05-AR 773 DVD_GB.indd Abs1:27

19.10.2007 14:14:40 Uhr

Installation
Please install the car radio as shown below.
Nut Spring washer Plain washer Screw Mounting bracket Slide-in housing Threaded bolt
NOTE: Coution! Retaining screws during transport (please remove before installation) Extraction tool (spanner for dismantling) Screen cover Fan
CAUTION: Do not cover the fan!
USA/EURO switch (radio frequency switch for selecting between the USA and EUROPE frequency band)
First place the operating panel in position on the righthand side and then lock it into place on the left.
05-AR 773 DVD_GB.indd Abs1:28

Connection

Connect the device as shown in the diagram.

ISO connection

Yellow Antenna connection Fuse Ignition (B+) Red AUX (optional) RCA cable RCA cable / output rear (optional) Fuse/ lter box RCA cable / output front
Camera input rear Video input rear Audio input R (red) Audio input L (white) Subwoofer (grey) Video output 2 (yellow) Coaxial output (brown) R red
Constant current Yellow connection (B+) Earth (B-) Black

Automatic Blue antenna

L white RCA front right (red) Video output 1 (yellow) RCA front left (white) (Only about version at RCA output cable)

Loudspeaker, front left

White White/black

Grey Grey/black

Loudspeaker, front right

Loudspeaker, rear left

Green Green/black

Violet Violet/black

Loudspeaker, rear right
Note: The device should only be switched on after all cables have been connected. Please use loudspeakers with an impedance of 4 ohm. The loudspeaker cables must be unearthed. If a subwoofer is connected, an amplier is required. The earth connection cable (handbrake B-) must be connected in order for DVD pictures to be played back to the monitor. If the cable has not been correctly connected, the message PARKING BRAKE appears on the monitor. It is possible to use the integrated TFT screen as a monitor for an optional reversing camera (not supplied). Connect the (B+) 12V camera on rear connection to the reversing light of your vehicle and connect the camera to camera input on rear (yellow). After the vehicle is put into reverse gear the camera image appears on the monitor. For more detailed information please see the operating instructions for your reversing camera.

NOTE:

If there is no 12V supply to the (B+) 12V camera rear connection the picture from the camera is not displayed on the monitor.

05-AR 773 DVD_GB.indd Abs1:29

19.10.2007 14:14:41 Uhr

White Green
(B+) 12 V Camera rear (B-) Hand brake
Important Information for installing your carradio!
1. The screws (h) of the transport locking device should be removed before installation, as otherwise the CD cannot be inserted. 2. The device is designed for the minus pole of the battery, which must be connected to the body of the vehicle. Please check this before installation. 3. When installing/connecting your device please note that not every vehicle is equipped with an ISO connection. In this case we recommend the use of an ISO adapter specically designed for your vehicle. Adapters are available from car accessory shops and/or from your vehicle workshop. 4. Depending on the specic car type, different wiring connection of the Duration + wire (Constant current connection) are available. (However, this is necessary for storing the radio stations). In order to guarantee all functions, installation in line with these instructions is essential. In cases of doubt please contact an authorised car workshop. Due to the large number of vehicle types and manufacturers the correct conguration of the ISO plug cannot be guaranteed, even if the ISO plug connections t together mechanically. It may therefore be necessary to change the electricity connection or use adapters made specically for motor vehicles. When connected correctly, the radio can be switched on and off by means of the ignition. If the stored stations are lost the radio does not receive any Permanent + required for station storage. CAUTION: If the connection is made to Permanent + without ignition the car radio may be subjected to a load even with the ignition switched off. In the worst case this may result in the car battery becoming completely discharged. In the case of car radios with Bluetooth it is essential that the connection is made properly via the ignition. Otherwise there will be no correct separation of the radio connection between the car radio and the mobile telephone. 5. The angle of inclination when a car radio is installed must not exceed 20, as in the case of greater angles of inclination the function of the car radio (CD/DVD Player) can no longer be guaranteed. 6. Depending on the specic car type, interferences can be possibly arise during radio/CD/DVD operation. These interferences can avoided easily with an additional Interferences lter. Your car radio is originally prepared with an Interference Filter already. In these case, please contact your authorized car dealer.

Then close the battery lid.
5. TFT Display (liquid crystal display) 6./12. / Buttons a) In radio mode: Move the SEL button in the direction of or in order to set a radio station manually. Keep the SEL Taste pressed down in the or direction in order to start the search for a radio station.
If the remote control is not used for a prolonged period, remove the batteries in order to prevent battery acid leaking. CAUTION: Batteries are not to be disposed of together with domestic wastes. Dispose of the used batteries at the relevant collection bin or at your dealers. WARNING: Do not expose the batteries to high temperatures or direct sunlight. Never throw batteries into the re. There is a danger of explosion!
05-AR 773 DVD_GB.indd Abs1:31
b) In CD/DVD, USB mode: If you wish to jump forwards or backwards press the SEL button briey in the or direction. To wind through the tracks keep the SEL button pressed in the or direction for approximately 2 seconds. X2 appears in the display. Operating the SEL button again in the or direction for approximately 2 seconds increases the winding speed. Speeds of X2, X4, X8 and X16 are available. Press the II/CH 1-6 button (13) to return to normal playback.
then appears briey in the display. When PTY has been selected the radio starts searching for corresponding PTY information and stops when the PTY information has been found. If the programme type being searched for is not found, NO PTY appears in the display. If the PTY information being searched for no longer exists, the PTY function automatically switches to normal mode. 10. Button Press this button to insert and eject the CD/DVD. The operating unit swings downwards. Insert the CD/DVD with the labelled side facing upwards gently into the CD slot until the device draws in the CD/DVD automatically. The operating unit automatically swings back to the normal position. WARNING: Do not place your ngers behind the operating unit. There is a danger of injury when the operating unit returns to the normal position.
7. IR (Infrared) Sensor for the remote control 8. TA / AF Button a) TA Trafc Annonuncement (Priority for Trafc Information) The TA function is activated by pressing the TA/AF button briey. The TA symbol appears in the display. During radio operation in one FM frequency band the search for a trafc announcement station is started automatically (TA SEEK). If an FM station is being received which transmits the latest trafc announcements from time to time, the TP display lights up. When the TA function is switched on, the FM trafc announcements automatically interrupt CD operation (The word TRAFFIC appears in the display). The volume level is increased to the minimum value for the transmission of trafc announcements. After the trafc announcement has nished, the programme that was previously running is resumed. Interruption of the TA Function: If you would like to interrupt the current trafc announcement, press the TA/AF button briey. This does switch off the TA mode. b) AF (Alternative Frequencies) See point 14. 9. MU/PTY Button (Mute) a) Press the MU/PTY button to switch off the loudspeakers for a short period. The word MUTE ashes in the display. Press this button again to cancel the mute function. This function can also be cancelled by pressing the VOL multifunction button. b) Radio Operation: PTY Selection of the Programme Type Besides the station name, some FM stations also transmit information on the type of programme. This information can be displayed by your car radio. Examples of such types of programme are: SPORT NEWS POP CLASSICS With the PTY function you can specically select stations transmitting a particular type of programme. Keep the MU/PTY button pressed down for approx. 2 seconds to access the PTY menu. The message PTY SEEK

NOTE: If you do not insert a CD/DVD the operating unit only returns to the normal position after a certain time, or you can press the button again.
CAUTION: With this device it is possible to play back only 12 cm discs! 11. SEL Button (Select) a) Press the SEL button briey to access the sound/picture mode selection menu. BUZZER appears in the display to set the conrmation tone. By repeatedly pressing the SEL button you can now select the individual menu items such as BUZZER (conrmation tone), BLUETOOTH, BASS, TREBLE, BALANCE and FADE, BG COLOUR (background colour), COLOUR*, BRIGHT* (brightness), CONTRAST* and VOLUME. The settings of the individual menu items are changed by turning the multifunction button VOL (3). (*only in DVD mode) b) Press the SEL button for a longer time to access the selection menu: REG ON / REG OFF PI MUTE / PI SOUND AF OFF / AF ON
Repeatedly pressing of the SEL button now brings up the individual menu items. The settings of the individual menu items are changed by turning the multifunction button VOL.
05-AR 773 DVD_GB.indd Abs1:32

19.10.2007 14:14:43 Uhr

REG Function At certain times some stations divide up their programmes into regional programmes with varying content. REG ON: The message REG ON appears in the display for a few seconds.
The status of the AF function is shown by an AF symbol in the display. If the AF symbol appears in the display, the AF function is switched on and RDS transmission data is being received. If the AF symbol ashes in the display, the AF function is selected but no RDS signal can be received at the moment.
Button See section 6./12.
REG OFF: The programme identication (PI) of the regional programme is ignored during the search for an alternative frequency (AF) or a programme identication (PI). PI MUTE/PI SOUND (only for radio operation) If you are in an area where two programme identications (PI) overlap, you can select the option PI SOUND and PI MUTE for playback of the sound. Alternate switching of the programme identication should be avoided. PI SOUND: If switching nevertheless occurs the sound of another station is heard for less than one second. PI MUTE: The sound of another station is suppressed. AF (Alternative Frequencies) AF is a function that works with the help of RDS (Radio Data System) and can only be used with FM stations. The radio searches in the background for the best frequency reception of the station that has been tuned into. AF ON: If the AF function has been switched on, the radio continuously tests the signal strength of the AF frequency. The test interval for each AF frequency depends on the signal strength of the current station and varies from a few minutes in the case of a strong signal to a few seconds in the case of weak signals. Whenever the new AF frequency is stronger than the station that is currently tuned in, the radio switches to this frequency for a short time and the message NEW FREQUENCY is displayed for one to two seconds. As the mute time during the frequency change and the test time is very short, this is almost inaudible during the normal programme.

area) in order to re-establish the connection (BLUETOOTH CONNECTING appears in the TFT display).
NOTE: Press this button during a call in order to transfer it back to your mobile telephone. If you press the button again the call is transferred back to the car radio.
Setting the Time 6. CLK Button (Time) (on the remote control) a) Press the CLK button in order to bring up or hide the clock. b) To set the time keep the CLK button pressed down for approx. 3 seconds. The hours ash in the display. Carry out the settings with the help of the VOL multifunction button (3). Press the CLK button again. The minutes now ash. Carry out the settings with the help of the VOL multifunction button (3). Press the CLK button again to store.
NOTE: If RDS data is received the time is set automatically.
Using the Number Buttons Numerical buttons (11 on the remote control) as Station buttons (16) of preselected stations and as 1TOP-, 3 INT-, 4 RDM buttons during CD operation a) Radio Operation Pressing these buttons briey directly selects a preset radio station. If these buttons are pressed for more than one second, the station currently being listened to is stored under the selected station button. b) CD Operation Pressing briey directly selects the corresponding CD/MP3 track. Keep the corresponding button (1TOP, 3INT, 4RDM) pressed for approximately 3 seconds in order to switch the following functions on and off: Press the 1TOP button to jump to the rst track of the CD/MP3.
Adjust the volume of the external device to an appropriate level.
Button (Operating unit angle) You can change the viewing angle of the operating unit. Press the button up to four times in order to select the desired position. WARNING: Do not place your ngers behind the operating unit. There is a danger of injury if the operating unit returns to the normal position.
NOTE: No function during DVD operation.
Press the 2RPT button. The track currently being played is repeated. Press this button again to cancel this function. In the case of DVDs you can repeat the chapter, title or the entire DVD. Press the 3INT button. Each track on the CD is played for 6 seconds. Press this button again to stop searching. The currently selected track is played. During DVD operation a menu appears. Here you can use the , , , buttons (9 on the remote control) of the remote control to choose between 4 options. Conrm your selection with the ENTER button (8 on the remote control).
20. PAIR/ In Bluetooth mode: Press this button to accept an incoming telephone call. Keep the button pressed down to call up the Bluetooth menu. Keep the button pressed down to make the connection between the devices (BLUETOOTH PAIRING appears in the TFT display). Press the button briey after the connection between the devices has been interrupted (e.g. after leaving the reception

05-AR 773 DVD_GB.indd Abs1:35
LOCAL/DX (EON) (only available during radio operation) Your radio can receive RDS EON data. The term EON signies the transmission of additional station information within a station chain, e.g. WDR. If a trafc announcement (TA) is made within a station chain, the radio switches from a station which does not transmit trafc announcements to one that does within the same station chain.
1 Press briey: Showing/hiding the time. Press longer: Setting the time. 2 PTY selection of the program type. 3 Press briey: Scan function of the stored radio stations. Press longer: Automatic station storage. 4 Registering Devices with One Another. 5 Stereo/Mono switching. 6 Switching on and off an alternative frequency. 7 Turning pre-switching for trafc announcements on and off. 8 Previous Menu. 9 Switching the subwoofer on and off. 10 Switching the LOUDNESS function on and off. 11 Selecting equaliser settings. AUX IN Mode
Switching the LOUDNESS function on and off. Selecting equaliser settings. Loading and Ejecting the CD/DVD. Registering Devices with One Another. Press briey: Showing/hiding the time. Press longer: Setting the time. Changing the viewing angle of the operating unit. Previous Menu. Turning pre-switching for trafc announcements on and off. Switching on and off an alternative frequency. Switching the subwoofer on and off.
BT MUSIC Mode (A2DP) In this mode it is possible to play back the music from a device that is Bluetooth-compatible and operate the connected device.
HINWEIS: In order to be able to use this mode the connected device must support the A2DP prole.
A2DP (Advanced Audio Distribution Prole) A Bluetooth prole that is required in order to transfer stereo music and audio les between playback devices and receiving devices without wires.
To switch of the sound. Operating mode selection (CD/DVD, AUX IN, Radio etc.). Next Menu. To increase/reduce the volume. Press briey: Selecting the Sound Mode. Press longer: REG, PI, AF function selection. 6 Calling up the Bluetooth Menu. 7 Redialling. Stop play. To switch of the sound. Operating mode selection (CD/DVD, AUX IN, Radio etc.). Next Menu. To increase/reduce the volume. Press briey: Selecting the Sound Mode. Press longer: REG, PI, AF function selection. 7 Jump to the previous song. 8 Jump to the next song. 9 Start playback, stop the song.
05-AR 773 DVD_GB.indd Abs1:36

19.10.2007 14:14:45 Uhr

Switching the LOUDNESS function on and off. Selecting equaliser settings. Registering Devices with One Another. Switching the subwoofer on and off. Switching on and off an alternative frequency. Turning pre-switching for trafc announcements on and off. Previous Menu. Calling up the Bluetooth Menu. Redialling.

1 In MP3 mode to select the folder or tracks. 2 Access selected folder/play track. 3 Previous Menu. Bluetooth Mode Depending on the mode you are currently using, call up the menu with the button and press it in order to call up the Bluetooth menu.
NOTE: The setting of the volume depends on the installation positions of the loudspeakers relative to the microphone and cannot therefore be specied in detail.
Registering Devices Before you can telephone via the car radio the devices have to be registered with one another. 1. Unless you have already done so, activate the Bluetooth function in the SEL menu (BLUETOOTH ON). 2. Hold the PAIR/ button (20) down (the symbol ashes and BLUETOOTH PAIRING appears in the display). 3. Register the car radio in your mobile telephone as described in the operating instructions for your mobile telephone. The device designation BC-HF-V01 appears as a choice in your mobile telephone. 4. Now enter the password 8888 in your mobile telephone. The car radio is now registered in your mobile telephone. 5. Once the registration has been successfully performed, appears in the display of the car radio together with the name of the mobile telephone.
Selecting the telephone number entered. Hold down to enter the hash. Hold down to enter the asterisk. Hold down to delete a telephone number that you have entered incorrectly. 5 For entering the telephone number. 6 Previous Menu.
05-AR 773 DVD_GB.indd Abs1:38

19.10.2007 14:14:46 Uhr

If registration was not successful, appears in the display of the car radio. Depending on the mobile telephone manufacturer, it is necessary to carry out the registration (PAIRING) again in order to register your mobile telephone in the car radio. Bluetooth compatibility cannot be guaranteed for mobile telephones that come onto the market in the future. In order to guarantee an optimum connection, please ensure that the battery of your mobile telephone is fully charged. Some makes of mobile telephone have an energy-saving mode. Please deactivate the energy-saving mode, as you may otherwise have problems when telephoning via Bluetooth. In order to be able to conduct an incoming or outgoing telephone call Bluetooth has to remain activated in your mobile telephone. Please consult the operating instructions for your mobile telephone. Please ensure that you speak in the direction of the built-in microphone. The connection of an external microphone is not possible.

Speaker setup

Downmix
If there is no Audio output, even though you connected the DVD-Player to an amplier, you will most likely have chosen an incorrect setting for the Audio output.

Captions

Change the characteristics of the speaker output: Some DVDs contain commentaries that accompany the lm, e.g. subtitles for the hard of hearing. On: The commentary is displayed. Off: No commentaries are displayed. LT/RT: Choose this setting if you want to play the DVD with the Pro Logic Dolby stereo effect. This produces a almost real 2-channel replay effect. Stereo: Choose this setting if you want to play a DVD, that has been produced in the 5.1-Audio format, as 2-channel stereo sound.
05-AR 773 DVD_GB.indd Abs1:41

19.10.2007 14:14:49 Uhr

The following options are available:

Digital setup

Dynamic Range

Subtitle language

The term Dynamic Range describes the ratio of quietest and loudest sound. If the dynamic range is very large, you will experience very quiet and very loud sounds. This may cause replay problems. Let us assume that you are watching a DVD in a relatively loud environment. You can now increase the volume to be able to hear also the very quiet passages, however with the disadvantage that loud passages will be unacceptably loud. In this case it would make sense to compress the dynamic range (i.e. reduce) and increase the output volume at the same time. FULL -2/8: The dynamic range is compressed slightly (2/8) to full (FULL). OFF: The dynamic range is not compressed at all (default).
Here you can select the preferred language for the subtitles accompanying the lm. Menu language
Here you can select the preferred language for the DVD menus. Parental (Child protection)

TV Type

Some DVD contain information concerning the target group. This method is comparable with the rating of cinema lms (Suitable only for persons of 12 years and over e.g.). Match the output of the DVD-Player to the colour transfer system of your replay device. The following options are available: PAL: A system commonly used in Europe. AUTO: Select this setting if your replay device is a multisystem unit. NTSC: A system primarily used in North America. If you have the child protection option activated a probably existing corresponding information is read from the DVD and compared with the value pre-set by you. If a DVD is intended for an older age group than the one pre-set by you, the DVD cannot be played. The following child protection options are available: Kid Saf: Suitable for children. G: Suitable for all age groups. PG: The presence of parents is recommended. Some scenes may be unsuitable for children. PG 13: The presence of parents is strictly recommended. Some scenes may be unsuitable for children under the age of 13. PGR: The presence of parents is strictly necessary. R: Young persons under the age of 17 may only view this lm in the presence of an adult. NC17: Children and juveniles under the age of 17 are not allowed to watch this lm. Adults: The lm must only be watched by adults. Off: The child lock is deactivated.

Audio language

Here you can select the preferred language for the audio output.
05-AR 773 DVD_GB.indd Abs1:42

19.10.2007 14:14:50 Uhr

Password General

Technical data

Supply voltage..DC 13,8 V Power consumption..10 A max. Power... 4 x 60 W PMPO Monitor...4,3 / 10,9 cm TFT Number of pixels.. 480 x 3 (RGB) x 272
In order to change the password, you must rst enter the current password. The master password is 1379.
Frequency range.87,5 MHz to 108,0 MHz Effective sensitivity..15 dB. I.F. frequency...10,7 MHz AM band Frequency range..522 kHz to 1620 kHz Effective sensitivity..40 dB I.F. frequency...450 kHz (Line-Out) Output... 2 CH & 4 CH Signal format...PAL/NTSC Video output..1,0 V (P-P) 75 Ohm CD player System.. MP3 Audio System Suitable CDs.. CD/CD-R/CD-RW/MP3/DVD/VCD Disks (12 cm discs) Playable bit rates..32 - 320 kBit/s Number of quantising bits... 1 bit. Frequency characteristics.. 20 Hz 20 kHz Signal-to-noise ratio..90 dB (JIS) Number of channels..2 stereo channels Housing dimensions.. 178 W x 50 H x 165 D Regionalcode.2 (= Europe, Greenland, South Africa, Egypt and Middle East, Japan) Bluetooth Standard.. V1.2 (Class II) Frequency band.. 2.4 GHz spectrum Range..approx. 3 metres (unobstructed)
If you forgot your password, you can deactivate the child protection system with this password.
Proceed as follows to change the password: 1. Enter the present password in the Old Password line with the Numeral buttons (Fig. 1/11) of the remote control. To prevent the password from being read by unauthorized persons only the characters XXXX will appear on the screen. 2. Enter the new password in the New Password line with the Numeral buttons of the remote control. 3. Conrm the new password by entering it again in the Conrm line. Conrm your entry with the ENTER button (Fig. 1/8). Default
Select the command Default/Reset if you want to reset the player to the factory implemented default settings. Any settings you have made will be lost.
05-AR 773 DVD_GB.indd Abs1:43

19.10.2007 14:14:51 Uhr

If you want to operate the DVD-Player with a child protection system, you must rst enter a password. This password safeguards the settings for the child protection system, so that it can only be changed by yourself.

FM band

This device has been tested according to all relevant current CE guidelines, such as electromagnetic compatibility and low voltage directives, and has been constructed in accordance with the latest safety regulations. Subject to technical changes without prior notice!
Fault Symptoms The device does not work correctly (EJECT, LOAD, PLAY).

Troubleshooting

Before going through the checklist please make all the connections rst. If you still have questions after going through the checklist, please consult your local customer service representative. Cause The transport screws have not been removed. The CD is inserted the wrong way round. There is no CD inserted. A USB storage medium is connected to the USB port. The CD does not The volume control is play back after being set too low. The device has inserted into the not been correctly device. connected. CD works intermittently The surface of the road (dropouts). is uneven. The device is not rmly installed. Fault Symptoms CDs are drawn only half way into the CD tray. NO DISC is shown in the display. CD cannot be selected using the MOD(E) button. Solution Remove the transport screws. Insert the CD right way round. Insert a CD. Remove the USB storage medium. Turn up the volume. Check the +12V and earth connection. Wait until the road becomes smoother before playing the CD. Install the device rmly. Ensure that the rear attachment is used if the vehicle does not have any suitable retainer for the rear section of the device. Try another CD. If this works correctly, the rst CD is probably damaged. Clean the CD. Please note that a maximum inclination of 20 degrees should not be exceeded! Turn the ignition key to ON or ACC. Replace the fuse by another 5 A /0,5 A fuse. Please contact your car workshop or a vehicle specialist for connection adapters may specically for your model.
Cause The microcomputer has been interfered with by electromagnetic elds. The device cannot be The control processor operated, but hangs of the device may up. have been blocked by overvoltage or undervoltage in the vehicle electrical system. No radio reception. The antenna cable is not connected.
Solution Remove the CD and reinsert it. Switch the device off and on again. Press the RESET button.

Poor radio reception.

In automatic search mode the radio does not stop at a transmitting station.
Insert the antenna cable rmly into the antenna socket of the device. It is possible that your Please contact your vehicle has a special car workshop or a antenna (phantomvehicle specialist. (For powered antenna.) other manufacturers there are specic phantom power supply adapters and voltage adapters available.) The transmission Tune in to a radio signals are too weak. station manually.

The CD is damaged.

No function.
The CD is dirty. The device may have been installed in the vehicle at the wrong angle. The ignition is switched off. One or more fuses have blown. Incorrect connection (each car manufacturer wires the ISO connection in the vehicle differently).
Device cannot be switched on or off via the ignition.
05-AR 773 DVD_GB.indd Abs1:44

19.10.2007 14:14:52 Uhr

Handling a CD

Cleaning the CD Before playing a CD, wipe it off with a clean, dust-free cleaning cloth. Pull out the CD in the direction of the arrow. CAUTION: Do not use any solvents such as petrol or thinning agents. Commercially available cleaning substances or antistatic sprays will damage the device. Inserting the CD If the CD is inserted with the printed side facing downwards, the device may be damaged. Always insert the CD with the label facing upwards. CAUTION: If there is already a CD in the CD slit, do not try to insert a second CD. This may damage the device. Touching the CD

Guarantee

The device supplied by our Company is covered by a 24 month guarantee starting on the date of purchase (receipt). During the life of the guarantee any fault of the device or its accessories ascribable to material or manufacturing defects will be eliminated free of charge by repairing or, at our discretion, by replacing it. The guarantee services do not entail an extension of the life of the guarantee nor do they give rise to any right to a new guarantee!
If you wish to make a claim under the guarantee please return the entire machine in the original packaging to your dealer together with the receipt. Defects to consumables or parts subject to wearing as well as cleaning, maintenance or the replacement of said parts are not covered by the guarantee and hence are to be paid! The guarantee lapses in case of unauthorized tampering.
After the expiry of the guarantee
After the expiry of the guarantee repairs can be carried by the competent dealer or repair service against the payment of the ensuing costs.
Always hold CDs by the edge. In order to keep the CD clean do not touch the surface. CAUTION: Do not attach any stickers or adhesive tape to the CD. Do not expose the CD to direct sunlight or sources of heat such as heating pipes. Do not leave CDs in the car if it is parked in direct sunlight as this will lead to a considerable rise in the temperature inside the car. Check all CDs for cracks, scratches and warping before you play them. It is possible that CDs that are damaged in this way cannot be played back correctly. Such CDs should not be used. Use only standard commercially available circular CDs with a 12 cm diameter! CDs with an 8 cm diameter or CDs with contours, e.g. of a buttery or heart, are not suitable. It is possible that such CDs may not only be destroyed themselves, but may also destroy the drive of the CD player. We cannot accept liability for damage caused by the use of unsuitable CDs.

05-AR 773 DVD_GB.indd Abs1:45
Proof of the guarantee is provided by the proof of purchase. Without proof of purchase no free replacement or repair will be carried out.
A AF....32 APS button...33 AUX IN....34 B BAND button...31 Bluetooth...38 Buttons on the Remote Control..3 C Changing the Angle of the Control Panel..34 CLK button...34 Connection...29 D DISP button...33 DVD Player...39 E Ejecting the CD...32 G Guarantee....45 H Handling a CD...45 I Important Additional Installation Information..30 Installation....28 Installation (Safety Information)..30 Installation Tips...27 INTRO (3INT)....34 L LO/DX button...35 M MOD button...33 MU button (Mute)...32 O Operating instructions...30 Operation...31 P PAIR button...34 PI (Programme Information)..33 Play / Pause (II)...33 PTY button...32 PWR button...33 R RANDOM (4RDM)...34 REG (Regional)...33 REL button...31 Remote control battery installation..30 REPEAT (2RPT) (Repeat)..34 RESET button...31 Road Safety...27 S SEL button....32 Safety Information...27 Switching off...33 Switching on...33 Switching to Mono..3 Switching to Stereo...3 Mute (see MU button)...32 T TA (Trafc Announcements)..32 Technical Data...43 Telephoning...38 Time (see CLK)...34 Touch Screen....35 Trafc Announcements (see TA)..32 Troubleshooting...44 U USB Connection...34
05-AR 773 DVD_GB.indd Abs1:46

19.10.2007 14:14:53 Uhr

Menu overview
General Setup Page TV Display Norm/PS Norm/LB Wide On Off English French German Spanish Italian Portuguese SPDIF Off SPDIF/RAW SPDIF/PCM On Off On Off On Off Preference Page TV Type PAL Auto NTSC English French Spanish German Italian Portuguese English French Spanish German Italian Portuguese Off English French Spanish German Italian Portuguese KID SAV 2G 3 PG 4 PGPGR 6R 7 NC-ADULT Off Change Reset

Angle Mark OSD Lang

Subtitle

SPDIF-Output

Subtitle Screen Saver Last Memory

Disc Menu

Speaker Setup Page Downmix

Parental

Dolby Digital Setup Dynamic

Password Default

05-AR 773 DVD_GB.indd Abs1:47
05-AR 773 DVD_GB.indd Abs1:48

19.10.2007 14:14:54 Uhr

05-AR 773 DVD_GB.indd Abs1:49

GARANTIE-KARTE

Garantiebewijs Carte de garantie Certicato di garanzia Tarjeta de garantia Carto de garantia Guarantee card Garantikort Karta gwarancyjna Zrun list Garancia lap