Introduction
Important Information and Customer Assistance
Operation Customer Warranty
Assistance Important Information
Federal Laws Governing the Use of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio Secondary Icons transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action. Operating Instructions Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. It is only intended to alert Notice the motorist that an emergency vehicle equipped with a Cobra Safety Alert transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area.
The Cobra line of quality products includes:

Main Icons

Safe Driving Motorists, as well as operators of emergency or service vehicles, are expected to exercise all due caution while using this product, and to obey all applicable traffic laws. Security of Your Vehicle Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft.
CB Radios microTALK Radios Radar/Laser Detectors Safety Alert Traffic Warning Systems Handheld GPS Receivers Mobile GPS Navigation Systems HighGear Accessories

Customer Assistance

Operation
Assistance Customer Assistance

Customer

Warranty
Should you encounter any problems with this product, or not understand its many features, please refer to this owners manual. If you require further assistance after reading this manual, Cobra Electronics offers the following customer assistance services:

Secondary Icons

For Assistance in the U.S.A. Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone). Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. Central Time Mon. through Fri. (except holidays) 773-889-3087 (phone). Questions English and Spanish. Faxes can be received at 773-622-2269 (fax). Notice
CobraMarineTM VHF Marine Radios CobraMarineTM Power Inverters Accessories
For more information or to order any of our products, please visit our website: www.cobra.com
12 BAND HIGH-PERFORMANCE DIGITAL RADAR/LASER DETECTOR WITH XTREME RANGE SUPERHETERODYNE TECHNOLOGY
Technical Assistance English only. www.cobra.com (on-line: Frequently Asked Questions). English and Spanish. productinfo@cobra.com (e-mail). For Assistance Outside the U.S.A. Contact Your Local Dealer

A1 English

2006 Cobra Electronics Corporation 6500 West Cortland Street Chicago, Illinois 60707 USA www.cobra.com

XRS 9330

Nothing Comes Close to a Cobra
Printed in China Part No. 480-230-P Version B

English

Controls, Indicators and Connections
Display and Product Features
Intro Operation Customer Assistance
Assistance Controls, Indicators and Connections

Display

Ordering From U.S.A.

Accessories Order Info

Call 773-889-3087 for pricing or visit www.cobra.com. For Credit Card Orders Call 773-889-3087 [Press one from the main menu] 8:00 a.m. to 6:00 p.m. Central Time, Monday through Friday. Make Check or Money Order Payable To Cobra Electronics, Attn: Accessories Dept., 6500 West Cortland Street, Chicago, IL 60707 U.S.A.

Notice

Speaker

Windshield Bracket Mount

X K Ka V S
Windshield Bracket Release Button LaserEye For 360 detection of laser and strobe signals. Audio Jack Radar, VG-2, Spectre 1, Safety and Strobe Indicators Signal Strength, Laser and City/Highway Notice Mode Indicators Signal Strength 1 (weakest) to 5 (strongest) IntelliMute Indicator
NOTE: In This Manual When steady, X K Ka V S the display will be shown: When blinking, the display will be shown: X & K will light simultaneously when indicating Ku detection:
To Order Online Please visit our website: www.cobra.com

Item # Description

Product Features
Congratulations! Youve made a smart choice by purchasing a high performance radar/laser detector from Cobra. Just look at some of the sophisticated features and capabilities your new unit includes: Xtreme Range UltraBright Data Display Superheterodyne Technology Easy-to-read with adjustable brightness With super-fast sweep circuitry, City or Highway XRS provides extra detection range Modes to reduce false alerts and the best possible advance warning Safety Alert to even the fastest radar guns Traffic warning system distinguishes Detection and Separate Alerts For: important safety alerts from other Radar signals (X, K, Ka and Ku bands, K band signals with signal strength indicated), Strobe Alert laser signals, Safety Alert signals, Emergency vehicle warning system Strobe Alert signals, VG-2 signals, Manual Mute or Auto Mute Spectre 1 signals A mute function of audio alerts LaserEye IntelliMute For 360 detection of laser and A mute function which strobe signals automatically reduces false Instant-On Ready alerts by sensing engine RPMs Detects radar guns with instant-on Mounting (very fast) speed monitoring capabilities Mounts easily on windshield Tone Alerts or dashboard With adjustable volume
This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.

420-030-N-001 420-026-N-001 545-139-N-001 CLP-2B
Straight 12V Power Cord Coiled 12V Power Cord Windshield Mounting Bracket Dual Port Power Adapter
12V DC Power Jack On-Off/ Volume Control Allows you to adjust the volume of the tone alerts.
Dim Button Allows you to adjust the UltraBright Data Display brightness for easy reading. (Also turns VG-2 and Spectre 1 alerts on and off.*)Intro
City Button For City or Highway modes to reduce false alerts.
Operation Customer Assistance Warranty
IntelliMute Button Engine RPM sensing mute function which reduces false alerts. Button turns IntelliMute on and off. (Also enters IntelliMute setting mode. ) * Secondary Icons
Mute Button For manual mute or auto mute of audio alerts. (Also turns Voice Alert on and off.*)

WARNING

* Press and hold for two seconds to access these functions.
Modifications or parts substitutions not approved by Cobra Electronics Corporation may violate FCC Rules and void your authority to operate this equipment.

A2 English

Contents
Introduction Important Information. A1 Customer Assistance. A1 Intro Operation Customer Warranty Assistance SecondaryControls, Indicators and Connections. A2 Icons Display. A3 Product Features. A3
Your Detector Installation. 2 Notice Getting Started. 5 Customer Warranty Assistance Settings. 6 Highway/City Mode. 6 UltraBright Data Display Brightness. 7 Notice Muting an Alert. 8 Auto Mute Mode. 8 IntelliMute. 9 VG-2 and Spectre 1 Alert Audio Settings. 12 K Band and Ku Band Detection.12 Detection. 13 Signals Detected. 13 Audio Alerts. 13 Visual Display. 13 Instant-On Detection. 16 Responding to Alerts. 16 Understanding Radar and Laser. 17 Maintenance. 19 Specifications. 20 Warranty Limited 1-Year Warranty. 21 Customer Assistance Product Service. 22 Warranty Trademark Acknowledgement. 23 Optional Accessories. 24 Order Info. 25

Your Detector

Intro Operation

Installation

Customer Warranty
Customer Assistance Warranty
Installation Assistance Where to Mount Your Unit

Windshield Mounting

You will get optimum performance from your detector if you Mount it at a point approximately in the center of the vehicle, as low as possible on the front windshield without obstructing the units view of the road either to the front or rear. Make sure unit is level with the road. You can also mount it directly on the dashboard.

1. Attach the rubber

cups to the bracket.
2. Make sure the rubber cups and your windshield are clean. Windshield Mounting Dashboard Mounting
3. Push the bracket firmly onto the windshield.
4. Attach the detector to the bracket. Check the angle of the unit.
The units lens must not be blocked and the LaserEye should have a clear view out the back window to allow 360 detection.
The LaserEye Should Have a Clear View
5. To adjust the angle if necessary, gently push or pull on the bracket to bend it. DO NOT use the detector to bend the bracket. 6. Plug the power cord into the detector.
Radar and laser signals pass through glass but not through other materials and objects. Objects that can block or weaken incoming signals include:

s s s s

Windshield wiper blades Mirrored sun screens Dark tinting at the top of the windshield Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM.) Consult your dealer to see if you have this option.
7. Plug the cigarette lighter adapter on the power cord into your vehicles cigarette lighter. 8. You can temporarily remove the detector whenever you wish by pressing the bracket release button and sliding it off the bracket.

Getting Started

Dashboard Mounting
Assistance Getting Started
1. Place the detector on the dashboard to find a location
where the unit has a clear, level view of the road. The angle can NOT be adjusted after mounting. 2. Remove the paper backing from one side of the hookand-loop fastener.

Power On

To Turn OnIntro Unit and Adjust the Audio Volume the Operation Customer Warranty Tone Three beeps

Ma in Ico ns

4. Attach the detector to the hook-and-loop fastener. You can remove and reattach the unit as often as you like. 6. Plug the power cord into the detector.
NOTE In some vehicles, power is supplied to the cigarette lighter even while the ignition is off. If this is the case with your vehicle, you should turn off or unplug your detector when parking for lengthy periods.
7. Plug the cigarette lighter adapter on the power cord into your vehicles cigarette lighter.

Intr o

Rotate the On-Off/ Volume control clockwise (away from you).

Op era tio n

Assistance

Se co nd ary

Ico ns

Ins tall ati on

Cu As sto sis me tan r ce

W arr an

3. Attach the pad to the dashboard at your chosen location and remove the other paper backing.

No tic e

Ca uti on

W arn ing

On-Off/ Volume Control Rotate clockwise (away from you)
Visual Display appears in the display indicating that the power is on.

Settings

When changing the Settings on your detector, please keep in mind: Buttons can have multiple functions. All settings will be stored in memory when the power is turned off and recalled when the power is turned back on.

Icons Secondary s

Assistance UltraBright Data Display Brightness
You can choose from three settings for Brightness of the display. You can cycle through the settings by repeatedly pushing the Dim button. The factory setting is Bright.

Highway/City Mode

Setting your detector to City mode delays all X band audio alerts until the signal Notice strength reaches Level 3. (A single beep will sound when the signal is first detected.) This will reduce false alerts while you are driving in, or near, urban areas where there are many sources for conflicting X band signals such as microwave towers and automatic door openers. To change settings, follow the procedure listed below, which indicates what you will see and hear as you complete each step. The factory setting is Highway mode.

Highway Mode

Bright Dark release Dim

button

Press and
Dim Button Press and release
To Change the Brightness to Dim

City Mode

City Button Press and release
Press and release the Dim button once.

Tone One beep

Visual Display Display dims
To Change the Brightness to Dark
Press and release the Dim button again.
Visual Display Display remains dim (no visual alerts will be seen)
To Change From Highway Mode to City Mode Press and release the City button. Tone One beep Visual Display To Change the Brightness to Bright Press and release the Dim button a third time. Tone Two beeps Visual Display Display returns to full brightness

c appears in the display

To Change From City Mode Back to Highway Mode Press and release the City button again. Tone Two beeps Visual Display

h appears in the display

Nothing Comes Close to a Cobra 7
Assistance Muting an Alert

IntelliMute

Your detector allows you to quickly turn off an audio Alert by momentarily pressing the Mute button. If you press the Mute button a second time during the Alert, the audio Alert will be turned back on.

Auto Mute Mode

Auto Mute will automatically reduce the audio volume of all alerts after four seconds for as long as the signal is detected. The factory setting for Auto Mute is on.

IntelliMute is a unique new feature that allows you to avoid alerts you dont need to hear because you are stopped or moving slowly. By sensing the revs (RPMs) of your engine, IntelliMute knows when you are at low Secondary Icons Operation Customer Warranty speed and automatically mutes alerts (except for strobe signals from Assistance emergency vehicles). Before IntelliMute will work, you must set an activation point for your engines revs (see page 11). Whenever the revs are below that point, IntelliMute will begin muting. The activation point will be stored in memory and recalled Notice each time the power is turned on. The factory setting is IntelliMute off. NOTE IntelliMute may not work with some vehicles because it cannot sense the engines revs. In such cases, you can reduce unwanted audio alerts by using Auto Mute and City mode when appropriate.

IntelliMute On

Mute Button Press and release
To Turn Auto Mute Off Press and release the Mute button while no alert is occurring. Tone One beep Visual Display None
IntelliMute Button Press and release
To Turn IntelliMute On Press and release the IntelliMute button. Visual Display None To Turn IntelliMute Off Press and release the IntelliMute button again. Tone One beep Visual Display None Tone Two beeps Visual Display Dot appears next to the large character on the right
To Turn Auto Mute On Press and release the Mute button again while no alert is occurring. Tone Two beeps
Assistance What to Remember While Using IntelliMute IntelliMute works with both City and Auto Mute modes.

in Icons

Whenever your engine revs are below the activation point, the dot next to the large character on the right side of the display Secondary Icons will remain lit. Above the activation point, the dot will blink twice every two seconds.
Below Activation Point Above Activation Point
IntelliMute Button Press and hold for two seconds
To Set the IntelliMute Activation Point Press and hold the IntelliMute button for two seconds.

Tone Two beeps

Visual Display None

X K Ka Notice VS

condary Icons
If, for any reason, the unit stops sensing your engines revs, IntelliMute will indicate an error and automatically turn off. The rev point you set will be stored in the units memory when power is turned off and recalled each time the power is turned on. NOTE The rev point must be reset if you use your detector in a different vehicle.
Rev yourMain Icons to engine None the level you wish to set (recommend slightly above idle) and hold revs steady for two seconds. At the desired rev level, press and release the IntelliMute button. Secondary Icons
Three bars will flash in succession

Operation Warranty

Secondary Icons Assistance

Caution

Warning

Three beeps

All three bars flash three times
Customer Intro Assistance

Warranty Operation

NOTE When initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individual Customer Warranty Assistance preferences and driving style.
Customer Setting the IntelliMute Activation Point Assistance Your detector must be installed in your vehicle.

Warning Notice

NOTE If the unit is unable to sense usable pulses within three seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn off. Tone Four beeps Visual Display

E appears

CAUTION Do not attempt to set the rev point while driving. Warning Your vehicle should be parked and idling.
IntelliMute must be turned on before setting the activation point. You will hear a series of beeps as you follow the steps on page 11.
10 English Nothing Comes Close to a Cobra 11

Detection

Assistance VG-2 and Spectre 1 Alert Audio Settings
The detector is undetectable by police VG-2 and Spectre 1 radar detector detectors and will alert you when such a device is in use near your vehicle. During the alert, the unit continues to detect other signals. You can choose Secondary Icons whether or not you want your unit to show VG-2 and Spectre 1 alerts. The factory setting is VG-2 and Spectre 1 alert off.

On/Off Indicator

Detection Assistance Signals Detected
The tables on the following pages show you the types of Signals your detector will detect, as well as the visual alerts it provides for each of them.

Audio Alerts

A distinctly different Alert tone is used for each type of signal detected (including separate tones for each laser signal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as you approach the signal Notice source. The repeat rate of the tones gives you useful information about the signal detected. (See responding to alerts on page 16.)

Dim Button Press and hold for two seconds
To Turn VG-2 and Spectre 1 Alerts On While no signal is being detected, press and hold the Dim button for two seconds again. Tone Two beeps Visual Display

Visual Display

V will blink twice

in the display

X Signal Detected
An indication of the type of signal detected will appear in the UltraBright data Display. During X, K, Ka and Ku alerts, a number will also appear, indicating the strength of the signal detected. (1 = weakest, 5 = strongest)

K Signal Detected

Ka Signal Detected

Ku Signal Detected

K Band and Ku Band Detection
To Turn K Band On and Off While no signal is being detected, press and hold both the Dim and City buttons for two seconds. Tone K On = Two beeps K Off = One beep Visual Display
During laser alerts the letter L will appear, instead of the signal strength indication.

Laser Signal Detected

K will blink twice

K will blink once

During VG-2 or Spectre 1 alerts, the letter V will appear. It will be steady during VG-2 and blink during Spectre 1.
VG-2 Alert Signal Detected Spectre 1 Alert Signal Detected
To Turn Ku Band On and Off While no signal is being detected, press and hold the City button for two seconds again.

12 English

Tone Ku On = Two beeps Ku Off = One beep

X and K will blink twice

During Safety Alert and Strobe Alert the letter S will appear. It will be steady during a Safety Alert and will blink during a Strobe Alert.
Safety Alert Signal Detected Strobe Alert Signal Detected

X and K will blink once

Radar Signals and Visual Displays Type of Signal X Band Radar
Strobe Alert Signals and Visual Displays Visual Display X and Signal Strength K and Signal Strength Ka and Signal Strength X K and Signal Strength
Type of Signal 3M Opticom or Tomar*

Visual Display S Blinks

K Band Radar Ka Band Radar Ku Band Radar
* Your detector provides 360 detection of this signal.
Strobe Alert Signal Detected
Safety Alert Signals and Visual Displays Type of Signal Laser Signals and Visual Displays
Visual Display S is Steady S is Steady S is Steady
Emergency Vehicles Visual Display

Type of Signal LTI 20-20* LTI Ultra-Lyte* Kustom Signals ProLaser*
Road Hazards Operation Customer Trains
Kustom Signals ProLaser III* Customer Warranty
L is Steady L is Steady L is Steady L is Steady
Safety Alert Signal Detected
* Your detector provides 360 detection of these signals.
Secondary Icons Main Icons
NOTE There are different tones for each Safety Alert.
VG-2 and Spectre 1 Alert Signals and Visual Displays Type of Signal Visual Display
NOTE Beep rate changes with different laser alerts.
Interceptor VG-2 Customer Spectre 1

V is Steady V Blinks

Spectre 1 Alert Signal Detected
VG-2 Alert Signal Detected
NOTE There are different tones for each alert.
Nothing Comes Close to a Cobra 15

14 English

Understanding Radar and Laser
Assistance Instant-On Detection
Your detector is designed to detect Instant-On speed monitoring signals, which can suddenly appear at full strength.
Assistance Understanding Radar and Laser Radar Speed Monitoring Systems
NOTE You should take appropriate action immediately whenever an instant-on alert is given.
Four band frequencies have been approved by the Federal Communications Commission (FCC) for use by speed monitoring radar equipment: X band K band Ka band Ku band

Responding to Alerts

Description
Tone repeats slowly at first, then speeds up rapidly. Tone sounds one time only. Tone instantly begins repeating rapidly.
10.525 GHz 24.150 GHz 33.400 36.00 GHz 13.435 GHz

Interpretation

Probably police radar

Recommended Response

FULL ALERT
Your detector detects signals in all four radar bands.

VG-2 and Spectre 1

VG-2 and Spectre 1 are detector detectors that work by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1 signals and will alert you when a device is in use near your vehicle, if you so choose.
Probably a false alarm, but possibly pulsed radar, VG-2, or Spectre 1 nearby Radar, VG-2, or Spectre 1 nearby has been activated suddenly

Exercise caution

Safety Alert Traffic Warning System
FCC-approved Safety Alert transmitters emit microwave radar signals that indicate the presence of a safety-related concern. Depending on the frequency of the signal emitted, it can indicate a speeding emergency vehicle or train, or a stationary road hazard. Because these microwave signals are within the K band frequency, most conventional radar detectors will detect Safety Alert signals as standard K band radar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each. Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing. Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common. When you receive such an alert, please watch for emergency vehicles ahead of you, on cross streets and behind you. If you see an emergency vehicle approaching, please pull over to the right side of the road and allow it to pass.
Nothing Comes Close to a Cobra 17
Tone repeats slowly as you Probably police approach a hill or bridge, radar beyond the then speeds up sharply as hill or bridge you reach it. Tone repeats slowly for a short period. Any type of laser alert. Any Safety Alert or Strobe Alert. Probably a false alarm Laser alerts are never false alarms You are nearing an emergency vehicle, railroad crossing, or road hazard (construction, accident, etc.)
Exercise caution FULL ALERT Exercise caution

16 English

Maintenance

Strobe Alert

Special strobes mounted on the light bars of authorized emergency vehicles (fire trucks, police cars, ambulances) automatically change traffic signals as the vehicle approaches an intersection. These strobes and the Secondary Icons special strobe detectors located on the traffic signals, introduced fairly recently by 3M and Tomar, are already in use in more than 1000 cities nationwide. Cobras exclusive Strobe Alert detector will detect these special strobes and give an emergency vehicle alert. When you receive such an alert, please watch for an approaching Notice emergency vehicle and pull over to allow it to pass. To inquire about coverage in your area, contact your local fire and police departments.
Assistance Maintenance Maintenance of Your Radar Detector
Your detector is designed and built to give you years of trouble-free performance without the need for service. No routine Maintenance is required. If your unit does not appear to be operating properly, please follow these troubleshooting steps:

Unit Dimensions and Weight Dimensions* (H x W x D) 113" x 234" x 413" (34 mm x 70 mm x 110 mm) Weight* 4.83 oz. (137 g)
* Dimensions and weight measurements are approximate.
This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148. Additional patents may be listed inside the product or pending.

20 English

Product Service

Warranty Intro

For any questions about operating or installing this new Cobra product, or if parts are missingPLEASE CALL COBRA FIRSTdo not return this product to the store! See customer assistance on page A1. If this product should require factory service, please call Cobra first at 773-889-3087 BEFORE sending the product. This will ensure the fastest turnaround time on any repair.
Trademark Acknowledgement

ry Icons

Cobra, 6 Band, 9 Band, DigiView, EasySet, Extra Sensory Detection, IntelliShield, LaserEye, Nothing Comes Close to a Cobra, Safety Alert Traffic Warning System, Strobe Alert, VG-2 Alert, Xtreme Range Superheterodyne and the snake design are registered trademarks of Cobra Electronics Corporation, USA.
If Cobra asks that the product be sent to its factory, the following must be Notice furnished to have the product serviced and returned: 1. Send the complete unit, including power cord. (It is not necessary to include the mounting bracket.) 2. For warranty repair, enclose some form of proof-of-purchase, such as a photocopy or carbon copy of a sales receipt. If you send the original receipt, it cannot be returned. 3. Enclose a typed or clearly written description of the problem you are having with your unit, plus the name and address where you want the unit returned. 4. Pack the unit securely to prevent damage during transit. If possible, use the original packing materials. 5. Ship prepaid and insured using a traceable carrier such as United Parcel Service (UPS), Federal Express, or Priority mail with delivery confirmation. Ship to: Cobra Factory Service, Cobra Electronics Corporation, 6500 West Cortland Street, Chicago, IL 60707 U.S.A. 6. Please allow three to four weeks before contacting us about the status of your service. Call 773-889-3087 for assistance. If your unit is under warranty, it will either be repaired or replaced upon receipt, depending on the model. If your unit is out of warranty, you will receive a letter informing you of the repair or replacement charge.
Cobra Electronics Corporation, 12 Band, IntelliMute, Revolution Series, RoadReady, SmartPower, Spectre Alert, UltraBright, and Voice Alert are trademarks of Cobra Electronics Corporation, USA. Notice Opticom is a trademark of 3M Corporation. Instaclear for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear for GM is a registered trademark of General Motors Corporation. 20-20 and Ultra-Lyte are trademarks of Laser Technology, Inc. ProLaser and ProLaser III are trademarks of Kustom Signals, Inc. Bee III and Pop are a trademarks of MPH Industries. Spectre is a trademark of Stalcar. Interceptor VG-2 is a trademark of TechniSonic Industries LTD. Tomar is a registered trademark of TOMAR Electronics, Inc.

22 English

Optional Accessories
You can find quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra. See ordering info on page 25.
Straight 12V DC Power Cord Includes plug and fuse Item # 420-030-N-001
Windshield Mounting Bracket Includes suction cups Item # 545-139-N-001
Coiled 12V DC Power Cord Includes plug and fuse Item # 420-026-N-001
Dual Port Power Adapter Includes adjustable plug (up to 90) and fuse Item # CLP-2B

24 English