Flip Down Panel

English English
This unit uses a flip-down structure that makes possible large-size displays.

CAUTION

When opening and closing the FLIP DOWN PANEL, be careful not to catch your fingers. They could be injured. 1. Always use this unit with the FLIP DOWN PANEL closed. 2. Do not force operations or use this device abnormally when opening or closing the FLIP DOWN PANEL. 3. Do not use the FLIP DOWN PANEL as a tray to place objects on when it is open.
4. When closing the FLIP DOWN PANEL, do not press the [OPEN] button. 5. Strong impacts to the operating or display section can cause damage or deformation. 6. If the FLIP DOWN PANEL does not open fully, gently open it with your hand.
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THE COMPACT DISC PLAYER and MINI DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.

Handling Compact Discs

Use only compact discs bearing the mark. or Do not play heart-shaped, octagonal, or other specially shaped compact discs. Some CDs recorded in CD-R/CD-RW mode may not be usable. Do not use compact discs that have large scratches, are misshapen, cracked, etc. Use of such discs may cause misoperation or damage. To remove a compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may damage the disc or cause breakdown of the internal mechanism.
Preset channel indication (1 to 6) Disc number indication (1 to 12)

Handling

INFORMATION FOR USERS:. CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played. Therefore, do not leave them for a long time in the car. New discs may have Ball-point pen some roughness around the edges. If Roughness such discs are used, the player may not work or the sound may skip. Use a ballpoint pen or the like to remove any roughness from the edge of the disc. Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player.

Performs category scan while in the SIRIUS mode. When the button is pressed and held, preset scan is performed.
Adjust the volume by turning the knob clockwise or counterclockwise. Use the knob to perform various settings.

[RPT] button

Perform repeat play. When this button is pressed and held, disc repeat play is performed.
Stores a station into memory or recall it directly while in the SIRIUS mode.
Repeat play while in the CD mode.

[Z+] button

Use the button to select one of the four types of sound characteristics already stored in memory.

[SCN] button

Perform scan play for 10 seconds of each track while in the CD mode.

[a], [d] button

Press the button to selects a station.

[BND] button

Move the next disc in increasing order.
[a], [d] [DIRECT] [ ] [SCN] [RPT] [RDM] [DN], [UP] [I] [D] [T] [P/A]

[SW-VOL] button

Adjust sub woofer volume. The volume is adjusted in the range 6.
Perform scan play for 10 seconds of each track. Disc scan play is performed when the button is pressed and held.
Play or pause a CD while in the CD mode.
What is Sirius Satellite Radio?
Sirius is radio the way it was meant to be: Up to 100 new channels of digital quality programming delivered to listeners coast to coast via satellite. That means 50 channels of completely commercial-free music. Plus up to 50 more channels of news, sports, and entertainment from names like CNBC, Discovery, SCI-FI Channel, A&E, House of Blues, E!, NPR, Speedvision and ESPN. Sirius is live, dynamic entertainment, completely focused on listeners. Every minute of every day of every week will be different. All 50 commercial-free music channels are created inhouse and hosted by DJs who know and love the music. Do you like Reggae? How about Classic Rock or New Rock? Sirius has an array of choices spanning a vast range of musical tastes including the hits of the 50s, 60s, 70s, & 80s as well as Jazz, Country, Blues, Pop, Rap, R&B, Bluegrass, Alternative, Classical, Heavy Metal, Dance and many others. From its state-of-the-art, digital broadcasting facility in Rockefeller Center, New York City, Sirius will deliver the broadest, deepest mix of radio entertainment from coast to coast. Sirius will bring you music and entertainment programming that is simply not available on traditional radio in any market across the country. Its radio like youve never heard before. So Get Sirius and Listen Up! For more information, visit siriusradio.com.

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas.
G When the CD/MD/DVD changer is connected
For details, see the section CD/MD changer operations. For the DVD changer, refer to the Owners Manual provided with the DVD changer.
When the button is pressed and held, switches the disc titles or track titles while in the MD changer mode. When the button is pressed and held, switches the user titles or track titles, etc. while in the CD changer mode.

5. DCP

The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car.
Be sure to close the HOLD FLAP for safety when removing the DCP.

Attaching the DCP

1. Insert the right side of the DCP into the main unit. 2. Insert the left side of the DCP into the main unit.

Removing the DCP

1. Press the [FNC] button for 1 second or longer to turn off the power. 2. Deeply push in [OPEN] button to unlock the flip down panel.
If the flip down panel does not open fully, gently open it with your hand.

DCP 1.

3. Pull the DCP toward you and remove it. The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. If the FLIP DOWN PANEL is kept open, the DCP may drop due to vibration of the car. This results in damage to the DCP. So close the FLIP DOWN PANEL or remove the DCP to store into the case. The connector connecting the source unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc. Note: If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.

4. Close the HOLD FLAP.

HOLD FLAP
6. REMOTE CONTROL (Optional)
Receiver for remote control unit
Operating range: 30 in all directions Signal transmitter

Remote control unit

[FUNC] [ ],[ ] [DUAL ZONE] [ ] [ ],[ ] [BAND]
[ISR] [MUTE] [SCN] [RPT] [DISP] [RDM]

Inserting the Batteries

1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2. Insert the AA (SUM-3, IECR-6/1.5V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover. Notes: Using batteries improperly can cause them to explode. Take note of the following points: When replacing batteries, replace both batteries with new ones. Do not short-circuit, disassemble or heat batteries. Do not dispose of batteries into fire or flames. Dispose of spent batteries properly.

Sub display

Clock display

Main display

Once selected, the preferred display becomes the display default. When a function adjustment such as volume is made, the screen will momentarily switch to that functions display, then revert back to the preferred display several seconds after the adjustment. When you have entered a title in a CD, it appears in the sub display. If you have not entered a title, NO TITLE appears in the title display instead. For information on how to enter a title, refer to the subsection Entering titles in section Operations Common to Each Mode.

Selecting a mode

1. Press the [FNC] button to change the operation mode. 2. Each time you press the [FNC] button, the operation mode changes in the following order: Radio mode SIRIUS mode CD mode CD changer mode MD changer mode DVD changer mode TV mode AUX mode Radio mode.
External equipment not connected with CeNET is not displayed.
Setting the Z-Enhancer Plus
This unit are provided with 4 types of sound tone effects stored in memory. Select the one you prefer.
The factory default setting is Z+ OFF.
Each time you press the [Z+] button, the tone effect changes in the following order:
Z+ OFF B-BOOST IMPACT EXCITE CUSTOM Z+ OFF. B-BOOST : bass emphasized IMPACT : bass and treble emphasized EXCITE : bass and treble emphasized mid de-emphasized CUSTOM : user custom Z+ OFF : no sound effect
The factory default setting is B<Q 1>.(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the [A-M] button several times until the function mode is reached.
Adjusting the treble (Gain, Frequency)
This adjustment can be performed when the ZEnhancer Plus is set to CUSTOM. 1. Press the [A-M] button and select TREBLE. 2. Turning the [ROTARY] knob clockwise emphasizes the treble; turning it counterclockwise attenuates the treble.
The factory default setting is T<G 0>. (Adjustment range: 6 to +6)

Adjusting the tone

Press the [A-M] button and select the item to adjust. Each time you press the [A-M] button, the item changes as following order: GWhen B-BOOST is set B-BOOST BAL 0 FAD 0 Last function mode. GWhen IMPACT is set IMPACT BAL 0 FAD 0 Last function mode. GWhen EXCITE is set EXCITE BAL 0 FAD 0 Last function mode. GWhen CUSTOM is set BASS TREBLE BAL 0 FAD 0 Last function mode. GWhen Z+ OFF is set BAL 0 FAD 0 Last function mode.

3. Press the [d] or [a] button to select T<F 10>. Turninng the [ROTARY] knob clockwise or counterclockwise to select the frequency.
The factory default setting is T<F 10>.(Adjustment 10 kHz/15 kHz)
4. When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the balance

1. Press the [A-M] button and select BAL 0. 2. Turning the [ROTARY] knob clockwise emphasizes the sound from the right speaker; turning it counterclockwise emphasizes the sound from the left speaker.
The factory default setting is BAL 0. (Adjustment range: L13 to R13)
Adjusting the bass (Gain, Frequency, Q-curve)
This adjustment can be performed when the ZEnhancer Plus is set to CUSTOM. 1. Press the [A-M] button and select BASS. 2. Turning the [ROTARY] knob clockwise emphasizes the bass; turning it counterclockwise attenuates the bass.
The factory default setting is B<G 0>. (Adjustment range: 6 to +6)
3. When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the fader

1. Press the [A-M] button and select FAD 0. 2. Turning the [ROTARY] knob clockwise emphasizes the sound from the front speakers; turning it counterclockwise emphasizes the sound from the rear speakers.
The factory default setting is FAD 0. (Adjustment range: F12 to R12)
3. Press the [d] or [a] button to select B<F 60>. Turninng the [ROTARY] knob clockwise or counterclockwise to select the frequency.
The factory default setting is B<F 60>.(Adjustment 60/100/200 Hz)
4. Press the [d] or [a] button to select B<Q 1>. Turninng the [ROTARY] knob clockwise or counterclockwise to select the Q-curve.

Radio Operations

FM reception
For enhanced FM performance the tuner includes signal actuated stereo control, Enhanced Multi AGC, Impulse noise reduction curcuits and Multipath noise reduction circuits.
Adjusting the Z-Enhancer Plus
1. Press the [Z+] button and select the Z-Enhancer Plus mode to adjust. 2. Press the [A-M] button and turning the [ROTARY] knob clockwise adjusts in the + direction; tuning it counterclockwise adjusts in the direction. GWhen B-BST 0 selected, you can adjust the bass in the range of 3 to 3. GWhen IMPACT 0 selected, you can adjust the bass and treble in the range of 3 to 3. GWhen EXCITE 0 selected, you can adjust the bass and treble in the range of 3 to 3.

Dimmer control

You can setting the dimmer control on or off.
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select SCROLL. 3. Turn the [ROTARY] knob clockwise or counterclockwise and select ON or OFF. G ON: To scroll automatically. G OFF: To scroll just 1 time when the title was changed or the title key was pressed. 4. Press the [T] button to return to the previous mode.
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select DIMMER. 3. Turn the [ROTARY] knob clockwise to ON or counterclockwise to OFF. 4. Press the [T] button to return to the previous mode.

AUX function

This system has an external input jack so you can listen to sounds and music from external devices connected to this unit.
Selecting AUX IN sensitivity
Make the following settings to select the sensitivity when sounds from external devices connected to this unit are difficult to hear even after adjusting the volume.
The factory default setting is MID.
Adjusting the display contrast
You can adjust the display contrast to match the angle of installation of the unit.
The factory default setting is 5. (Adjustment level:1to 8)
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select CONTRAST. 3. Turn the [ROTARY] knob clockwise or counterclockwise to adjust the contrast. 4. Press the [T] button to return to the previous mode.
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select AUX SENS. 3. Turn the [ROTARY] knob clockwise or counterclockwise as needed and select from HIGH, MID or LOW. 4. Press the [T] button to return to the previous mode.

Setting the clock

1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select CLOCK. 3. Press the [ ] button.
4. Press the [a] or [d] button to select the hour or the minute. 5. Turn the [ROTARY] knob clockwise or counterclockwise to set the correct time.
The clock is displayed in 12-hour format.

Entering MESSAGE INFORMATION
Message up to 30 characters long can be stored in memory and displayed for CD, CD changer and TV stations.
* The factory default setting is WELCOME TO CLARION.
6. Press the [ ] button to store the time into memory. 7. Press the [T] button to return to the previous mode. Note: You cannot set the clock when it is displayed with only the ignition on. If you drain or remove the cars battery or take out this unit, the clock is reset. While setting the clock, if another button or operation is selected, the clock set mode is canceled.
Turning the screen saver function on or off
This unit is provided with the screen saver function which allows you to show various kinds of patterns and characters in the Operation Status indication area of the display in a random order. You can turn on and off this function. If the button operation is performed with the screen saver function on, the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display.
The factory default setting is SS.
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select INPUT. 3. Press the [ ] button. 4. Press the [a] or [d] button to move the cursor. 5. Press the [D] button to select a character. Each time you press the [D] button, the character changes in the following orders: Numbers Symbols Capital letters Numbers 6. Turn the [ROTARY] knob to select the desired character. 7. Repeat step 4 to 6 to enter up to 30 characters for message. 8. Press and hold the [ ] button for 2 seconds or longer to store the message in memory and cancel input message.
Setting the button illumination
Press the [COLOR] button to select a color type. Each time you press the [COLOR] button, the type changes in the following orders: CLR SCAN RED MANDARIN ORANGE AMBER YELLOW Y-GREEN LIME GREEN D-GREEN USER CLR SCAN GSetting CLR SCAN mode As selecting CLR SCAN, the color automatically changes in the following orders: CLR SCAN RED MANDARIN ORANGE AMBER YELLOW Y-GREEN LIME GREEN D-GREEN USER CLR SCAN
The factory default setting is CLR SCAN. During change the colors name not appear. After 3 second the color change to the other.
1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select SCRN SVR. 3. Press the [ ] button. 4. Turn the [ROTARY] knob clockwise or counterclockwise to select the setting. Each time you turn the [ROTARY] knob, the setting changes in the following order: OFF SS MESSAGE 5. Press the [ ] button to store the setting. 6. Press the [T] button to return to the previous mode.

The following illustration presents one of the patterns which are shown when the screen saver function is turned on.
GSetting USER mode The factory default setting is R>8 G>3. As selecting USER, press and hold the [COLOR] button 1 second or longer R>8 G>3 appears in the display. 1. Press the [a] or [d] button to move the cursor. 2. Turn the [ROTARY] knob clockwise or counterclockwise to select from 0 to 8. 3. Press and hold the [ ] button for 2 seconds or longer to store the color in memory and cancel setting mode.

Clearing titles

1. Select and play a CD in the CD changer or tune in to a TV station for which you want to clear the title. 2. Press the [D] button and display the sub. 3. Press the [T] button. The display switches to the title input display. 4. Press the [BND] button. 5. Press and hold the [ ] button for 1 second or longer to clear the title and cancel title input mode.

Entering titles

Titles up to 8 characters long can be stored in memory and displayed for CD, CD changer and TV stations. The number of titles that can be entered for each mode are as follows. Mode CD mode TV mode CD changer mode CDC655z connected CDC655Tz connected CDC1255z connected Number of titles 50 titles 20 titles Number of titles 60 titles 100 titles 50 titles
Triggered audio mute for cellular telepones
This unit requires special wiring to mute the audio signal automatically when a cellular telephone rings in the car.
This function is not compatible with all cellular telepones Contact your local authorized Clarion dealer for information on proper installation and compatibility.
1. Press the [FNC] button to select the mode you want to enter a title (CD, CD changer or TV). 2. Select and play a CD in the CD changer or tune in to a TV station for which you want to enter the title. 3. Press the [D] button and display the sub. 4. Press the [T] button. 5. Press the [a] or [d] button to move the cursor. 6. Press the [D] button to select a character. Each time you press the [D] button, the character changes in the following order: Numbers Symbols Capital letters Numbers. 7. Turn the [ROTARY] knob to select the desired character. 8. Repeat steps 5 to 7 to enter up to 8 characters for the title. 9. Press and hold the [ ] button for 2 seconds or longer to store the title into memory and cancel title input mode.
8. OPERATIONS OF ACCESSORIES

CD/MD Changer Operations

CD/MD changer functions
When an optional CD/MD changer is connected through the CeNET cable, this unit controls all CD/MD changer functions. This unit can control a total of 2 changers. Press the [FNC] button and select the CD(MD) changer mode to start play. If 2 CD(MD) changers are connected, press the [FNC] button to select the CD(MD) changer for play.

If NO MAG appears in the display, insert the magazine into the CD changer. DISC CHK appears in the display while the player loads (checks) the magazine. If NO DISC appears in the display, eject the magazine and insert discs into each slot. Then, reinsert the magazine back into the CD changer. If NO DISC appears in the display, load MDs into the MD changer. Note: Some CDs recorded in CD-R/CD-RW mode may not be usable.
Notes: If the CD playing is not a CD-text CD or no user title has been input, NO TITLE appears in the display. If a CD-text CD is not input its disc title or a track title, NO TITLE appears in the display.
Switching disc titles and track titles (MD)
This unit can display disc titles and track titles already entered on MDs.
Titles cannot be entered for MDs with this unit.
1. Press [D] button to display the title. The disc title or track title is displayed. 2. Each time you press and hold the [D] button for 1 second or longer, the display toggles between the disc title and the track title. Note: If an MD is not input its disc title or a track title, NO TITLE appears in the display.
CD-ROM discs cannot be played from every CD changer, its depended on the model.
Procedure to scroll a title
Set SCROLL to ON or OFF. (The factory default setting is ON. Refer to the subsection Turning the screen saver function on or off in section Operation common to each mode.) GWhen set to ON The title is automatically kept scrolling. GWhen set to OFF Press the [T] button to scroll the title.
1. Press the [ ] button to pause play. PAUSE appears in the display. 2. To resume play, press the [ ] button again.
This unit can display title data for CD-text CDs and user titles input with this unit.
Title data for CD-text CDs can be displayed with this unit only when it is connected to CDC655Tz.

Selecting a CD

[DN] or [UP] button correspond to a disc load in the magazine. Press the [DN] or [UP] button to select the desired disc.
If a CD is not loaded in a slot of magazine, NO DISC appears in the display.
GWhen connected to CDC655z or CDC1255z. Press the [D] button to display the title. GWhen connected to CDC655Tz 1. Press the [D] button to display the title. 2. Each time you press and hold the [D] button for 1 second or longer, the title display changes in the following order: User title (disc) CD-tect title (disc) Artist title CD-text title (track) User title (disc)

Selecting a MD

[DN] or [UP] button correspond to a MD load in the MD changer. Press the [DN] or [UP] button to select the desired disc.
If a MD is not loaded in a slot of MD changer, NO DISC appears in the display.
2. To cancel disc scan play, press the [SCN] button again. DISC and SCN go off from the display and the current track continues to play.
Repeat play continuously plays the current track. This function continues automatically until it is cancelled. 1. Press the [RPT] button. RPT lights in the display and the current track is repeated. 2. To cancel repeat play, press the [RPT] button again. RPT goes off from the display and normal play resumes.

Disc repeat play

After all the tracks on the current disc have been played, disc repeat play automatically replays the current disc over from the first track. This function continues automatically until it is cancelled. 1. Press and hold the [RPT] button for 1 second or longer. DISC and RPT light in the display and disc repeat play starts. 2. To cancel disc repeat play, press and hold the [RPT] button again. DISC and RPT go off from the display and normal play resumes on the current track.
Scan play locates and plays the first 10 seconds of each track on a disc automatically. This function continues on the disc until it is cancelled.
Random play selects and plays individual tracks on the disc in no particular order. This function continues automatically until it is cancelled. 1. Press the [RDM] button. RDM lights in the display and random play begins. 2. To cancel random play, press the [RDM] button again. RDM goes off from the display and normal play resumes.
1. Press the [SCN] button to start track scanning. SCN lights in the display. 2. To cancel the scan play, press the [SCN] button again. SCN goes off from the display and the current track continues to play.

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular order. This function continues automatically until it is cancelled. 1. Press and hold the [RDM] button for 1 second or longer. DISC and RDM light in the display and disc random play starts. 2. To cancel disc random play, press and hold the [RDM] button again. DISC and RDM go off from the display and normal play resumes from the current track.

Disc scan play

1. Select the desired station with seek tuning, manual tuning or preset tuning. 2. Press and hold one of [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory.
2. Press the [a] or [d] button to automatically seek a station. Press the [d] button to automatically tune up the frequency band to the next available TV station; press the [a] button to automatically tune down.
Auto store selects 6 TV stations automatically and stores each one into preset memory. If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory. 1. Press the [BND] button and select the desired TV band (TV1 or TV2). 2. Press and hold the [P/A] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.

Setting the TV diver

You can change the reception setting for the TV antenna connected to the TV tuner. 1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select TV DIVER. 3. Turn the [ROTARY] knob clockwise to set to ON or counterclockwise to set to OFF. G ON: Sets reception emphasizing the visual. G OFF: Sets the diver setting to OFF. 4. Press the [T] button to return to the previous mode.
Preset scan allows the user to view each preset position before it automatically advances to the next preset. This function is useful for searching for a desired TV station in memory. 1. Press the [P/A] button. 2. When the desired station is found, press the [P/A] button again to remain tuned to that station. Note: Do not press and hold the [P/A] button for 2 seconds or longer. Doing so will trigger the auto store function and start storing stations into memory.

Setting the TV area

When you select the TV area (TV reception area), the TV tuner area setting changes. 1. Press and hold the [T] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [a] or [d] button to select TV AREA. 3. Press the [ ] button. 4. Turn the [ROTARY] knob clockwise or counterclockwise to select the reception area. 5. Press the [ ] button. 6. Press the [T] button to return to the previous mode.

9. IN CASE OF DIFFICULTY

Problem Power does not turn on. (No sound is produced.) Cause Fuse is blown. Measure Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Consult your store of purchase.
Incorrect wiring. No sound output when operating the unit with amplifiers or power antenna attached.
Power antenna lead is shor- 1. Turn the unit off. ted to ground or excessive 2. Remove all wires attached to the power current is required for reantenna lead. Check each wire for a possible mote-on the amplifiers or short to ground using an ohm meter. power antenna. 3. Turn the unit back on. 4. Reconnect each amplifier remote wire to the power antenna lead one by one. If the amplifiers turn off before all wires are attached, use an external relay to provide remote-on voltage (excessive current required). The microprocessor has malfunctioned due to noise, etc. Turn off the power, then press the [OPEN] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod.

General

Nothing happens when buttons are pressed. Display is not accurate.

Reset button

DCP or main unit connectors are dirty. Compact disc cannot be loaded. Sound skips or is noisy. Another compact disc is already loaded. Compact disc is dirty. Compact disc is heavily scratched or warped. Sound is bad directly after power is turned on.
Wipe the dirt off with a soft cloth moistened with cleaning alcohol. Eject the compact disc before loading the new one. Clean the compact disc with a soft cloth. Replace with a compact disc with no scratches.
Water droplets may form on Let dry for about 1 hour with the power on. the internal lens when the car is parked in a humid place.

10. ERROR DISPLAYS

If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. Error Display ERROR 2 Cause A CD is caught inside the CD deck and is not ejected. Measure This is a failure of CD decks mechanism and consult your store of purchase.

CD changer

MD changer

ERROR 3 ERROR 6

A CD cannot be played due to scratches, etc. A CD is loaded upside-down inside the CD deck and does not play. A CD inside the CD changer is not loaded.
Replace with a non-scratched, non-warped-disc. Eject the disc then reload it properly.

ERROR 2

This is a failure of CD changers mechanism and consult your store of purchase.

ERROR 3

A CD inside the CD changer cannot be played due to scratches, etc. A CD inside the CD changer cannot be played because it is loaded upside-down. Displayed when the temperature in the MD changer is too high and playback has been stopped automatically. An MD inside the MD changer is not loaded.
Replace with a non-scratched, nonwarped disc. Eject the disc then reload it properly.

ERROR 6

ERROR H
Lower the surrounding temperature and wait for a while to cool off MD changer.
This is a failure of MD changers mechanism and consult your store of purchase.
An MD inside the MD changer cannot be played due to scratches, etc.
Replace with a non-scratched, nonwarped disc.
An MD inside the MD changer cannot be played because it is loaded upside-down. Displayed when a non-recorded MD is loaded in the MD changer.
Eject the disc then reload it properly.
Load a pre-recorded MD in the MD changer.

Error Display ERROR 2

Cause A DISC inside the DVD changer cannot be played. A DISC cannot be played due to scratches, etc. A DISC inside the DVD changer cannot be played because it is loaded upside-down. Parental level error Region code error

Measure

This is a failure of DVD mechanism and consult your store of purchase. Retry or replace with a non-scratched, nonwarped-disc. Eject the disc then reload it properly