Owners manual Mode demploi Manual de instrucciones

RAX650Dz

AM/FMCASSETTEPLA YER WITHCD/MDCHANGERCONTROL LECTEURDECASSETTEAM/FMAVEC COMMANDEDECHANGEURCD/MD RADIODEAM/FMYREPRODUCTORDE CASETESCONCONTROLDECAMBIADORDE DISCOSCOMAPCTOS/MINIDISCOS

Clarion Co., Ltd.

1998/11 (AC)
All Rights Reserved. Copyright 1998: Clarion Co., Ltd. Printed in China / Imprim en Chine / Inpreso en China

PE-1650B 280-7248-00

Thank you for purchasing the Clarion RAX650Dz. Please read this owners manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. This manual includes the operating procedures of the CD changer, MD changer and TV tuner connected via the CeNET cable. The CD changer, MD changer and TV tuner have their own manuals, but no explanations for operating them are described.

Contents

1. FEATURES..... 3 2. PRECAUTIONS.... 3 Handling Cassette Tapes.... 4 Flip Down Panel.... 4 3. CONTROLS.... 5 4. NOMENCLATURE.... 6 Names of Buttons.... 6 Display Items..... 6 5. DCP..... 7 6. REMOTE CONTROL..... 8 Inserting the Batteries.... 8 Functions of Remote Control Unit Buttons... 9 7. OPERATIONS.... 10 Basic Operations..... 10 Radio Operations.... 12 Tape Operations.... 14 Other Handy Functions..... 16 8. OPERATIONS OF ACCESSORIES... 17 CD Changer Operations.... 17 MD Changer Operations.... 19 TV Operations.... 20 9. TROUBLESHOOTING.... 22 10. ERROR DISPLAYS.... 23 11. SPECIFICATIONS.... 24

6. REMOTE CONTROL

Receiver for remote control unit

1. FEATURES

s s s s s s s s s s Rotary Encoder Volume Control with Illuminated Search Key Touch-n-Go Flip Down Detachable Face Capability to Read CD TEXT Data from Clarion Compatible CD Changer Z-Enhancer with 3 Adjustment Modes CeNET with Balanced Audio Line Transmission and Dynamic Noise Canceling FM Reception System Full Logic Tape Transport with True Function / Auto Reverse with Dual Azimuth Adjust Dolby B Noise Reduction 4-Channel RCA Line Level Output with Fader Control 160W (40W4) Maximum Power Output

Handling Cassette Tapes

Using any of the following types of cassette tapes can cause malfunctions. Cassette tapes with low recording levels Cassette tapes in which the unrecorded section between tracks is shorter than 4 seconds Cassette tapes with noise or the like recorded between tracks Cassette tapes on which there are long unrecorded sections in the middle of a track Avoid using cassettes of 120 minutes or longer. (Such cassettes have extremely thin tape, so the tape can become stretched or cut.) Periodically play a cleaning cassette in the player to clean the head. Keep magnet items like magnets, and iron and steel items like screwdrivers away from both cassette tapes and the tape head in the player. Do not oil the cassette mechanism. Do not use any cassette tapes with peeling labels or deformed cases. Such cassette tapes can cause breakdowns. When not using the player, always take the cassette out of the mechanism. Exposing a cassette to direct sunlight, extreme temperatures or high humidity can damage the cassette.
Operating range: 30 in all directions

Handling precautions

Slack in the tape can cause malfunctions. In particular for prerecorded cassette tapes and 90-minute tapes, take up any slack in the tape before inserting it into the cassette player.

Remote control unit

Signal transmitter

2. PRECAUTIONS

This unit uses a precision mechanism. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

CAUTION

CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. INFORMATION FOR USERS:. CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

Flip Down Panel

The RAX650Dz uses a flip-down structure that makes possible large-size displays.
When opening and closing the FLIP DOWN PANEL, be careful not to catch your fingers. They could be injured. 1. Always use the RAX650Dz with the FLIP DOWN PANEL closed. 2. Do not force operations or use this device abnormally when opening or closing the FLIP DOWN PANEL.

Inserting the Batteries

1. Turn the remote control unit over, then slide the rear cover in the direction of the arrow. 2. Insert the AA (UM-3/1.5V) batteries that came with the remote control unit facing in the directions shown in the figure, then close the rear cover.

AA (UM-3/1.5V) Batteries

3. Do not use the FLIP DOWN PANEL as a tray to place objects on when it is open. 4. When closing the FLIP DOWN PANEL, do not press the OPEN button 1. 5. Strong impacts to the operating or display section can cause damage or deformation. 6. If the FLIP DOWN PANEL does not open fully, gently open it with your hand.

Notes:

Using batteries improperly can cause them to explode. Take note of the following points: When replacing batteries, replace both batteries with new ones. Do not short-circuit, disassemble or heat batteries. Do not dispose of batteries into fire or water. Dispose of spent batteries properly.

Rear cover

Rear side
Be sure to unfold and read the next page. Veuillez dplier et vous rfrer la page suivante. Cercirese de desplegar y de leer la pgina siguiente.

RAX650Dz

3. CONTROLS / LES COMMANDES / CONTROLES
Source unit / Appareil pilote / Unidad fuente

4. NOMENCLATURE

Note: Be sure to read this chapter referring to the front diagrams of chapter 3. CONTROLS on page 5 (unfold).

5. DCP

The control panel can be detached to prevent theft. When detaching the control panel, store it in the DCP (DETACHABLE CONTROL PANEL) case to prevent scratches. We recommend taking the DCP with you when leaving the car.

Names of Buttons

1 OPEN button 2 ENT (enter) button
8 Z-EHCR (z-enhancer) button 9 Preset buttons (1 to 6) Direct buttons (1 to 6) (7 to 12) 0 DISP (display) button ! ISR (instant station recall) button @ BND (band) button PROG (program) button # A-M (audio mode) button LD (loudness) button $ SEARCH button % Rotary knob Cassette tape insertion slot & Eject button

Removing the DCP

1. Hold down POWER button 3 for 1 second or longer to turn off the power.

Attaching the DCP

1. Insert the right side of the DCP into the source unit. 2. Insert the left side of the DCP into the source unit.
Play/pause button 3 POWER button FNC (function) button 4 TITLE button ADJ (adjust) button 5 SCN (scan) button PS/AS (preset scan/auto store) button 6 RPT (repeat) button BLS (blank skip) button 7 DOLBY NR button RDM (random) button
With the FLIP DOWN PANEL opened / Ouverture du PANNEAU RABATTABLE / Apertura del PANEL ABATIBLE
2. Deeply push in OPEN button 1 to unlock the FLIP DOWN PANEL.
If the FLIP DOWN PANEL does not open fully, gently open it with your hand.
The DCP can easily be damaged by shocks. After removing it, be careful not to drop it or subject it to strong shocks. If the FLIP DOWN PANEL is kept open, the DCP may drop due to vibration of the car. This results in damage to the DCP. So close the FLIP DOWN PANEL or remove the DCP to store into the case. The connector connecting the source unit and the DCP is an extremely important part. Be careful not to damage it by pressing on it with fingernails, screwdrivers, etc. Note: If the DCP is dirty, wipe off the dirt with a soft, dry cloth only.

Display Items

1 Cassette tape in indication 2 Dolby B NR indication 3 LD (loudness) indication 4 A-M (audio mode) indication 5 Function mode indication
The names of modes being selected, etc. are displayed.
! Long title indication @ Operation status indication
The frequency, play time, clock, etc. are displayed.
3. Pull the DCP toward you and remove it.
# RDM (random) indication $ RPT (repeat) indication % SCN (scan) indication BLS (blank skip) indication & BAND indication * CD/MD changer mode indication ( TRACK indication 4. Close the HOLD FLAP.

Display / Afficheur / Visualizador
6 MANU (manual) indication 7 ST (stereo) indication 8 Z-EHCR (z-enhancer) indication 9 DISC indication 0 Preset channel indication (1 to 6) Disc number indication (1 to 12)
The disc numbers corresponding to the discs in the CD or MD changer light.

HOLD FLAP

Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas.
Be sure to close the HOLD FLAP for safety when removing the DCP.