PREPARATION

Parts list

(Qty) Component Preassembled (1) Roto-molded subwoofer enclosure (1) 8"; 2 ohm subwoofer (1) 100W class "D" amplifier Loose Components (1) 3 wire harness w/ pigtail style connector (2) 1" self taping Phillips screws (1) 1/2" ground screw (1) Star washer (2) Flat 4 hole brackets (1) L shaped bracket (8) 3/4" pilot point Phillips screws

WIRING:

Note: Installer MUST disconnect speaker-input leads to amplifier when using line-level input

OVERVIEW

The Clarion Camouflage subwoofer system provides for the installation of a low frequency driver in an enclosure which is powered by a small low current, high power class "D" (Digital) amplifier. The advantage to using this type of amplifier is in the low current consumption of the amplifier at high power levels. The class "D" amplifier provided with this system will produce a rated 100W into a 2 ohm load. The woofer supplied with this system uses a voice coil with rated impedance of 2 ohms, and therefore is not considered a standard woofer. Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended.

PROCEDURE

Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work.

OUTLINE

Remove the head unit. Connect the Clarion "T" harness between the radio and factory wiring and route the harness extension to transmission hump of the vehicle. Install subwoofer enclosure. Test subwoofer enclosure and head unit functions (fade, balance, dim, etc.). Adjust subwoofer gain.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.
Ia. WIRING USING A CLARION T HARNESS
There are 2 methods to connect this product to the vehicle. Please refer to section Ia and Ib for each.
STEP 1: Remove the Radio. STEP 2: Connect the "T" Harness. A. Unplug factory wires from radio.
B. Plug the "T" harness in line with the radio wiring. SEE DIAGRAM 1. C. Connect the BLACK wire on "T" harness to radio chassis.
STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. STEP4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure.
STEP 5: TEST and SET the GAIN. A. Turn on the system and be sure all speakers are working properly. B. Set the subwoofer amplifier gain to a suitable level.
Ib. WIRING USING THE SUPPLIED HARNESS
STEP 1: Remove the Radio. STEP 2: Connect the wires. Yellow: Connect to Constant 12V Power Black: Connect to Radio Ground or Chassis Blue: Connect to Amp/Antenna Turn-on Lead Green: Connect to Left Rear Speaker (+) Positive Lead Green/Black: Connect to Left Rear Speaker (-) Negative Lead Violet: Connect to Right Rear Speaker (+) Positive Lead Violet/Black: Connect to Right Rear Speaker (-) Negative Lead STEP 3: Route the wire harness from the radio to transmission hump of the vehicle. STEP 4:
Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure. STEP 5: TEST and SET the GAIN. A. Turn on the system and be sure all speakers are working properly. B. Set the subwoofer amplifier gain to a suitable level.

RUN WIRE HARNESS

A. Route harness straight down from the radio to the vehicle floor. B. Fold back carpet on transmission hump. C. Put a small slit in the carpet about 12" away from the black floor vents. D. Route harness through the slit in the carpet. E. Ground the 8" black wire to the vehicle floor (be sure to use a wire wheel or sand paper if grounding to a painted surface).
III. INSTALL THE BRACKETS TO THE ENCLOSURE
A. Align the (2) flat 4-hole brackets to the dimples on the bottom of the enclosure. B. Attach each bracket with two pilot point screws (one hole of the bracket should extend out past the enclosure). C. Attach the L shaped bracket to the back of the enclosure; align the two vertical slots on the bracket with the dimples on the back of the enclosure.

IV. TEST THE ENCLOSURE

A. Plug in the Clarion T harness or hardwire the pigtail harness behind the radio. B. Place the enclosure into the vehicle (correct position is on the transmission hump). C. Plug in the wire harness to the enclosure. D. Gain the subwoofer enclosure (gain pod is located on the amplifier next to the wire harness connector, and is adjustable with a Phillips screw driver).
ATTACH THE ENCLOSURE TO VEHICLE
A. Be sure enclosure is in correct position. B. Cut a U shaped slit in the carpet at the two front bracket locations. C. Fold up carpet slits over the brackets. D. Screw in the front two bracket to the vehicle floor (or duct work depending on application) using the supplied 1" self-taping screws. E. Fold carpet slits back over to conceal the brackets. F. Attach the rear L bracket to the vehicle using (2) pilot point screws. This will require a right-angle drill attachment with a #2 Phillips bit.
VI. REASSEMBLE THE VEHICLE
A. Make sure all the wires are hidden. Then do the process in reverse order.
Clarion Corporation of America 661 West Redondo Beach Blvd Gardena, CA 90247 800-Go-Clarion www.clarion-usa.com 2000 Clarion Corporation, Gardena, CA
10 - PSWGMSU Rev. 1 (03/00 )

Clarion

PREPARATION

Parts list

(Qty) Component Preassembled (1) Roto-molded subwoofer enclosure (1) 8", 2 ohm subwoofer (1) 1DOW class "0" amplifier

PSW-GM-Su-sn/G/R

Camouflage Powered Subwoofer
Tahoe, Yukon, Suburban & Full Size Pick-up Fits '95-'99 GM SUV's listed above

020GMSUT

Loose Components (1)30 wire harness wI pigtail style connector (2) 1" self taping Phillips screws (1) 1/2" ground screw (1) Star washer (2) Flat 4 hole brackets (1) L shaped bracket (8) 3/4" pilot point Phillips screws

PIN SIDE

WIRING:

020GMSUR

Green Violet/Blk GreenlBlk Violet Blank Black Blue 8 Yellow
Note Installer MUST disconnect speaker-input leads to amplifier when using line-level input

OVERVIEW

The Clarion Camouflage subwoofer system provides for the installation of a low frequency driver in an enclosure which is powered by a small low current, high power class "0" (Digital) amplifier The advantage to using this type of amplifier is in the low current consumption of the amplifier at high power levels The class "0" amplifier provided with this system will produce a rated 100W into a 2 ohm load The woofer supplied with this system uses a voice coil with rated impedance of 2 ohms, and therefore is not considered a standard woofer Replacing the woofer with any driver having an impedance greater than 2 ohms will yield lower power output from the amplifier, and is not recommended

020GMSUG 020GMSUB

PROCEDURE
Proper installation of this product requires proper tools and knowledge of car audio principles. If you are not comfortable performing any of the outlined tasks below, contact a professional installation facility to perform the work.

OUTLINE

Remove the head unit Connect the Clarion "T" harness between the radio and factory wiring and route the harness extension to transmission hump of the vehicle Install subwoofer enclosure Test subwoofer enclosure and head unit functions (fade, balance, dim, etc) Adjust subwoofer gain
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING lWO CON DITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDE SIRED OPERATION.
WIRING USING A CLARION T HARNESS
There are 2 methods to connect this product to the vehicle. Please refer to section la and Ib for each.
STEP 1: Remove the Radio. STEP 2: Connect the "T" Harness. A Unplug factory wires from radio
B Plug the "T" harness in line with the radio wiring SEE DIAGRAM 1 C Connect the BLACK wire on "T" harness to radio chassis
STEP 3: Route the wire harness from the radio to transmission hump of the vehicle STEP4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure STEPS: TEST and SET the GAIN. A Turn on the system and be sure all speakers are working properly
B Set the subwoofer amplifier gain to a suitable level

(DIAG.1)

GAIN ADJUSTMENT. CONNECT TO GROUND
WIRING USING THE SUPPLIED HARNESS
STEP 1: Remove the Radio. STEP 2: Connect the wires. Yellow Connect to Constant 12V Power Black Connect to Radio Ground or Chassis Blue Connect to Amp/Antenna Turn-on Lead Green Connect to Left Rear Speaker (+) Positive Lead Green/Black Connect to Left Rear Speaker (-) Negative Lead Violet Connect to Right Rear Speaker (+) Positive Lead VioleUBlack Connect to Right Rear Speaker (-) Negative Lead STEP 3: Route the wire harness from the radio to transmission hump of the vehicle STEP4: Connect the amplifier ground wire to a clean chassis ground near the subwoofer enclosure STEPS: TEST and SET the GAIN. A Turn on the system and be sure all speakers are working properly
Using the Supplied Harness

(DIAG.2)

CONNECT TO GROUND

RUN WIRE HARNESS

A Route harness straight down from the radio to the vehicle floor B Fold back carpet on transmission hump C Put a small slit in the carpet about 12" away from the black floor vents
Route harness through the slit in the carpet
E Ground the 8" black wire to the vehicle floor (be sure to use a wire wheel or sand paper if grounding to a painted surface)
INSTALL THE BRACKETS TO THE ENCLOSURE
A Align the (2) flat 4-hole brackets to the dimples on the bottom of the enclosure B Attach each bracket with two pilot point screws (one hole of the bracket should extend out past the enclosure) C Attach the OLD shaped bracket to the back of the enclosure, align the two vertical slots on the bracket with the dimples on the back of the enclosure

(DrAG 3)

">"
Flat Four Hole Brack.t 1/2" rdot Point Phdlips Head

Screws (2)

~l<>.'~ !! Ph_lipsPilot Paint 1/2" Head

Strews (2)

Rat Four Hole Bracket

TEST THE ENCLOSURE

A Plug in the Clarion DID harness or hardwire the pigtail harness behind the radio B Place the enclosure into the vehicle (correct position is on the transmission hump) C Plug in the wire harness to the enclosure
Gain the subwoofer enclosure (gain pod is located on the amplifier next to the wire harness connector, and is adjustable with a Phillips screw driver)
ATTACH THE ENCLOSURE TO VEHICLE
A Be sure enclosure is in correct position B Cut a DUO shaped slit in the carpet at the two front bracket locations C Fold up carpet slits over the brackets D Screw in the front two bracket to the vehicle floor (or duct work depending on application) using the supplied 1" self-taping screws E Fold carpet slits back over to conceal the brackets F Attach the rear OU:bracket to the vehicle using (2) pilot point screws This will require a right-angle drill attachment with a #2 Phillips bit

REASSEMBLE THE VEHICLE

A Make sure all the wires are hidden Then do the process in reverse order
Clarion Corporation of America 661 West Redondo Beach Blvd Gardena, CA 90247 800-Go-Clarion www clarion-usa com' 2000 Clarion Corporation, Gardena, CA
10 - PSWGMSU Rev 1 (03/00)

CAl AUDIO

BEyeND

Prodnut Registration

for USA and Canada only

IMPORTANT:

1. Detach this section of the card and keep it with your records. 2. Retain your sales receipt to validate warranty service. 3. If you purchased a Clarion ADX Series, Pro Video or Pro Audio product, be sure to complete the box on the last page of this form. Information on Clarion authorized Warranty Centers may be obtained by writing Clarion Corporation at the address below or by calling

1-800-GO-CLARION.

In USA: Clarion Sales Corporation Warranty Service Center 661 West Redondo Beach Blvd Gardena, CA 90247 (310) 327-9100 In Canada Clarion Canada, Inc Warranty Service Center 2239 Winston Park Drive Oakville, Ontario L6H 5R1 (416) 829-4600
www.clarionmultimedia.com

clarion

WAR RAN T YIN FOR MAT ION
TEAR THIS PAGE OFF AND KEEP IT WITH YOUR RECEIPT!

This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase The conditions of this warranty and the extent of the responsibility of Clarion Corporation under this warranty are as follows
1 PROOF OF DATE OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT. INFORMATION ABOUT CLARION AUTHORIZED WARRANTY SERVICE CENTERS MAY ALSO BE OBTAINED BY CONTACTING OR WRITING CLARION CORPORATION AT THE ADDRESS LISTED ON THE FRONT OF THIS CARD. 2 This warranty will become void if service performed by anyone other than an approved Clarion Warranty Service Center results in damage to product 3 This warranty does not apply to any product which has been subject to misuse, neglect or accident, or which has had the serial number altered, defaced or removed, or which has been connected, installed, adjusted or repaired, other than in accordance with the instructions furnished by Clarion Corporation 4 This warranty does not cover car static or other electrical interferences, tape head cleaning or adjustments, or labor costs for the removal or reinstallation of the unit for repair 5 The sole responsibility of Clarion Corporation under this Warranty shall be limited to the repair or replacement thereof, at the sole discretion of Clarion Corporation 6 If it becomes necessary to send the product or any defective part to Clarion Corporation or an authorized warranty service station, the product must be shipped in its original carton or equivalent carton, fully insured, with shipping charges prepaid Clarion Corporation will not assume any responsibility for any loss or damage incurred in shipping 7 ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE UNDER NO CIRCUMSTANCES SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU 8 THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 9 Should you have any difficulties with the performance of this product during warranty, or with any Clarion authorized service centers, you may contact the Clarion National Service Managers at the address listed on the front of this card or call 1-800-GO-CLARION for a listing of Authorized Warranty Service Centers in your area

-.:l CD

CD C'> CD

D!!DmPRODUCT

REGISTRATION
Thank you for selecting a high-quality product from Clarion We hope you are completely satisfied with your purcnase We'd like to help serve you better by finding out more about your reasons for choosing Clarion Please take a few moments to fill out the registration information on this card and answer a few questions about yourself and your product Then, return the card to Clarion within 10 days of purchase Your answers will be kept strictly confidential We appreciate your response!
In Canada, place the card in an envelope and mail to: Clarion Canada, Inc, Warranty Service Center, 2239 Winston Park Drive, Oakville, Ontario L6H 5R1
. D Mr. 0 Ms. D Mrs. D Miss
: II What Clarion product did you purchase?

Multimedia

Car Audio
D Color LCD Display/Control Unit Color LCD Display Voice-Activated Navigation System Video Cassette Player
AM/FM cassette AM/FM CD Player CD Changer Equalizer/DSP Processor Module
D AM/FM Cassette/CD Player
sDTVTuner Rear Vision Camera 7DOther
130 Amplifier _ 140 Speakers
II What is the name of the store where you purchased this product?
This product is warranted against all defects in material workmanship for a period of one year from the date of original purchase The conditions of this warranty and the extent of the responsibility of Clarion Corporation under this warranty are as follows.
1 PROOF OF DATE OF PURCHASE WILL BE REQUIRED FOR WARRANTY SERVICE OF THIS PRODUCT. INFORMATION ABOUT CLARION AUTHORIZED WARRANTY SERVICE CENTERS MAY ALSO BE OBTAINED BY CONTACTING OR WRITING CLARION CORPORATION AT THE ADDRESS LISTED ON THE FRONT OF THIS CARD. 2 This warranty will become void if service performed by anyone other than an approved Clarion Warranty Service Center results in damage to product 3 This warranty does not apply to any product which has been subject to misuse, neglect or accident, or which has had the serial number altered, defaced or removed, or which has been connected, installed, adjusted or repaired, other than in accordance with the instructions furnished by Clarion Corporation 4 This warranty does not cover car static or other electrical interferences, tape head cleaning or adjustments, or labor costs for the removal or reinstallation of the unit for repair 5 The sole responsibility of Clarion Corporation under this Warranty shall be limited to the repair or replacement thereof, at the sole discretion of Clarion Corporation 6 If it becomes necessary to send the product or any defective part to Clarion Corporation or an authorized warranty service station, the product must be shipped in its original carton or equivalent carton, fUlly insured, with shipping charges prepaid Clarion Corporation will not assume any responsibility for any loss or damage incurred in shipping 7 ALL IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW SHALL HAVE NO GREATER DURATION THAN THE WARRANTY PERIOD SET FORTH ABOVE UNDER NO CIRCUMSTANCES SHALL CLARION CORPORATION BE LIABLE FOR ANY LOSS OR DAMAGE, DIRECT OR CONSEQUENTIAL, ARISING OUT OF THE USE OR INABILITY TO USE THE PRODUCT BECAUSE SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR EXCLUSIONS OR LIMITATIONS OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU 8 THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE 9 Should you have any difficulties with the performance of this product during warranty, or with any Clarion authorized service centers, you may contact the Clarion National Service Managers at the address listed on the front of this card or call 1-800-GO-CLARION for a listing of Authorized Warranty Service Centers in your area

Cl III Cl ::0

CD III

'Cl III

'Cl C'l
III Which of the following products/services do you own or intend to buy within the next 18 months?
Intend to buy Own Intend to buy
Home Desktop PC Laptop Computer Color Monitor CD-ROM Computer Speakers Color Printer Modem Large Screen TV (35" or larger)

150 160

Satellite System/Service Cellular Telephone Pager Call Waiting Karaoke Vehicle Navigation System Vehicle Security System

170 laD 230

2aO 290 300
.=- II What type of computer do you own? -: III Which on-line service/network do you subscribe to?.
illS this your first Clarion purchase?

10 IBM PC or Clone

10 1st purchase

0 2nd purchase

0 3rd or more

0 Macintosh or Clone

0 Do Not Own
10 America Online 0 CompuServe

70 Other

50 Internet 60 Prodigy
0 Do not have service/access

3D GEnie

CAMOUFLAGE POWERED SUBWOOFER WARRANTY INFORMATION
Clarion offers one-year warranty coverage on Camouflage Powered Subwoofers ONLY if the product is installed at the same location where purchased

Cl Cl. til.

To obtain one-year warranty coverage on your Camouflage Powered Subwoofer, complete this section in full and return it along with a copy of your receipt and the attached product registration information in an envelope addressed to:
Clarion Sales Corporation P.O Box 863 Brea, CA 92822-0863

"'

ONE-YEAR WARRANTY NOT VALID UNLESS THE SECTION ABOVE IS COMPLETED IN FULL AND RETURNED WITH A COPY OF YOUR RECEIPT.

CAl AU"

PLEASE PLACE FIRST-CLASS STAMP
(Post Office will not deiiver without proper postage.)
CLARION SALES CORPORATION
PO BOX 863 BREA CA 92822-0863