Handling Compact Discs

Use only compact discs bearing the or mark.

Storage

Do not expose compact discs to direct sunlight or any heat source. Do not expose compact discs to excess humidity or dust. Do not expose compact discs to direct heat from heaters.
Do not play heart-shaped, octagonal, or other specially shaped compact discs. Some CDs recorded in CD-R/CD-RW mode may not be usable.

Handling

Compared to ordinary music CDs, CD-R and CD-RW discs are both easily affected by high temperature and humidity and some of CD-R and CD-RW discs may not be played. Therefore, do not leave them for a long time in the car. New discs may have some roughness around the edges. If such discs are used, the player may not work or the sound may skip. Use a ball-point pen or the like to remove any roughness from the edge of the disc.

Ball-point pen Roughness

Cleaning
To remove fingermarks and dust, use a soft cloth and wipe in a straight line from the center of the compact disc to the circumference. Do not use any solvents, such as commercially available cleaners, anti-static spray, or thinner to clean compact discs. After using special compact disc cleaner, let the compact disc dry off well before playing it.
Never stick labels on the surface of the compact disc or mark the surface with a pencil or pen. Never play a compact disc with any cellophane tape or other glue on it or with peeling off marks. If you try to play such a compact disc, you may not be able to get it back out of the CD player or it may damage the CD player. Do not use compact discs that have large scratches, are misshapen, cracked, etc. Use of such discs may cause misoperation or damage. To remove a compact disc from its storage case, press down on the center of the case and lift the disc out, holding it carefully by the edges. Do not use commercially available CD protection sheets or discs equipped with stabilizers, etc. These may damage the disc or cause breakdown of the internal mechanism.
Be sure to unfold and read the next page. / Veuillez dplier et vous rfrer la page suivante. Cercirese de desplegar y de leer la pgina siguiente. / Assicurarsi di aprire e leggere la pagina successiva.

English

4. NOMENCLATURE
Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
Names of the Buttons and their Functions

[ PWR ] button

Press the button to turn on the power. Press and hold the button for 1 second or longer to turn off the power. Switches the operation mode among the radio mode, etc.

[ A-M ] button

Press and hold the button for 1 second or longer to switch the MAGNA BASS EXTEND on or off. Use the button to switch to the audio mode (sub woofer, bass/ treble, balance/fader, Z-Enhancer plus adjustment).

[SCN] button

Performs scan play for 10 seconds for each track while in the CD mode.

[ w ], [ z ] button

Press the buttons to increases or decreases the volume.

[ a ], [ d ] button

Selects a station while in the radio mode or selects a track when listening to a CD. These buttons are also used to make various settings. Press and hold the button for 1 second or longer to switches the fast-forward/fast-backward.

[ RPT ] button

Repeat play while in the CD mode.

[ HOOK ]

Open the door by push up the hook.

Stores a station into memory or recall it directly.
Switches the band. When the button is pressed and held, switches seek tuning or manual mode.

Selects a station.

Display Items
Z-Enhancer Plus indication Operation status indication Titles, frequency, PS names, clock, etc. are displays.
: Preset channel indication (1 to 6) Disc number indication (1 to 6) : SIRIUS indication : Category indication : MAGNA BASS EXTEND indication
: Disc indication : Scan indication : Repeat indication : Random indication : Stereo indication : Manual indication : Enter indication : Mute indication

LCD Screen

In extreme cold, the screen movement may slow down and the screen may darken, but this is normal. The screen will recover when it returns to normal temperature.
I XMD3 following operations are enabled by remote control with the Wired Remote Control Unit MR301RC (sold separately).
WIRED REMOTE CONTROL UNIT
Operation status indication Frequency, clock, etc. are displays.
Preset channel indication (1 to 6) Disc number indication (1 to 6)

[ ], [ ] [MUTE] [SOURCE]

[BAND]

[ w ], [z]

: Stereo indication SAT : SIRIUS indication : Mute indication

CAUTION

Be careful about adjusting the volume, as turning on the power while the volume is raised to its maximum may harm your hearing.
Changing the disc (in changer mode) Each time the [ BAND ] button is pressed, the disc switches in the following order: 1..

[ SOURCE ] Button

Turning on and off the power Press the [ SOURCE ] button to turn the power on and press and hold it for 1 second or longer to turn the power off. Changing the operation mode Each time the [ SOURCE ] button is pressed, the mode switches in the following order: Radio mode SIRIUS mode CD mode CD changer mode MD changer mode TV mode AUX mode Radio mode..

[ MUTE ] Button

Press the [ MUTE ] button. The sound is muted immediately. To cancel, press the [ MUTE ] button again.

] Buttons

Selecting tracks (in changer mode or CD mode) Press the [ ] button to start playback from the beginning of the ] button to start playback from the following track. Press the [ beginning of the current track. If pressed again, the track moves to the previous one. Fast-forward and fast-backward (in changer mode or CD mode) Press and hold the [ ] button to fast-forward the disc. Press and hold the [ ] button to fast-backward the disc.
Pressing and holding the [ ] or [ ] buttons for 1 second or longer will move forward or backward 3 times faster than normal play, and pressing and holding it for 3 seconds or longer will do the operation 30 times faster.

3. When the adjustment is complete, press the [ A-M ] button several times until the function mode is reached.
Adjusting the Z-Enhancer Plus
Adjusting the bass (Gain, Frequency, Q-curve)
This adjustment can be performed when the Z-Enhancer Plus is set to CUSTOM. 1. Press the [ A-M ] button and select BASS. 2. Press the [ w ] button emphasizes the bass. Press the [ z ] button attenuates the bass.
The factory default setting is B<G 0>. (Adjustment range: 6 to +6)
1. Press the [ Z+ ] button and select the Z-Enhancer Plus mode to adjust. 2. Press the [ A-M ] button and press the [ w ] button adjusts in the + direction; press the [ z ] button adjusts in the - direction. G When B-BST 0 is selected, you can adjust the bass in the range of -3 to 3. G When IMPACT 0 is selected, you can adjust the bass and treble in the range of -3 to 3. G When EXCITE 0 is selected, you can adjust the bass and treble in the range of -3 to 3.
Press and hold the [ Z+ ] button for 2 seconds or longer to change to the CUSTOM mode. Bass/treble characteristics become flat and the indication Z+FLAT is shown in the display. Press the [ Z+ ] button again to change to the Z+ OFF mode.
3. Press the [ d ] or [ a ] button to select B<F 60>. Press the [ w ] or [ z ] button to select the frequency.
The factory default setting is B<F 60>.(Adjustment 60/100/200 Hz)
4. Press the [ d ] or [ a ] button to select B<Q 1>. Press the [ w ] or [ z ] button to select the Q-curve.
The factory default setting is B<Q 1>.(Adjustment 1/1.25/1.5/2)
5. When the adjustment is complete, press the [ A-M ] button several times until the function mode is reached.
Turning on/off MAGNA BASS EXTEND
The MAGNA BASS EXTEND does not adjust the low sound area like the normal sound adjustment function, but emphasizes the deep bass sound area to provide you with a dynamic sound.
The factory default setting is off.
Adjusting the treble (Gain, Frequency)
This adjustment can be performed when the Z-Enhancer Plus is set to CUSTOM. 1. Press the [ A-M ] button and select TREBLE. 2. Press the [ w ] button emphasizes the treble. Press the [ z ] button attenuates the treble.
The factory default setting is T<G 0>. (Adjustment range: 6 to +6)
3. Press the [ d ] or [ a ] button to select T<F 10>. Press the [ w ] or [ z ] button to select the frequency.
The factory default setting is T<F 10>.(Adjustment 10 kHz/15 kHz)

1. Press and hold the [ A-M ] button for 1 second or longer to turn on the MAGNA BASS EXTEND effect. M-B EX lights in the display. 2. Press and hold the [ A-M ] button for 1 second or longer to turn off the MAGNA BASS EXTEND effect. M-B EX goes off from the display.
4. When the adjustment is complete, press the [ A-M ] button several times until the function mode is reached.

Adjusting the balance

1. Press the [ A-M ] button and select BAL 0. 2. Press the [ w ] button emphasizes the sound from the right speaker, press the [ z ] button emphasizes the sound from the left speaker.
The factory default setting is BAL 0. (Adjustment range: L13 to R13)

Radio Operations

FM reception
For enhanced FM performance the tuner includes signal actuated stereo control, Enhanced Multi AGC, Impulse noise reduction curcuits and Multipath noise reduction circuits.

Seek tuning

1. Press the [ BAND ] button and select the desired band (FM or AM).
If MANU is lit in the display, press and hold the [ BAND ] button for 1 second or longer. MANU in the display goes off and seek tuning is now available.
Changing the reception area
This unit is initially set to USA frequency intervals of 10kHz for AM and 200kHz for FM. When using it outside the USA, the frequency reception range can be switched to the intervals below. U.S. standard (Initial setting) Frequency AM spacing Frequency range FM Frequency spacing Frequency range 10 kHz 530 to 1,710 kHz 200 kHz 87.9 to 107.9 MHz Europe standard 9 kHz 531 to 1,602 kHz Seek:100 kHz Manual:50kHz 87.5 to 108 MHz Other countries 9 kHz 531 to 1,629 kHz 50 kHz 87.0 to 108 MHz
2. Press the [ a ] or [ d ] button to automatically seek a station. When the [ d ] button is pressed, the station is sought in the direction of higher frequencies; if the [ a ] button is pressed, the station is sought in the direction of lower frequencies.

Manual tuning

There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In the quick tuning mode, you can quickly tune the desired frequency. 1. Press the [BAND] button and select the desired band (FM or AM).
If MANU is not lit in the display, press and hold the [BAND] button for 1 second or longer. MANU is lit in the display and manual tuning is now available.
Setting the reception area
Any station preset memories are lost when the reception area is changed.
2. Tune in a station. G Quick tuning: Press and hold the [ a ] or [ d ] button for 1 second or longer to tune in a station. G Step tuning: Press the [ a ] or [ d ] button to manually tune in a station.

1. Press the [ BAND ] button and select the desired radio band (FM or AM). U.S. standard (initial setting) 2-1. While pressing the [ A-M ] button, press and hold the number 1 of the [ DIRECT ] buttons for 2 seconds or longer. Europe standard (new setting) 2-1. While pressing the [ A-M ] button, press and hold the number 3 of the [ DIRECT ] buttons for 2 seconds or longer. Other countries (new setting) 2-1. While pressing the [ A-M ] button, press and hold the number 2 of the [ DIRECT ] buttons for 2 seconds or longer.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6-FM3, 6-AM) exist to store individual radio stations in memory. Pressing the corresponding [ DIRECT ] button recalls the stored radio frequency automatically. 1. Press the [ BAND ] button and select the desired band (FM or AM). 2. Press the corresponding [ DIRECT ] button to recall the stored station.
Press and hold one of the [ DIRECT ] buttons for 2 seconds or longer to store that station into preset memory.

Listening to the radio

1. Press the [ PWR ] button and select the radio mode. The frequency or PS appears in the display.
PS: Programme service name

Manual memory

1. Select the desired station with seek tuning, manual tuning or preset tuning. 2. Press and hold one of the [ DIRECT ] buttons for 2 seconds or longer to store the current station into preset memory.
2. Press the [ BAND ] button and select the radio band. Each time the button is pressed, the radio reception band changes in the following order: FM1 FM2 FM3 AM FM1. 3. Press the [ a ] or [ d ] button to tune in the desired station.

Auto store

Auto store is a function for storing up to 6 stations that are automatically tuned in sequentially. If 6 receivable stations cannot be received, a previously stored station remains unoverwritten at the memory position. 1. Press the [ BAND ] button and select the desired band (FM or AM). 2. Press and hold the [ P/A ] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.

Clearing titles

1. Select and play a CD in the CD changer or tune in to a TV station for which you want to clear the title. 2. Press the [ D ] button and display the sub. 3. Press the [ T ] button. Titles appears in the display and the display switches to the title input display. 4. Press the [ BAND ] button. 5. Press and hold the [ s ] button for 2 seconds or longer to clear the title and cancel title input mode.

Repeat play

The repeat play continuously plays the current track. This function continues automatically until it is cancelled. 1. Press the [ RPT ] button. RPT lights in the display and the current track is repeated. 2. To cancel the repeat play, press the [ RPT ] button again. RPT goes off from the display and normal play resumes.

Random play

The random play selects and plays individual tracks on a disc in no particular order. This function continues automatically until it is cancelled. 1. Press the [ RDM ] button. RDM lights in the display, an individual track is selected randomly and play begins. 2. To cancel the random play, press the [ RDM ] button again. RDM goes off from the display and normal play resumes.
Setting the low pass filter
This function allows you to set the low-pass filter for sub-woofer output.
The factory default setting is LPF 120.
1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button and select SW LPF. 3. Press the [ w ] or [ z ] button to setting changes as following order: LPF 80 LPF 50 REAR LPF 120 4. Press the [ T ] button to return to the previous mode.

Dimmer control

You can setting the dimmer control on or off.
The factory default setting is ON.
6. Press the [ s ] button to store the time into memory. 7. Press the [ T ] button to return to the previous mode.
You cannot set the clock when it is displayed with only the ignition on. If you drain or remove the cars battery or take out this unit, the clock is reset. While setting the clock, if another button or operation is selected, the clock set mode is canceled.
1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button to select DIMMER. 3. Press the [ w ] or [ z ] button to select ON or OFF. 4. Press the [ T ] button to return to the previous mode.

Turning the screen saver function on or off
This unit is provided with the screen saver function. You can turn on or off this function. If the button operation is performed with the screen saver function on, the operation display corresponding to the button operation is shown for about 30 seconds and the display returns to the screen saver display.
The factory default setting is SS.
Adjusting the display contrast
You can adjust the display contrast to match the angle of instalation of the unit.
The factory default setting is 5.(Adjustment level 1 to 8)
1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button and select CONTRAST. 3. Press the [ w ] or [ z ] button to adjust the contrast. 4. Press the [ T ] button to return to the previous mode.
Setting the method for title scroll
Set how to scroll in CD-TEXT or MD.
1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button and select SCROLL. 3. Press the [ w ] or [ z ] button to select ON or OFF. G ON : To scroll automatically. G OFF : To scroll just 1 time when the title was changed or the title key was pressed. 4. Press the [ T ] button to return to the previous mode.
1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button and select SCRN SVR. 3. Press the [ s ] button. 4. Press the [ w ] or [ z ] button to setting changes as following order: MESSAGE SS(screen saver) OFF (off) 5. Press the [ s ] button to store the setting. 6. Press the [ T ] button to return to the previous mode.
The following illustration presents one of the patterns which are shown when the screen saver function is turned on.
Entering message information
Message up to 30 characters long can stored in memory and display for any mode. Any of the messages input can be displayed as one of the patterns for the screen saver function.
The factory default setting is WELCOME TO CLARION.

AUX function

This system has an external RCA input so you can listen to sounds and music from external devices connected to this unit.
Selecting AUX IN sensitivity
Make the following settings to select the sensitivity when sounds from external devices connected to this unit are difficult to hear even after adjusting the volume.

Selecting a CD or MD

1. Press the [ UP ] or [ DN ] button to select the desired disc.
If a CD is not loaded in a slot of magazine, pressing the [ UP ] or [ DN ] button can not work. If an MD is not loaded in a slot of MD changer, pressing the [ UP ] or [ DN ] button can not work.
CD-ROM discs cannot be played in the CD changer.
1. Press the [ s ] button to pause play. PAUSE appears in the display. 2. To resume play, press the [ s ] button again.
This unit can display title data for CD-text CDs and user titles input with this unit.
Title data for CD-text CDs can be displayed with this unit only when it is connected to CDC655Tz.
G When connected to DCZ625 or CDC1255z 1. Press the [ D ] button to display the title. G When connected to CDC655Tz 1. Press the [ D ] button to display the title. 2. Each time you press and hold the [ D ] button for 1 second or longer, the title display changes in the following order: User title (disc) CD-text title (disc) Artist name CD-text title (track) User title (disc).
If the CD playing is not a CD-text CD or no user title has been input, NO TITLE appears in the display. If a CD-text CD is not input its disc title or a track title, NO TITLE appears in the display.
Scan play locates and plays the first 10 seconds of each track on a disc automatically. This function continues on the disc until it is cancelled.
Switching disc titles and track titles(MD)
This unit can display disc titles and track titles already entered on MDs.
Titles cannot be entered for MDs with this unit.
1. Press the [ SCN ] button to start track scanning. SCN lights in the display. 2. To cancel the scan play, press the [ SCN ] button again. SCN goes off from the display and the current track continues to play.
1. Press the [ D ] button to display the title. The disc title or track title is displayed. 2. Each time you press and hold the [ D ] button for 1 second or longer, the display toggles between the disc title and the track title.

Disc scan play

Disc scan play locates and plays the first 10 seconds of the first track on each disc in the currently selected CD (MD) changer. This function continues automatically until it is cancelled.
Disc scan play is useful when you want to select a desired CD (MD).
If an MD is not input its disc title or a track title, NO TITLE appears in the display.
1. Press and hold the [ SCN ] button for 1 second or longer. DISC and SCN light in the display and disc scan play starts.
2. To cancel disc scan play, press the [ SCN ] button again. DISC and SCN go off from the display and the current track continues to play.

1. Press the [ BAND ] button and select the desired TV band (TV1 or TV2).

Disc random play

The disc random play selects and plays individual tracks or discs automatically in no particular order. This function continues automatically until it is cancelled. 1. Press and hold the [ RDM ] button for 1 second or longer. DISC and RDM light in the display and disc random play starts. 2. To cancel disc random play, press and hold the [ RDM ] button again. DISC and RDM go off from the display and normal play resumes from the current track.
2. Press the [ a ] or [ d ] button to automatically seek a station. Press the [ d ] button to automatically tune up the frequency band to the next available TV station; press the [ a ] button to automatically tune down.
There are 2 ways available: Quick tuning and step tuning. When you are in the step tuning mode, the frequency changes one step at a time. In the quick tuning mode, you can quickly tune the desired frequency. 1. Press the [ BAND ] button and select the desired band (TV1 or TV2).
If MANU is not lit in the display, press and hold the [ BAND ] button for 1 second or longer. MANU lights in the display and manual tuning is now available.
A total of 12 TV stations can be stored (6-TV1 and 6-TV2). This allows you to select your favorite TV stations and store them in memory for later recall. 1. Press the [ BAND ] button and select the desired TV band (TV1 or TV2). 2. To recall a stored TV station, press the desired [ DIRECT ] button to select that station.
Press and hold one of the [ DIRECT ] buttons for 2 seconds or longer to store the current station into preset memory.

Setting the TV diver

You can change the reception setting for the TV antenna connected to the TV tuner. 1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button to select TV DIVER. 3. Press the [ w ] button to set to DIVR ON or press the [ z ] button to set to DIVR OFF. G DIVR ON : Sets reception emphasizing the visual. G DIVR OFF : Sets the diver setting to OFF. 4. Press the [ T ] button to return to the previous mode.
1. Select the desired station with seek tuning, manual tuning or preset tuning. 2. Press and hold one of [ DIRECT ] buttons for 2 seconds or longer to store the current station into preset memory.

Auto store selects 6 TV stations automatically and stores each one into preset memory. If there are not 6 stations with good reception, stations previously stored in memory remain and only the strong stations are stored into memory. 1. Press the [ BAND ] button and select the desired TV band (TV1 or TV2). 2. Press and hold the [ P/A ] button for 2 seconds or longer. The stations with good reception are stored automatically to the preset channels.
Preset scan allows the user to view each preset position before it automatically advances to the next preset. This function is useful for searching for a desired TV station in memory. 1. Press the [ P/A ] button. 2. When the desired station is found, press the [P/A] button again to remain tuned to that station.
Do not press and hold the [ P/A ] button for 2 seconds or longer. Doing so will trigger the auto store function and start storing stations into memory.

Setting the TV area

When you select the TV area (TV reception area), the TV tuner area setting changes. 1. Press and hold the [ T ] button for 1 second or longer to switch to the adjustment selection display. 2. Press the [ a ] or [ d ] button to select TV AREA. 3. Press the [ s ] button. 4. Press the [ w ] or [ z ] button to select the reception area. 5. Press the [ s ] button. 6. Press the [ T ] button to return to the previous mode.
Problem Power does not turn on. (No sound is produced.) Fuse is blown.
Solution Replace with a fuse of the same amperage. If the fuse blows again, consult your store of purchase. Consult your store of purchase. Eject the compact disc before loading the new one. Clean the compact disc with a soft cloth. Replace with a compact disc with no scratches.
Incorrect wiring. Compact disc cannot be loaded. Another compact disc is already loaded.

Sound skips or is noisy.

Compact disc is dirty. Compact disc is heavily scratched or warped.
Sound is bad directly after power is turned on. Nothing happens when buttons are pressed. display is not accurate.
Water droplets may form on the internal lens when the car is parked in a humid place. Microprocessor has malfunctioned due to noise, etc.
Let dry for about 1 hour with the power on.
Turn off the power, then open the [ DOOR ] by up the [ HOOK ]. Press the reset button for about 2 seconds with a thin rod. Reset Button

8. IN CASE OF DIFFICULTY

9. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed. Take the measures described below to eliminate the problem. Error Display ERROR 2 Cause A CD is caught inside the CD deck and is not ejected. Measure This is a failure of CD decks mechanism and consult your store of purchase. Replace with a non-scratched, non-warped-disc. Eject the disc then reload it properly.

ERROR 3 ERROR 6

A CD cannot be played due to scratches, etc. A CD is loaded upside-down inside the CD deck and does not play. A CD inside the CD changer is not loaded.

ERROR 2

CD changer
This is a failure of CD changers mechanism and consult your store of purchase. Replace with a non-scratched, non-warped disc.

ERROR 3

A CD inside the CD changer cannot be played due to scratches, etc. A CD inside the CD changer cannot be played because it is loaded upside-down. Displayed when the temperature in the MD changer is too high and playback has been stopped automatically. An MD inside the MD changer is not loaded.

ERROR 6

Eject the disc then reload it properly.

ERROR H

Lower the surrounding temperature and wait for a while to cool off MD changer. This is a failure of MD changers mechanism and consult your store of purchase. Replace with a non-scratched, non-warped disc.

MD changer

An MD inside the MD changer cannot be played due to scratches, etc. An MD inside the MD changer cannot be played because it is loaded upside-down. Displayed when a non-recorded MD is loaded in the MD changer.
Load a pre-recorded MD in the MD changer.
If an error display other than the ones described above appears, press the reset button. If the problem persists, turn off the power and consult your store of purchase.

FM Tuner

Frequency Range : U.S.A : 87.9 MHz to 107.9 MHz Europe : 87.5 MHz to 108.0 MHz Australia : 87.0 MHz to 108.0 MHz Usable Sensitivity : 9 dBf 50dB Quieting Sensitivity : 15 dBf Alternate Channel Selectivity : 70 dB Stereo Separation (1 kHz) : 35 dB Frequency Response (3 dB) : 30 Hz to 15 kHz
Maximum Power Output : 208 W (52 W 4 ch) Continuous Average Power Output : 17 W 4, into 4 , 20 Hz to 20 kHz, 1%THD Bass Control Action (60 Hz) : 15 dB Treble Control Action (10 kHz) : 12 dB Line Output Level (CD 1 kHz) : 2 V

General

Power Supply Voltage : 14.4 V DC (10.8 to 15.6 V allowable), negative ground Current Consumption : Less than 15 A Speaker Impedance : 4 (4 to 8 allowable) Weight / Source unit : 3.52 lb. (1.6 kg) Dimensions / Source unit : 7" (Width) 2" (Height) 6" (Depth) [178 (W) 50 (H) 152 (D) mm] Escutcheon section : 9" (Width) 4" (Height) 1-1/2" (Depth) [232 (W) 95 (H) 28 (D) mm]

AM Tuner

Frequency Range : U.S.A : 530 kHz to 1710 kHz Europe : 531 kHz to 1602 kHz Australia : 531 kHz to 1629 kHz Usable Sensitivity : 25 V

CD Player

System : Compact disc digital audio system Usable Discs : Compact disc Frequency Response (1 dB) : 10 Hz to 20 kHz Signal to Noise Ratio (1 kHz) : 100 dB Dynamic Range (1 kHz) : 95 dB Harmonic Distortion : 0.01%
Specifications and design are subject to change without notice for further improvement.

10. SPECIFICATIONS

Owners manual Mode demploi Manual de instrucciones Istruzioni per luso

Contents

1. FEATURES.. 2 2. CONTROLS... 3 3. PRECAUTIONS... 4 Handling Compact Discs.. 5 4. NOMENCLATURE... 6 Names of the Buttons and their Functions.. 6 Major Button Operations when External Equipment is Connected to This Unit.. 7 Display Items... 8 LCD Screen.. 8 5. WIRED REMOTE CONTROL UNIT OPERATIONS. 9 6. OPERATIONS... 10 Basic Operations.. 10 Radio Operations... 12 CD Operations... 13 Operations Common to Each Mode.. 14 7. OPERATIONS OF ACCESSORIES.. 16 CD/MD Changer Operations.. 16 TV Operations... 17 8. IN CASE OF DIFFICULTY.. 19 9. ERROR DISPLAYS... 20 10. SPECIFICATIONS.. 21
AM/FM MARINE CD PLAYER RADIO AM/FM-LECTEUR CD MARIN REPRODUCTOR DE DISCOS COMPACTOS NUTICO CON RADIO DE AM/FM RADIO AM/FM CON LETTORE CD PER USO MARITTIMO

1. FEATURES

G G G G G G G G G G G G G Exclusive Marinized Front Panel Water Sealed Media Access Door Conformally Coated Microprocessor Input for Marine Wired Remote Control 2 Band Parametric EQ (Z-Enhancer Plus) White Positive LCD CeNET Control of Optional: TV Tuner, 6 Disc CD Changer, Sirius Satellite Radio Receiver Subwoofer Level Control 4 Channel RCA Line Level Output 208 Watt (52W 4) Tuner with 18 FM/ 6 AM Presets Magna Bass EX Built in Low Pass Crossovers (off/50Hz/80Hz/120Hz)

Clarion Co., Ltd.

2003/3 (DC)
All Rights Reserved. Copyright 2003: Clarion Co., Ltd. Printed in China / Imprim en Chine / Impreso en China / Stampato in Cina

PE-2588B 280-7867-00

280-7867-00/XMD3_cover

2/20/03, 3:48 PM

English
Thank you for purchasing this Clarion product. Please read this owners manual in its entirety before operating this equipment. After reading this manual, be sure to keep it in a handy place (e.g., glove compartment). Check the contents of the enclosed warranty card and keep it carefully with this manual. This manual includes the operating procedures of the CD changer, MD changer, AUX, and TV tuner connected via the CeNET cable. The CD changer, MD changer and TV tuner have their own manuals, but no explanations for operating them are described.
2. CONTROLS/COMMANDES/CONTROLES/CONTROLLI
Source unit / Appareil pilote / Unidad fuente / Unit sorgente
[RPT] [SCN] [PWR] [HOOK] [RDM] [DN], [UP]

3. PRECAUTIONS

1. When it is very cold in the boat and the unit is used soon after switching on the heater, the disc and the optical components may become fogged and not operate properly. Wipe fogged discs with a soft cloth. Fogged optical components will naturally return to normal when the unit is left for about one hour after which it will operate normally. 2. When the boat is traveling in the rough seas the sound may skip as a result of intense vibrations and shock. 3. This unit uses a precision mechanism. Even in the event that trouble arises, never open the case, disassemble the unit, or lubricate the rotating parts.
[DOOR] [P/A] [D] [M] [T] [Z+] [ISR]

[a], [d]

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to consult the dealer or an experienced radio/TV technician for help.

CAUTION

USE OF CONTROLS, ADJUSTMENTS, OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN, MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THE COMPACT DISC PLAYER and MINI DISC PLAYER SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE MANUFACTURER FOR COMPLIANCE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT.
INFORMATION FOR USERS: CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTURER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.

[w], [z] [A-M]

[BAND]

[DIRECT]

With the [DOOR](door) opened / Avec le volet [DOOR] ouvert / Con la puerta [DOOR] abierta / Con [DOOR] (sportello) aperto

[RESET] [CD SLOT] [Q]

Bottom View of Source Unit
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter. Remarque: Veuillez dplier cette page et vous rfrer aux schmas quand vous lisez chaque chapitre. Nota: Cuando lea los captulos, despliegue esta pgina y consulte los diagramas. Nota: Assicurarsi di aprire questa pagina e fare riferimento a questi diagrammi quando si legge ciascun capitolo.