

"

Power Indicator
If you are under threat, or are being attacked, you can activate the alarm by pressing the 4 and 9 keys at the same time on any keypad. The alarm system will produce a loud alarm sound, and the external siren will be turned on.

Signalling Device

Your alarm system may have been fitted with a signalling device. This device uses the telephone line to send an alarm message to an Alarm Receiving Centre in the event of an alarm. The operator at the ARC may request the police to attend your premises.
Citadel XR2/XR2+ G3 intruder system

How to set the system

When you leave your premises you will need to set (or turn on) the intruder alarm system. 1. Before setting the system you should ensure that the premises have been completely vacated and that all doors and windows are closed. Ensure that pets do not have access to the protected areas as they can cause a false alarm. The green Day indicator should be lit. 2.
3 and check Enter your code 0 that the system is clear (none of the zone indicators are lit). The system will now produce an exit beep tone. You should leave the premises by the exit route recommended by your installer. The system will set when the exit beep tone stops. The Day indicator will go out. You should wait until you hear that the exit beep has stopped before assuming that the system has set.

Remote Keypad

Exit beeps

How to Unset the system

When you enter your premises you will need to unset (or turn off) the system. 1. Enter your premises by the route recommended by your installer. The system will produce an entry beep tone.

Entry beeps

3 , and the Key in your code 0 entry tone will stop. The green Day indicator will light.

Acknowledgement beep

If any Zone, Tamper or Attack indicator lights up then an alarm has occurred, and an intrusion may have taken place. Seek assistance before investigating further as intruders may still be on the premises. Then reset the system (refer to page 7). Note that when you enter your premises you will have a short period of time, usually 30 seconds, to key in your code. If you fail to do this the system will go into alarm. Key in your code to stop the alarm.
How to part set the system
If your installer has programmed your system for part set operation you will be able to set some zones of the system while others remain unset. Part set operation is often used at night time, and it will permit you to freely walk around the bedrooms while the living area and outside doors are protected. Your system may have 2 part-set programs called Program 2 and Program 3. 1. Before part-setting the system you should ensure that all doors and windows are closed. Ensure that pets do not have access to the protected areas. Your installer may have instructed you to use a different keypad to the one normally used to set the system. The green Day indicator should be lit. 2. 3. Enter your code 0 will start.

3. The Exit beep

Press the key. The exit tone will stop and Zone indicators 1 to 3 will light.
Or 3 to select part-set program 2 or 3. Press 2 You must now leave the protected zones. The system will set after a short time.
Note: There will be no exit beeps if silent set exit mode was programmed.

How to silence an alarm

If your system goes into alarm then be aware that intruders may be in the premises. Seek assistance before investigating the cause of the alarm. 1. Enter your code 0

External siren

The alarm will stop, and the Zone, Tamper or Attack indicators will light to show the cause of the alarm. When 2 or more indicators are lit, the flashing indicator shows the first alarm, and the steady indicators show the second and subsequent alarms. 3. You may need to cancel Police response. Your installer will provide details of how to do this. You will now need to reset the system, as described in the following section.

How To Reset After An Alarm
After any alarm you will need to reset your system so that it can be used normally. Your installer may have programmed the system to be reset by you, the installer, or by Anti-code. 1. Press the key. If the Zone, Tamper or Attack indicators all go out and the Day indicator lights then the system has been reset. If any of the indicators continue to flash then the system has been programmed to be reset by the installer. In this case you must call the installer to reset the system. If all indicators light steady (not flashing), and the keypad stops working, then the system has entered a fault-lockout. You must call the installer rectify this fault.

Strobe Off

Anti code reset
The installer may instruct you to reset the system by an Anti-code. 1. Reset Press. The system will now display a sequence of 4 numbers by using the Zone indicators. Each number will be displayed for a few seconds, the system will beep, and display the next number. You can repeat this sequence by pressing Reset again. Write down the 4 digit number and quote it to the installer 2. The installer will tell you a 6 digit anti-code. Call your installer for the anti-code. 3. Key in the 6 digit code to reset the system.

How to Omit zones

If you cannot set the alarm system because a detector is faulty and in constant alarm you may need to omit its zone from the alarm system. A zone which has been omitted cannot cause an alarm. 1. Key in your code to start the exit procedure. For more information see How to set the system or How to set program 2 or 3. Press and the exit beep tone will stop, and the indicators will display all zones being used. Press the zone numbers to be omitted n , these indicators will now flash. If a flat reject tone is produce then the zone cannot be omitted.
When you have finished press system.

to set the

10 seconds insistent beeps
How to Quick Set the system
When you set the system you will usually have about 30 seconds to exit the premises. This also means that you need to wait 30 seconds for the system to set. You can reduce this time to just 5 seconds by carrying out a second 'set' a Quick Set. 1. Key in your code to start the exit procedure. The exit beep tone will start. For more information see How to set the system, or How to set program 2 or 3. Press to Quick set the system and the exit beep tone will change to a faster, insistent, tone. The system will set in 5 seconds, and the exit tone will stop.
5 seconds insistent beeps

How to set up Chime Zone

Chime is a low security facility for use when the system is unset. It is particularly useful in a shop to warn of customers presence, or in a house to warn when a back door has been opened. When a Chime zone detects movement the system will produce a brief twotone sound, and the Zone indicator will light. To set any Zone to Chime: 1. The green Day indicator should be lit. Press the button, and the system will produce a brief chime tone, the Day indicator will flash, and the Zone indicators will light to show those Zones that are already set-up for Chime (possibly none). 2. Momentarily press the number of the zone to toggle it in and out of chime. For this example we have Zone 1 in chime and we want to de-select Zone 1 chime and select Zones 2 and 3 to chime. Press 3. 3. When you have finished using the Chime mode press

Reset Chime

How to change your User code
You should change your main code regularly to prevent potential intruders from knowing your code. 3 but this may have All codes are 4 digits long. The factory set main code is 0 been changed. 1.

Press 0 1

light and the Day indicator will go out to indicate that you are in Programming mode.
and now enter your code 2 3. The Tamper indicator will
Press 8 to select user code reprogram. The Attack and Zone indicators 1 to 4 will be lit to prompt you to enter a new code.
Key in your new code n n n n. If the code is accepted the system will produce a series of rapid beeps. If the code is rejected, for example if it is already in use, the system will produce a flat reject tone. You must go back to step 2.

Rising beeps

Press to exit programming mode. The Tamper indicator will go out and the Day indicator will light.

Example

If your code is 0123 and you wish to change it to 5678 then:
How to change your second code
Your alarm system can have a second user code. You may find it useful to set-up this second code for use by a neighbour for use when you are on holiday. The second user code operates like your user code, but it cannot be used to change or delete your code. 1. Press 0 1
and enter your code 2 3. The Tamper indicator will
Press 7 to select second code reprogram. The Attack and Zone indicators 1 to 4 will be lit to prompt you to enter a new 4 digit user code.
Key in the new second code n n n n. If the code is accepted the system will produce a series of rapid beeps. If the code is rejected, for example if it is already in use, the system will produce a flat reject tone. You must go back to step 2.
Press to exit program mode. The Tamper indicator will go out and the Day indicator will light.
If your second code is 1234 and you wish to change the code to 7890, then:
How to delete your second code
You can delete the second code to prevent it from being used. 1. Follow steps 1 and 2 of How to change your second code and press 2. Follow steps 5 of How to change your second code.
How to change the Duress code
Your alarm system can have a duress code. The Duress code is used in a hold-up situation where there is pressure to set or unset the system. The Duress code operates like your normal code but in addition it will silently send a signal to the Alarm Receiving Centre who will inform the Police. 1. Press 0 1
will light and the Day indicator will go out to indicate that you are in Programming mode.
and enter your code 2 3. The Tamper indicator
Press 9 to select Duress code programming. The Zone indicators 1 to 4 will light to prompt you for a new code.
Now enter your new duress code n n n n. If the code is accepted the system will produce a series of rapid beeps. If the code is rejected, for example if it is already in use, the system will produce a flat reject tone. You must go back to step 2.

If you need to change the duress code to 6543, then:
How to view the event log
The event log keeps a memory of the last 8 alarm events. 1.
Prog Press and enter your code 0 The Tamper indicator will light and the Day indicator will go out to indicate that you are in Programming mode.
Press. The system will display 8 alarm events in sequence, with the last (most recent) alarm first. When 2 or more indicators are lit, the flashing indicator shows the first alarm, and the steady indicators show the second and subsequent alarms. The example here shows an event where Zone 3 was the first zone in alarm followed by Zones 1 and 2. All 8 alarm events will be displayed in sequence, with a 5 seconds delay between each event. You can cause the display to pause by pressing Chime. You can also display a specific event by pressing its event number, 1 to 8. Press to exit the event log and press again to exit program mode. The Tamper indicator will go out and the Day indicator will light.

Reset Reset

How to test your alarm system
You should check that your alarm system still works correctly by periodically carrying out the alarm system tests described here.
How to test the Strobe, External Siren and Internal Sounders

1. Press 0 1

and enter your 4 digit user code 2 3. The Tamper indicator
Press 0 to select alarm test mode. The Attack indicator lights to indicate that you are in alarm test mode.
Strobe test Press 2 to test the strobe light. This is normally mounted on the external siren. It should produce a bright flash at a rate of 1 flash every few seconds. Press 0 to stop this test.

Strobe On

Siren (Bell) Test Press 3 to test the external siren, this should produce a loud alarm sound. Press 0 to stop this test.
Sounder Low Volume Test Press 4 to test the Low volume sounder. This should produce a low volume alarm sound. Press 0 to stop this test. Sounder High Volume Test Press 5 to test the High volume sounder. This should produce a high volume alarm sound. Press 0 to stop this test.
Internal low volume sound
Internal high volume sound

Walktest Press 6 to carry out a walktest. Walk around your property, and in turn cause each of the detectors to go into alarm. Also, open and close all door and windows that are protected by the system. For each detector (including door or window sensor) that is activated the system will produce a series of beeps, and the associated zone indicator will light. Press 0 to stop this test.
IMPORTANT: Do not test any Personal Attack buttons during the walktest, since these are still active and will cause a full alarm.
If any of the alarm tests fail, or you are unsure of the correct procedure, contact your installer. 4. Press to exit Alarm test and press again to exit program mode. The Tamper indicator will go out and the Day indicator will light.
External siren Time:_____________________________ Siren delay______________________________ Area protected Zone 1 Zone 2 Zone 3 Zone 4 Zone 5 Zone 6 Zone 7 Zone 8 T = Timed (Entry/Exit - Zone) TI = Time Inhibited (Access zone to keypad) I = Immediate (All zones armed to give full alarm) Zone name Program 1 Program 2 Program 3
For Technical Support : 0999
The panels conform to the requirements of the European EMC and Low Voltage directives, and carries the CE mark.
This is a premium rate line, calls are charged at 50 pence per minute Novar ED&S The Arnold Centre Paycocke Road Basildon SS14 3EA

4188-731 issue 2_04/03