Installation Matching Control 1. Find a suitable location for the On / Off switch Be sure that it is within easy reach of the driver and can be operated safely from the seated position.
Installation Instructions
Frequency Selector Switch

88.7MHz

89.1MHz
NOTE: The On/Off switch requires a flat surface at least 3/4" in diameter for mounting, with 1" rear clearance. The switch is provided with 36" of wire take this into account when selecting a location, or you will have to extend the switch wires. 2. Connect the RCA inputs to the audio source.
On/Off Switch Plug-in Port
To Car Antenna To Car Radio Antenna Input Black Wire Filter/

Fuse Box

3. Connect the male antenna connector to the car radio's FM antenna input, and the female connector to the car antenna. NOTE: Some vehicles may require antenna adapters (sold separately). 4. Connect the Black wire to chassis ground. 5. Connect the Red wire to accessory +12V. NOTE: Connecting to accessory +12V will ensure that the FM modulator turns off when the ignition is turned off. Connecting this wire to +12V Constant may cause battery drain issues, and is not recommended.
10-FM200-00 (Rev. A) 2001 Clarion Corporation of America

On/Off Switch

Red Wire Chassis Ground To Accessory +12V RCA Input from Audio Source
Set-up and Testing 1. Set the Frequency Select switch to either 88.7 or 89.1. If a local radio station uses the first frequency selected, use the other frequency. 2. Switch the On / Off switch to On ( the "I" position). 3. Turn on the car radio and tune to the frequency selected in Step 1. 4. Turn on the audio source connected to the FM Modulator. This audio source should now be heard over the vehicle speakers. 5. Set the level matching control so that the volume level over the speakers is the same as when listening to radio stations. If loud passages sound distorted, lower the Level Matching Control setting.
User Guide and Product Data Sheet
The Clarion FM200 is a two-channel stereo FM modulator with selectable FM frequencies, variable gain, and a remote on/off switch. It allows the addition of auxiliary audio sources to any FM radio (even those lacking auxiliary inputs). It can be used with DVD players, videocassette players, MP3 players, and more. On/Off Switch To use the FM200: 1) Turn the On/Off switch to the On position (This is the position with the "I" icon). 2) Turn on the radio and select the FM band. Tune in either 88.7 or 89.1 (your installer can advise you which frequency setting is being used in your installation). Once you determine the correct frequency, it is a good idea to store the frequency using one of your radio's preset keys. 3) Turn on the auxiliary audio source (VCR, DVD, MP3 player, etc.) and begin playback. The sound from the source unit should now be audible over your speakers. 4) To return to standard radio use, turn the On/Off switch to the Off position (this is the position with the "O" icon). On position

Off position

Specifications: Operating Voltage: 14.4V DC Nom. (Operating Range 10.8 to 15.6V DC) Max. Current Consumption: Operating Frequencies: 200mA 88.7, 89.1 FM
Fuse rating (in Fuse/Filter box): 2A AGC Parts List: (1) FM Modulator Main Unit with integrated harness. (1) On/Off Switch with integrated harness.

10-FM200-00 (Rev. A)

2001 Clarion Corporation of America

Warning!

THE CLARION VMA6593 MONITOR IS ONLY DESIGNED TO BE VIEWED BY REAR-SEAT OCCUPANTS. DIGITAL VIDEO PRODUCTS ARE NOT INTENDED FOR VIEWING BY THE DRIVER WHILE THE VEHICLE IS IN MOTION. SUCH USE MAY DISTRACT THE DRIVER OR INTERFERE WITH THE DRIVERS SAFE OPERATION OF THE VEHICLE, AND THUS RESULT IN SERIOUS INJURY OR DEATH. SUCH USE MAY ALSO VIOLATE STATE LAW. CLARION DISCLAIMS ANY LIABILITY FOR ANY BODILY INJURY, INCLUDING FATALITIES, OR PROPERTY DAMAGE THAT MAY RESULT FROM ANY IMPROPER OR UNINTENDED USES OF THIS PRODUCT.

Table of Contents

1. Introduction... 2 2. Care and Maintenance.. 3 3. Using the VMA6593... 3 4. Installation and Wiring... 6 5. Troubleshooting... 15 6. Specifications... 15 7. Limited Warranty Information.. 16

About Installation

Installation of mobile audio and video components requires experience with a variety of mechanical and electrical procedures. Even though this manual provides general installation and operation instructions for your new Clarion VMA6593 Widescreen Video Monitor, it does not show the exact installation methods for your particular vehicle. If you do not have the required knowledge and experience to successfully complete the installation, we strongly recommend consulting an authorized Clarion dealer about professional installation options.

VMA 6593 122302.p65

12/23/02, 10:34 PM

1. INTRODUCTION

The Clarion VMA6593 is a high-performance video monitor designed specifically for the mobile environment. It is intended for use with other Clarion multimedia products, and can also be integrated with many other products as part of a complete mobile video solution. With two video inputs, the VMA6593 can support simultaneous connection to both dedicated video source units and optional audio/video components such as camcorders or videogames. The infrared remote control receiver output allows integration with select Clarion DVD and VHS source units. The VMA6593 automatically switches to operate with either NTSC or PAL video signals (NTSC is the standard North American video format). The 16:9 aspect ratio screen allows DVD films to be viewed in their original aspect ratio for the best cinematic experience.
Note: The VMA6593 is designed to be a component in a full audio/ video system. If you have any questions about compatible components, such as system controllers, source units, FM modulators, or other audio/video products, please contact your authorized Clarion dealer.
What is included with the VMA6593
The VMA6593 monitor unit The wiring harness A flush-mount trim bezel Owners Manual / Installation Guide

FCC Approval

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

VMA6593

2. CARE AND MAINTENANCE

Liquids and the VMA6593

Keep all liquids, including beverages and cleaning liquids, away from the VMA 6593. Liquids inside the monitor can damage the electronics, and result in electrical shock or fire. If the unit should become wet, turn off all power and contact an authorized Clarion dealer to have the monitor inspected.

3. USING THE VMA 6593

In order to operate the VMA6593, the vehicle ignition key switch must be in the ACC or RUN position.
ACC or engine ON position
WARNING! To prevent the battery from going dead, operate this unit with the engine running, if possible.

Servicing the VMA6593

In the event that trouble arises, never open the case or disassemble the unit. The internal parts are not serviceable by the user. Opening any components will void the warranty.
CAUTION! Changes or modifications to this product not approved by the manufacturer will void the warranty and will violate FCC approval.

Front-Panel Controls

The [SOURCE] button selects between the two video inputs of the VMA6593.
6.5 INCH WIDE LCD MONITOR
Note: If only one of the video inputs is used, the screen will remain dark when the unused input is selected.
The [WIDE] button changes the display mode from wide 16:9 mode to normal 4:3 mode.
IR receiver WIDE PICTURE (+) and (-) adjustment keys

SOURCE

Note: When using a DVD player as the source unit, make sure that the DVD players output mode is set to Wide or 16:9, so that it will generate a video signal that can take advantage of the VMA6593s aspect ratio. When using this display with sources that generate a normal, 4:3 image signal, such as videogames and videocassette players, the [WIDE] button will stretch the image to fit the screen. In this case, some minor image distortion may be visible.
The [POWER] button turns the VMA6593 on and off.
Notes: Even after the VMA6593 is switched on, the screen remains dark until a video signal is detected. When the ignition switch is turned off, the VMA6593 automatically shuts off. The next time the ignition switch is turned on, the VMA6593 will remain off until the [POWER] button is pressed. VMA6593
The [PICTURE] button accesses the display adjustment menus. Each time this button is pressed, the unit will step to the next setting mode, and the screen will display the value of the selected setting. These adjustment settings are: Brightness Contrast Color Tint Mem Reset (resets above to original values) Change the value of each setting by pressing the [+] and [-] buttons. Each setting has 42 steps of adjustment range.
Note: When the MEM RESET option is displayed on the screen, pressing either the [+] or [-] buttons will reset all settings to their original factory values. If you do not wish to reset the settings, either press the [PICTURE] button again, or wait for the monitor to exit the picture adjustment mode automatically.

Note: If the MEM RESET option is used and the VMA6593 is set to Source 2, the monitor will revert to the default setting of Source 1. If there is no active input on Source 1, the screen may go dark. If this happens, press the [SOURCE] button to switch the monitor back to Source 2.
6.5 INCH WIDE LCD MONITOR 6.5 INCH WIDE LCD MONITOR
The IR Receiver detects the signals from infrared remote controls that are included with optional Clarion video source units. Aim remote controls at this IR receiver during use.
Note: The IR Receiver only functions with select Clarion multimedia equipment.

BRIGHTNESS

CONTRAST
PICTURE (+) and (-) adjustment keys
PICTURE (+) and (-) adjustment keys (+) and (-) adjustment keys

PICTURE

MEM RESET

12/23/02, 10:36 PM

6. INSTALLATION AND WIRING

1. Before Starting

Read these instructions and the following precautions carefully. WARNING! Be sure to disconnect the battery (-) terminal before starting. This is to prevent short circuits during installation.
Use a soft, dry cloth to clean the screen. Never use a rough cloth, thinner, benzene, alcohol, or other solvent. The screen surface is easy to scratch - do not rub it when cleaning.

2. Package Contents

1 VMA6593 monitor unit 2 Flush-mount trim bezel 3 Wiring harness 4 Owners Manual / Installation Guide
3. Installation Requirements
WARNING! Never install this monitor where it is visible from the drivers seat, or where it could injure any vehicle occupant in case of an accident. Ensure that your installation does not create risk of headstrike injury, and that the monitor will remain securely mounted in the case of an accident or sudden maneuver.
Precautions This unit is exclusively for cars with a negative ground, 12V power supply. Do not open the case. There are no user-serviceable parts inside. If you require asistance, consult your Clarion dealer or an authorized Clarion service center. 6
4. Installing the VMA6593
The VMA6593 is designed for custom installation. While a basic flush-mount bezel is supplied, you may need parts that are not included (depending on your installation). Clarion also offers optional mounting kits - the ZMT003 is a flexible gooseneck mount, and the PQE023 positions the monitor on the back of a vehicle headrest.
After you cut the opening, route the DIN-connector end of the wiring harness into the opening from the rear out the front. Insert the trim bezel and route the wiring harness through the opening in the rear. Firmly attach the bezel to the mounting surface and/or to the interior of the mounting surface.

The Clarion HRM100 and HRM150 headrest mounting kits are not
compatible with this monitor.
Wire harness opening Mounting tabs
WARNING! Always use great care when attaching anything to a vehicle! Visually inspect all sides of any potential screw location, to insure no damage will occur. If you have questions about this process, see your authorized Clarion dealer. Flush mounting The included trim bezel can be used to flush-mount the monitor. Before cutting the opening for the trim bezel, ensure that you will have sufficient clearance for the monitor and its rearlocated wiring harness.

Mounting screw holes

CAUTION! NEVER press on the surface of the screen! Gently press on the edges of the monitor case. If you find that you cannot insert the monitor without excessive force, you may need to check your wire harness position for interference with the insertion process. You may also need make the opening slightly larger.
Connect the wiring harness to the monitor, and tuck the excess wiring harness length carefully out of the way behind the bezel. Gently insert the monitor into the bezel. Press only on the edges of the monitor, not on the screen. You will hear a few soft clicks as the monitor locks into place. Inserting the monitor into the bezel:
Removing the monitor from the bezel To remove the monitor from the bezel, insert a flat card (such as a credit card) between the monitor case and the side of the bezel to release the spring clips.

Insert card

Custom Mounting using the threaded insert The base of the VMA6593 has a threaded insert (1/4 - 20). This insert can be used with the optional Clarion ZMT009 gooseneck mounting kit or with a 1/4 -20 machine screw in custom applications.

5. Wiring the VMA6593

The following pages display wiring diagrams for various VMA6593 configurations. Read the following precautions before wiring your system. Disconnect the negative battery terminal before making any wiring connections. Be particularly careful where you route wires. Keep them away from the engine, exhaust system, etc. Heat may damage wires. If the fuse should blow, make sure all connections are correct and no wires are damaged before replacing the fuse. Always use fuses that are the same amperage value as the original. When replacing a fuse, never let the battery side touch any metal part or any other wire. WARNING! Be sure to disconnect the battery (-) terminal before starting. This is to prevent short circuits during installation.

VMA6593 Connections

Clarion VMA 6593
Video input 2 Video input 1
CAUTION! Some non-Clarion automotive DVD and VCP source units use a similar connector for an external IR receiver, but use different pin polarity than the VMA6593! Connecting nonClarion source equipment to this connector could cause equipment damage not covered by the warranty! IR connector polarity:

(+) V ACC

IR receiver output
Black Ground Red +12V Accessory
ALWAYS use a 3A fuse on this connection!
DIN Connector Pin Assignments
Pin Description Red 12V (+) ACC Infrared receiver signal Black Ground (-) Yellow Video input 1 Video signal ground Not used Yellow video input 2 Not used

IR DATA LINE

VMA6593 Monitor with VS735 DVD Player

Video input 2

Audio output - to head unit with volume control or Clarion FM200 FM Modulator
Video input 1 Video input 1

Video output to monitor

A/V Auxiliary inputs

IR input

A/V Output VS 735

Red +12V Accessory

Power Harness

Black Ground

Optical digital output
Black - Ground Red +12V Accessory Yellow +12V Constant Power
VMA6593 with VS735 DVD Player and TTX001 TV Tuner
3-conductor "Y"-cable (not supplied) Red +12V ACC Black - Ground
Video output to monitor IR input
A/V Auxiliary inputs TTX 001 TV Tuner Antenna ZCB 001

Notes:

This system requires a 3.5mm stereo Y cable, Radio Shack
P/N 42-2496. A 3.5mm male-to-female stereo extension may also be required if the TTX001 and the VS735 are installed in separate locations (P/N varies by length).
The TTX001 is connected to the VS735 to allow the VS735 to
control both audio and video switching. Do not use the Video 2 input of the VMA6593 for the TTX001 in this instance.
Two VMA6593 monitors, with a VS735 DVD Player, a VDH910 VCP, and the WH200 Two-channel Wireless Headphone kit.
This system requires two 3.5mm
stereo Y cables, Radio Shack P/N 42-2463. These are used to allow the IR command lines to be shared between both source units and both monitors. A 3.5mm maleto-male extension may also be required (P/N varies by length).

VA700 Video Amplifier

VA700 Video Input

VMA 6593

VA 700 Video Output

Video input 1

The WH200 Two-channel
Wireless Headphone Kit allows headphone users to independently select from two different audio sources.

IR output

Video input 1 Video input 2
Mini stereo "Y"-cable (not supplied)
Two VA700 Video Amplfiers are
used to allow two monitors to operate from one video output.

Video Output

Mini stereo extention (not supplied) Mini stereo "Y"-cable (not supplied)

Clarion also makes several
audio integration and video switching products for more complex installations - see your Clarion dealer for more information on these products.
DVD POWER VCD CD MP3 L / R

SCN RDM

REPEAT TITLE

B A CHP TRK

REMAIN DOLBY ANGLE DIGITAL

L and R audio output

VS 735 DVD

WH 200 2-channel HP Kit

VDH 910 VCP

12/23/02, 10:37 PM

6. TROUBLESHOOTING
No picture. Press the [SOURCE] button to make sure the proper input is selected. If there is still no picture, press the [PICTURE ] button. If the menu appears, check the source unit and video connections. If no menu appears, check all fuses and power connections to the VMA6593 and the associated equipment.

7. SPECIFICATIONS

Supply voltage: 12V DC (9V-16V) Test voltage: 12V, negative ground Current consumption: Less than 750 milliAmps Operating Temperature: -1o C to 45o C (30o F to 113o F) Signal system: NTSC and PAL composite video 1.0Vp-p Screen: 6.5 diagonal, 144.4mm x 80.3 mm. Resolution: 1200 x 280 (280,000 pixels) Weight: 0.5 kg
The VMA6593 has an operating temperature range of
-1o C to 45o C (30o F - 113o F). If the temperature is outside this operating range, the unit will not turn on, or the screen may be slow to react to image changes. The monitor will function normally once it returns to its proper operating range.
With a DVD player and a widescreen DVD disc, there are black bars on the screen. Change the TV display mode to Wide in the DVD players Setup menu. After changing this setting, if there are still black bars, press the [WIDE] button on the front panel of the VMA6593.
The technical data and the design of the equipment may change for the sake of technical improvements without prior notice.
LIMITED WARRANTY INFORMATION

For USA and Canada only

This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase. Clarion ProAudio products, except for speakers, are covered by a two year limited warranty when installed by an authorized Clarion dealer. The conditions of this limited warranty and the extent of responsibility of Clarion Corporation of America (Clarion) under this limited warranty are as follows: 1. PROOF OF DATE OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT. IN THE CASE OF THE TWO (2) YEAR LIMITED WARRANTY FOR CLARION PROAUDIO PRODUCT, PROOF OF INSTALLATION BY AN AUTHORIZED DEALER IS REQUIRED. INFORMATION ABOUT CLARION AUTHORIZED WARRANTY SERVICE CENTERS MAY BE OBTAINED BY CONTACTING CLARION AT THE ADDRESS BELOW. 2. This limited warranty will become void if service performed by anyone other than an approved Clarion Warranty Service Center results in damage to the product. 3. This limited warranty does not apply to any product which has been subject to misuse, neglect or accident, or which has had the serial number altered, defaced or removed, or which has been connected, installed, adjusted or repaired, other than in accordance with the instructions furnished by Clarion. 4. This limited warranty does not cover car static or other electrical interferences, tape head or laser pick-up cleaning or adjustments, or labor costs for the removal or reinstallation of the unit for repair. 5. The sole responsibility of Clarion under this limited warranty shall be limited to the repair of the product or replacement of the product, at the sole discretion of Clarion.

6. Product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid. Clarion will not assume any responsibility for any loss or damage incurred in shipping. 7. ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE. UNDER NO CIRCUMSTANCES SHALL CLARION BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT. BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. 8. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE. 9. Should you have any difficulties with the performance of this product during the warranty period, please call or visit our web site (www.clarion.com) for a listing of Authorized Warranty Service Centers in your area. You may also contact Clarion at the address listed below. In USA: Clarion Corporation of America Attn: Customer Service Manager 661 W. Redondo Beach Blvd Gardena, CA. 90247-4201 1-800-GO-CLARION (310)327-9100 www.clarion.com In Canada: Clarion Canada, Inc. Warranty Service Center 2239 Winston Park Drive Oakville, Ontario L6H 5R1 (905)829-4600 www.clarioncanada.com