Page 2

Overview

Your Detector

Installation
This manual describes the simple steps for mounting, setting up and using your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive. Before you begin your installation, please read the Important Information section on page A1 and use the descriptions and feature lists on pages A2 and A3 to become familiar with your new detector.
Installation Where to Mount Your Unit
You will get optimum performance from your detector if you mount it at a point approximately in the center of the vehicle, as low as possible on the front windshield without obstructing the units view of the road either to the front or rear. You can also mount it directly on the dashboard.
About Your Detector Display
This detectors innovative new display provides more, easier-to-use information than any technology to date. Using an OLED (Organic Light Emitting Diode) screen, the display offers large graphical alerts to signals as they are detected.

Windshield Mounting

Dashboard Mounting
Do not be alarmed by the nearly blank display you see when you first turn the unit on. The detector will function and alerts will appear as signals are detected. You can also elect to turn on the built-in Compass, IntelliMute and Car Voltage, so that they appear during normal operation. The initial and startup screens are shown on page 6.
The units lens must not be blocked and the LaserEye should have a clear view out the back window to allow 360 detection.
The LaserEye Should Have a Clear View

Programming

EasySet Programming lets you conveniently customize the operation of your detector by changing the settings. You may want to start using the detector with the factory settings and then make changes after you are more familiar with the unit.

About This Manual

Please take a moment to learn about some special features of this manual.

Modular Descriptions

Once the detector is in use, this manual can be used as a ready reference to individual topics as needed. Each topic is completely covered in its section and cross-references to related topics are included where appropriate.

Set-up is complete when the display continuously shows the City or Highway icon and if these features are turned on: Compass, IntelliMute, and Car Battery Voltage.
Display Brightness Control

Power On

NOTE When the system is first turned on from new, only the City or Highway icon will show on the screen because the Show Compass, IntelliMute and Show Car Battery Voltage functions are set to off at the factory. See pages 14, 16 and 19 to turn these functions on. NOTE In some vehicles, power is supplied to the cigarette lighter even while the ignition is off. If this is the case with your vehicle and you have turned the SmartPower off, you should turn off or unplug your detector when parking for lengthy periods. Cobra recommends leaving SmartPower at the factory setting, which is on. See page 18.
Your detector has a Bright display mode (for daytime driving) and three levels of the Dim display mode: I Dim for dusk driving. NOTE The display will show I Dimmer for night driving. small dots to indicate I Dark to prevent all visual alerts from displaying. the unit is tuned on. The factory setting is Bright. This level can be changed in programming mode (see page 19.) You can toggle between Bright and Dim modes by pressing the Dim button.

Settings Not Set

Dim Button Press and release
NOTE When you change to Dim mode, the unit will enter whichever dim default mode is set at the time.
Nothing Comes Close to a Cobra 7

Page 8

Auto Dimmer and Screensaver
Your detector is equipped with Auto Dimmer and Screensaver functions to prolong the life of your screen.

Muting an Alert

Your detector allows you to quickly turn off an Audio Alert by momentarily pressing the Mute button. If you press the Mute button a second time during the alert, the Audio Alert will be turned back on. After the current alert is gone, the next alert will be heard.

Highway / City Mode

Your detector has a Highway mode and three different levels of City modes: City X, City X Beep Off and City X+K. Highway mode provides full response to all signals detected. The City modes reduce false alerts while you are driving in or near urban areas where there are many sources for conflicting X or K band signals such as microwave towers and automatic door openers. The factory setting is Highway. The factory City mode default setting is City X; it can be changed in programming mode (see page 11). You can toggle between Highway and City modes by pressing the City

EasySet Programming Buttons:
4. Press the Dim button (above the down arrowhead on the display) to toggle the option on or off or to step through its multiple choices. 5. Repeat steps 3 and 4 to move to and set the next desired option(s). 6. Press the Menu/Save button when finished to save the settings and exit EasySet program mode. Or, simply wait 15 seconds without pressing any buttons.
NOTE If power is turned off while in Program mode, option settings are saved to those in effect before Program mode was entered.
Mute Button Press to move counterclockwise to desired setting. Dim Button Press to choose an option within setting.
City Button Press to move clockwise to desired setting.
Menu/Save Button Press to reach the opening program screen.

10 English

Page 12

Program Flow Diagrams

User Settings Programming
User Programming allows you to adjust the units display and sounds to your preferences. The User Settings can be selected using the Mute and City buttons by scrolling through the settings as shown in the program flow diagram below. The User Programming Menu Guide on page 34 is a handy reference showing the tone, visual display and voice prompts that accompany each setting. After selecting a setting, use the Dim button to choose an option within the setting.
Alert Settings Programming
Alert Programming allows you to selectively turn on or off detection of some signals. The Alert Settings can be selected using the Mute and City buttons by scrolling through the settings as shown in the program flow diagram below. The Alert Programming Menu Guide on page 36 is a handy reference showing the tone, visual display and voice prompts that accompany each setting. After selecting a setting, use the Dim button to choose an option within the setting.
NOTE When you choose Alert Settings (page 11, Step 2b), the system displays whichever setting was last changed.
K Band Detection X Band Detection Ku Band Detection VG-2 Audio
Not shown setting if VG 2 is OFF.
NOTE When you choose User Settings (page 11, step 2a), the system displays whichever setting was last changed.
Setting Selection Buttons:
Mute Button Press to move counterclockwise around the loop.
City Button Press to move clockwise around the loop. Dim Button Press to choose an option within setting.

Restore Factory Settings

Pop Detection

Spectre 1 Audio

Not shown if Spectre 1 is OFF.

VG-2 Detection

City Mode (Default)

IntelliMute

Safety Alert

Spectre 1 Detection

Warn Low Car Voltage

Auto Mute

Not shown if Intellimute is OFF.
Set IntelliMute Set Compass

Car Voltage

Not shown if Show Compass is OFF.
This detector allows you to customize its operation by changing settings in the User Programming and the Alert Programming modes. (See page 11 for entering the EasySet Programming mode.) Also, refer to the Appendix (pages 3436) while programming. These show the lists of User and Alert settings. Features of the programmable settings are described on the following pages.

Alert Type (Voice/Tone)

Color Theme Display (Brightness) SmartPower Show Compass

12 English

Page 14

Settings

User Settings City Mode Default
City Mode Default makes three levels of Audio Alert suppression available when you toggle from Highway to City mode (see page 8). The factory setting is City X. City X sounds a single beep when an x band signal is first detected. The alert then sounds when signal strength reaches level 3. City X+K combines the City X mode with prevention of K band audio alerts until the signal strength reaches level 2. City X Beep Off blocks all X band audio alerts until the signal strength reaches level 3.
NOTES IntelliMute may not work with some vehicles because it cannot sense the engines revs. In such cases, you can reduce unwanted audio alerts by using Auto Mute and City mode when appropriate. NOTES The rev point must be reset if you use your detector in a different vehicle. NOTES When initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individual preferences and driving style. CAUTION Do not attempt to set the rev point while driving. Your vehicle should be parked and idling to avoid a collision during the process.

IntelliMute Mode

IntelliMute is a unique feature that allows you to avoid alerts you dont need to hear because you are stopped or moving slowly. By sensing the revs (RPMs) of your engine, IntelliMute knows when you are at low speed and automatically mutes alerts (except for strobe signals from emergency vehicles). It works with all City and Auto Mute modes. Before IntelliMute will work, you must set an activation point for your engines revs (see page 15). Whenever the revs are below that point, IntelliMute will begin muting. The activation point will be stored in memory and recalled each time the power is turned on. The factory setting is IntelliMute off. An IntelliMute icon will appear in the display when IntelliMute is on and activation is set. Whenever engine revs are below the activation point, the arrow points down. When revs are above the activation point the arrow points up.

16 English

Page 18

SmartPower Mode

Your detector includes the SmartPower feature that, when turned on, will put the unit into Standby mode (low power) 15 minutes after the cars engine has been turned off. Before SmartPower enters Standby mode, you will hear three beeps and SmartPower will flash on the display. To return the unit to normal Power mode and exit Standby mode, start the car, press any button or turn the unit off and then on again. The factory setting is SmartPower on.
SmartPower Entering Standby Mode (Flashing)
Car Battery Voltage Display Mode
Your detector can sense your vehicles electrical system voltage (Car Battery Voltage) and show it on the display during normal operation of the unit. The factory setting is Car Battery Voltage on.
Car Battery Low Voltage Warning
In addition to displaying system voltage, your detector can provide a warning that battery voltage is low so that timely steps can be taken to correct the problem. The Car Battery Low alert is triggered when the voltage drops below 11.9 volts. Following the alert, the unit enters SmartPower mode to avoid further draining your car battery (see page 18). The factory setting is Car Battery Low off.
From the Restore Factory Settings screen, you can quickly and conveniently restore your detector to its original settings. Confirmation messages are provided during the process.
Customizable Display Colors
Your detector includes the Color Theme feature that allows you to customize the display screen color scheme to match your cars dash illumination: Multi-Color, Red, Blue, Orange, or Green. The factory setting is Multi-Color.

Dim Mode Default

You can set the default level for the Dim mode (Dim, Dimmer or Dark) as discussed in the Display Brightness Control section on page 7. The factory setting is Dim.

18 English

Page 20

Detection

Alert Settings Pop Alert
When Pop Detect mode is on, Pop radar signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is Pop Detect off.

Spectre 1 Audio Mode

When Spectre 1 Audio mode is on, alerts will be sounded as well as being displayed on the screen. This setting is only available if Spectre 1 Alert is on. The factory setting is Spectre 1 Audio off.
When Safety Alert mode is on, Safety Alert radar signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is Safety Alert on.

X Band Alert

When X Band Detect mode is on, X Band radar signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is X Band Detect on.

K Band Alert

When K Band Detect mode is on, K Band radar signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is K Band Detect off.
Detection Signals Detected
The tables on the following pages show the types of Signals your detector will detect, as well as the visual alerts it provides for each of them.

Ku Band Alert

When Ku Band Detect mode is on, Ku Band radar signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is Ku Band Detect off.

Audio Alerts

A distinctly different Alert tone is used for each type of signal detected (including separate tones for each laser signal). For X, K, Ka and Ku band radar signals, the tones will repeat faster as you approach the signal source. The repeat rate of the tones gives you useful information about the signal detected. See responding to alerts on page 25.

VG-2 Alert

The detector is undetectable by VG-2 detection devices and can alert you when such a device is in use near your vehicle. When VG-2 Detect mode is on, VG-2 signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is VG-2 Detect off.

Visual Display

An indication of the type of signal detected will appear in the OLED Data Display. During X, K, Ka and Ku alerts, you will also see the numbers from one to five, indicating the strength of the signal detected.

VG-2 Audio Mode

When VG-2 Audio mode is on, alerts will be sounded as well as being displayed on the screen. This setting is only available if VG-2 Alert is on. The factory setting is VG-2 Audio off.

Spectre 1 Alert

The detector is undetectable by Spectre 1 detection devices and can alert you when such a device is in use near your vehicle. When Spectre 1 Detect mode is on, Spectre 1 signals will be detected and an alert will be given. During the alert, the unit will continue to detect other signals. The factory setting is Spectre 1 Detect off.

20 English Nothing Comes Close to a Cobra 21

Page 22

Type of Signal Visual Display Voice Laser Alert

Signal Strength Chart

Signal Strength = 1 Signal Strength = 2 Signal Strength = 3 Signal Strength = 4 Signal Strength = 5
Laser Signals and Visual Displays

LTI 20-20*

(Weakest Signal)

(Strongest Signal)

LTI Ultra-Lyte*

Laser Alert

Radar Signals and Visual Displays Type of Signal X Band Radar Visual Display Voice X Alert Kustom Signals ProLaser* Laser Alert
Kustom Signals ProLaser III* K Band Radar K Alert
* Your detector provides 360 detection of these signals.

Ka Band Radar

Ka Alert NOTE Beep rate changes with different laser alerts.

Ku Band Radar

Ku Alert
Strobe Alert Signals and Visual Displays Type of Signal 3M Opticom or Tomar* Visual Display Voice Emergency Vehicle Approaching

Pop Radar Mode

Pop Alert

22 English

Page 24
Safety Alert Signals and Visual Displays Type of Signal Emergency Vehicles Visual Display Voice Emergency Vehicle Approaching

Instant-On Detection

Your detector is designed to detect Instant-On speed monitoring signals, which can suddenly appear at full strength. NOTE You should take appropriate action immediately whenever an instant-on alert is given.

Road Hazards

Road Hazard Ahead
Your detector is designed to detect single pulse mode radars. These radars are designed to have a low probability of detection. You should note that these radar guns have a much shorter range while in this mode.

Trains

Train Approaching

Responding to Alerts

Tone repeats slowly at first, then speeds up rapidly.

Interpretation

Probably police radar. Probably a false alarm, but possibly pulsed radar, Spectre 1 or VG-2 nearby. Radar, Spectre 1 or VG-2 nearby has been activated suddenly. Pop mode gun very close. Probably police radar beyond the hill or bridge. Probably a false alarm. Laser alerts are never false alarms. You are nearing an emergency vehicle, railroad crossing, or road hazard (construction, accident, etc.).

Recommended Response

FULL ALERT Exercise caution
NOTE There are different tones for each Safety Alert. VG-2 and Spectre 1 Alert Signals and Visual Displays Type of Signal VG-2 Alert Visual Display Voice VG-2 Alert
Tone sounds one time only. Tone instantly begins repeating rapidly. Pop mode tone. Tone repeats slowly as you approach a hill or bridge, then speeds up sharply as you reach it.

FULL ALERT FULL ALERT FULL ALERT

Spectre 1

Spectre Alert
Tone repeats slowly for a short period. Any type of laser alert. Any Safety Alert or Strobe Alert.
Exercise caution FULL ALERT Exercise caution
NOTE There are different tones for each alert.

24 English

Page 26
Understanding Radar and Laser
Understanding Radar and Laser Radar Speed Monitoring Systems
Four band frequencies have been approved by the Federal Communications Commission (FCC) for use by speed monitoring radar equipment: X band K band Ka band Ku band 10.525 GHz 24.150 GHz 33.400 36.00 GHz 13.435 GHz

Strobe Alert

Special strobes mounted on the light bars of authorized emergency vehicles (fire trucks, police cars, ambulances) automatically change traffic signals as the vehicle approaches an intersection. These strobes and the special strobe detectors located on the traffic signals, introduced fairly recently by 3M and Tomar, are already in use in more than 1000 cities nationwide. Cobras exclusive Strobe Alert detector will detect these special strobes and give an emergency vehicle alert. When you receive such an alert, please watch for an approaching emergency vehicle and pull over to allow it to pass. To inquire about coverage in your area, contact your local fire and police departments.
Your detector detects signals in all four radar bands.

VG-2 and Spectre 1

VG-2 and Spectre 1 are detector detectors that work by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1 signals and will alert you when a device is in use near your vehicle, if you so choose.

LIDAR (Laser)

The correct name for the technology that most people refer to as laser is actually LIDAR, which stands for Light Detection and Ranging. LIDAR operates much like radar. Its signal spreads out like a radar signal, though not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles, tree branches, etc., will prevent valid speed measurement. Some common questions about LIDAR include: I Does weather have any affect on LIDAR? Yes. Rain, snow, smoke, fog, or airborne dust particles will reduce the effective range of LIDAR and can, if dense enough, prevent its operation.

Safety Alert Traffic Warning System
FCC-approved Safety Alert transmitters emit microwave radar signals that indicate the presence of a safety-related concern. Depending on the frequency of the signal emitted, it can indicate a speeding emergency vehicle or train, or a stationary road hazard. Because these microwave signals are within the K band frequency, most conventional radar detectors will detect Safety Alert signals as standard K band radar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each. Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing. Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common. When you receive such an alert, please watch for emergency vehicles ahead of you, on cross streets and behind you. If you see an emergency vehicle approaching, please pull over to the right side of the road and allow it to pass.

26 English

Can LIDAR operate through glass? Yes. Newer LIDAR guns can obtain readings through most types of glass. However, the laser pulse also can be received through glass to trigger an alarm by your detector. Can LIDAR operate while in motion? No. Because LIDAR operates by line of sight, the person using it cannot drive the vehicle, aim and operate the gun all at the same time. Is LIDAR legal to use? Yes. It is legal in all 50 states.

Page 28

Maintenance

Specifications

Pop Radar Guns
The Pop mode Radar Gun is a single pulse Doppler radar that is a feature of a K and Ka (Bee III Ka radar gun) band Instant-On radar gun. It uses a single short time pulse to measure the target vehicles speed. Despite the fact that the short, single pulse makes the unit very sensitive to officer hand and vehicle movement and reduces the range of the gun in Pop mode to 50% of its range in Continuous Wave mode, this feature is added in an attempt to make the radar gun invisible to Radar Detectors. Although your detector can sense Pop signals beyond the effective range of Pop radar guns, there will be a signal to sense only if a gun is triggered. In addition, the Pop mode receiver section is more prone to false alerts because of its extra sensitivity. This is especially so in urban areas. As a result, you should consider using the Pop Detect mode only in highway and rural situations. Cobra Electronics has included a user selectable on or off Pop Detect mode.
Band and Frequencies Band X Band K Band Safety Alert Traffic Warning System Frequencies 10.525 24.125 24.070 24.110 24.190 24.230 Ka Band Ku Band Laser Strobe 34.700 13.700 0.050 0.125 0.010 0.010 0.010 0.010 1.300 0.300 GHz GHz GHz GHz GHz GHz GHz GHz nm nm

For any questions about operating or installing this new Cobra product, or if parts are missingPLEASE CALL COBRA FIRSTdo not return this product to the store. If this product should require factory service, please call Cobra before sending the product. This will ensure the fastest turn-around time on any repair. If Cobra asks that the product be sent to its factory, the following must be furnished to have the product serviced and returned: 1. For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction or carbon of a sales receipt. Make sure the date of purchase and product model number are clearly readable. If the originals are sent, they cannot be returned; 2. Send the entire product; 3. Enclose a description of what is happening with the product. Include a typed or clearly printed name and address of where the product is to be returned, with phone number (required for shipment). 4. Pack product securely to prevent damage in transit. If possible, use the original packing material; 5. Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or Priority Mail to avoid loss in transit to: Cobra Factory Service Cobra Electronics Corporation 6500 West Cortland Street Chicago, Illinois 60707 U.S.A.; 6. If the product is in warranty, upon receipt of the product it will either be repaired or exchanged depending on the model. Please allow approximately weeks before contacting Cobra for status. If the product is out of warranty, a letter will automatically be sent with information as to the repair charge or replacement charge. For any questions, please call 773-889-3087 for assistance.

30 English

Page 32
Trademark Acknowledgement

Accessories

Cobra, 6 Band, DigiView, EasySet, Extra Sensory Detection, HighGear, IntelliShield, microTALK, LaserEye, Safety Alert Traffic Warning System, Strobe Alert, VG-2 Alert and Nothing Comes Close to a Cobra are registered trademarks of Cobra Electronics Corporation. Cobra Electronics Corporation, 11 Band, 12 Band, IntelliMute, Road Ready, SmartPower, Spectre 1 Alert, UltraBright, Voice Alert and Xtreme Range Superheterodyne are trademarks of Cobra Electronics Corporation. Opticom is a trademark of 3M Corporation. Instaclear for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear for GM is a registered trademark of General Motors Corporation. 20-20 and Ultra-Lyte are trademarks of Laser Technology, Inc. ProLaser and ProLaser III are trademarks of Kustom Signals, Inc. Bee III and Pop are a trademarks of MPH Industries. Spectre is a trademark of Stalcar. Interceptor VG-2 is a trademark of TechniSonic Industries LTD. Tomar is a registered trademark of TOMAR Electronics, Inc.

Optional Accessories

You can find quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra. See ordering info on page 37.
Straight 12V DC Power Cord Includes plug and fuse Item # 420-030-N-001
Windshield Mounting Bracket Includes suction cups Item # 545-139-N-001
Coiled 12V DC Power Cord Includes plug and fuse Item # 420-026-N-001
Dual Port Power Adapter Includes adjustable plug (up to 90) and fuse Item # CLP-2B

32 English

Page 34
Visual Display Visual Display

Appendix Introduction

User Programming Menu Guide Mode Set City mode default Page 14 Tone Two beeps One beep One beep Set IntelliMute mode Page 15 Two beeps One beep Two beeps Voice City X Mode Set AutoMute mode Page 16 Tone Two beeps One beep None Voice Auto Mute On Auto Mute Off Voice Alert Tone Alert Compass Off Compass On Set Compass
User Programming Menu Guide (continued) Mode Set SmartPower mode Page 18 Set display Dim mode default Page 18 Tone Two beeps One beep Two beeps Visual Display Voice Smart Power On Smart Power Off Dim Mode Set car battery voltage display mode Page 19 Set battery Two low car beeps voltage warning Page 19 Dark Restore factory settings Page 19 Red Blue Orange Green Two beeps One beep Tone Two beeps One beep Voice Display Car Voltage Off Display Car Voltage On Car Voltage Warning Off Car Voltage Warning On Restore Factory Settings
City X, K City X Beep Off Intelli Mute Off Intelli Mute On Set Engine Revs
Set Voice or Tone mode Page 16

One beep One beep

Dimmer

Set Compass mode Page 17

Two beeps One beep
Set IntelliMute setup* Page 15
Set Two Compass** beeps Page 17 ** Not shown if Compass is off. Complete
instructions for calibrating the Compass are shown on the referenced page and on the separate insert.
Set Two customizable beeps display colors*** One beep Page 18
* Not shown if IntelliMute is off. Complete
instructions for IntelliMute setup are shown on the referenced page.

*** Press Dim

repeatedly for all optional colors.
NOTE Factory defaults are highlighted in light gray. See referenced pages for more information on the modes.

34 English

Page 36
Alert Programming Menu Guide Mode Set Pop Detect mode Page 20 Tone Two beeps One beep Voice Pop Off Mode Set VG-2 Audio mode* Page 20 Tone Two beeps One beep Two beeps One beep Two beeps One beep Voice VG-2 Audio On VG-2 Audio Off Spectre On Spectre Off Spectre Audio On Spectre Audio Off Safety Alert On Safety Alert Off

Pop On

Set X Band Two Detect beeps mode One Page 20 beep Set K band Two detect beeps mode One Page 20 beep Set Ku Band Detect mode Page 20 Set VG-2 Detect mode Page 20 Two beeps One beep Two beeps One beep

Set Spectre 1 Detect mode Page 20
Set Spectre 1 Audio mode** Page 21
Ku On Set Safety Two Alert mode beeps Ku Off Page 21 One beep VG-2 On VG-2 Off * Not shown if VG-2 Detect is off. ** Not shown if Spectre 1 Detect is off.
Nothing Comes Close to a Cobra 36

Recommendations for operating radar detectors
LASER-Blinder M25/M40 X-TREME is operating in all European countries. Valentine One (RC) and BEL RX-65 Euro can be used europewide. All others are ideal for the countries listed.
BEL Sti Driver ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 Whistler 948 Euro SpeedCrystal S Naxel 2020 BEL Sti Driver ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 Whistler 948 Euro BEL Sti Driver ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 SpeedCrystal Naxel 2020 BEL Sti Driver BEL TARGET 966 EVO Whistler 948 Euro BEL Vector 995 International BEL Target 966 EVO BEL Vector 995 International Whistler 948 Euro Escort Solo S2 SpeedCrystal S Naxel 2020 Valentine One / Valentine One RC BEL Vector 995 International Whistler 948 Euro BEL RX-65 Euro SpeedCrystal S Naxel 2020 BEL Sti Driver BEL VECTOR 995 International Escort Passport 8500 X-50 Whistler 948 Euro BEL Sti Driver BEL VECTOR 995 International Whistler 948 Euro SpeedCrystal S Naxel 2020 BEL Sti Driver BEL VECTOR 995 International ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 Whistler 948 Euro
http://www.radar-shop.de order@radar-shop.de
BEL Sti Driver BEL VECTOR 995 International ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50
Valentine One / Valentine One RC BEL TARGET 966 EVO BEL RX 65 Euro Whistler 948 Euro SpeedCrystal S Naxel 2020 Valentine One / Valentine One RC BEL TARGET 966 EVO SpeedCrystal S Naxel 2020 Whistler 948 Euro Valentine One / Valentine One RC BEL RX-65 Euro BEL VECTOR 995 International BEL Target 966 EVO Whistler 948 Euro Cobra XRS 9930/9730 BEL RX-65 Euro BEL VECTOR 995 International ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 Whistler 948 Euro BEL VECTOR 995 International ESCORT PASSPORT 9500i ESCORT PASSPORT 8500 X-50 Whistler 948 Euro