Do not play heart-shaped, octagonal, or other specially shaped compact discs. Some CDs recorded in CD-R/CD-RW mode may not be usable.
When the TV/DAB is connected
For details, see the section TV Operations or Digital Radio/DAB Operations.

Handling

Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played. Therefore, do not leave them for a long time in the car. New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc.

Ball-point pen Roughness

[BND] button
Switch the band. When the button is pressed and held, switch seek tuning or manual mode.

[ADJ] button

Press and hold the button for 1 second or longer to switch to the TV picture mode or VTR (external) picture mode.

[DIRECT] buttons

Store a station into memory or recall it directly.

[TA] button

Use the button to set the TA (Traffic Announcement) standby mode in the DAB mode. (This function is only DAB tuner.)

1. PRECAUTIONS

1. This unit is applicable for on-road 4 wheel vehicle purpose only. Use for tractor, fork truck, bulldozer, off road vehicle, 2 or 3 wheel motor bicycle, marine boat or other special purpose vehicle is not appropriate. 2. When the inside of the car is very cold and the player is used soon after switching on the heater moisture may form on the disc or the optical parts of the player and proper playback may not be possible. If moisture forms on the disc, wipe it off with a soft cloth. If moisture forms on the optical parts of the player, do not use the player for about one hour. The condensation will disappear naturally allowing normal operation. 3. Driving on extremely bumpy roads which cause severe vibration may cause the sound to skip.

] button

Perform preset scan while in the TV mode. When the button is pressed and held, auto store is performed. (This function is only TV tuner.) Perform service scan while in the DAB mode.

Press the button to enter the adjust mode. Press and hold the button for 1 second or longer to switch to the adjustment mode or RDS adjustment mode (in Radio FM/DAB mode).

[C] [Z]

[ROTARY] knob
Turn to adjust the volume. Perform various settings.

[IR RECEIVER]

Receiver for remote control unit (Operating range: 30 in all directions)

Connected to This Unit

When the CD/DVD changer / iPod interface is connected
For details, see the section CD Changer Operations. For the DVD changer, refer to the Owners Manual provided with the DVD changer. For the iPod interface, refer to the Owners Manual provided with the iPod interface. Hereinafter, iPod interface is abbreviated as iPod BB.
[A-M] [T] [TA] [SRC] [SCN] [RPT] [RDM] [DIRECT] [D] [IR RECEIVER] [BND] [DN], [UP]
Switch the band, or seek tuning or manual tuning while in the radio mode. Play a first track while in the CD/MP3/WMA mode. Press the button to change the character. Press and hold the button for 1 second or longer to delete the title. Press and hold for 1 second or longer to switch the track type to play in the CD/MP3/ WMA mode.
Perform preset scan while in the radio mode. When the button is pressed and held, auto store is performed. Play or pause a CD while in the CD/MP3/ WMA mode. Confirms various settings.
Move the next disc in increasing order.

[UP], [DN] buttons

Select the disc.

[RDM] button

Perform random play. Also perform disc random play when the button is pressed and held.

[Q] button

Press to open the SLOPING CONSOLE and insert a CD into the CD SLOT. Press to eject a CD loaded in the unit.
With the SLOPING CONSOLE opened / Ouvrez la CONSOLE RABATTABLE FFNUNG DER SCHRGKONSOLE / Apertura della CONSOLE INCLINATA Met het KANTELEND BEDIENINGSPANEEL geopend / Apertura de la CONSOLA INCLINABLE DEN LUTANDE KONSOLEN ppen / Com a CONSOLA INCLINVEL aberta

[CD SLOT]

This sensor detects the brightness inside your car. When the auto-dimmer function is set to AUTO, the brightness of the display is dimmed according to the brightness detected by this sensor.
Select the folder while in the MP3/WMA mode.

[RPT] button

Perform repeat play. When this button is pressed and held, disc repeat play is performed.
Store a station into memory or recall it directly while in the radio mode.

[SCN] button

Perform scan play for 10 seconds of each track. Disc scan play is performed when the button is pressed and held.
Perform random play while in the CD/MP3/ WMA mode. Press and hold the button for 1 second or longer to perform folder random play while in the MP3/WMA mode.

[C] button

Buttons color change to multicolor. Press and hold the button for 1 second or longer to go into the user color adjustment.
Select a track when listening to a disc. Press the lever upward or downward and hold in position for 1 second or longer to enter the fast-forward or fast-backward mode.

[Z] button

Use the button to select one of the 3 types of sound characteristics already stored in memory.
Perform repeat play while in the CD/MP3/ WMA mode. Press and hold the button for 1 second or longer to perform folder repeat play while in the MP3/WMA mode.

[T] button

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapitel die Frontdiagramme beachten. Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo. Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas. Observera: Vik ut denna sida fr att kunna se figurerna ver bilstereons framsida medan du lser de olika kapitlen. Nota: Certifique-se de abrir esta pgina e consulte os diagramas frontais conforme realiza a leitura de cada captulo.
Use the button to input a title in the CD mode. Use the button to switch the user titles or track titles, while in the CD/MP3/WMA mode. Use the button to scroll the title during the CD-text play, while in the CD/MP3/WMA mode.
Perform scan play for 10 seconds of each track while in the CD/MP3/WMA mode. Press and hold the button for 1 second or longer to perform folder scan play while in the MP3/WMA mode.

2 280-8334-00

+DXZ768RMP-003-8

06.1.11, 21:14

[SRC] button
Press the button to turn on the power. Press and hold the button for 1 second or longer to turn off the power. Switch the operation mode among the radio mode, etc.
Select a station while in the radio mode or select a track while in the CD/MP3/WMA mode. This lever is used to make various settings. Press the lever upward or downward and hold in position for 1 second or longer to enter the fast-forward or fast-backward mode.

[D] button

Switch the display indication (Main display, Title display) Press and hold the button for 1 second or longer (do not over 4 seconds) to enter the display adjust mode. Press and hold the button for 4 seconds or longer to turn off the display while in the usual play.

P.SCAN (PRESET SCN) AS (AUTO STORE) S.SCAN (S-SCAN) SCAN (TRACK SCAN) RPT (TRACK RPT) RDM (TRACK RDM) D.SCAN (DISC SCAN) D.RPT (DISC RPT) D.RDM (DISC RDM) SCAN (CHAPTER SCN) RPT (CHAPTER RPT) T.RPT (TITLE RPT) F.SCAN (FOLDER SCN) F.RPT (FOLDER RPT) F.RDM (FOLDER RDM)
Displays icon corresponding to playback or selection. Operation status indication Source indication Band / disc No. / folder No. indication Preset channel / track No. indication Receiving frequency or channel / play time indication
Items within parentheses ( ) are displayed during operation as the Operation status indication. : Preset scan : Auto store : Service scan : Track scan : Track repeat : Track random : Disc scan : Disc repeat : Disc random : Chapter scan : Chapter repeat : DVD title repeat : Folder scan : Folder repeat : Folder random
Displayed when changing titles

U USER PS PT S A

: Radio / TV user title : CD user title PS NAME : RDS PS name PTY NAME : RDS PTY name S-LABEL : DAB S-LABEL DISC : CD-TEXT disc title ARTIST : CD-TEXT artist title TRACK : CD-TEXT track title FOLDER : MP3 folder name TRACK : MP3 file name ALBUM : MP3 album tag ARTIST : MP3 artist tag TITLE : MP3 title tag

4. DCP

The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car.

Attaching the DCP

1. Insert the DCP so that the A section on the right side of the DCP catches on the hook B on the unit.

Removing the DCP

1. With the SLOPING CONSOLE closed, turn off the power. 2. Press the [RELEASE] button deeply to open the DCP.

[RELEASE] button

2. Press the left side C of the DCP carefully to fit it in place.
3. Pull the DCP toward you and remove it.
The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. If the [RELEASE] button is pressed and the DCP is not locked into place, it may fall out from vibration of the car. This can break the DCP, so after removing it, either install it on the unit or put it in its DCP case. The connector connecting the unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc.

Note: If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.
Always close the SLOPING CONSOLE before removing the DCP. If you remove the DCP with the SLOPING CONSOLE open, the SLOPING CONSOLE closes immediately. Be careful not to get your fingers caught.

5. REMOTE CONTROL

Signal transmitter

[BND] [ ]

[ ], [ ] [ [MUTE] [TA] [PS/AS] ], [ ]

[DISP] [PTY] [AF]

Inserting the Battery
1 Turn over the remote control unit and slide the cover in the direction indicated by the arrow in the illustration. 2 Insert the battery (CR2025) into the insertion guides, with the printed side (+) facing upwards. 3 Press the battery in the direction indicated by the arrow so that it slides into the compartment. 4 Replace the cover and slide in until it clicks into place. Notes: Misuse may result in rupture of the battery, producing leakage of fluid and resulting in personal injury or damage to surrounding materials. Always follow these safety precautions: Use only the designated battery. When replacing the battery, insert properly, with +/ polarities oriented correctly. Do not subject battery to heat, or dispose of in fire or water. Do not attempt to disassemble the battery. Dispose of used batteries properly. Insertion guide
Functions of the Remote Control Unit Buttons

Mode Button

Radio (RDS) /DAB

CD/MP3/WMA

CD changer DVD changer iPod BB
Switches among radio, DAB, iPod BB, CD/MP3/WMA, CD changer, DVD changer, TV and AUX. Press to cancel a traffic announcement broadcast, an emergency broadcast, and a PTY broadcast during a TA, ALARM or PTY interrupt. Switches reception band. Returns to the first track. Moves the next disc in increasing order. Switches reception band.

],[ ],[

Increases and decreases volume (in all modes). Moves tracks up and down. When pressed and held for 1 second or longer: Fast-forward/fast-rewind. Switches between playback and pause. Moves preset channels up and down. No function.
] Moves preset channels up and down. ] No function. Turns mute on and off.

[MUTE] [TA] [DISP]

TA on and off. Press to cancel a traffic announcement broadcast during a TA interrupt. Switches among main display and title display. When pressed and held for 1 second or longer: Switches the titles (except in the DVD changer, TV mode). Preset scan. When pressed and held for 2 seconds or longer: Auto store. Scan play. When pressed and held for 1 second or longer: Folder scan play (MP3/WMA mode). Scan play. When pressed and held for 1 second or longer: Disc scan play. * Cannot operate via iPod BB. Preset scan. When pressed and held for 2 seconds or longer: Auto store.

If auto store is performed in the FM bands, the stations are stored in FM3 even if FM1 or FM2 was chosen for storing stations.

RDS Operations

RDS (Radio Data System)
This unit has a built-in RDS decoder system that supports broadcast stations transmitting RDS data. This system can display the name of the broadcast station being received (PS) and can automatically switch to the broadcast station with the best reception as you move long distances (AF switching). Also, if a traffic announcement or programme type is broadcast from an RDS station, no matter what mode you are in, this broadcast is received. Additionally, if EON information is received, this information enables automatic switching of other preset stations on the same network and interruption of the station being received with traffic information from other stations (TP). This function is not available in some areas. When using the RDS function, always set the radio to FM mode. AF : Alternative Frequency PS : Programme Service Name PTY : Programme Type EON : Enhanced Other Network TP : Traffic Programme
RDS interrupt does not function during AM radio reception. When set receives RDS signal, and can read PS data, PS appears in the display.

Preset scan

Preset scan receives the stations stored in preset memory in order. This function is useful when searching for a desired station in memory. 1. Press the [ ] button. 2. When a desired station is tuned in, press the [ ] button again to continue receiving that station. Note: ] button Be careful not to press and hold the [ for 2 seconds or longer, otherwise the auto store function is engaged and the unit starts storing stations.
This allows switching of the indication during RDS reception. 1. Each time you press the [T] button, the display changes in the following order: PTY NAME PS NAME

AF function

The AF function switches to a different frequency on the same network in order to maintain optimum reception.
The factory default setting is ON.
1. Press and hold the [ADJ] button for 1 second or longer to switch to the RDS adjust mode. 2. Press the [, ] lever upward or downward to select AF. 3. Turn the [ROTARY] knob to select ON or OFF. ON: AF is lit in the display and the AF function turns on.

OFF: AF goes off in the display and the AF function turns off. 4. Press the [ADJ] button to return to the previous mode.
If the reception of the current broadcast station deteriorates, PI SEARCH appears in the display and the radio searches for the same programme on another frequency.
OFF: REG goes off in the display and the REG function turns off. 4. Press the [ADJ] button to return to the previous mode.
Manually tuning a regional station in the same network
1. This function is valid when the AF function is ON and the REG function is OFF. Note: This function can be used when a regional broadcast of the same network is received. 2. Press any one of the [DIRECT] buttons to call out the regional station. 3. If the reception condition of the called out station is bad, press the [DIRECT] button of the same number. The unit receives a local station on the same network.
AF function between RDS and DAB When the same programme is broadcasted by both RDS and DAB, and this function is ON, the unit switches to receive the broadcast with the better reception automatically.
This function only operates when the DAH923 or DAH913 DAB unit, sold separately, is connected. This factory default setting is ON.
1. Press the [ADJ] button to switch to the adjust mode. 2. Press the [, ] lever upward or downward to select LINK ACT. 3. Turn the [ROTARY] knob to select ON or OFF. ON: AF switching between DAB and RDS enabled. OFF: AF switching between DAB and RDS disabled. 4. Press the [ADJ] button to return to the previous mode.
TA (Traffic Announcement)
In the TA standby mode, when a traffic announcement broadcast starts, the traffic announcement broadcast is received as top priority regardless of the function mode so you can listen to it. Traffic programme (TP) automatic tuning is also possible.
This function can only be used when TP is lit in the display. When TP is lit, this means that the RDS broadcast station being received has traffic announcement programmes.
REG (Regional programme) function
When the REG function is ON, the optimum regional station can be received. When this function is OFF, if the regional station area switches as you drive, a regional station for that region is received.

The factory default setting is OFF. Notes: This function is disabled when a national station such as BBC R2 is being received. The REG function ON/OFF setting is valid when the AF function is ON.
1. Press and hold the [ADJ] button for 1 second or longer to switch to the RDS adjust mode. 2. Press the [, ] lever upward or downward to select REG. 3. Turn the [ROTARY] knob to select ON or OFF. ON: REG is lit in the display and the REG function turns on.
Setting the TA standby mode If you press the [TA] button when only TP is lit in the display, TP and TA light in the display and the unit is set into the TA standby mode until a traffic announcement is broadcast. When a traffic announcement broadcast starts, TRA INFO appears in the display. If you press the [TA] button while a traffic announcement broadcast is being received, the traffic announcement broadcast reception is cancelled and the unit goes into the TA standby mode. Cancelling the TA standby mode As TP and TA lit in the display, press the [TA] button. The TA in the display goes off and the TA standby mode is cancelled.
If TP is not lit, pressing the [TA] button searches for a TP station.
Searching for a TP station When TP is not lit, if you press the [TA] button, TA in the display lights and the unit automatically receives a TP station.
Note: If a TP station is not received, the unit continues the search operation. Pressing [TA] button again goes off TA in the display and stops TP station searching.

Selecting PTY

1. Press and hold the [ADJ] button for 1 second or longer to switch to the RDS adjust mode. 2. Press the [, ] lever upward or downward to select PTY SELECT.
You cannot select PTY SELECT during a TA, ALARM or PTY interrupt.
Auto store function for TP stations
You can automatically store up to 6 TP stations into preset memory. If the number of TP can be received less than 6, broadcast stations already stored in memory and left without being overwritten. As TA lit in the display, press and hold the [ ] button for 2 seconds or longer. The TP stations with the good reception sensitivity are stored into preset memory.
Even if you select FM1 or FM2, a TP station is stored into memory for FM3.
3. Press the [ ] button to go to the PTY select mode. 4. Press any one of the [DIRECT] buttons. Alternatively, Turning the [ROTARY] knob to select the desired PTY.

PTY item ENGLISH News Affairs Info Sport Educate Drama Culture Science Varied Pop M Rock M Easy M Light M Classics Other M Weather Finance Children Social Religion Phone In Travel Leisure Jazz Country Nation M Oldies Folk M Document Contents News Todays events Information Sports Education Drama Culture Science Variety Pop music Rock music Easy music Light music Classics Other music Weather Finance For children Social Religion Phone in Travel Leisure Jazz Country Nation music Oldies Folk music Documentaries

Emergency broadcast

If an emergency broadcast is received, all the function mode operations are stopped. Alarm! appears in the display and the emergency broadcast can be heard. Cancelling an emergency broadcast If you press the [TA] button or [SRC] button , emergency broadcast reception is cancelled.
Switching the PTY display language
You can select one of 4 languages (English, Deutsch, Svenska or Franais) for the PTY displayed in the display.
The factory default setting is ENGLISH.
1. Press the [ADJ] button to switch to the adjust mode. 2. Press the [, ] lever upward or downward to select LANGUAGE. 3. Turn the [ROTARY] knob to select the desired language. 4. Press the [ADJ] button to return to the previous mode.
Volume setting of TA, emergency broadcast (ALARM) and PTY
The volume for TA, ALARM and PTY interrupts can be set during TA, ALARM or PTY interrupt.
The factory default setting is 15.
During a TA, ALARM or PTY interrupt, turn the [ROTARY] knob to set the volume to the desired level (0 to 33).
When the TA, ALARM or PTY interrupt ends, the volume returns to the level it had before the interrupt.

CD/MP3/WMA Operations

MP3/WMA

What is MP3?

MP3 is an audio compression method and classified into audio layer 3 of MPEG standards. This audio compression method has penetrated into PC users and become a standard format. This MP3 features the original audio data compression to about 10 percent of its initial size with a high sound quality. This means about 10 music CDs can be recorded on a CD-R disc or CD-RW disc to allow a long listening time without having to change CDs.

Root folder

Repeat play
This function allows you to play the current track repeatedly. 1. Press the [RPT] button to perform repeat play.

Folder repeat play

This function allows you to play a track currently being played in the MP3/WMA folder repeatedly. 1. Press and hold the [RPT] button for 1 second or longer to perform folder repeat play.

Random play

This function allows you to play all tracks recorded on a disc in a random order. 1. Press the [RDM] button to perform random play.

Folder random play

Press the [UP] button while in the final folder to shift to the first folder. Folder without an MP3/WMA file is not selectable.
2. To select a track, press the [, ] lever upward or downward.
This function allows you to play all the tracks of all the folders recorded on an MP3/WMA disc in a random order. 1. Press and hold the [RDM] button for 1 second or longer to perform folder random play.

To cancel play

1. Press the operating button previously selected.
Operations Common to Each Mode
To change display setting
1. Press and hold the [D] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [, ] lever upward or downward to select the item name. BGV POWER MSG SCRN SAVER MSG INPUT AUTO SCRL DIMMER DIMMER IN When
is displayed, press the ] button to advance to the next operation [ step.
Turning the screen saver function on or off
This unit features various screen saver patterns that are exhibited across the display. If the screen savers are not desired, they can be turned off. If the button operation is performed with the screen saver function on, the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display.
The factory default setting is DEMO.

2-1. Select

SCRN SAVER. ] button.

2-2. Press the [

3. Turn the [ROTARY] knob to select the desired setting value. After completing settings, press the [D] button to return to the previous mode.
3-1. Turn the [ROTARY] knob to select the setting. Each time you turn the [ROTARY] knob, the setting changes in the following order: OFF MSG INFO DEMO

When listening to your calls on your car speakers, you can adjust the volume by turning the [ROTARY] knob.
MUTE: The sound from this unit is muted during telephone calls.
Adjusting the auxiliary input sensitivity
Adjust the auxiliary sensitivity when the audio from an external device is difficult to hear even after adjusting the volume.
The factory default setting is MID.
Setting the auto-volume function (CALIBRATE/A-VOL SENS)
You can automatically change the volume to match your car's speed.
The factory default setting is LOW.
2-1. Select AUX SENS. 3-1. Turn the [ROTARY] knob to select from LOW, MID or HIGH.

CALIBRATE. ] button.

2-3. Accelerate to a speed of 50 km. 2-4. When you reach 50 km, press [ ] button. Calibration is executed. When calibration succeeded After 2 seconds or longer, SUCCESSFUL will appear on the display. When calibration failed After 2 seconds or longer, FAILED will appear on the display. Repeat the procedure from step 2-3. 2-5. Next, adjust the sensitivity. Press the [, ] lever upward or downward to select A-VOL SENS. 3-1. Turn the [ROTARY] knob to select the sensitivity.
Setting the car speaker output for the cellular phone
The factory default setting is RIGHT. To output the telephone calls, set the cellular phone interrupt to ON.
2-1. Select TEL SPEAKER. 3-1. Turn the [ROTARY] knob to select RIGHT or LEFT. RIGHT: Telephone calls can be heard on the front right speaker connected to this unit. LEFT: Telephone calls can be heard on the front left speaker connected to this unit.
Each time you turn the [ROTARY] knob, the setting changes in the following order: OFF (no charge in volume) LOW (charge in volume: small) MID-LOW MID MIDHIGH HIGH (charge in volume: large).
Performing a system check
This function verifies the devices hooked up through CeNET. 2-1. Select SYSTEM CHECK. 2-2. Press and hold the [ ] button for 1 second or longer to start the system check. The digital connection configuration is automatically checked. When the system check is complete, the display returns to the previous mode.
COLOR Indigo Blue Surf Blue Silky White Aqua Green Fresh Green Leaf Green Warm Amber Passion Red Vivid Pink Pale Pink Dark Violet Pure Purple USER COLOR 1 USER COLOR 2 USER COLOR 3

Other operations

Setting the button illumination
Press the [C] button to select a color. Each time you press the [C] button, the color changes in the following order: COLOR SCAN Indigo Blue Surf Blue Silky White Aqua Green Fresh Green Leaf Green Warm Amber Passion Red Vivid Pink Pale Pink Dark Violet Pure Purple USER COLOR 1 USER COLOR 2 USER COLOR 3 COLOR SCAN. Setting COLOR SCAN mode Selecting COLOR SCAN, the color automatically changes.

Disc repeat play

After all the tracks on the current disc have been played, disc repeat play automatically replays the current disc over from the first track. This function continues automatically until it is cancelled. 1. Press and hold the [RPT] button for 1 second or longer.

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular order. This function continues automatically until it is cancelled. 1. Press and hold the [RDM] button for 1 second or longer.

TV tuner functions

When an optional TV tuner is connected through the CeNET cable, this unit controls all TV tuner functions. To watch TV it requires a TV tuner and a monitor.

Watching a TV

1. Press the [SRC] button and select the TV mode. 2. Press the [BND] button to select the desired TV band (TV1 or TV2). Each time the button is pressed, the input selection toggles between TV1 and TV2.
A total of 12 TV stations can be stored (6-TV1 and 6-TV2). This allows you to select your favorite TV stations and store them in memory.
3. Press the [, ] lever upward or downward to tune in the desired TV station.

Watching a video

The TV tuner features a VTR input for an external A/V source, such as a DVD player or game station. 1. Press and hold the [ADJ] button for 1 second or longer to select VTR. 2. To return to the TV broadcast, press and hold the [ADJ] button for 1 second or longer.

Setting the TV area

When you select the TV area (TV reception area), the TV tuner area setting changes. 1. Press the [ADJ] button to switch to the adjust mode. 2. Press the [, ] lever upward or downward to select TV AREA. 3. Turn the [ROTARY] knob to select the reception area. 4. Press the [ADJ] button to return to the previous mode.

Setting the TV diver

You can change the reception setting for the TV antenna connected to the TV tuner.
The factory default setting depends on the TV.

One common PTY can be selected for DAB or RDS. Of DAB PTY and RDS PTY, the PTY which is received earlier takes priority over the other. PTY broadcasts are not yet available in all countries. In the INFO standby mode, INFO stations have priority over PTY stations. In the TA standby mode, TP stations have priority over PTY stations. For details on PTY, refer to the section RDS Operation of each owners manual.
During a TA, INFO, ALARM or PTY interrupt, turning the [ROTARY] knob to set the volume to a desired level (0 to 33).
When the TA, INFO, ALARM or PTY interrupt ends, the volume returns to the level it had before the interrupt.

8. IN CASE OF DIFFICULTY

Problem Power does not turn on. (No sound is produced.) No audio when operating the unit with amplifiers. Nothing happens when buttons are pressed. Cause Fuse is blown. Incorrect wiring. Measure Replace with a fuse of the same amperage. If the fuse blows again, consult Clarion dealer. Consult Clarion dealer.

General

Amplifier turn-on lead is Turn the unit off and check each wire for a possible shorted to ground or short. If the amplifier turn-on lead shorts out, cover it excessive current is required. with insulation such as tape. The microprocessor has malfunctioned due to noise, etc. Turn off the power, then press the [RELEASE] button and remove the DCP. Press the reset button for about 2 seconds with a thin rod.

Reset button

Display is not accurate. No audio.
DCP or main unit connectors Wipe the dirt off with a soft cloth moistened with are dirty. cleaning alcohol. The speaker protection circuit is operating. 1. Check the speaker connection. 2. Turn down sound volume. Function can also be restored by turning the power off and on again. 3. If the sound is muted again, consult Clarion dealer. With the sloping console open, press and hold the [Q] button for 3 seconds or longer. The foreign object is forcibly ejected. Write MP3/WMA files onto the disc properly. Use MP3/WMA files encoded properly. Use ISO9660 level 1, 2 or JOLIET or Romeo file system. Clean the disc with a soft cloth. Replace with a disc with no scratches. Use MP3/WMA files encoded properly.

No audio.

There is a disc other than a compact disc or foreign object already in place. MP3/WMA files are absent on the disc. Files are not recognized as an MP3/WMA file. File system is not correct.

Sound skips or is noisy.

Disc is dirty. Disc is heavily scratched or warped.
Sound is cut or MP3/WMA files are not skipped. encoded properly. Noise is generated or noise is mixed with sound. Poor sound quality in extremely cold weather or extreme humidity. Wrong filename Water droplets may form on the internal lens when the car is parked in a humid place. File system is not correct.

[CD SLOT]

CD insertion slot.

[ROTARY] knob

Turn to adjust the volume. Perform various settings.

[IR RECEIVER]

Receiver for remote control unit (Operating range: 30 in all directions)
Major Button Operations When External Equipment is Connected to This Unit
When the CD/DVD changer / iPod interface is connected
For details, see the section CD Changer Operations. For the DVD changer, refer to the Owners Manual provided with the DVD changer. For the iPod interface, refer to the Owners Manual provided with the iPod interface. Hereinafter, iPod interface is abbreviated as iPod BB.
[A-M] [T] [TA] [SRC] [SCN] [RPT] [RDM] [DIRECT] [D] [IR RECEIVER] [BND] [DN], [UP]

] button

[BND] button
Switch the band, or seek tuning or manual tuning while in the radio mode. Play a first track while in the CD/MP3/WMA mode. Press the button to change the character. Press and hold the button for 1 second or longer to delete the title. Press and hold for 1 second or longer to switch the track type to play in the CD/MP3/ WMA mode.
Perform preset scan while in the radio mode. When the button is pressed and held, auto store is performed. Play or pause a CD while in the CD/MP3/ WMA mode. Confirms various settings.
Move the next disc in increasing order.

[UP], [DN] buttons

Select the disc.

[RDM] button

Perform random play. Also perform disc random play when the button is pressed and held.

[Q] button

Press to open the SLOPING CONSOLE and insert a CD into the CD SLOT. Press to eject a CD loaded in the unit.
With the SLOPING CONSOLE opened / Ouvrez la CONSOLE RABATTABLE FFNUNG DER SCHRGKONSOLE / Apertura della CONSOLE INCLINATA Met het KANTELEND BEDIENINGSPANEEL geopend / Apertura de la CONSOLA INCLINABLE DEN LUTANDE KONSOLEN ppen / Com a CONSOLA INCLINVEL aberta
This sensor detects the brightness inside your car. When the auto-dimmer function is set to AUTO, the brightness of the display is dimmed according to the brightness detected by this sensor.
Select the folder while in the MP3/WMA mode.

[RPT] button

Perform repeat play. When this button is pressed and held, disc repeat play is performed.

[DIRECT] buttons

Store a station into memory or recall it directly while in the radio mode.
Play or pause a CD, DVD or iPod BB.

[T] button

Press the button, switches the user titles or track titles, etc. while in the CD changer mode. Use the button to input a title in the CD changer mode. Use the button to scroll the title during CD-text play.

[SCN] button

Perform scan play for 10 seconds of each track. Disc scan play is performed when the button is pressed and held.
Perform random play while in the CD/MP3/ WMA mode. Press and hold the button for 1 second or longer to perform folder random play while in the MP3/WMA mode.

[C] button

Buttons color change to multicolor. Press and hold the button for 1 second or longer to go into the user color adjustment.
Select a track when listening to a disc. Press the lever upward or downward and hold in position for 1 second or longer to enter the fast-forward or fast-backward mode.

[Z] button

Use the button to select one of the 3 types of sound characteristics already stored in memory.
Perform repeat play while in the CD/MP3/ WMA mode. Press and hold the button for 1 second or longer to perform folder repeat play while in the MP3/WMA mode.

[D] button

Switches the display indication (main display, title display).
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Hinweis: Bitte diese Seite ausfalten und beim Lesen der einzelnen Kapitel die Frontdiagramme beachten. Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo. Opmerking: Vouw deze pagina uit en zie tevens de afbeeldingen van het voorpaneel tijdens het doorlezen van de volgende hoofdstukken. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas. Observera: Vik ut denna sida fr att kunna se figurerna ver bilstereons framsida medan du lser de olika kapitlen. Nota: Certifique-se de abrir esta pgina e consulte os diagramas frontais conforme realiza a leitura de cada captulo.