Printed in China / Imprim en Chine / Impreso en China

2004/12

284-0157-00
Installation/Wire Connection Guide Manuel dinstallation et de connexion Gua de instalacin/conexin de cables

English Franais Espaol

I PRECAUTION
Remove the stopper following the procedures below when this source unit is installed without the universal mounting bracket. 1. Remove the screw from the source unit (Figure 5). 2. Remove the stopper from the source unit (Figure 6). 3. Install the remove screw to the source unit (Figure 7). Securely attach the screw. Note: Store the removed stopper in a safe place together with the Instruction Manual.
Retire el tapn despus de los siguientes procedimientos indicados abajo cuando esta unidad de la fuente est instalada sin el soporte de montaje universal. 1. Quite el tornillo de la unidad de la fuente (Figura 5). 2. Quite el tapn de la unidad de la fuente (Figura 6). 3. Instale el tornillo retirado de la unidad de la fuente (Figura 7). Apriete firmemente el tornillo. Nota: Guarde el tapn retirado en un lugar seguro junto con el Manual de Instrucciones.

I PRECAUCION

I `Prcaution
Retirer la languette en procdant comme suit pour installer le module source sans la patte de montage universel. 1. Retier la vis du module source (Figure 5). 2. Retirer la languette du module source (Figure 6). 3. Fixer la vis ainsi retire sur le module source (Figure 7). Fixer la vis fond. Remarque: Ranger la languette retire en lieu sr avec le mode demploi.
1. BEFORE STARTING / PRPARATIFS / ANTES DE COMENZAR
1. This set is exclusively for use in cars with a negative ground, 12 V power supply. 2. Read these instructions carefully. 3. Be sure to disconnect the battery - terminal before starting. This is to prevent short circuits during installation. (Figure 1) 1. Cet appareil est exclusivement destin tre utilis dans les voitures avec une alimentation 12 V masse ngative. 2. Lire ces instructions attentivement. 3. Sassurer de dbrancher la borne - de la batterie avant de commencer. Cela vitera les court-circuits pendant linstallation. (Figure 1) 1. Esta unidad ha sido diseada para utilizarse exclusivamente en automviles con fuente de alimentacin de 12 V, y negativo a masa. 2. Lea cuidadosamente estas instrucciones. 3. Antes de comenzar, cercirese de desconectar el terminal - de la batera. Esto es para evitar cortocircuitos durante la instalacin. (Figura 1)
Figure 1 / Figure 1 / Figura 1
Car battery Batterie de voiture Batera del automvil
Example 1/Exemple 1/Ejemplo 1
1 Stopper/Languette/Tapn 2 Source Unit/Module source/Unidad de la fuente 3 Screwdriver/Toumevis/Destornillador 4 Screw/Vis/Tornillo
Example 2/Exemple 2/Ejemplo 2
IPRECAUTION Push in the protruding part as shown in the figure. IPRECAUCION Empuje la parte saliente como se muestra en la figura. IPRCAUTION Appuyez sur la pice faisant saillie comme indiqu sur la figure. 1 Stopper/Languette/Tapn 2 Source Unit/Module source/Unidad de la fuente

English

Franais

Espaol

Figure 5 / Figure 5 / Figura 5 Figure 6 / Figure 6 / Figura 6 Figure 7 / Figure 7 / Figura 7
2. CAUTIONS ON INSTALLATION / PRCAUTIONS AU SUJET DE LINSTALLATION / PRECAUCIONES PARA LA INSTALACIN
1. Prepare all articles necessary for installing the source unit before starting. 2. Install the unit within 30 of the horizontal plane. (Figure 2) 3. If you have to do any work on the car body, such as drilling holes, consult your car dealer beforehand. 4. Use the enclosed screws for installation. Using other screws can cause damage. (Figure 3) 1. Avant de commencer, prparer toutes les pices ncessaires pour installer lappareil pilote. 2. Installer lappareil avec un angle infrieur 30 par rapport lhorizontal. (Figure 2) 3. Sil est ncessaire deffectuer certains travaux sur la carrosserie comme percer des trous, consulter dabord votre concessionnaire automobile. 4. Utiliser les vis fournies pour linstallation. Lutilisation dautres vis peut causer des dommages. (Figure 3) 1. Antes de comenzar, prepare todos los elementos necesarios para instalar la unidad fuente. 2. Instale la unidad con un ngulo de 30 sobre el plano horizontal. (Figura 2) 3. Si tiene que realizar cualquier trabajo en la carrocera, como taladrado de orificios, etc., consulte al proveedor de su automvil. 4. Use los tornillos incluidos para la instalacin. El uso de otros tornillos puede causar daos. (Figura 3)
Figure 8 / Figure 8 / Figura 8
Figure 9 / Figure 9 / Figura 9
Figure 10 / Figure 10 / Figura 10
I Fixed Mount (Using the bracket originally equipped in vehicle) This unit is designed for fixed installation in the dashboard. If the vehicle is equipped with a factory-installed radio, install the source unit with the parts and screws marked (#). (Figure 11) If the vehicle is not equipped with a factory-installed radio, obtain an installation kit to install the source unit in the following procedure. 1. Secure the mounting brackets to the chassis as shown in Figure 11. When the source unit is installed without the universal mounting bracket, holes exist; modification, such as drilling new holes, of the mounting brackets may be required for other models. 2. Wire as shown in Installation (Section 6).

Source indication

1. When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour. The condensation will disappear naturally allowing normal operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

CAUTION

BE CAREFUL NOT TO GET YOUR FINGERS CAUGHT WHEN OPENING AND CLOSING THE SLOPING CONSOLE. 1. For safetys sake, always close the SLOPING CONSOLE before leaving this unit unused for a prolonged period or switching OFF the ignition key. If you switch OFF the ignition key with the SLOPING CONSOLE tilted, the SLOPING CONSOLE does not close.
USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THE COMPACT DISC PLAYER and MINI DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.
Spectrum analyzer display, Function indication Source icon You can select from 5 display patterns in the SPE/ANA PTN setting. Sub icon : Trick play indication

Level bar display

Sub display

Handling Compact Discs

Use only compact discs bearing the mark. or Do not play heart-shaped, octagonal, or other specially shaped compact discs. Some CDs recorded in CD-R/CD-RW mode may not be usable. Do not use compact discs that have large scratches, are misshapen, cracked, etc. Use of such discs may cause misoperation or damage. To remove a compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may damage the disc or cause breakdown of the internal mechanism.

Title display

Spectrum analyzer display You can select from 4 display patterns in the SPE/ANA PTN setting.
INFORMATION FOR USERS:. CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

Handling

Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played. Therefore, do not leave them for a long time in the car. New discs may have some roughness around Ball-point pen the edges. If such discs Roughness are used, the player may not work or the sound may skip. Use a ballpoint pen or the like to remove any roughness from the edge of the disc. Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player.

Storage

Do not expose compact discs to direct sunlight or any heat source. Do not expose compact discs to excess humidity or dust. Do not expose compact discs to direct heat from heaters.

Cleaning

To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference. Do not use any solvents, such as commercially available cleaners, anti-static spray, or thinner to clean compact discs. After using special compact disc cleaner, let the compact disc dry off well before playing it.
You cannot change the combination of the upper and lower title to your preference. The user title is displayed only in the upper title, and the lower title does not appear. The title display does not appear in the radio, TV, AUX or DVD changer mode.
Operation status indication, Title indication
Bottom View of Source Unit

LCD Screen

In extreme cold, the screen movement may slow down and the screen may darken, but this is normal. The screen will recover when it returns to normal temperature.
Be sure to unfold and read the next page. / Veuillez dplier et vous rfrer la page suivante. Cercirese de desplegar y de leer la pgina siguiente.

Selects one of the 4 types of sound characteristics preset in memory.

[A-M] button

Switches to the audio mode (SUB-WOOF VOL, ADF, BASS, TREBLE, BALANCE, FADER). Press and hold for 1 second or longer to turn on or off the MAGNA BASS EXTEND.

[REC] button

Press during CD playback, and the track currently being played back is recorded onto MC. (TRACK REC) Press and hold for 2 seconds or longer during CD playback, and all tracks are recorded onto MC. (DISC REC)

When the TV is connected

For details, see the section TV Operations.

[ADJ] button

Switches to the adjust mode.
Performs preset scan. Press and hold for 2 seconds or longer to perform auto store.

[COLOR] button

Press to select display color.
Selects a station while in the radio mode or selects a track when listening to the CD/MP3/WMA, MC mode. This lever is used to make various settings. Move for 1 second or longer to switch the fast-forward/fast-rewind.
Switches the band. Press and hold for 1 second or longer to switch seek or manual tuning.
Switches the band. Press and hold for 1 second or longer to switch seek or manual tuning. Returns to a first track while in the CD/MP3/WMA, MC mode. Press and hold for 1 second or longer to switch the track type to play in the CD/MP3/WMA mode.
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas.

[ROTARY] knob

Turn to adjust the volume. Performs various settings.
Press and hold for 1 second or longer to switch the TV picture mode or VTR (external) picture mode.

CD insertion slot.

5. DCP
The control panel can be detached to deter theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car.

Attaching the DCP

1. Insert the DCP so that the A section on the right side of the DCP catches on the hook B on the unit.

Removing the DCP

1. With the SLOPING CONSOLE closed, turn off the power. 2. Press the [RELEASE] button deeply to open the DCP.
2. Press the left side C of the DCP carefully to fit it in place.
3. Pull the DCP toward you and remove it.
The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. If the [RELEASE] button is pressed and the DCP is not locked into place, it may fall out from vibration of the car. This can break the DCP, so after removing it, either install it on the unit or put it in its DCP case. The connector connecting the unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc.

Note: If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.
Always close the SLOPING CONSOLE before removing the DCP. If you remove the DCP with the SLOPING CONSOLE open, the sloping console closes immediately. Be careful not to get your fingers caught.

6. REMOTE CONTROL

Receiver for remote control unit
Operating range: 30 in all directions Signal transmitter

Remote control unit

[SRC] [BND] [ [ ], [ ] [a], [d] [MUTE] [ISR] [SCN] [DISP] [RDM] [RPT] ]

Inserting the Battery

1 Turn over the remote control unit and slide the cover in the direction indicated by the arrow in the illustration. 2 Insert the battery (CR2025) into the insertion guides, with the printed side (+) facing upwards. 3 Press the battery in the direction indicated by the arrow so that it slides into the compartment. 4 Replace the cover and slide in until it clicks into place.
Notes: Misuse may result in rupture of the battery, producing leakage of fluid and resulting in personal injury or damage to surrounding materials. Always follow these safety precautions:
Use only the designated battery. When replacing the battery, insert properly, with +/polarities oriented correctly. Do not subject battery to heat, or dispose of in fire or water. Do not attempt to disassemble the battery. Dispose of used batteries properly.

Insertion guide

Functions of the Remote Control Unit Buttons

Mode Button

[SRC] [BND]

Radio/SIRIUS

CD/MP3/WMA/ M.CATCHER

CD changer DVD changer

Switches among radio, SIRIUS tuner, CD/MP3/WMA, MC, CD changer, DVD changer, TV and AUX. Switches reception band. Returns to the first track. Moves the next disc in increasing order. Switches reception band.

],[ ],[

Increases and decreases volume (in all modes). Moves preset channels up and down. No function. Turns mute on and off. Recalls ISR radio station in memory. When pressed and held for 2 seconds or longer: Stores current station into ISR memory (radio mode only). Switches among main display, sub display and title display. When pressed and held for 1 second or longer: Switches the titles (except in the radio, DVD changer, TV mode). Preset scan. When pressed and held for 2 seconds or longer: Auto store. Scan play. When pressed and held for 1 second or longer: Folder scan play (MP3/WMA disc, MC mode). Repeat play. When pressed and held for 1 second or longer: Folder repeat play (MP3/WMA disc, MC mode). Random play. When pressed and held for 1 second or longer: Folder random play (MP3/WMA disc, MC mode). Scan play. When pressed and held for 1 second or longer: Disc scan play. Preset scan. When pressed and held for 2 seconds or longer: Auto store. Moves tracks up and down. When pressed and held for 1 second or longer: Fast-forward/fast-rewind. Switches between playback and pause. Moves preset channels up and down. No function.

The factory default setting is OFF.

Selecting a mode

1. Press the [SRC] button to change the operation mode. 2. Each time you press the [SRC] button, the operation mode changes in the following order: Radio mode SIRIUS mode CD/MP3/ WMA mode M.CATCHER mode CD changer mode DVD changer mode TV mode AUX mode Radio mode.
External equipment not connected through CeNET will not be displayed.
1. Press and hold the [A-M] button for 1 second or longer to turn on the MAGNA BASS EXTEND effect. M-BASS EX ON appears on the display. 2. Press and hold the [A-M] button for 1 second or longer to turn off the MAGNA BASS EXTEND effect. M-BASS EX OFF appears on the display.
Note: When ADF 1, ADF 2, ADF 3 or ADF USER is selected for ADF (Anti Distortion Filter), setting of MAGNA BASS EX cannot be performed.

Adjusting the subwoofer

The factory default setting is 0 This function can be adjusted only when the subwoofer output is set to ON. For details on how to set the subwoofer, refer to the subsection Setting the subwoofer in the section Common Operations.
Setting the Anti Distortion Filter
The adopted Liveliness Enhancement Filter and Sound Tone Compensation functions allow wellmodulated realistic playback without affecting the characteristics of the original sound tone. This unit is provided with 4 types of sound tone effects stored in memory. Select the one you prefer.
The factory default setting is ADF OFF.
Each time you press the [ADF] button, the tone effect changes in the following order: ADF 1 ADF 2 ADF 3 ADF USER ADF OFF ADF 1. ADF 1 : suitable for the genuine speakers ADF 2 : suitable for separate speakers ADF 3 : suitable for coaxial speakers ADF USER: this setting can be adjusted by the user to his or her individual preference. ADF OFF : no sound effect Notes: The volume changes each time the ADF (Anti Distortion Filter) setting is switched. Turn down the volume and the sub-woofer volume before performing a switching operation. Sufficient effects cannot be obtained with some speaker systems. In such cases, adjust the volume.
1. Press the [A-M] button to select SUBWOOF VOL. 2. Turn the [ROTARY] knob to select from 6 to +6. 3. When the adjustment is complete, press the [A-M] button several times until the function mode is reached.

Adjusting the fader

1. Press the [A-M] button and select FADER. 2. Turn the [ROTARY] knob to adjust the balance of the front and rear speakers.
The factory default setting is 0. (Adjustment range: F12 to R12)
2. Tune into a station. Quick tuning: Move the [a]/[d] lever for 1 second or longer to tune in a station. Step tuning: Move the [a]/[d] lever to manually tune in a station.

Preset scan

Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory. 1. Press the [PS/AS] button. 2. When a desired station is tuned in, press the [PS/AS] button again to continue receiving that station. Note: Be careful not to press and hold the [PS/AS] button for 2 seconds or longer, otherwise the auto store function is engaged and the unit starts storing stations.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6FM3, 6-AM) exists to store individual radio stations in memory. Pressing the corresponding [DIRECT] button recalls the stored radio frequency automatically. 1. Press the [BND] button and select the desired band (FM or AM). 2. Press the corresponding [DIRECT] button to recall the stored station.
Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store that station into preset memory.
Instant station recall (ISR)
Instant station recall is a special radio preset that instantly accesses a favorite radio station at a touch of a button. The ISR function even operates with the unit in other modes. ISR memory 1. Select the station that you wish to store in ISR memory. 2. Press and hold the [ISR] button for 2 seconds or longer. Recalling a station with ISR In any mode, press the [ISR] button to turn on the radio function and tune the selected radio station. ISR appears in the display. Press the [ISR] button again to return to the previous mode.

Manual memory

1. Select the desired station with seek tuning, manual tuning or preset tuning. 2. Press and hold one of the [DIRECT] buttons for 2 seconds or longer to store the current station into preset memory.

Auto store

Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. If 6 receivable stations cannot be received, a previously stored station remains unoverwritten at the memory position. 1. Press the [BND] button and select the desired band (FM or AM). 2. Press and hold the [PS/AS] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.

CD/MP3/WMA Operations

MP3/WMA

What is MP3?

MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This audio compression method has penetrated into PC users and become a standard format. This MP3 features the original audio data compression to about 10 percent of its initial size with a high sound quality. This means about 10 music CDs can be recorded on a CD-R disc or CD-RW disc to allow a long listening time without having to change CDs.

Mixed with CD and Play CD Play MP3/WMA MP3/WMA type tracks CD type track only Play CD Play CD MP3/WMA type track only Play MP3/WMA Play MP3/WMA 2. After making these settings, remove the disc and then reinsert it.
3. When a mixed mode CD is loaded and CD is set, the track to be played first is MP3/WMA file data and no sound is heard. Note: When playing a CCCD (Copy Control CD), set the setting to CD type. When this is set to MP3/WWA type, the CD cannot be played normally in some cases.
Be careful not to catch your hand or fingers while closing the SLOPING CONSOLE. Do not try to put your hand or fingers in the disc insertion slot. Also never insert foreign objects into the slot. Do not insert discs where adhesive comes out from cellophane tape or a rental CD label, or discs with marks where cellophane tape or rental CD labels were removed. It may be impossible to extract these discs from the unit and they may cause the unit to break down.

Disc-In-Play function

As long as the ignition key is turned to the ON or ACC position, this function allows you to turn the power to the unit and start playing the disc automatically when the disc is inserted even if the power is not turned on.

Loading a CD

1. Press the [Q] button. The SLOPING CONSOLE opens. 2. Insert a CD into the center of the CD SLOT with the label side facing up. The CD plays automatically after loading. Notes: Never insert foreign objects into the CD SLOT. If the CD does not insert easily, there may be another CD in the mechanism or the unit may require service.
or mark and Discs not bearing the CD-ROMs cannot be played by this unit. Some CDs recorded in CD-R/CD-RW mode may not be usable. Loading 8 cm compact discs No adapter is required to play an 8 cm CD. Insert the 8 cm CD into the center of the insertion slot.
Listening to a disc already loaded in the unit
Press the [SRC] button to select the CD/MP3/ WMA mode. When the unit enters the CD/MP3/WMA mode, play starts automatically. If there is no disc loaded, the indication NO DISC appears in the display.

Play list mode

This function allows you to play tracks, up to latest 5 time stamps, by reading the play list information written on the disc. 1. Press and hold the [P.LIST] button for 1 second or longer to turn on or off the play list mode.
Play list play is possible only when there is a file whose extension is.M3U on the CD-R/ RW. Up to 5 play lists can be recognized, and up to 255 files can be recognized per play list.
2. Press the [DN] button to move to the previous play list. Press the [UP] button to move to the next play list. Notes: The SCN/RPT/RDM functions cannot be used while in the play list mode. The title changes from folder name to play list name.

Making a play list

1. Write desired tracks to a CD-R/RW, etc. Be sure to use alphanumeric/ASCII characters for all file names. 2. Make a play list by using a multimedia player, etc. and save the data. The file format must be M3U. 3. Again, write this play list to the CD-R/RW, etc.

MUSIC CATCHER Operations

Setting a recording mode
MUSIC CATCHER can be switched between 2 recording modes: HQ (High Quality) MODE: about 265 minutes LP (Long Play) MODE: about 353 minutes
The factory default setting is HQ.
Recording operation (REC function)
Recording using MUSIC CATCHER is performed in the CD/MP3/WMA mode and the following 2 recording modes are available: TRACK REC to record only one track currently being played back and DISC REC to record all tracks on the CD. TRACK REC 1. Press the [SRC] button to select the CD/ MP3/WMA mode. 2. Play back a track to be recorded, and press the [REC] button to start recording. TRACK REC appears on the display for 2 seconds then the REC indicator lights on the display.
When recording is complete, the REC indicator goes off and REC DONE appears on the display for 2 seconds.
1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select MC-REC MODE. 3. Turn the [ROTARY] knob to select HQ or LP. 4. Press the [ADJ] button to return to the previous mode.
Notes on recording using MUSIC CATCHER:
Recording operations are to be performed in the CD/MP3/WMA mode. Recordable media are CD-DAs only. Discs (CD-R/CD-RW) created by copying on a music recorder cannot be recorded. MP3/WMA discs cannot be recorded. Some CDs may show a subtractive time indication in the area between tracks when they are played back. A between-tracks area is not recorded in such a CD. In recording using MUSIC CATCHER, some amount of silent time is created between the tracks. If the disc contains some tracks that have been already recorded, the other tracks are recorded. Folder and track names are added automatically during recording. If the disc is not recordable, NO REC DISC appears on the display. If the disc contains some tracks previously recorded, INCLUDED appears on the display. If there is no empty folder available, FOLDER FULL appears on the display. When the memory capacity is used up, MEMORY FULL appears on the display and recording is canceled. Recording cannot be performed during SCN, RPT, and RDM. In such cases, BUSY appears on the display. The [ ], [BND], and [SCN/RPT/RDM] buttons and the [a]/[d] lever are invalid during recording. When these buttons are pressed, INVALID appears on the display.

1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select SUB-W. 3. Turn the [ROTARY] knob to select ON or OFF. 4. Press the [ADJ] button to return to the previous mode.
Setting the low pass filter
The factory default setting is THROUGH.
Adjusting the display contrast
You can adjust the display contrast to match the angle of installation of the unit.
The factory default setting is 8. (Adjustment level: 1 to 16)
1. Press and hold the [DISP] button for 1 second or longer to switch to the display adjust mode. 2. Move the [a]/[d] lever to select CONTRAST. 3. Turn the [ROTARY] knob to adjust the contrast. 4. Press the [DISP] button to return to the previous mode.
1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select SUB-W LPF. 3. Turn the [ROTARY] knob to select the setting. Each time you turn the [ROTARY] knob, the setting changes in the following order: THROUGH 50Hz 80Hz 120Hz 4. Press the [ADJ] button to return to the previous mode.
Setting the amplifier bypass circuit

Adjust Mode

Anti-theft indicator
The red Anti-theft indicator is a function for detering theft. When the DCP is removed from the unit, this indicator blinks.
1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select BLINK LED. 3. Turn the [ROTARY] knob to select ON or OFF. 4. Press the [ADJ] button to return to the previous mode.
1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select AMP CANCEL. 3. Turn the [ROTARY] knob to select ON or OFF. ON: Uses with connected AMP. OFF: Uses with inside AMP. 4. Press the [ADJ] button to return to the previous mode.
Displaying the Sirius ID No.
This function only applies when a Sirius receiver is connected. The factory default setting is the upper 6 digits.

Other operations

Setting the button illumination

In the title display, select FOLDER in the upper title.
1. Press the [SRC] button to select the mode you want to enter a title (Radio, CD, M.CATCHER, CD changer or TV). 2. Play a track or tune in to a radio/TV station for which you want to enter the title. 3. Do one of the following: In the CD or CD changer mode Press the [TITLE] button to select USER. In the M.CATCHER mode Press the [TITLE] button to select FOLDER.
In the radio or TV mode Skip this step. 3. Press and hold the [TITLE] button for 1 second or longer to switch to the title input display. 4. Press and hold the [BND] button for 1 second or longer to delete the title. 5. Press and hold the [ ] button for 2 seconds or longer to store the setting and return to the previous mode.

Cellular telephone mute

This unit requires special wiring to mute the audio signal automatically when a cellular telephone rings in the car.
This function is not compatible with all cellular telephones. Contact your local authorized Clarion dealer for information on proper installation and compatibility.

7. 8. 9.

In the radio or TV mode Skip this step. Press and hold the [TITLE] button for 1 second or longer to switch to the title input display. Move the [a]/[d] lever to move the cursor. Press the [BND] button to select a character. Each time you press the [BND] button, the character changes in the following order: Capital letters Small letters Numbers and Symbols Umlaut Capital letters Turn the [ROTARY] knob to select the desired character. Repeat steps 5 to 7 to enter up to 10 characters for the title. Press and hold the [ ] button for 2 seconds or longer to store the title into memory and return to the previous mode.

AUX function

This system has an external input jack so you can listen to audio from an external device connected to this unit.
8. OPERATIONS OF ACCESSORIES

CD Changer Operations

CD changer functions
When an optional CD changer is connected through the CeNET cable, this unit controls all CD changer functions. This unit can control a total of 2 changers. Press the [SRC] button and select the CD changer mode to start play. If 2 CD changers are connected, press the [SRC] button to select the CD changer for play.
If NO MAGAZINE appears in the display, insert the magazine into the CD changer. DISC CHECK appears in the display while the player loads (checks) the magazine. If NO DISC appears in the display, eject the magazine and insert discs into each slot. Then, reinsert the magazine back into the CD changer. Note: Some CDs recorded in CD-R/CD-RW mode may not be usable.
Procedure to scroll a title
Set SCROLL to ON or OFF. (The factory default setting is ON. Refer to the subsection Setting the method for title scroll in the section Common Operations.) When set to ON The title is automatically kept scrolling. When set to OFF To scroll just 1 time when the title was changed or you press and hold the [TITLE] button for 1 second or longer.

Selecting a CD

Press the [UP] or [DN] button to select the desired disc.
If a CD is not loaded in a slot of magazine, pressing the [UP] or [DN] button can not work.
CD-ROM discs cannot be played from every CD changer, its depended on the model.
Track-up 1. Move the [a]/[d] lever up to move ahead to the beginning of the next track. 2. Each time you move the lever up, the track advances ahead to the beginning of the next track. Track-down 1. Move the [a]/[d] lever down to move back to the beginning of the current track. 2. Move the lever down twice to move to the beginning of the previous track.
1. Press the [ ] button to pause play. PAUSE appears in the display. ] button again. 2. To resume play, press the [
This unit can display title data for CD-text CDs and user titles input with this unit. When connected to CDC655Tz or DCZ625 1. Each time you press the [TITLE] button, the title changes in the following order: User title (disc) CD-text title (disc) Artist name CD-text title (track) User title (disc) Notes: If the CD playing is not a CD-text CD or no user title has been input, NO TITLE appears in the display. If a CD-text CD is not input its disc title or a track title, NO TITLE appears in the display.
Fast-forward Move the [a]/[d] lever up for 1 second or longer. Fast-rewind Move the [a]/[d] lever down for 1 second or longer.
Scan play locates and plays the first 10 seconds of each track on a disc automatically. This function continues on the disc until it is cancelled.
The scan play is useful when you want to select a desired track.

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular order. This function continues automatically until it is cancelled. 1. Press and hold the [RDM] button for 1 second or longer. 2. To cancel disc random play, press the [RDM] button again.
1. Press the [SCN] button. 2. To cancel the scan play, press the [SCN] button again.

Disc scan play

Disc scan play locates and plays the first 10 seconds of the first track on each disc in the currently selected CD changer. This function continues automatically until it is cancelled.
Disc scan play is useful when you want to select a desired CD.
1. Press and hold the [SCN] button for 1 second or longer. 2. To cancel disc scan play, press the [SCN] button again.

2. Move the [a]/[d] lever to automatically seek a station. Move the lever up to automatically tune up the frequency band to the next available TV station; move the lever down to automatically tune down.
Auto store selects 6 TV stations automatically and stores each one into preset memory. If the 6 stations with good reception are available, stations previously stored in memory remain. Only stations with strong reception are stored into memory. 1. Press the [BND] button and select the desired TV band (TV1 or TV2). 2. Press and hold the [PS/AS] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.
Preset scan allows the user to view each preset position before it automatically advances to the next preset. This function is useful for searching for a desired TV station in memory. 1. Press the [PS/AS] button. 2. When the desired station is found, press the [PS/AS] button again to remain tuned to that station. Note: Do not press and hold the [PS/AS] button for 2 seconds or longer. Doing so will trigger the auto store function and start storing stations into memory.

Setting the TV diver

You can change the reception setting for the TV antenna connected to the TV tuner.
The factory default setting depends on the TV.
1. Press the [ADJ] button to switch to the adjust mode. 2. Move the [a]/[d] lever to select TV DIVER. 3. Turn the [ROTARY] knob to select ON or OFF. ON: Sets the diver setting to ON. OFF: Sets the diver setting to OFF. 4. Press the [ADJ] button to return to the previous mode.

9. IN CASE OF DIFFICULTY

Problem Power does not turn on. (No sound is produced.) No audio when operating the unit with amplifiers. Nothing happens when buttons are pressed. Cause Fuse is blown. Incorrect wiring. Measure Replace with a fuse of the same amperage. If the fuse blows again, consult Clarion dealer. Consult Clarion dealer.

General

CD/MP3/WMA
Amplifier turn-on lead is Turn the unit off and check each wire for a possible shorted to ground or short. If the amplifier turn-on lead shorts out, cover it excessive current is required. with insulation such as tape. The microprocessor has malfunctioned due to noise, etc. Turn off the power, then press the [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod.

Reset button