Reviews & Opinions
Independent and trusted. Read before buy Citizen Watch H460!

Citizen Watch H460

Manual

Preview of first few manual pages (at low quality). Check before download. Click to enlarge.
Manual - 1 page  Manual - 2 page  Manual - 3 page 

Download (English)
Citizen Watch H460, size: 402 KB
Instruction: After click Download and complete offer, you will get access to list of direct links to websites where you can download this manual.

About

About Citizen Watch H460
Here you can find all about Citizen Watch H460 like manual and other informations. For example: review.

Citizen Watch H460 manual (user guide) is ready to download for free.

On the bottom of page users can write a review. If you own a Citizen Watch H460 please write about it to help other people.

 

[ Report abuse or wrong photo | Share your Citizen Watch H460 photo ]

User reviews and opinions

<== Click here to post a new opinion, comment, review, etc.

No opinions have been provided. Be the first and add a new opinion/review.

 

Documents

doc1

English

Names of Components
NO: Reception result SET: Indicated when a time difference has been set 0: Indicated when no time difference has been set Hour hand
RX: Reception standby H,M,L: Reception level/reception result Button (B)
WThis watch is a radio wave watch that W
receives the standard time radio wave transmitted in Germany.
This radio wave watch is equipped with a regular automatic reception function that sets the time and date by automatically receiving radio waves twice a day at 3:00 AM and 4:00 AM, and a free reception function that allows the time to be set arbitrarily by receiving radio waves. A time difference can also be set in 1 hour units based on German standard time.

Minute hand

Crown Second hand Button (A)
The design may differ slightly depending on the model.
This watch only receives the standard time radio wave transmitted in Germany during radio wave reception. It is unable to receive radio waves of countries other than Germany. When using the watch in a location that has a different time difference than that of Germany, set the time difference by referring to the section entitled, 5. Time Difference Correction Function. If the standard time radio wave transmitted in Germany is received after setting the time difference by another method, the time will return to German standard time.
WPlease use this watch afterW charging sufficiently by placing in light.
If the second hand of the watch is moving at two-second intervals while the watch is in use, this indicates that the watch is insufficiently charged. Use the watch after first recharging by placing the watch under direct sunlight for about 8 hours. To ensure that this Eco-Drive Radio Wave Watch is used comfortably without stopping, it is recommended to try to keep the watch fully charged at all times.
WPlease confirm the following before usingW the watch.
RX:Reception standby NO: Reception result H,M,L: Reception level / reception result
Check the movement of the second hand.
Second hand moving at 1second intervals
Check the reception result.
Press button (A) (located at the 4:00 position) once.
When the second hand has pointed to a reception result (H, M, L)
The standard time radio wave has been received properly. The watch can now be used.
Second hand moving at 2-second intervals Button (A)
When the second hand has pointed to reception result (NO) Recharge the watch by placing under direct sunlight
Second hand moving at 1-second intervals
Perform radio wave reception by referring to Free Receptiondescribed in the section on Important Points Regarding Radio Wave Reception.
WImportant Points Regarding Radio Wave ReceptionW
The two ways to receive radio waves that are ordinarily used consist of Regular Automatic Reception and Free Reception. When receiving radio waves, first remove the watch from your wrist, face the 9:00 position on the watch towards the radio wave transmitter station, and place the watch in a stable location that facilitates reception of radio waves such as in front of a window. Since the watch uses a directional antenna, moving the watch while reception is in progress may prevent radio waves from being properly received. When reception is completed, the second hand returns to one-second interval movement. Do not move the watch until radio wave reception is completed.
[Regular Automatic Reception]
The watch sets the time and date by automatically receiving radio waves at the predetermined times of 3:00 AM and 4:00 AM each day.
<Confirmation of Reception>
Check the reception result to determine whether or not radio waves have been received properly by pressing button (A) located at the 4:00 position once. If the second hand points to H, M or L, this indicates that radio waves have been received properly. The watch can now be used. If the second hand points to NO at the 11:00 position, this means that radio waves were unable to be received properly. If this happens, perform radio wave reception using the Free Reception function.

[Free Reception]

The Free Reception function lets you receive radio waves at any time. Use this function when the reception environment has changed or in other cases when radio waves are unable to be received by Regular Automatic Reception.
<Reception Procedure> (1) Press button (A) located at the 4:00 position for about 2 seconds, and then release the button after the second hand has moved to the RX (12:00) position. (2) The second hand then moves to H, M or L indicating that reception is in progress. (3) When reception is completed, the second hand moves from H, M or L and returns to one-second interval movement.

[Reception Standby] [Reception in Progress] Reception level (H, M, L)

T SE SE T

WWhen Storing in a Dark Location for a Long Period of TimeW
If the watch is stored in a location out of the light for a period of one week or more, the Power Save Function of the watch is activated and the watch stops. Even though the watch is in the Power Save mode, it still continues to perform Regular Automatic Reception and the watch continues to keep the correct time internally. However, the time may not be able to be corrected as a result of being unable to receive radio waves depending on the manner in which the watch is stored. When resuming use of the watch after storing for an extended period of time, cancel the Power Save function by placing the watch in the light and then perform Free Reception to correctly set the time and date. * Refer to 7. A. Power Save Function for information on the Power Save function.

[Reception Completed]

RX (Reception Standby)
Button (A) Second hand returns to onesecond interval movement
* Refer to 3. Receiving Radio Waves for further details on the procedure for receiving radio waves.

CONTENTS

1. Features.... 15 2. Before Using.... 16 A. Radio Wave Receiving Function <For Good Reception> <Locations where Reception may be Difficult> 3. Receiving Radio Waves... 18 A. Reception Modes B. Position of the Second Hand during Reception C. Confirmation of Reception Result D. Reception Level and Reception Result E. General Reference for Receiving Areas 4. Manually Setting the Time and Date... 27 <Screw Lock-Type Crown> A. Correcting the Second Hand and Minute Hand
B. Correcting the Month and Year (No. of Years Since Leap Year) C. Correcting the Hour Hand and Date 5. Time Difference Correction Function.. 38 <Time Difference Setting Procedure> <Setting the Time Difference in this Case> <Confirmation of Time Difference Setting> <Canceling Time Difference> 6. Solar-Powered Watch Handring Notes.. 45 <For Optimum Use of this Watch> <Try to Keep the Watch Charged at all Times> 7. Unique Functions of Solar-Powered Watches.. 46 A. Power Save Function <Power Save> <Canceling Power Save> B. Insufficient Charge Warning Function C. Overcharging Prevention Function
8. General Reference for Charging Times of Solar-Powered Watches. 52 9. Solar-Powered Watch Handling Precautions.. 54 10. Setting the Reference Position... 56 A. Checking the Reference Position B. Setting the Reference Position <Changing the Mode when Setting the Reference Position> 11. All-Reset.... 60 A. All-Reset Procedure B. Setting the Reference Position after All-Reset 12. Troubleshooting... 64 13. Precautions.... 66 14. Specifications.... 72

D. Reception Level and Reception Result
During the standard time radio waves are being received, the second hand waits at the reception level position corresponding to the reception state to indicate the reception level. Following reception, the reception result can be confirmed by pressing button (A) once.
Reception Position of second level hand H 12 seconds position Reception level during reception When radio wave reception level is high When radio wave reception level is moderate When radio wave reception level is low ----------
E. General Reference for Receiving Areas
The following provides a general reference for those areas where the watch is able to receive standard time radio waves. However, these areas may vary depending on the time, seasonal variations and weather (presence of lighting, etc.). Since this map only provides a general reference of the standard receiving areas, it may not apply in some particular locations even within the range shown on the map.
Standard time radio wave transmitter station DCF77 Location of transmitter station Mainflingen, Germany (25 km southeast of Frankfurt) General reference for areas where radio waves can be received Radius of about 900 km from radio wave transmitter station (radio waves may not be able to be received in the vicinity of Lake Leman)
Reception result after reception When radio waves were received at a high reception level When radio waves were received at a moderate reception level

9 seconds position

6 seconds position 55 seconds position
When radio waves were received at a low reception level When reception has failed
Although the standard time radio waves used by radio wave watches are transmitted continuously 24 hours a day, transmission may be interrupted for reasons such as maintenance and inspections. This watch will continue to keep the correct time at an accuracy of within 15 seconds per month even if it is unable to receive standard time radio waves.

4. Manually Setting the Time and Date
This watch allows the time and date to be set manually when radio waves are unable to be received.
Oslo Hamburg Hamb Berlin Paris Budapest Marseilles Rome Beograd Barcelona Naples
<Screw-Lock Type Crown> If the crown of your watch is of the screw-look type, operate the crown after first loosening the screw locking mechanism by turning the crown to the left. When finished operating the crown, turn the crown to the right while pushing in after having returned it to the normal position and tighten securely. After having manually corrected the time and date or after having corrected the time difference, make sure to securely tighten the screw locking mechanism of the crown after returning it to the normal position. Since the watch will continue to be in the hour hand and date correction mode or time difference correction mode, etc. if the screw locking crown is tightened immediately after completion of hand movement, the hour hand will advance causing the set time and so forth to be incorrect.

Warsaw

The correction mode can be changed by operating the crown and buttons in the manner shown below.
[Normal Display] Button (B) Crown pulled out to first position Crown pulled out to second position Time correction (minute hand /second hand)
A. Correcting the Second Hand and Minute Hand
<Correction Procedure> (1) Pull the crown out to the second position. The second hand rapidly moves forward or backward to the 0 seconds position and stops. If the second hand is not stopped at the 0 seconds position, set the reference position by referring to Setting the Reference Position. (2) Turn the crown to set the minute hand. When the crown is turned (one click) to the right, the second hand makes one revolution while moving forward (in the clockwise direction), and the minute hand advances by one minute. When the crown is turned (one click) to the left, the second hand makes one revolution while moving backward (in the counter-clockwise direction), and the minute hand moves back by one minute. Turning the crown continuously (by two clicks or more) causes the second hand and minute hand to move continuously. Turn the crown to the left or right to interrupt continuous movement of the hands.

When the crown is turned continuously to the left, the hour hand moves continuously in the backward (counter-clockwise) direction. When the hour hand makes two revolutions, the date changes by one day. Continuously advance the hour hand until the correct date is displayed. Turn the crown to the left or right to interrupt continuous movement of the hour hand. The date changes between about 10:00 PM and 3:00 AM. In the case the month is set to a month with less than 31 days, a non-existent date is automatically passed by and the watch indicates the first day of the following month even if the date is changed from the 30th to the 31st. (4) Turn the crown to set the hour hand. When the crown is turned (one click) to the right, the hour hand advances by one hour (clockwise direction). When the crown is turned (one click) to the left, the hour hand moves back by one hour (counter-clockwise direction). Note: When correcting the time, set the time while paying attention to AM and PM. The time when the date changes is 12:00 AM. (5) Press button (A) for 2 seconds.
The time difference setting data is reset and the second hand returns to the 0 position. However, the hour hand and date indicate the corrected time and date. Note: Once the time and date have been set (after the hour hand has finished moving or the date has finished changing), always make sure to press button (A) for 2 seconds within 10 seconds. If the watch is left as is without pressing button (A), the time difference will be set and the next time radio waves are received, the time resulting from adding the amount time used to correct the time to the current time will be displayed. (6) Press button (B) once. The watch returns to the normal time display. This completes the procedure for manually setting the time and date.
<Times when Calendar Changes During Normal Use> Month and year: Changes at 12:00:00 AM on the first day of the month Date: Changes between around 10:00 PM and 3:00 AM
5. Time Difference Correction Function
This watch is equipped with a time difference correction function that lets you set a time difference in one hour units with respect to the received German standard time. When radio waves are received after having set a time difference, the time is displayed after correcting the set time difference. A time difference display monitor is provided that indicates whether or not a time difference is set with the second hand.
<Time Difference Setting Procedure> (1) Put the crown in the normal position. (2) Press button (B) once. The second hand moves to the SET or 0 position to indicate that the watch has entered the time difference correction mode. (3) Turn the crown to correct the time difference. A When the crown is turned (one click) to the right, the hour hand moves forward (clockwise) by one hour. B When the crown is turned (one click) to the left, the hour hand moves backward (counter-clockwise) by one hour.

Although the hour hand moves continuously when the crown is rotated continuously (by two clicks or more), move the hour hand one hour at a time to ensure that the time difference is corrected reliably. Turn the crown one click to the left or right to stop continuous movement of the hour hand. (4) Once the time difference has been set, the second hand moves to the SET position. The second hand moves to the 0 position if a time difference has not been set. (5) Press button (B) once after setting the time difference. This completes the procedure for setting a time difference. The second hand returns to one-second interval movement. Notes: Correct the time difference while being careful not to mistake AM, PM or the date. Time difference can be corrected for 10 seconds after pressing button (B) or for 10 seconds after the hour hand has stopped moving after correcting the time difference. The watch automatically returns to the normal display if the crown has not been operated for 10 seconds after pressing button (B) or 10 seconds after correcting the time difference.
Example: Setting to London time when the time in Germany is 10:10 AM The time difference between London and Germany is -1 hour. When the time in Germany is 10:10 AM, the time in London is 9:10 AM.

[Normal Display]

[Time Difference Correction Mode]

Button (B)

Press button (B) once
Returns automatically after 10 seconds or when button (B) has been pressed 1 second interval movement Turn the crown to set the time difference
<Setting the Time Difference in this Case> (1) Put the crown in the normal position. (2) Press button (B) once. The second hand moves to the 0 position indicating that the watch has entered the time difference correction mode. (3) Turn the crown to the left to turn back the hour hand by one hour. Once a time difference has been set, the second hand moves to the SET position. (4) After setting the time difference, press button (B) once. This completes setting of the time difference. The second hand returns to onesecond interval movement.
<Confirmation of Time Difference Setting> When the crown is put in the normal position and button (B) is pressed once, the second hand moves to the SET or 0 position to indicate the time difference setting status. Note: If the crown is turned while the time difference setting status is displayed, the hour hand will move and a time difference will be set that causes the time to change. To return to the normal display, either press button (B) again or simply wait for 10 seconds.
When the second hand points to SET: Time difference is set When the second hand points to 0: Time difference is not set.
<Canceling Time Difference> Cancel the time difference by moving the hour hand in the opposite direction of that when the time difference was set. When the time difference has been set ahead (forward direction): Turn back the hour hand by the number of hours it was advanced. When the time difference has been set back (reverse direction): Advance the hour hand by the number of hours it was turned back. (1) Put the crown in the normal position and press button (B) once. The second hand moves to the SET position and the watch enters the time difference correction mode. (2) Turn the crown to move the hour hand until the second hand points to 0. When the crown is turned (one click) to the right, the hour hand turns forward (clockwise) by one hour, and when turned (one click) to the left, the hour hand turns backward (counter-clockwise) by one hour. The date setting changes if the hour hand is moved in the same direction as when the time difference was set. Always make sure to move the hour hand in the opposite direction in which the time difference returns to zero.

Handling of Secondary Battery Never attempt to remove the secondary battery from the watch. If the secondary battery must unavoidably be removed, store it out of the reach of small children to prevent accidental swallowing. If the secondary battery should happen to be swallowed, consult a physician immediately and seek medical attention. Only Use the Specified Secondary Battery Never use an secondary battery other than the genuine secondary battery used in this watch. Even if another type of secondary battery is installed in the watch, the watch structure does not permit its operation. In cases in which a different secondary battery such as a silver battery is forcibly installed in the watch and charged, overcharging may occur that will eventually cause the secondary battery to rupture. This can result in the risk of the watch being damaged or injury to the wearer. When the secondary battery is replaced, always make sure to use the specified secondary battery.
Replacing the Secondary Battery Unlike ordinary silver batterys, the secondary battery used in this watch does not have to be periodically replaced due to repeated charging and discharging.
10. Setting the Reference Position
Check the reference position if the watch does not indicate the correct time even after having received radio waves. In the case the reference position (0 position/12:00 position), which serves as the reference for all watch functions, has shifted, check the reference position of each hand using the procedure described below. Setting the Reference Position
Depress button (B) for 10 seconds or more
Indicates a position between 31 and 1
<Reference Position of Each Hand and Date> Second hand, minute hand, hour hand: 12:00 position (0:00:00) Date: Between 31 and 1 Set the reference position if any of the hands or date do not indicate the reference position.
A. Checking the Reference Position
(1) Press button (B) for at least 10 seconds with the crown in the normal position, and once the second hand begins to move rapidly, release button (B). The hour hand moves to the reference position after the second hand and minute hand have moved to the reference position. The hour hand continues to advance until the date is displayed between 31 and 1. Since the date changes in coordination with the hour hand, it displays a position between the 31 and 1 and stops. (2) When button (B) is pressed after reference position is indicated, the hands rapidly return to the current time. Alternatively, the watch will automatically return to the current time if the buttons or crown are not operated for 30 seconds or more.

B. Setting the Reference Position
(1) Press button (B) for at least 10 seconds with the crown in the normal position, and when the second hand begins to move rapidly, release button (B). The hour hand moves to the reference position after the second hand and minute hand have moved to the reference position. (2) Pull out the crown to the first position and turn the crown to set the date between 31 and 1 and set the hour hand to 12:00.
Turning the crown continuously (by two clicks or more) causes the hour hand to move continuously. When the hour hand makes two revolutions, the date changes by one day. Continuously advance the hour hand until the date is displayed between 31 and 1. Turn the crown to the left or right to interrupt continuous movement of the hour hand. After the date displays between 31 and 1, slowly turn the crown until the hour hand indicates 12:00. (3) Pull out the crown to the second position and turn the crown to set the second hand and minute hand to 00 minutes 00 seconds. Turning the crown (by one click) causes the second hand to advance by one second, and the minute hand to advance in coordination with the second hand. Turn the crown to the right or left to set the second hand and minute hand at 00 minutes 00 seconds. Turning the crown continuously (by two clicks or more) causes the second hand and minute hand to move continuously. Turn the crown to the left or right to interrupt continuous movement of the second hand and minute hand. (4) Return the crown to the normal position and press button (B). Each hand and the date rapidly return to the current time. * This completes setting of the reference position. After setting the reference position, always make sure to perform free reception before using the watch.
<Changing the Mode when Setting the Reference Position>
[Normal Operation] Button (B)
Press button (B) or returns automatically after 30 second
Press button (B) for 10 seconds or more [Reference Position Correction Mode] (correction of hour hand and date) Crown to first position Crown to second position
[Reference Position Confirmation Mode]
[Reference Position Correction Mode] (correction of second and minute hands)

Crown to normal position

Crown to first position

11. All-Reset

The watch display may become abnormal due to the effects of static electricity or a strong shock. If this happens, perform the all-reset procedure and then set the reference position.

B. Setting the Reference Position after All-Reset
(1) Align the second hand and minute hand at 00 minutes 00 seconds. Turning the crown (by one click) causes the second hand to advance by one second, and the minute hand to advance in coordination with the second hand. Turn the crown to the right or left to set the second hand and minute hand at 00 minutes 00 seconds. Turning the crown continuously (by two clicks or more) causes the second hand and minute hand to move continuously. Turn the crown to the left or right to interrupt continuous movement of the second hand and minute hand. (2) Push in the crown from the second position to the first position, set the date between 31 and 1 and set the hour hand to 12:00. Turning the crown continuously (by two clicks or more) causes the hour hand to move continuously. When the hour hand makes two revolutions, the date changes by one day. Continuously advance the hour hand until the date is displayed between 31 and 1. Turn the crown to the left or right to interrupt continuous movement of the hour hand. After displaying the date between 31 and 1, slowly turn the crown until the hour hand indicates 12:00.

A. All-Reset Procedure

(1) Pull out the crown to the second position. The second hand rapidly moves to the reference position stored in memory and stops. (2) Press buttons (A) and (B) simultaneously.
This completes the all-reset procedure. Always make sure to set the reference position according to B. Setting the Reference Position after All-Reset after performing the all-reset procedure. Note: Do not push in the crown to the normal position until the reference position has been set after performing the all-reset procedure.
Note: If the crown is accidentally pushed in too far to the normal position when the crown is pushed in from the second position to the first position, since this will end setting of the reference position causing the hands to move normally, it will not be possible to set the reference position for the hour hand and date. If the crown has returned to the normal position, set the reference position by referring to 10. B. Setting the Reference Position. Alternatively, repeat the all-reset procedure again. (3) Return the crown to the normal position. When the reference position is set after performing the all-reset procedure, the second hand begins one-second interval movement a few seconds after the crown is returned to the normal position. Do not pull out the crown until the second hand begins one-second interval movement. (4) Perform free reception or set the time and date manually.

<Cautions Following All-Reset> After performing the all-reset procedure, the time will not be displayed correctly due to the reference position having shifted unless the reference position is set with the crown at both the first and second positions. Always make sure to set the reference position. After performing the all-reset procedure, the time shown after setting the reference position is 0:00 AM. When setting the time manually, set both the time and date while paying attention to AM and PM so that the time is set correctly.

12. Troubleshooting

Radio Wave Reception Function: Try checking the following when you think a problem has occurred.
Problem Watch does not begin reception Unable to receive radio waves (even within a receivable area) Check Items Corrective Actions Unable to receive radio waves even though second hand points to RX Does the second hand still Wait until reception is completed indicate a reception level of H, (until the second returns to one-secM or L during reception? ond interval movement) Check the reference position. If the reference position is not correct, refer to the section entitled, 10. Setting the Reference Position of this manual and reset the reference position. Check whether or not a time difference has been set. Correctly reset the time difference if only the hour hand has shifted in one hour units.
Does the second hand move to Continuously depress button (A) and RX: Reception standby? release when the second hand points to the RX position. Are there objects that block radio waves or generate noise nearby? Are radio waves attempted to be received away from a window? Try receiving radio waves while facing the 9:00 position of the watch towards a window while avoiding objects that block radio waves or generate noise. Try changing the direction, location and angle of the watch several times so that the second hand points to a reception level to find the location at which radio waves are received easily. (Refer to the sections entitled, For Good Reception and Locations where Reception may be Difficult of this manual.
Time does not match Has the reference position time service even been set correctly? though radio wave can Has a time difference been be received set?

13. Precautions

CAUTION: Water-resistance performance There are several types of water-resistant watches as shown in the following table. The unit "bar" is roughly equal to 1 atmosphere. * WATER RESIST (ANT) xx bar may also be indicated as W.R. xx bar.
Indication Dial WATER RESIST or no indication WR 50 or WATER RESIST 50
WR 100/200 or WATER RESIST 100/200
For correct use within the design limits of the watch, confirm the level of waterresistance of your watch, as indicated on the dial and case, and consult the table.

Examples of use

Case (Case back) WATER RESIST(ANT)
WATER RESIST(ANT) 5 bar or WATER RESIST(ANT) WATER RESIST(ANT) 10 bar/20 bar or WATER RESIST(ANT)
Specifications Water-resistant to 3 atmospheres Water-resistant to 5 atmospheres Water-resistant to 10/20 atmospheres
Minor exposure to water (washing face, rain, etc.)
Moderate exposure to Marine sports (skin water (washing, kitchen diving) work, swimming, etc.)
Scuba diving (with air tank)
Operation of the crown or button with moisture visible

OK OK OK

NO OK OK

NO NO OK

NO NO NO
Water-resistance for daily use (to 3 atmospheres): This type of watch is water-resistant to minor exposure to water. For example, you may wear the watch while washing your face; however, it is not designed for use underwater. Upgraded water-resistance for daily use (to 5 atmospheres): This type of watch is waterresistant to moderate exposure to water. You may wear the watch while swimming; however, it is not designed for use while skin diving. Upgraded water-resistance for daily use (to 10/20 atmospheres): This type of watch may be used for skin diving; however, it is not designed for scuba or saturated diving using helium gas.
If seawater enters the watch, place the watch in a box or plastic bag and immediately take it in for repair. Otherwise, pressure inside the watch will increase, and parts (crystal, crown, buttons, etc.) may come off.

CAUTION:

Keep your watch clean. Leaving dust and dirt deposited between the case and crown may result in difficulty in pulling the crown out. Rotate the crown while in its normal position from time to time to loosen dust and dirt and then brush it off. Dust and dirt tend to be deposited in gaps in the back of the case or band. Deposited dust and dirt may cause corrosion and soil your clothing. Clean the watch occasionally.

Be sure to use the watch with the crown pressed in (normal position). If your watch has a screw-type crown or button, be sure to tighten the crown completely. Do NOT operate the crown or button with wet fingers or when the watch is wet. Water may enter the watch and compromise water-resistance. If the watch is used in seawater, rinse with fresh water afterward and wipe with a dry cloth. If moisture has entered the watch, or if the inside of the crystal is fogged up and does not become clear within a day, immediately take the watch to your dealer or Citizen Service Center for repair. Leaving the watch in such a state will allow corrosion to form inside.

Cleaning the Watch

Use a soft cloth to wipe off dirt, perspiration and water from the case and crystal. Use a soft, dry cloth to wipe off perspiration and dirt from the leather band. To clean a metal, plastic, or rubber watchband, wash away dirt with water. Use a soft brush to remove dust and dirt jammed in the gaps in the metal band. NOTE: Avoid using solvents (thinner, benzine, etc.), as they may damage the finish.
Operating environment Use the watch within the operating temperature range specified in the instruction manual. Using the watch where temperatures are outside the specified range may result in deterioration of functions or even stoppage of the watch. Do NOT use the watch in places where it is exposed to high temperature, such as in a sauna. Doing so may result in a burn. Do NOT leave the watch in a place where it is exposed to high temperature, such as the glove compartment or dash-board of a car. Doing so may result in deterioration of the watch, such as deformation of plastic parts. Do NOT place the watch close to a magnet. Timekeeping will become inaccurate if you place the watch close to magnetic health equipment such as a magnetic necklace, a magnetic latch of a refrigerator door,handbag clasp or the earphone of a mobile phone. If this has occurred, move the watch away from the magnet and reset the time. Do NOT place the watch close to household appliances that generate static electricity. Timekeeping may become inaccurate if the watch is exposed to strong static electricity, such as is emitted from a TV screen. Do NOT subject the watch to a strong shock such as dropping it onto a hard floor.

Avoid using the watch in an environment where it may be exposed to chemicals or corrosive gases. If solvents, such as thinner and benzine, or substances containing such solvents come in contact with the watch, discoloration, melting, cracking, etc. may result. If the watch comes in contact with mercury used in thermometers, the case, band or other parts may become discolored.

Periodical inspections

Your watch requires inspection once every two or three years for safety and long use. To keep your watch water resistant, the packing needs to be replaced regularly. Other parts are required to be inspected and replaced as necessary. Ask for Citizen geuine parts during replacement.

14. Specifications

1. Model: H460 2. Type: Analog solar-powered watch 3. Timekeeping accuracy: Within 15 seconds per month on average (when worn at normal temperatures of +5C to +35C /41F to 95F and when not receiving radio waves) 4. Operating temperature range: -10C to +60C /14F to 140F 5. Display functions: Time: Hours, minutes, seconds (the hour hand advances every 2 minutes) Date 6. Additional functions: Radio wave receiving function (regular automatic reception, free reception, recovery automatic reception) Reception status display function Reception result confirmation function Reception level display function Time difference setting function
Solar power generation function Power save function Insufficient charge warning function 7. Continuous operation times: Time until watch stops without charging after being fully charged: : Approx. 2 years (when power save function is operating) : Approx. 6 months (when power save function is not operating) Insufficient charge warning display to stopped: Approx. 6 days 8. Battery: Secondary battery (rechargeable battery), 1 pc. * Specifications are subject to change without notice.

 

Tags

SRU1010 10 HT-C5800 Majesty400-2006 Video KDL-65W5100 P2450H MAX-WS730 1175C BDL3231C Mf 9545 Xpressmusic FOR PC 220 CPL I845 MD853 MP280 4core1333-fullhd Voice Installazione 1 5 CD-RW4u USB Smart TEC HVR-HD1000P Es 350 Review LAV73530 STI462BF1 VR 285 R530-JA05 RC6500 Olympus IS-2 All-IN-ONE Urc-2560 FP91E ERB3500X Pqdsb 48780 Asko 1474 MX4PER XVM-H65 KX-TDE200 SPH-S5350 Omnibook 510 1500 VD 535-1998 M365 T Iphone XR-CA400 E1255W LBT-LX7 LCX-19C 0 Plus 10 E ZFU228WO DS6321-2 Engines 9500D Quad 12L 01021609 Roomba 500 Kenwood A998 Behringer HB01 2000 E Color 300 MT-03 SP-A600B V-AMP 3 DVD-HR777 TU909 WA65205 AG-V8520 Office P5B-VM 1050E Scan Dmctz8 L1900E-BF Silver Lego 7133 M405E YZ250F-2008 Dvdr3595H CCD-TR81 VN-7600PC Stavic Lbp5300 Vision L1952S-BF BX1930N Remote X-drive II Leica R4S Voyager 835 GX-300 47LH7000 GW73E-WB 665-7436 KV-29XL71K P2270HN NV-XYZ88 P4P8X Controller

 

manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding

 

Sitemap

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101