8. CHINESE

Owners manual Mode demploi Manual de instrucciones CHINESE
Thank you for purchasing the Clarion DPH7500z. Please read this owners manual in its entirety before operating this equipment. Check the contents of the enclosed warranty card and keep it carefully with this manual. The operating instructions are not provided with this manual. For the operating instructions, refer to the owners manual of the source unit.

Contents

1. 2. 3. 4. PRECAUTIONS.... 2 IDENTIFICATION OF PARTS... 3 FEATURES..... 4 FUNCTIONS OF DPH7500z... 5 Functions common to each mode... 5 Easy-mode functions... 6 Professional-mode functions... 8 INSTALLATION.... 10 CONNECTIONS... 11 SYSTEM EXAMPLES.... 13 SPECIFICATIONS.... 14

5. 6. 7. 8.

DPH7500z
DIGITAL GRAPHIC & PARAMETRIC EQUALIZER / DSP / CROSSOVER PROCESSOR MODULE EGALISEURS GRAPHIQUE ET PARAMTRIQUE NUMRIQUES / DSP / DIVISEUR DE FRQUENCES ECUALIZADOR GRFICO Y PARAMTRICO/PROCESADOR DE SONIDO DIGITAL/MDULO PROCESADOR DE RED DIVISORA CHINESE / CHINESE / CHINESE CHINESE / CHINESE / CHINESE

1. PRECAUTIONS

1. This unit does not operate independently. The unit must be used with a source unit that has a cable connection for CeNET wire bound (sold separately). 2. The DPH7500z can easily be damaged by moisture, high temperatures or high humidity. Keep the inside of the car clean and well ventilated. 3. Never subject the DPH7500z to strong shocks or open its case. Doing so may result in damage. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help. 4. Use a soft, dry cloth to wipe dirt off the DPH7500z. Never use a hard cloth or thinners, alcohol, etc. For tough dirt, apply some cold or lukewarm water to a soft cloth and wipe off the dirt gently. 5. When the source unit is switched to the traffic announcement or PTY interrupt reception while using the DPH7500z, the effect from DPH7500z doesnt work.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. INFORMATION FOR USERS:. CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

Clarion Co., Ltd.

1998/10 (CL/ToK)
All Rights Reserved. Copyright 1998: Clarion Co., Ltd. Printed in Japan / Imprim au Japon / Impreso en Japn / CHINESE

GP-970B 280-7263-00

Be sure to unfold and read the next page. Veuillez dplier et vous rfrer la page suivante. Cercirese de desplegar y de leer la pgina siguiente.
2. IDENTIFICATION OF PARTS / PRINCIPALES PICES IDENTIFICACIN DE PARTES / CHINESE
2. IDENTIFICATION OF PARTS DPH7500z
1 CeNET input/output terminal Connect the CeNET cable.
Equipment to this terminal is not specified.

7. CHINESE

Accessories
9 Name plate. 1 sheet RCA cable.. 2 pieces CeNET cable.. 1 piece Ground lead.. 1 piece Mounting bracket.. 2 pieces Cord clamp. 3 pieces Canoe clip.. 4 pieces Mounting screw. 4 pieces Cable clip.. 3 pieces
2 Front RCA terminals Connect the RCA cable. 3 Rear RCA terminals Connect the RCA cable. 4 Subwoofer RCA terminals Connect the RCA cable. 5 Exclusive terminal for digital signal output No used. 6 Digital signal input terminal Connect the digital optical fiber cable.

After connection, be sure to fix it with the cable clip.
7 Reset switch When no sound is heard, press this switch. Note: Pressing the reset switch performs the system check. 8 Cable clip insertion holes Insert the cable clip in this hole and fix the digital optical fiber cable.

3. FEATURES

Accessories / Accessoires / Accesorios / CHINESE
s Switchable Subwoofer Output (Stereo/Mono) and Adjustable Line Level Subwoofer Output s Selectable Subwoofer Low Pass Frequency and High Pass Frequency s 4V/6ch Gold-Plated RCA Line Level Output, 4 Optical Digital Inputs and 1 Optical Digital Output < Easy mode > s 12 Pre-Programed and 6 User Programmable Sound Field Memories s 7 Adjustable Sound Field Parameters s 5 Seating Position Memories s 7 Band Digital Graphic Equalizer s 6 Pre-Programed and 6 User Programmable Grapic Equalizer Memories < Pro mode > s 6 Pre-Programed and 6 User Programmable Space Equalizer Memories s 3 Adjustable Space Equalizer Parameters s 3 Band Front and Rear Independent Digital Parametric Equalizer s 6 Front and 6 Rear Pre-Programed Parametric Equalizer Memories

4. FUNCTIONS OF DPH7500z

With the DPH7500z, you can enjoy the DSP and equalizer effects by simulating the sound field using the easy menu with simple operation (easy mode), and also by simulating the sound field by adjusting the sound according to the width of the car interior (professional mode). Choose either easy mode or professional mode to adjust the sound field and sound quality. The following major functions are available on the DPH7500z: Functions common to each mode Spectrum analyzer display, auto loudness, etc. Easy mode Graphic equalizer function, DSP function, etc. Professional mode Space equalizer function, parametric equalizer function, etc. In this manual, graphic equalizer is hereafter referred to as G.EQ, space equalizer referred to as S.EQ, and parametric equalizer referred to as P.EQ.

Test-tone Output

Test tones can be output in the following order to check the speaker connections:
FRONT-LEFT FRONT-RIGHT REAR-LEFT REAR-RIGHT WOOFER-LEFT WOOFERRIGHT ALL(all speakers) OFF(no sound)

Title Input

You can assign and display titles for the DSP, G.EQ, S.EQ and P.EQ settings you have set.

4V preout

The preout voltage is raised to 4 V, providing characteristics that are resistant to noise during signal transmission. Note: Since noise or sound distortion may occur when an external amplifier is connected to this unit, keep the amplifier gain at a lower level.
Digital signal input terminal
Since 4 digital input signal terminals are provided with this unit, up to 2 units with digital signal output terminals (such as a CD changer) can be connected. Notes: When the DPH7500z and a unit with digital signal output terminal are connected with the digital optical fiber cable, and the digital optical fiber cable is disconnected, no sound is heard. Reconnect the digital optical fiber cable. If you want to listen to music from an analogue input, disconnect the digital optical fiber cable and perform a system check by operating the source unit.
Functions common to each mode
7-band spectrum analyzer display
Spectrum analyzer display of 7 bands is possible.
Auto Loudness Adjustments
You can vary the amount of compression between 0 and 10 without changing the loudness.

Subwoofer Adjustments

The following adjustments can be made if a subwoofer is connected: 1. You can set the speakers to: OFF, MONO and STEREO. 2. You can set the subwoofer volume to: 0 to 14 3. You can set the low-pass filter frequency to: 50Hz, 80Hz or 120Hz.
The slope of the low-pass filter is 24dB/oct.

High-pass Adjustments

You can select the frequency of the high-pass filter from Through, 50Hz, 80Hz and 120Hz.
The slope of the high-pass filter is 18dB/oct.

DPH7500z

Easy-mode functions
G.EQ effect ON/OFF switching
<G.EQ (Graphic Equalizer) functions>
4. IMPACT; Low and high frequencies emphasized. 5. SMOOTH; Medium and high frequencies reduced. 6. FLAT; Original sound.
You can turn the sound quality effect of the G.EQ ON or OFF by operating the buttons of the source unit.
Selection of the basic G.EQ menus
6 basic G.EQ menus are stored in the DPH7500z. You can select an appropriate sound quality according to the music. The basic G.EQ menus are as follows: 1. BASS BOOST; Low frequencies emphasized. 2. HIGH BOOST; Medium and high frequencies emphasized. 3. ACOUSTICAL; Medium frequencies (vocals) emphasized.

Editing the G.EQ

You can adjust the sound quality using the G.EQ menus as you like. The settings for the basic G.EQ menus are shown in the following table. The adjustment range of each frequency is between -12dB and +12dB.
G.EQ memory (User memory)
You can store 6 kinds of sound quality into the memory which are edited on the basis of the basic G.EQ menus.
Graphic equalizer parameter (dB) 100Hz ++2 +4 +200Hz -+1 +0 400Hz +2 -2 +4 +1 -1kHz 0 +4 +6 +3 -3kHz 0 +3 +5 +5 -12kHz 0 +4 +1 +5 -2 0
Equalizer setting 1. BASS BOOST 2. HIGH BOOST 3. ACOUSTICAL 4. IMPACT 5. SMOOTH 6. FLAT

50Hz +0 +4 +2 0

DSP effect ON/OFF switching

<DSP functions>

You can select an appropriate sound field according to the music. The basic DSP menus are as follows: BASIC 1 1. HALL: Large concert hall. 2. CHURCH: Church with a vaulted ceiling. 3. STADIUM: Large stadium without roof or walls. 4. LIVEHOUSE: Live performance hall, larger than a jazz club. 5. DISCO: Disco with strong bass. 6. JAZZCLUB: Jazz club with a low ceiling. BASIC 2 1. DOME: Indoor sports arena. 2. CHAMBER: Large, echoing hall. 3. PARK: Vast outdoor area. 4. THEATER: Movie or drama theatre. 5. STUDIO: Listening room in a home. 6. BGM: Vocals cut.

You can turn the sound field effect of the DSP ON or OFF by operating the buttons of the source unit.
Setting of the listening position
You can select one of the preadjusted listening positions according to the seat position. The following 6 listening positions are available: FULL SEAT, FRONT-RIGHT, FRONT-LEFT, FRONT, REAR and PASS.
Fine-tuning the Listening Position
The time taken for the sound to leave the speaker and reach you can be fine-tuned to create a natural sound field, no matter where you are sitting in the car.
Selection of the sound field (DSP) menus
12 basic DSP menus are stored in the DPH7500z.
Easy-mode functions Editing the DSP
You can adjust the sound field using the DSP menus as you like. The DSP parameters and their contents are as follows: EFFECT: Adjusts the percentage of reflected sound. INITIAL DELAY: Adjusts the distance between sound source and reflecting surfaces. REAR MIX: Adjusts the ratio of the direct sound output from the rear speaker. REVERB TIME: Adjusts reverberation length. ROOM SIZE: Adjusts expansion. HIGH: Adjusts the percentage of high frequencies in reverberations. LIVENESS: The sense of the rooms dynamics can be adjusted. The settings for the basic DSP menus and the adjustment ranges are shown in the following table.
About the sound field system
The DPH7500z divides the sound field into three systems: reverberation, early-reflection and B.G.M. The reverberation system is the part of the sound field where reverberating sound is vivid, while the early-reflection system is the part of the sound field where reflected sound is emphasized. DSP menus for the reverberation system: HALL, CHURCH, DOME, CHAMBER DSP menus for the early-reflection system: STADIUM, LIVEHOUSE, DISCO, JAZZCLUB, PARK, THEATER, STUDIO DSP menus for the B.G.M system: B.G.M Notes: There are some parameters that cannot be adjusted, depending on the sound field system. The reverberation system cannot adjust ROOM SIZE and LIVENESS parameters. The early-reflection system cannot adjust REVERB TIME and HIGH parameters. The B.G.M system can adjust only the EFFECT parameter.

DSP memory (User memory)

You can store 6 sound fields into the memory which, are edited on the basis of the basic DSP menus.
Initial setting Sound field 1. HALL 2. CHURCH 3. STADIUM 4. LIVEHOUSE 5. DISCO 6. JAZZCLUB 1. DOME 2. CHAMBER 3. PARK 4. THEATER 5. STUDIO 6. B.G.M Adjustment range
EFFECT 50% 50% 50% 50% 50% 50% 50% 50% 50% 50% 50% 100% 0 to 100% 0 to 100ms 0 to 100% 0.1 to to 10 0.3 to 10s 0.1 to 1 50ms 95ms 85ms 20ms 3ms 1ms 65ms 25ms 100ms 1ms 1ms 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 100% 2.0 2.0 2.2.0 2.0 2.0 2.5 7.0s 4.2s 0.5 0.5

DSP parameter

INITIAL DELAY REAR MIX ROOM SIZE LIVENESS REVERB TIME 2.5s 9.5s HIGH 0.5 0.5

BASIC 1 BASIC 2

Professional-mode functions <S.EQ (Space Equalizer) functions>
S.EQ effect ON/OFF switching
You can turn the sound pressure distribution compensation effect of the S.EQ ON or OFF by operating the buttons of the source unit.

Editing the S.EQ menus

You can adjust the sound pressure distribution on the basis of the basic S.EQ according to the car type. The S.EQ adjustment contents are as follows: DIFFUSE Compensates for spacial impression. CAR WIDTH Compensates for the width of the cars interior (lateral direction). CAR LENGTH Compensates for the length of the cars interior (longitudinal direction). The adjustable range of the S.EQ menus are 1 to 10 for each item.
Selection of the S.EQ menus
6 basic S.EQ menus are stored in the DPH7500z according to the car type. The basic S.EQ menus are as follows: 1. SEDAN-L (Large-scale sedan) 2. SEDAN-S (Small-scale sedan) 3. WAGON-L (Large-scale wagon) 4. WAGON-S (Small-scale wagon) 5. 1BOX-L (Large-scale van) 6. 1BOX-S (Small-scale van) The settings of DIFFUSE, CAR WIDTH and CAR LENGTH for each basic S.EQ menu is the center value (5) that meets each car type.
S.EQ memory (User memory)
You can store 6 kinds of sound pressure distribution into the memory which, are edited on the basis of the basic S.EQ menus.
Professional-mode functions
P.EQ effect ON/OFF switching
You can turn the transmission frequency characteristics compensation effect of the P.EQ ON or OFF by operating the buttons of the source unit.
<P.EQ (Parametric Equalizer) functions>
Selection of the P.EQ menus
6 basic P.EQ menus are stored in the DPH7500z according to the car type and the speaker installation position. The different car types and the speaker installation positions are as follows:
Vehicle type 1. Sedan 2. Sedan 3. Wagon 4. Wagon 5. 1Box (Van) 6. 1Box (Van)
front: 2WAY rear: Rear parcel 2. SEDAN front: FULL rear: Rear door 3. WAGON front: 2WAY rear: Beside the luggage 4. WAGON front: FULL rear: Rear door 5. 1BOX (Van) front: 2WAY rear: Beside the luggage 6. 1BOX (Van) front: FULL rear: Equivalent to rear door The settings of the basic P.EQ menus are as follows:
BAND 2 2kHz/F, 1/Q, -4dB/G 1.25kHz/F, 5/Q, 0dB/G 800Hz/F, 3/Q, -4dB/G 125Hz/F, 5/Q, -12dB/G 1kHz/F, 3/Q, -8dB/G 800Hz/F, 1/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G 1.25kHz/F, 3/Q, -4dB/G 630Hz/F, 3/Q, -4dB/G 1.25kHz/F, 3/Q, -8dB/G 500Hz/F, 5/Q, -5dB/G BAND 3 5kHz/F, 1/Q, -4dB/G 8kHz/F, 5/Q, 0dB/G 8kHz/F, 1/Q, -5dB/G 1.25kHz/F, 5/Q, 0dB/G 10kHz/F, 1/Q, -6dB/G 8kHz/F, 5/Q, 0dB/G 1.6kHz/F, 3/Q, 0dB/G 2kHz/F, 7/Q, +3dB/G 8kHz/F, 5/Q, 0dB/G 80Hz/F, 3/Q, +3dB/G 8kHz/F, 5/Q, 0dB/G

1. SEDAN

Parametric Equalizer Parameter
Channel Front Rear Front Rear Front Rear Front Rear Front Rear Front Rear BAND 1 250Hz/F, 3/Q, -8dB/G 250Hz/F, 3/Q, -10dB/G 250Hz/F, 7/Q, -10dB/G 80Hz/F, 7/Q, +3dB/G 250Hz/F, 3/Q, -8dB/G 250Hz/F, 3/Q, -8dB/G 250Hz/F, 7/Q, -8dB/G 125Hz/F, 3/Q, -8dB/G 125Hz/F, 5/Q, -4dB/G 250Hz/F, 1/Q, -6dB/G 250Hz/F, 3/Q, -4dB/G 250Hz/F, 3/Q, -8dB/G
400Hz/F, 7/Q, -10dB/G 1.25kHz/F, 7/Q, -8dB/G
F; Center frequency (Hz), Q; Q curve, G; Gain(dB)
Professional-mode functions Editing the P.EQ menus
You can compensate for the frequency characteristics using the basic P.EQ according to your car type. The P.EQ adjustment contents are as follows: Channel selection Select the channel to be compensated (front or rear). Selection of center frequency Select the center frequency that you want to compensate from the range of 20Hz to 20kHz. (1/3 octave step, 31 points) Selection of Q-curve Set the sharpness of the Q-curve to one of the parameters: 1, 3, 5, 7 and 20. Gain adjustment Adjust the gain (output level) in the range of 12dB to +12dB. (1dB step, 25 points) About the compensation of frequency characteristics See Figure 1 concerning the relationship of the center frequency, Q-curve (Q) and gain.
Level (dB) Q curve (Q) F Q= f
P.EQ memory (User memory)
You can store 6 frequency characteristics into the memory, which are edited on the basis of the basic P.EQ menus.

Gain (G) f

Frequency curve Center frequency (F) Frequency (Hz) Figure 1
About the Q-curve (Q) For the Q-curve (Q), setting larger values makes the curve sharper, setting smaller values makes the curve flatter. (Figure 2) Selecting the Q-curve (Q) opposite to the frequency curve to be compensated makes the frequency characteristics flat.

Q curve (Q)

Q curve; 20

Q curve; 1 Figure 2

5. INSTALLATION
1. Before starting, be sure to disconnect the batterys negative terminal to prevent accidents due to short-circuits. 2. Location Consider safety and operability when selecting a place for installation. Avoid the following.
Locations where the unit will hamper driving. Locations where the unit could injure passengers if the car stops suddenly. Locations exposed to direct sunlight or hot air from the heater, etc. Locations where the unit may be exposed to rain or water.
3. Be sure to use the included screws and brackets. Screws other than those supplied could damage the unit.

Case Case

Damage

8mm max.

4. When drilling holes in the dashboard, etc., be sure to check beforehand that there are no harnesses or other wires on the inside.
Installation example (Installing the unit under the drivers seat)
Note: Please read this chapter referring to 4. INDENTIFICATION OF PARTS at the beginning of this manual.
1. Attach the mounting brackets 5 to the sides of the DPH7500z using the screws 8 provided. 2. Select the location on the floor mat. Drill holes in the floor mat to match the positions of the holes in the mounting brackets 5. 3. Insert the canoe clips 7 from the rear of the floor mat and install the DPH7500z.

There are three mounting holes on each side of the DPH7500z. Select the appropriate holes to match to the installation location.
PPPPPPPPPPPP @@@@@@@@@@@@ ,,,,,,,,,,,, PPPPPPPPPPPP @@@@@@@@@@@@ ,,,,,,,,,,,, PPPPPPPPPPPP @@@@@@@@@@@@ ,,,,,,,,,,,, PPPPPPPPPPPP @@@@@@@@@@@@ ,,,,,,,,,,,, PPPPPPPPPPPP @@@@@@@@@@@@ ,,,,,,,,,,,,

6. CONNECTIONS

How to make wirings

1. CeNET Cable

Orient the CeNET 5 cable in the direction shown in the figure and insert it until it is locked in position. To remove the CeNET cable, pull it by lightly grasping the slide cap A in your fingers.
1 RCA cable (3) Connect it to the source units front input terminals (grey) to use the source units built-in amplifier or to the amplifiers front input terminals. 2 RCA cable (3) Connect it to the source units rear input terminals (black) to use the source units built-in amplifier or to the amplifiers rear input terminals. 3 RCA extension cable (sold separately) Connect it to the subwoofer amplifier. 4 CeNET cable (4) Connect it to the source unit, CD changer or MD changer. 5 Digital optical fiber cable (sold separately) Connect it to the source unit, CD changer or MD changer. 6 Ground lead (5) Connect it to vehicle chassis ground.

CAUTION

Wire the CeNET cable so that there is minimal tension in the cable, and the connection part will not come off. To extend the CeNET cable, use either CCA520 (98.4/2.5m) or CCA-521 (23.6/0.6m) (both are separately sold CeNET extension cables.).

2. RCA Cable

Attach the supplied name plate 2 on the RCA cable to show where to connect it. After checking where to connect it from the name plate, connect the RCA cable.
Do not remove the insulating cap of the RCA cable that is not to be connected, to prevent short-circuit. Fix the connection part of the RCA cable with insulating tape B so that it will not
come loose and disconnect.

4. Ground lead

Tighten the small terminal of the ground lead E together with the mounting bracket 5, and connect the large terminal to the metal part of the car body using the car screw D. If grounding is not achieved, noise results.
3. Digital Optical Fiber Cable
When you connect the digital optical fiber cable to the digital input terminal or to the digital output terminal, firmly insert it until it is locked in position. Connect the black slid cap side to the digital input terminal of the DPH 7500z. Note: Do not bend the digital optical fiber cable through a loop smaller than 1 (3cm) in radius. Doing so will greatly reduce perfomance.

E 5 D 8

Digital optical fiber cable (Black slide cap side)
After connecting, fasten the cable using the included cable clip 9. One cable clip can fix up to 2 digital optical fiber cables.

To remove the digital optical fiber cable, pull it by lightly grasping the slide cap C of the cable in your fingers.

7. SYSTEM EXAMPLES

System with external power amplifier and DSP

"

System with internal power amplifier and DSP

" % 5 7

1 Source unit compatible with CeNET connection 2 CD changer compatible with CeNET connection 3 4-channel power amplifier For connection with the front/rear speakers. 4 2-channel power amplifier For connection with the subwoofer speakers. 5 CeNET cable (provided with the CD changer) Using this cable, connect the DPH7500z to the CD changer. 6 CeNET cable (provided with the DPH7500z) Using this cable, connect the DPH7500z to the source unit. 7 Digital optical fiber cable Using this cable, connect the DPH7500z to the CD changer. 8 RCA cable (provided with the DPH7500z) Using this cable, connect the DPH7500z to the 4-channel power amplifier for the front/rear speakers, or connect the DPH7500z to the front /rear line out terminal of the source unit. 9 RCA cable Using this cable, connect the DPH7500z to the 2-channel power amplifier for the subwoofer speaker. ! Front speakers " Rear speakers # Subwoofer speakers $ RCA cable for front/rear line out Connect this cable to the DPH7500z. % RCA cable for non-fader line out This is not used for this system. Note: The longest wiring length of the CeNET cable is less than 65.62ft (20m). When you connect the CeNET cable, be careful not to exceed the wiring length of 65.62ft (20m).

8. SPECIFICATIONS

q S/N ratio:.. 107 dB (digital input) 100 dB (analogue input) q Frequency response:. 10 Hz to 20 kHz (1 dB) q Separation:.. 100 dB (digital input) 97 dB (analogue input) q Harmonic distortion:.. 0.003% (digital input)(1 kHz) 0.003% (analogue input)(1 kHz) q Voltage gain:.. 2.5 dB (Volume max : 4V pre-out) q Analogue input:.. 1.5 VRMS (Max.) q Digital input:.. 44.1 kHz sampling frequency, 16-bit digital audio data q A/D conversion:.. 20-bit linear, 64 times oversampling q D/A conversion:.. 20-bit linear, 8 times oversampling q DSP: Basic:.. 12 modes User:.. 6 modes q Graphic equalizer (7 bands): Basic:.. 6 modes User:.. 6 modes q Space equalizer: Basic:.. 6 modes User:.. 6 modes q Parametric equalizer:. 3 bands x 2 (independent front/rear) Center frequency:.. 20 Hz to 20 kHz, 1/3 octave steps, 31 points Q curve:.. 1 to 20 GAIN:.. 12 dB Preset:.. 6 types q Auto loudness:.. on/off q Subwoofer: Voltage gain:.. +12 dB (max. woofer volume) LPF cut off frequency:.. Through, 50 Hz, 80 Hz, 120 Hz LPF slope:... 24 dB/oct q Front / Rear: HPF cut off frequency:.. Through, 50 Hz, 80 Hz, 120 Hz HPF slope:.. 18 dB/oct q Power supply voltage:.. DC 14.4V (10.8V to 15.6V), negative ground q Power consumption:.. 560 mA q External dimensions:. 9-1/16 (W) x 1 (H) x 6-11/16 (D) [230 (W) x 25 (H) x 170 (D)mm] q Weight:... 2.091lb. (0.95 kg)