Untertitel Scr Saver Letzter Speicher

Diskette Men

Lautsprechereinstellseite Abwrtsmischung

LT/RT Stereo

Sperrfunktion
Dolby Digital Einstellung Dynamisch

Kennwort Grundeinst.

05-AR 773 DVD_D.indd 25
Figure 1: Remote Control 1 II PLAY/PAUSE: a) Radio Mode: PTY selection of the program type. b) CD/MP3/DVD mode: Starting playback, stopping picture/track. 2 STOP: Stop play. 3 ANGLE/ : To select the viewing angle. 4 MO/ST/ : a) Radio Mode: Stereo/Mono switching. b) CD/DVD Mode: To change the Audio settings (depending on the DVD). 5 EQ/LOUD: Radio Mode: - Press briey: Selecting equaliser settings. - Press longer: Switching the LOUDNESS function on and off. 6 CLK: - Press briey: Showing/hiding the time. - Press longer: Setting the time. 7 I: To jump to the next chapter or song. 8 ENTER: Conrming the input. 9 Cursor buttons: a) Radio Mode: - Press briey: Manual station search. - Press longer: Automatic station search. b) MP3/DVD mode: Navigation in screen menu / For selecting the folders or MP3 tacks. 10 I: To return to the previous chapter or song. 11 Numerical buttons: a) Radio Mode: - Press briey (0-6): Station selection. - Press longer (0-6): Station storage. b) CD/MP3/DVD mode: For direct selection of chapter or song number. c) Bluetooth Mode: Entering the Telephone Number. 12 9/AF: Press longer: Switching on and off an alternative frequency. 0/TA: Press longer: Turning pre-switching for trafc announcements on and off. 13 +10: for selecting the chapters/tracks above 9. Pressing again increases by a further 10. 14 GOTO: For direct accessing of a section on the CD/DVD. 15 SETUP: To start the setup menu.
16 SEL: Radio Mode: - Press briey: Select sound/picture mode. - Press longer: REG, PI, AF function selection. 17 VOL +/-: To increase/reduce the volume. 18 A/PS: Radio Mode: - Press briey: Scan function of the stored radio stations. - Press longer: Automatic station storage. TITLE/PBC: a) To show the title menu of the DVD (depending on the DVD). b) To show the Playback-Control for VCD. 19 : Fast reverse. 20 BAND/OSD: a) Radio Mode: Switching the 3 FM and 2 MW levels. b) CD/MP3/DVD mode: Alternating the time displays. 21 LO/DX/ : a) Radio Mode: LOCAL/DX function. b) DVD Mode: To show/hide subtitles (depending on the DVD). 22 : Fast forward. 23 MENU/ : - Press briey: To display the main menu of the DVD/VCD. - Press longer: Switching the subwoofer on and off. 24 PAIR/ : Bluetooth Mode: - Press briey: Re-establishing a connection and dialling a telephone number that you have entered. - Press longer: Registering devices with one another and calling up the Bluetooth menu. 25 REDAIL/ : Bluetooth Mode: - Press briey: Rejecting a Call. - Press longer: Redialling. 26 : Changing the viewing angle of the operating unit. 27 /MODE: - Press briey: Operating mode selection (CD/DVD, AUX IN, Radio etc.). - Press longer: To activate standby mode. MUTE: To switch of the sound.

Figure 2: Control Panel - see Operation.
05-AR 773 DVD_GB.indd Abs1:26

19.10.2007 14:14:39 Uhr

Road Safety Safety Information
Read the operating instructions carefully before putting the appliance into operation and keep the instructions including the warranty, the receipt and, if possible, the box with the internal packing. If you give this device to other people, please also pass on the operating instructions. Use the device only for the intended purpose. The device should be installed in such a way that existing ventilation holes are not covered. Never open the housing of the device. Incorrect repairs can constitute a considerable risk for the user. If the device is damaged it should not be used, but repaired by a specialist. Road safety is of paramount importance. You should therefore use your car radio at all times in such a way that you are able to cope with the current trafc situation. Please remember that at a speed of 30 mph (50 kph) you travel 15 yards (14 metres) in one second. We advise you not to operate the radio in critical situations. It must be possible to hear the sirens of police and re brigade vehicles etc. from inside the vehicle in good time. When driving you should therefore not turn the radio volume up excessively. For safety reasons a lock connected to the handbrake of the vehicle prevents certain functions of the device from operating when the vehicle is moving. In order to be able to use these functions please stop in a safe place and put on the handbrake. Please note that it is not permitted to operate the DVD player when the vehicle is moving or if the engine is running! In order to prevent road accidents you should install the device in such a way that it does not cause an obstruction when you turn the steering wheel or move the gear lever etc. Similarly, safety equipment such as airbags and the drivers view of the road must not be obstructed. Under no circumstances should any additional monitor that is connected be installed in such a way that it can be seen by the driver when the vehicle is moving!
These symbols may be found on the machine and are intended to indicate the following: The symbol with an exclamation mark should advise the user of important operation or maintenance instructions in the accompanying documentation. Devices bearing this symbol work with a class 1 laser for tracing the CD/DVD. The built-in safety switches should prevent the user being exposed to dangerous laser light, which is invisible to the human eye, when the CD compartment is opened Under no circumstances should these safety switches be bypassed or manipulated, as this could result in a danger of exposure to the laser light. Children and Frail Individuals In order to ensure your childrens safety, please keep all packaging (plastic bags, boxes, polystyrene etc.) out of their reach. Caution! Do not allow small children to play with the foil as there is a danger of suffocation! Symbols in these Instructions for Use Important information for your safety is specially marked. It is essential to comply with these instructions in order to avoid accidents and prevent damage to the machine: WARNING: This warns you of dangers to your health and indicates possible injury risks. CAUTION: This refers to possible hazards to the machine or other objects.

NOTE: The signals from the remote control are transmitted to the device by infrared light. You should therefore ensure that the device is not in direct sunlight. This might make transmission of the signals from the remote control to the device impossible.
Effective range of the remote control Point the remote control at the remote control sensor on the right next to the display on the front of the device. The distance between remote control and sensor should not exceed 5m. The angle of the remote control to the remote control sensor to right, left, top and bottom should not exceed 30.
The lifetime of the enclosed battery may be shortened because of storage.
NOTE: The lithium cell in the battery compartment of the remote control has been secured for transport with a foil. Before initial use please remove this foil so that the remote control is ready for operation.
The battery of the remote control is a long-life lithium cell. If the range of the remote control is reduced during use, please proceed as follows: Open the battery compartment on the back of the remote control.
Operation (Illustration 2: Control Panel)
NOTE: Some keys are to be found both on the device itself and on the remote control. Keys with the same designation have the same function.
1. BAND/ button In radio mode: Press the BAND/ button briey to switch between the 3 FM bands and the 2 MW (medium wave) bands. The designation of the corresponding level - FM1, FM2, FM3, MW1, MW2 - is shown in the TFT. In Bluetooth Mode: Press the button to end the telephone call or reject an incoming telephone call. 2. REL Button Press the REL button to remove the front operating panel.
Replace the cell by a battery of the same type. Ensure correct polarity.
3. VOL Multifunction Button (Volume) In the standard playback mode the multifunction button is used for adjusting the volume. If the SEL button is pressed beforehand, changes can be made in the menus, e.g. sound mode. 4. RESET Button Due to voltage uctuations in your vehicle electrical system it is possible that the control processor of your radio has hung up. This is not a fault in the device! Press this button with a pointed object to restart it (reset).
Then close the battery lid.

NOTE: If you do not insert a CD/DVD the operating unit only returns to the normal position after a certain time, or you can press the button again.
CAUTION: With this device it is possible to play back only 12 cm discs! 11. SEL Button (Select) a) Press the SEL button briey to access the sound/picture mode selection menu. BUZZER appears in the display to set the conrmation tone. By repeatedly pressing the SEL button you can now select the individual menu items such as BUZZER (conrmation tone), BLUETOOTH, BASS, TREBLE, BALANCE and FADE, BG COLOUR (background colour), COLOUR*, BRIGHT* (brightness), CONTRAST* and VOLUME. The settings of the individual menu items are changed by turning the multifunction button VOL (3). (*only in DVD mode) b) Press the SEL button for a longer time to access the selection menu: REG ON / REG OFF PI MUTE / PI SOUND AF OFF / AF ON
Repeatedly pressing of the SEL button now brings up the individual menu items. The settings of the individual menu items are changed by turning the multifunction button VOL.
05-AR 773 DVD_GB.indd Abs1:32

19.10.2007 14:14:43 Uhr

REG Function At certain times some stations divide up their programmes into regional programmes with varying content. REG ON: The message REG ON appears in the display for a few seconds.
The status of the AF function is shown by an AF symbol in the display. If the AF symbol appears in the display, the AF function is switched on and RDS transmission data is being received. If the AF symbol ashes in the display, the AF function is selected but no RDS signal can be received at the moment.
Button See section 6./12.
REG OFF: The programme identication (PI) of the regional programme is ignored during the search for an alternative frequency (AF) or a programme identication (PI). PI MUTE/PI SOUND (only for radio operation) If you are in an area where two programme identications (PI) overlap, you can select the option PI SOUND and PI MUTE for playback of the sound. Alternate switching of the programme identication should be avoided. PI SOUND: If switching nevertheless occurs the sound of another station is heard for less than one second. PI MUTE: The sound of another station is suppressed. AF (Alternative Frequencies) AF is a function that works with the help of RDS (Radio Data System) and can only be used with FM stations. The radio searches in the background for the best frequency reception of the station that has been tuned into. AF ON: If the AF function has been switched on, the radio continuously tests the signal strength of the AF frequency. The test interval for each AF frequency depends on the signal strength of the current station and varies from a few minutes in the case of a strong signal to a few seconds in the case of weak signals. Whenever the new AF frequency is stronger than the station that is currently tuned in, the radio switches to this frequency for a short time and the message NEW FREQUENCY is displayed for one to two seconds. As the mute time during the frequency change and the test time is very short, this is almost inaudible during the normal programme.

13. II-/CH 1-6 Button Radio Mode: Press repeatedly to select the 6 preset radio stations of the current FM or MW band. CD/DVD/USB Operation: Press the II-/CH 1-6 button to interrupt playback of the CD (pause function). Press this button again to cancel this function. 14. /MOD button (on/off button / operating mode) a) Press this button to switch the device on. WELCOME appears in the display. Keep this button pressed to switch the device off. SEE YOU appears in the display. b) Press this button to select the CD/DVD player, AUX IN, BT MUSIC, radio mode etc. 15. APS/DISP Button (Autostore - Automatic Station Storage) In radio mode: a) Memory function: Move the SEL button in the direction of APS for approximately 2 seconds to activate automatic station storage. The device searches within the current frequency band for the greatest signal strength until the search cycle is complete. The six strongest stations are then allocated to the corresponding storage locations. Then the station of the rst storage location (FM1) is set. b) Scan Function: If the SEL button is moved briey in the direction of APS, the radio briey plays all the preset stations of the frequency band.
NOTE: The scan function ends automatically at the rst storage location of frequency band FM1.
In DVD mode: Move the SEL button a short distance in the APS/DISP direction in order to turn the TFT monitor on the device off and on again.
The AF function can also be activated by keeping the TA/AF button (8) pressed down.
05-AR 773 DVD_GB.indd Abs1:33
The display capacity is limited. It is possible that in the double display mode some segments of the display are deleted. The function REG ON prevents the radio from switching to alternative frequencies which have a different regional programme content.
AF OFF: The function is switched off. The AF symbol in the display goes off.
16. USB Connexion This device has been developed in accordance with the latest technical developments in the USB eld. Unfortunately the large number of different types of USB storage media on offer today makes it impossible to guarantee full compatibility with all USB storage media. For this reason there may be problems in rare cases with playing back from USB storage media. This is not a malfunction of the device. If you would like to play back data contained on a USB stick, please insert the stick into the opening provided. You can use the supplied adapter cable for this. To play back the data on the stick, select the USB stick with the help of the MOD(E) button. The data is played back automatically. If you have problems with operation using the USB connexion, please use an appropriate adapter cable and proceed as described under AUX IN. 17. MIC (Microphone) 18. AUX IN socket To connect analogue replay devices. Use this jack to replay sound of other replay equipment such as DVD players, computers, etc. via the loudspeakers. 1. Please connect the external device with a 3.5 mm stereo jack plug to the AUX IN socket. 2. Press the MOD(E) button (11) to select the AUX IN connection. 3. You now hear the sound from the external device played back through the loudspeakers. 4. With the VOL multifunction button (3) you can change the volume. 5. For the remaining procedure please see the operating instructions of the external sound source. 19.

area) in order to re-establish the connection (BLUETOOTH CONNECTING appears in the TFT display).
NOTE: Press this button during a call in order to transfer it back to your mobile telephone. If you press the button again the call is transferred back to the car radio.
Setting the Time 6. CLK Button (Time) (on the remote control) a) Press the CLK button in order to bring up or hide the clock. b) To set the time keep the CLK button pressed down for approx. 3 seconds. The hours ash in the display. Carry out the settings with the help of the VOL multifunction button (3). Press the CLK button again. The minutes now ash. Carry out the settings with the help of the VOL multifunction button (3). Press the CLK button again to store.
NOTE: If RDS data is received the time is set automatically.
Using the Number Buttons Numerical buttons (11 on the remote control) as Station buttons (16) of preselected stations and as 1TOP-, 3 INT-, 4 RDM buttons during CD operation a) Radio Operation Pressing these buttons briey directly selects a preset radio station. If these buttons are pressed for more than one second, the station currently being listened to is stored under the selected station button. b) CD Operation Pressing briey directly selects the corresponding CD/MP3 track. Keep the corresponding button (1TOP, 3INT, 4RDM) pressed for approximately 3 seconds in order to switch the following functions on and off: Press the 1TOP button to jump to the rst track of the CD/MP3.
Adjust the volume of the external device to an appropriate level.
Button (Operating unit angle) You can change the viewing angle of the operating unit. Press the button up to four times in order to select the desired position. WARNING: Do not place your ngers behind the operating unit. There is a danger of injury if the operating unit returns to the normal position.
NOTE: No function during DVD operation.
Press the 2RPT button. The track currently being played is repeated. Press this button again to cancel this function. In the case of DVDs you can repeat the chapter, title or the entire DVD. Press the 3INT button. Each track on the CD is played for 6 seconds. Press this button again to stop searching. The currently selected track is played. During DVD operation a menu appears. Here you can use the , , , buttons (9 on the remote control) of the remote control to choose between 4 options. Conrm your selection with the ENTER button (8 on the remote control).

20. PAIR/ In Bluetooth mode: Press this button to accept an incoming telephone call. Keep the button pressed down to call up the Bluetooth menu. Keep the button pressed down to make the connection between the devices (BLUETOOTH PAIRING appears in the TFT display). Press the button briey after the connection between the devices has been interrupted (e.g. after leaving the reception
NOTE: No function during MP3 operation.
05-AR 773 DVD_GB.indd Abs1:34

19.10.2007 14:14:44 Uhr

Press the 4RDM button. The DVD, MP3/CD tracks are played at random. Press this button again to cancel this function. Button (21 on the remote control)

Radio Mode

Reception of this station data is shown in the display by the EON symbol. You can choose between the LOC(AL) and DX (DISTANCE) mode for local or long-distance trafc news. LOC(AL): This function prevents switching to an EON station whose signal is too weak. The radio does not switch to this station and the listener does not hear any interference. DX (DISTANCE) Mode: In this mode the EONTA circuitry tries to receive the EONTA information from any available transmitter and thus improve reception quality. DVD Operation: Press the button several times if you would like to activate or deactivate the subtitle function or if you want to choose a different subtitle language. The available subtitle languages depend on the DVD.
To switch of the sound. Operating mode selection (CD/DVD, AUX IN, Radio etc.). Next Menu. Switching the 3 FM and 2 MW levels. Press briey: Station selection. Press longer: Station storage. 6 Press briey: Setting the Radio Frequency. Press longer: Station Search for the Next Station.

Using the Touch Screen

In addition to operating the device by the buttons, the device itself and with the remote control, it is also possible to use the touch screen. Touch the TFT screen of the device lightly with one of your ngers. The respective main menu of the individual modes is displayed. Touch the buttons shown lightly in order to perform the functions. A brief overview is to be found in the following section: 5 To increase/reduce the volume. LOCAL/DX function. Next Menu. Redialling. Press briey: Selecting the Sound Mode. Press longer: REG, PI, AF function selection. 6 Calling up the Bluetooth Menu. 7 Previous Menu.

If no selection is made within approximately 10 seconds the touch screen menu disappears again.
05-AR 773 DVD_GB.indd Abs1:35
LOCAL/DX (EON) (only available during radio operation) Your radio can receive RDS EON data. The term EON signies the transmission of additional station information within a station chain, e.g. WDR. If a trafc announcement (TA) is made within a station chain, the radio switches from a station which does not transmit trafc announcements to one that does within the same station chain.
1 Press briey: Showing/hiding the time. Press longer: Setting the time. 2 PTY selection of the program type. 3 Press briey: Scan function of the stored radio stations. Press longer: Automatic station storage. 4 Registering Devices with One Another. 5 Stereo/Mono switching. 6 Switching on and off an alternative frequency. 7 Turning pre-switching for trafc announcements on and off. 8 Previous Menu. 9 Switching the subwoofer on and off. 10 Switching the LOUDNESS function on and off. 11 Selecting equaliser settings. AUX IN Mode
Switching the LOUDNESS function on and off. Selecting equaliser settings. Loading and Ejecting the CD/DVD. Registering Devices with One Another. Press briey: Showing/hiding the time. Press longer: Setting the time. Changing the viewing angle of the operating unit. Previous Menu. Turning pre-switching for trafc announcements on and off. Switching on and off an alternative frequency. Switching the subwoofer on and off.
BT MUSIC Mode (A2DP) In this mode it is possible to play back the music from a device that is Bluetooth-compatible and operate the connected device.
HINWEIS: In order to be able to use this mode the connected device must support the A2DP prole.
A2DP (Advanced Audio Distribution Prole) A Bluetooth prole that is required in order to transfer stereo music and audio les between playback devices and receiving devices without wires.
To switch of the sound. Operating mode selection (CD/DVD, AUX IN, Radio etc.). Next Menu. To increase/reduce the volume. Press briey: Selecting the Sound Mode. Press longer: REG, PI, AF function selection. 6 Calling up the Bluetooth Menu. 7 Redialling. Stop play. To switch of the sound. Operating mode selection (CD/DVD, AUX IN, Radio etc.). Next Menu. To increase/reduce the volume. Press briey: Selecting the Sound Mode. Press longer: REG, PI, AF function selection. 7 Jump to the previous song. 8 Jump to the next song. 9 Start playback, stop the song.
05-AR 773 DVD_GB.indd Abs1:36

19.10.2007 14:14:45 Uhr

Registering Devices Before you can telephone via the car radio the devices have to be registered with one another. 1. Unless you have already done so, activate the Bluetooth function in the SEL menu (BLUETOOTH ON). 2. Hold the PAIR/ button (20) down (the symbol ashes and BLUETOOTH PAIRING appears in the display). 3. Register the car radio in your mobile telephone as described in the operating instructions for your mobile telephone. The device designation BC-HF-V01 appears as a choice in your mobile telephone. 4. Now enter the password 8888 in your mobile telephone. The car radio is now registered in your mobile telephone. 5. Once the registration has been successfully performed, appears in the display of the car radio together with the name of the mobile telephone.
Selecting the telephone number entered. Hold down to enter the hash. Hold down to enter the asterisk. Hold down to delete a telephone number that you have entered incorrectly. 5 For entering the telephone number. 6 Previous Menu.
05-AR 773 DVD_GB.indd Abs1:38

19.10.2007 14:14:46 Uhr

If registration was not successful, appears in the display of the car radio. Depending on the mobile telephone manufacturer, it is necessary to carry out the registration (PAIRING) again in order to register your mobile telephone in the car radio. Bluetooth compatibility cannot be guaranteed for mobile telephones that come onto the market in the future. In order to guarantee an optimum connection, please ensure that the battery of your mobile telephone is fully charged. Some makes of mobile telephone have an energy-saving mode. Please deactivate the energy-saving mode, as you may otherwise have problems when telephoning via Bluetooth. In order to be able to conduct an incoming or outgoing telephone call Bluetooth has to remain activated in your mobile telephone. Please consult the operating instructions for your mobile telephone. Please ensure that you speak in the direction of the built-in microphone. The connection of an external microphone is not possible.
NOTE: If you would like to redial the last number you can also press the button on the touch screen.

To end the call press either the button on the touch screen, the REDIAL/ button (25) on the remote control or the BAND/ button (1) on the device. Incoming Calls In the case of incoming calls a ringing tone is heard from the loudspeakers, and if the caller has a CLIP Calling Line Identication Presentation-capable telephone, the callers number appears in the display of the car radio. Otherwise CALL INCOMING appears in the display. 1. To accept an incoming call, press the PAIR/ button (20) to conrm. You will now hear the caller through the loudspeakers of your car. 2. To terminate the call please press the BAND/ button (1).
Outgoing Calls button (20/24) held down to call up 1. Keep the PAIR/ the Bluetooth menu. 2. In order to enter the desired telephone number please use either the touch screen or the number buttons on the remote control.
You can transfer the call back to your mobile telephone. In order to do so, keep the PAIR/ button (20) pressed. If this button is held down again, the call is transferred back to the car radio. In order to reject an incoming call press the BAND/ button (1).

About the DVD-Player

With this DVD-Player you can play a vast variety of DVD-formats Technical data. However, you must be aware that in many cases DVDs are encrypted with a so-called Regional Code. This species for which region in the world the DVD is intended. As an example, the DVDs marked with regional code 1 are intended for the USA and Canada. DVDs with regional code 2 are for use in Europe.
If you have entered one or more gures incorrectly you can delete them by repeatedly holding down the button or the cursor button on the remote control. 3. To call up the desired number, press the button in the touch screen menu. The words DIALING OUT appear in the display together with the telephone number. 4. To terminate the call please press the BAND/ button (1).
In order to call the telephone number you have entered you can also press the PAIR/ button (20). In order to end a call you can also press the button on the touch screen or the REDIAL/ button (25) on the remote control.
NOTE: With your DVD-Player you can only play DVDs with regional code 2. There are both lots of burning and compressing methods as well as high quality differences in (burned) CDs/ DVDs. Moreover, the music industry has not yet agreed on a xed standard for copy protection. This may, in very isolated cases, result in problems when relaying CDs, DVDs and MP3 CDs. This is no malfunction of the player.
Furthermore, there may be isolated problems when playing CDs or DVDs which were created on a PC (e.g. holiday photographs). In case of problems check the settings of the DVD writing program on your computer. You should in particular make sure that the DVD has been nalized. For further information on this matter please refer to the operating manual of your recorder. Input Not Possible If a function or input selected by you is not possible, the adjacent symbol is shown on the screen.

Fault Symptoms The device does not work correctly (EJECT, LOAD, PLAY).

Troubleshooting

Before going through the checklist please make all the connections rst. If you still have questions after going through the checklist, please consult your local customer service representative. Cause The transport screws have not been removed. The CD is inserted the wrong way round. There is no CD inserted. A USB storage medium is connected to the USB port. The CD does not The volume control is play back after being set too low. The device has inserted into the not been correctly device. connected. CD works intermittently The surface of the road (dropouts). is uneven. The device is not rmly installed. Fault Symptoms CDs are drawn only half way into the CD tray. NO DISC is shown in the display. CD cannot be selected using the MOD(E) button. Solution Remove the transport screws. Insert the CD right way round. Insert a CD. Remove the USB storage medium. Turn up the volume. Check the +12V and earth connection. Wait until the road becomes smoother before playing the CD. Install the device rmly. Ensure that the rear attachment is used if the vehicle does not have any suitable retainer for the rear section of the device. Try another CD. If this works correctly, the rst CD is probably damaged. Clean the CD. Please note that a maximum inclination of 20 degrees should not be exceeded! Turn the ignition key to ON or ACC. Replace the fuse by another 5 A /0,5 A fuse. Please contact your car workshop or a vehicle specialist for connection adapters may specically for your model.
Cause The microcomputer has been interfered with by electromagnetic elds. The device cannot be The control processor operated, but hangs of the device may up. have been blocked by overvoltage or undervoltage in the vehicle electrical system. No radio reception. The antenna cable is not connected.
Solution Remove the CD and reinsert it. Switch the device off and on again. Press the RESET button.

Poor radio reception.

In automatic search mode the radio does not stop at a transmitting station.

Insert the antenna cable rmly into the antenna socket of the device. It is possible that your Please contact your vehicle has a special car workshop or a antenna (phantomvehicle specialist. (For powered antenna.) other manufacturers there are specic phantom power supply adapters and voltage adapters available.) The transmission Tune in to a radio signals are too weak. station manually.

The CD is damaged.

No function.
The CD is dirty. The device may have been installed in the vehicle at the wrong angle. The ignition is switched off. One or more fuses have blown. Incorrect connection (each car manufacturer wires the ISO connection in the vehicle differently).
Device cannot be switched on or off via the ignition.
05-AR 773 DVD_GB.indd Abs1:44

19.10.2007 14:14:52 Uhr

Handling a CD
Cleaning the CD Before playing a CD, wipe it off with a clean, dust-free cleaning cloth. Pull out the CD in the direction of the arrow. CAUTION: Do not use any solvents such as petrol or thinning agents. Commercially available cleaning substances or antistatic sprays will damage the device. Inserting the CD If the CD is inserted with the printed side facing downwards, the device may be damaged. Always insert the CD with the label facing upwards. CAUTION: If there is already a CD in the CD slit, do not try to insert a second CD. This may damage the device. Touching the CD

Guarantee

The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt). During the life of the guarantee any fault of the device or its accessories ascribable to material or manufacturing defects will be eliminated free of charge by repairing or, at our discretion, by replacing it. The guarantee services do not entail an extension of the life of the guarantee nor do they give rise to any right to a new guarantee!
If you wish to make a claim under the guarantee please return the entire machine in the original packaging to your dealer together with the receipt. Defects to consumables or parts subject to wearing as well as cleaning, maintenance or the replacement of said parts are not covered by the guarantee and hence are to be paid! The guarantee lapses in case of unauthorized tampering.