This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 3- highligh the region line ,press "play" to select and press "0" to change. 4- press "play" againg to save. Coby DVD-527 with no disk in the player press: Setup, Vol+, Vol-, Vol+, Volin the right upper corner a current region code would appear. You could switch between 1,2,3,4,5,6 or 255 using Right and Left buttons. I beleive, 255 is for multy-region. If you press Up (or Down) button you can get into macrovision menu from here. Again, using Left or Right buttons switch between 3000 (Off) and 3001 (On) values. Coby DVD-606 Method 1: At stop mode, press "Set up" button on remote. Set up menu shows up. Press "2188" on remote. In addition to the current sub menus on set up menu, "Version" sub menu appears in the middle of screen. Press "Version" menu. Region code menu shows up Adjust the zone number using up or down button on remote. Press "Set up" on remote to save the setting. Method 2: At stop mode, press SET UP button on remote Press VOL+,VOL-,VOL+,VOL- until you see "VER 1" at upper right corner on screen Press Right or Left arrow on remote to adjust the number of region ver 1 = region1, ver 2 = region2, etc.. ver 255 = multizone Coby DVD-615 Method 1: Press Menu Press 1, 9 Menu appears Select region by pressing PLAY Change the region to 0 (number zero) Press PLAY Press door open and close Power off
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Method 2: 1. Power on 2. Open tray 3. On remote press 2812, region menu will appear 4. Use "enter" button on remote to choose region number or choose "9" for all regions. 5. Close Tray Method 3: Open Tray Press Set up on remote Enter 8,8,8,8 on remote Press Next on remote VERSION appears on menu Select VERSION Change region number / 0 for multizone Press SET UP to exit Off and On the player Method 4: I have a Coby -615 with Karaoke to change region code: Power On Open Tray, Press 2812, in upper left corner 3 dashes --will appear as you press the numbers, upon hitting the last number Region Menu overlay will appear. Use ENTER button to choose number, I think "9" is for all regions. Close tray, shut off machine. The Numbers "8888" are the unlock code for changing the rating value, PG,R,and so on in the Rating section of the SETUP MENU. Coby DVD-626 Method 1: 1. Turn the DVD Player ON 2. Open DVD Tray 3. Press the SET UP button using the remote supplied with the player. 4. Press 9, 8, 7, 0 5. Turn the DVD Player OFF Method 2:

Dantax DVD1000

Dantax DVD450

Dantax DVD920

Dantax DVS2500

Datawrite

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_press numbers press left arrow 6 press left arrow in the setup menu you should now see VERSION go to this and press play now 1 press right > arrow 2 press up/down arrow to change the region code note 0 is region free 3 press play to lock the region Daytek dvd-700 press setup enter 13798888 goto version select code 0 for region free.
Daytek DVD-705M 1) player ON 2) press 9735 now you will get into another menu where you can change the region code Daytek DVD-707 Method 1: 1. Power the player up. 2. Press "Setup". 3. Type "13698888" on the remote. A new menu item, "version", appears. 4. Press "Cursor down" until "version" is highlighted. 5. Press "Play" (remote). 6. Press "Cursor up" or "Cursor down" to set the region code to "1", "2", or "0" (multiregion). 7. Press "Setup". Method 2: 1) player ON 2) press 9735 now you will get into another menu where you can change the region code Daytek DVD-868V10 When the power is on. Open the tray. Enter '9735'. A hidden menu should apare.
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 You can change to all the regions or make it region free. Daytek DVD-868V50 When the power is on. Open the tray. Enter '9735'. A hidden menu should apare. You can change to all the regions or make it region free. Daytek DVR-P30 There is a secret menu hidden when you press setup. Highlight, but do not press the 'exit' button. Then press the keys; and then press enter. You'll have access to a ,MENU which allows your recorder to become region free and macrovision free as well. Make sure there is no disk in the machine. Daytek M700M Method 1: - Switch player on - enter 'setup' (on remote control) - carefully enter the following code on remote control: 13798888 - an additional entry appears: 'version' - select 'version' - select region 0 for code free - done Method 2: 1. Power up the player with no disk in the drive. 2. Press "Setup" on the remote. 3. Type "13698888" on the remove. 4. The item "Version" is added. 5. Select the item version by pressing "Play". The cursor is now placed on the item "Region code". 6. Press "Right arrow" button. The region code now turns purple. 7. Press "Up" or "Down" to select the correct region code. 8. Press "Left arrow". 9. Select "Main menu". 10. Press "Power" on remote. Method 3: For version 3.01 Setup + search the screen where you can select "password"

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 - 5 for Russia, Eastern Europe, India, most of Africa, North Korea, and Mongolia - 6 for China Denver DVD-132 1. Open the tray 2. Punch in the number 3308 followed by the number of the desired region 3. Press Play For all regions you punch 33080, for RCE US DVDs you punch 33081, very useful. Denver DVD-141 1.) Press EJECT 2.) Type on Remote Contol: 330880 (330880 = Reg 0, 330882 = Reg 2) 3.) Close 1.) Press EJECT 2.) Type on Remote Contol: 77390 3.) Close

Denver DVD-142

Denver DVD-152 These dvd players from Denver usually support multi-region by default (even if you have the region number on the back). To confirm it, press "SETUP" then 2188. "VERSION" Message pops up. "VERSION 0" - is multiregion. Turn off your player, then turn on again. Thats it. Denver DVD-172 1. Turn the DVD-player on with the remote control. 2. Open the disc tray using the remote and make sure it is empty. 3. Enter the code 7, 7, 3, 9 on the remote. (The numbers will be indicated by X's on the screen). 4. Wait until the X's have disapeared from the screen. 5. Now enter the region wich the DVD-player should be set to by using the numbers on the remote control. 1 for region 1, 2 for region 2 and so on. 0 equals region free. 6. Turn off the DVD-player and back on (always with the remote) and. it's done! do the following in the "no disc"-menu: *Make sure your DVD-player is on. *open the disc tray using the remote control. *Enter the code 7, 7, 3, 9 on the remote. (The numbers will be indicated by X:s on the screen). *Now wait a second or two until the X:s have dissapeared on the screen. *Now enter which region the DVD-player should be set to by using the numbers on the remote control. (1 for region 1 and 2 for region 2 etc). I recommend you press 0 because 0 equals region

Denver DVD-176

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 free. Now you can put a movie into the tray and play it whichever the region is! Denver DVD-182 1. Press open on the remote control to open the tray. 2. Type in 7739 followed by 0 for region free, 1 for region 1 and so on. 3. Press the PLAY button on the remote, the tray will close and your're all set to go! 1) Open the DVD-door 2) Slowly press 7739 on the remote control (an X will appear on screen for every key pressed) 3) Press 0 (0=multicode(all regions), 1=region 1 , 2 = region 2) 1) Open the DVD-door 2) Slowly press 3308 on the remote control (an X will appear on screen for every key pressed) 3) Press 0 (0=multicode(all regions), 1=region 1 , 2 = region 2 or 3.) These dvd players from Denver usually support multi-region by default (even if you have the region number on the back). To confirm it, press "SETUP" then 2188. "VERSION" Message pops up. "VERSION 0" - is multiregion. Turn off your player, then turn on again. Thats it. Denver DVD-311 1. Power the DVD player up. 2. Open the DVD door by presing the "OPEN" on the front panel. 3. Press the "SETUP" on the remote controel. Then you will se the DVD player menu. 4. Then press 33088 followed by 1 for regionfor region2. 0 for all region 5. In the on screen the DVD player writes R1 for region 1 and so on. 1. Power the DVD player up. 2. Open the DVD door by presing the "OPEN" on the front panel. 3. Press the "SETUP" on the remote controel. Then you will se the DVD player menu. 4. Then press 33088 followed by 1 for regionfor region2. 0 for all region

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 3. Region change menu is on screen Digix Media DV526UP Power up the player and open the tray. With the tray open, press setup button on remote. Then, press 8888 on the remote. After this, press the chapter foward button and you should see a Factory Control Page that allows you to set the region to All. Method 1: Power up the player and open the tray. With the tray open, hit the setup button and then 0000 and then the "Up" button. On the Setup menu, go to Version and hit enter. Go to region code and change the number to 0 for region free and hit setup again to save. Method 2: Power up the player and open the tray. Press the SETUP button. The setup menu appears. Press ZERO on the remote control four times - 0000 Press the CHAPTER FORWARD button - the one on the bottom right of the remote control unit that looks like a double arrow with a bar. A new menu item appears, "Version". There is a REGION option you can select, and this can be set to zero "0" for all regions. Once you see it's set to region 0, press SETUP to exit, close the tray and power off. When you power up again, it's region free. RCE disks work fine in this unit. To recap - open the tray, press setup, press 0-0-0-0, press Chapter Forward, select Version, choose 0 for region free, press setup again. Method 3: 1) Turn on the System 2) Open the tray 3) Press "setup" button 4) Press four time the number "8": 8888 5) Press the "Next Chapter" button (>>|) 6) Appear a menu called "Setup Factory" 7) Select with the cursor movement key "Region All" 8) Press "setup" button to save de changes. Dimarson DM-350 1. Open the player disc tray. 2. Press Setup on the remote control. 3. Go to the submenu Custom Setup, by pressing the right arrow on the remote control 4 times. 4. Using the remote control, key in 3, 3, 3, 3. This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1

Firstline FDVD2000 1.- turn the dvd player on 2.- press eject from the remote control 3.- press Enter 4.- press successively 2, 0, 1, 1, 0
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 5.- DVD will show up a message on the TV screen: SET OK. Firstline FLAV10 Method 1: 1. Open the dvd caddy VIA REMOTE CONTROL. 2. Press in sequence the numbers 8, 4, 2, 1 on the remote (you will see lines appear in the upper left corner of the standby screen on TV, at the fourth digit a new "Region" menu will pop up) 3. Choose the zone "1 to 8 or even ALL" from the menu by press UP or DOWN button on the remote. 4. Confirm your choice with SETUP remote button. The player will keep the chosen Region setting when in standby mode. NOTE: if you turn off the player from the front ON/OFF switch it will reset Region to the original factory setting. Method 2: Press OPEN from the Remote Control. Press INTRO on the remote control. Type 2, 0, 1, 1, 0. The TV screen will show "Set OK" Firstline FLAV20 Method 1: Press OPEN from the Remote Control. Press INTRO on the remote control. Type 2, 0, 1, 1, 0. The TV screen will show "Set OK" Method 2: Press OPEN from the Remote Control. Press INTRO on the remote control. Type 2, 1, 1, 0. The TV screen will show "Set OK" Fisher S1000 1. Program, Right, Right, Enter, Play 2. The player should now be in multiregion mode. 3. You can use Up and Down instead of that second Right keypress to choose other tracks on the DVD. 4. The hack is not permanent and has to be entered every time. Insert a dvd into the player

Fisher S1100

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 1. Press the Program button on your remote control 2. Press the Right Cursor button on your remote control 3. Press the Right Cursor button on your remote control 4. Press the Enter button on your remote control 5. Press the Play button on your remote control Fisher S1500 1. Program, Right, Right, Enter, Play 2. The player should now be in multiregion mode. 3. You can use Up and Down instead of that second Right keypress to choose other tracks on the DVD. 4. The hack is not permanent and has to be entered every time
Force DVD-Master 1. start in DVD mode , no media in slot. 2. press "77" and "OK" on remote. 3. select zone "0" 4. Leave menu. Fujilink TH368 Open press "setup" Press region number (no region=0) press "step" press "prev" press "next" press "setup" Close Method 1: 1. Power on with no disk inside 2. Press right arrow 3. press 8, 0, 0, followed by the region # you want 4. Press Enter You will notice a change in the serial number. If you press any keys and get the "No Disk" message on screen, you need to power off and start again. It took me a couple tries. Method 2: Enter "Setup" menu on the screen. Scroll down and highlight "Exit". While "Exit" is highlighted enter 2,9,6, and 0 and press "Enter". A hidden menu pops up and you can select your region & MacroVision on-off. Gateway Connected + Make sure you have no CD/DVD in the player

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 The numbers should show up, you WILL hear a clicking sound but dont worry, your player is only adjusting to and saving the change JVC XV-S302SL Make sure there is no disc in the player Unplug dvd player Plug system back in while holding the "Open/Close" and the "play" buttons (ON THE PLAYER, NOT the remote) The word "Test" should come up on the player Display Press "9" on the remote until the display on the player says "00A0 0000" Press "Standby/on" (remote or player) Wait 15 seconds Turn player back on YOUR PLAYER IS NOW REGION FREE!!!!! (This Hack also works for the 300 *Black* version) JVC XV-S332SL Have no dvd or cd in the player step 1.unplug the dvd player Plug player back in while holding the Open/Close and play buttons on the player The word TEST and a number should come up on the player Display Step 2.Press 9 on the remote until the display on the player says 00Ait should take 40seconds of pressing 9 to get to 00Aas I think its the last code in the sequence. step3.Press Standby/on on the remote or player Wait 15 seconds Turn player back on. JVC XV-S40BK Make sure there is no disc in the player Unplug dvd player Plug system back in while holding the "Open/Close" and the "play" buttons (ON THE PLAYER, NOT the remote)
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 The word "Test" should come up on the player Display Press "9" on the remote until the display on the player says "00A0 0000" Press "Standby/on" (remote or player) Wait 15 seconds Turn player back on YOUR PLAYER IS NOW REGION FREE!!!!! JVC XV-S60BK Unplug the unit from the wall and leave it for a minute. Plug it back in and push the power button. Take the remote control in one hand and put a cd or dvd case on top of the buttons. Make sure you cover all the buttons except for the power and the open/close button. Press down and hold the case against all the buttons at the same time for a few minutes. I repeated the steps 4 times, however it may not have been necessary and now it works. JVC XV-S60 is region free. With the machine on and no disk loaded, press Setup on the remote. When the Setup menu appears, press Skip -, Skip +, Skip -, Skip +, Skip -. It will then indicate the version (region) setting in the upper right-hand corner. Use the left and right arrow buttons on the remote to select the region you want. selecting VER 255 will set the player to be code free. Press Return on the remote once you have made the selection. No need to turn the machine off and on again. jWIN JD-VD120 1- Press Setup Button 2- Press 1,3,6,9 3- Region Code display should appear (For Example: Region Code 1) 4- Use Up & Down key from remote control to change the Region (If the Region Code is 1, then press Down Key you will see Region Code 0) 5. Press Enter from remote control to accept the change 1) Open tray 2) Press the "PROG" button 3) Press the "ENTER" button 3 times 4) An indicator of the zone will be whown 5) With the UP/DOWN arrow keys set the region to 0 (for multiregion)

KiSS DP-330

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 update drev go to hidden menu press on remote: eject + back + 276 it can be a little tricky to get in sercet menu, just keep trying. KLH DVD-33 1. Make sure it is in dvd mode. 2. Open the disc tray and wait for it to say "OPEN" 3. On the remote, press 9817. 4. A secret menu will appear that will allow you to change the region (1,2,3,4,5,6, or 9) and turn macrovison on or off. 5. Use the arrow buttons to select which option you want to change. 6. Use the enter button to set the desired setting. 7. Press the return button to leave the menu. 8. Play dvd as usual 1) Press PAUSE button 2) Press numbers 3826210937 3) Wait 5 sec 4) Press 5 5) Press Pause 6) Press Enter 7) Power off and wait 1 min.

KLH KD-1220

Konka KD-1800U Turn on player and open tray On the Remote key in 6, 6, 6, 6, Select A hidden menu will appear on your TV screen 'D-1800 System Setup' Use the directional buttons to scroll down to 'Country Code' Press Select on the Remote and change the setting to the Region Code you need, 1 thru 6. Changing it to 13 to make it code free After entering the desired number press Select From this menu you can change other settings, but to exit the menu just press Return Koss C220 With tray open press "menu" on the remote, and after
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 the main setup menu appears press 1-6-7 on the remote. You will be able to choose between regions 1-6. press "mute" button for all regions region-free. i tried on my koss-C220 it worked. but i did not checked with different region DVD's Koss C928 1. Ensure there is no disc in the player's tray. 2. Using the remote control, key in the following: Menu, 1, 6, 7, followed by the region number required, or use Mute for region free. http://groups.yahoo.com/group/koss216/files/ I just want to share my experience. I tested it on 2 players. Works great. I was able to play region 1,2 and All after hack. I just wanted to let everyone know that the above hacks work. You can go to the yahoo groups, download the program, and do your upgrading with no problems. Trust me, I am a total newbie, and only recently found out that DVDs are hackable. It is very easy. Also, since most people have EZ CD Creator, which comes with their new computers, this website really helped me out: http://www.area450.com/firmware/burnfirmware2.htm#Easy%20CD%20Creator Even though when you download the file from the yahoo group, the readme file specifically says " DO NOT use UDF packet writing type software such as direct cd to author the Disk." I didn't follow their advice (since I didn't really know any better, and followed the instructions on the area450 website (link above), and came out with fantastic results. ***Also, although there may be some confusion, I know I was a bit worried about the idea that the Koss player I had was not specifically the one listed in this forum, I found out by reading the yahoo group that this hack works on the DVP-2161, DVP-2162, DVP-2163, and DVP-2164. The only differences between the numbers are the colors offered and the inclusion or lack thereof of those flower decoration. I just wanted to let everyone know not to be afraid, and it does work. And even if you are still afraid, the yahoo group above gives you the download of the original software that came with your Koss player - so even if you screw up, you can always put it back to the original settings. Koss KD210 With tray open press "menu" on the remote, and after the main setup menu appears press 1-6-7 on the remote. You will be able to choose between regions 1-6. "0" is said to leave the machine

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Player will now play selected region 1-9 (or all regions (0) Medion MD 4310 Method 1: 1. Press the Open/Close button on your remote control 2. Press the Setup button on your remote control 3. On your remote control, press the 1 button for region 1, 2 for region 2, and so on, or 0 for multi-region playback 4. Press the Pause button on your remote control 5. Press the Step Back button on your remote control 6. Press the Step Forward button on your remote control 7. Press the Setup button on your remote control Method 2: To change the region 1. Press the Open button on your player to open the drive tray 2. Press the Clear button on your remote control 3. Press the 1 button on your remote control 4. Press the 3 button on your remote control 5. Press the 6 button on your remote control 6. Press the 9 button on your remote control 7. Using your remote control, enter 1 for region 1, 2 for region 2, and so on, or 0 for multi-region playback Medion MD 4358 1. Turn On the DVD 2. push open/close (let the tray be open) 3. Push Setup Button 4. Push the 7 Button 5. Push Pause/Step 6. Push Reverse/Skip 7. Push Forward/Skip 8. Push Setup - open tray - press clear - press 1 - 3 - 6 - 9 - press 0 for multi-region (or 1 for region 1, 2 for region 2, etc.) * Remove any DVD or CD in the player * Press MENU * Press 1 * Press 6

Medion MD 4359

Medion MD 4364
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 * Press 7 Region will be asked. * Press MUTE for region 0 / free Medion MD 4560 Method 1: 1. Open Tray 2. Press "Clear" Button 3. Press 1,3,6,9 4. Select Region code by pressing: 1 = Region = Region = Region = Region = Region = Region = CODEFREE 5. Close Tray 6. Switch ON/OFF Method 2: Eject (tray must be open) Setup 0 (for region-free) pause step-back step-forward setup Medion MD 4847 Method 1: Eject (tray must be open) Setup 0 (for region-free) pause step-back step-forward setup Method 2:
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Eject-open (tray must be open) Setup 0 (for region-free)(or any other numbers, 1 for r1 (region1), and 2 for r2 etc.) pause skip - << (skip-back) skip - >> (skip-forward) setup Medion MD Open tray 2 Press clear button 3 Press press 0 for code free 5 Close tray 6 Turn off 7 Play any dvd this works 1.) Schublade ffnen 2.) Taste CLEAR drcken 3.) Danach den Code "1369" eingeben 4.) Jetzt entweder "0" whlen oder 1 oder 2 oder. fr die verschiedenen Regionen. Power on Eject Loader Press: SETUP Press: Press: Left 3 times Press: Right 1 time Now a new line (Version) appears. Select this and choose region (0 = region free) Open Tray Press Clear 1,6,for all regions Open DVD-drawer. Press "Setup" Number key "1-3-6-9" Arrow key left "3 time" Arrow key right "1 time" "Menu coming up" Choose Number key for country code.

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 2. Turn on the DVD player. 3. Using the remote control, press the "setup" button and use the right arrow key to advance to the far right-hand tab entitled "Preferences" Note: If there is a disc in the player, you will not see the "Preferences" tab!!!! 4. Enter code number 1379 and then use the up and down arrows to change the arrow code to mtch the DVD you want to play. Note: I set my to "0" and it now plays both region 1 and region 2 discs without having to reset the region each time you want to watch different-region discs. 5. Once the applicable code is shosen, press the "enter" button to save and the "setup" button to exit. Polaroid PDV-0801A 1. Remove the DVD from the player. 2. Using the remote control, press the "Set-Up" button and advance to the far right-hand tab "Preferences". 3. Enter Code # 1379 then use the "up & down arrows" to change the Region Code. Region "0" means all regions. 4. Once code is chosen, press enter Polaroid PDV-0813A 1. Remove DVD disc from unit. 2. Turn on the DVD player. 3. Using the remote control, press the "setup" button and use the right arrow key to advance to the far right-hand tab entitled "Preferences" Note: If there is a disc in the player, you will NOT see the "Preferences" tab!!!! 4. Enter code number 1379 and then use the up and down arrows to change the arrow code to match the DVD you want to play. Note: I set my to "0" and it now plays both region 1 and region 2 discs without having to reset the region each time you want to watch different-region discs. I assume it will now also play regions 3-4-5-6 but I don't have any such discs to try it out. 5. Once the applicable code is chosen, press the "enter" button to save and the "setup" button to exit. Polaroid PDV-0820 1. Remove DVD disc from unit. This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 2. Turn on the DVD player. 3. Using the remote control, press the "setup" button and use the right arrow key to advance to the far right-hand tab entitled "Preferences" Note: If there is a disc in the player, you will NOT see the "Preferences" tab!!!! 4. Enter code number 1379 and then use the up and down arrows to change the arrow code to match the DVD you want to play. Note: I set my to "0" and it now plays both region 1 and region 2 discs without having to reset the region each time you want to watch different-region discs. I assume it will now also play regions 3-4-5-6 but I don't have any such discs to try it out. 5. Once the applicable code is chosen, press the "enter" button to save and the "setup" button to exit. Polaroid PDV-0821T 1. Remove DVD disc from unit. 2. Turn on the DVD player. 3. Using the remote control, press the "setup" button and use the right arrow key to advance to the far right-hand tab entitled "Preferences" Note: If there is a disc in the player, you will NOT see the "Preferences" tab!!!! 4. Enter code number 1379 and then use the up and down arrows to change the arrow code to match the DVD you want to play. Note: Setting the region code to 0 will make it region free. 5. Once the applicable code is chosen, press the "enter" button to save and the "setup" button to exit. Polaroid PDV-1002A 1. Remove DVD disc from unit. 2. Turn on the DVD player. 3. Using the remote control, press the "setup" button and use the right arrow key to advance to the far right-hand tab entitled "Preferences" Note: If there is a disc in the player, you will NOT see the "Preferences" tab!!!! 4. Enter code number 1379 and then use the up and down arrows to change the arrow code to match the DVD you want to play. Note: I set my to "0" and it now plays both region 1 and region 2 discs without having to reset the region each time you want to watch different-region discs. I assume it will now also play regions

Proline DVD1000

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Open the disc tray Place a region 2 disc in the tray, but don't close it Press the buttons Return and then Play on your remote control in order, one at a time Proline DVD1040 Method 1: When the disc is loading, press the number 1 several times. This will ensure that you can watch other regions, however you won't be able to use your remote. To get rid of the wrong region sign at the top of the screen, press the P/N button and this will be replaced by a more eye catching stop sign When the disc is loading, press the number 2 several times. This will ensure that you can watch other regions, however you won't be able to use your remote. To get rid of the wrong region sign at the top of the screen, press the P/N button and this will be replaced by a more eye catching stop sign Method 2: 01. If you have a disc in the tray, take it out first and THEN turn the power off on the unit; 02. Turn the power on with the remote control; 03. Open the tray with the remote control and leave open for the duration of this procedure; 04. Push the SETUP button on your remote control; 05. Arrow down on the remote control to the "Exit Setup" option - BUT DON'T CHOOSE IT!; 06. Now press, 1, 3, 6, 9 on your remote control (TIP - Get pretty close to the unit as the open tray may block the infra-red); 07. Using your remote control, press once; 08. A new option appears on the Set Up Menu called "Version", choose it and press the ENTER/> button; 09. Exit all the menus until you arrive back at the blue screen with the DVD logo on; 10. Now press the P/N button on your remote control. The word "MULTI" will appear at the top of your screen. 11. Close the tray by pressing the button on the unit. Proline DVD1050 01. If you have a disc in the tray, take it out first and THEN turn the power off on the unit; 02. Turn the power on with the remote control; 03. Open the tray with the remote control and leave open for the duration of this procedure; 04. Push the SETUP button on your remote control; 05. Arrow down on the remote control to the "Exit Setup" option - BUT DON'T CHOOSE IT!; 06. Now press, 1, 3, 6, 9 on your remote control (TIP - Get pretty close to the unit as the open tray may block the infra-red); 07. Using your remote control, press once;

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 7. Press OPEN on the Player to open the disc tray. 8. Press STANDBY (POWER) on the remote control to close the tray. Next time the player is turned on it will set to the region specified.
Method 2: 1. Cold start the player, by holding down the PLAY and STOP buttons on the player. 2. You should see a set of language options. Release the PLAY and STOP buttons. 3. Select your language. 4. Press REPEAT (not the repeat A-B button). 5. Press 3 - 5, 6, 7, 3, 2 6. Press 9 for region-free. 7. Press OPEN on the Player to open the disc tray. 8. Press STANDBY (POWER) on the remote control to close the tray. Next time the player is turned on it will set to the region specified. Samsung DVDP248K 1. Switch off you player at the main then, then switch in whilst you hold down the PLAY and STOP buttons on the player. 2. You should see a set of language options. Release the PLAY and STOP buttons. 3. Select your language. 4. Press REPEAT (not the repeat A-B button). 5. Press 5-6-7-3-2 6. Press 9 for region-free. 7. Press OPEN on the Player to open the disc tray. 8. Press STANDBY (POWER) on the remote control to close the tray. Next time the player is turned on it will set to the region specified.
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Samsung DVDP249M 1. Make sure that there is no disc in the player 2. Turn the player ON 3. Press Repeat key 4. Press 53814 After this code you should see digit "2"(this digit is region code maybe also 4,5 etc.) displayed in the left upper corner of the screen. 5. Press 9, and then press OPEN/CLOSE two times on your remote control (!) to open and close the CD tray. 6. Shut the player off. Method 1: 1. Make sure that there is no disc in the player 2. Turn the player ON 3. Press Repeat key 4. Press 53814 After this code you should see digit "2"(this digit is region code maybe also 4,5 etc.) displayed in the left upper corner of the screen. 5. Press 9, and then press OPEN/CLOSE two times on your remote control (!) to open and close the CD tray. 6. Shut the player off. If the above doesnt work, try 5-6-7-3-2 for step 4 Method 2: 1: Turn DVD player on, with NO DVD in the tray. 2: Press Repeat on remote control (Bottom right key) 3: Enter 76884 (Should see a Yellow 4 or any other number displayed) 4: Press 9 (Previous number change to a yellow 9) 5: Open tray, close tray 6: Turn off DVD player, turn it back on. Samsung DVDP255K 1: Turn DVD player on, with NO DVD in the tray. 2: Press Repeat on remote control (bottom right key) 3: Enter 76884

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 player back on. Samsung DVD-S228 *USE YOUR REMOTE FOR THIS PROCESS. 1. Turn DVD player on with no disc inserted. 2. Press "REPEAT" once on your remote control. 3. If your DVD player is: Region 1 coded type: 4 or, Region 2 coded type: 7 or, Region 3 coded type: 2 or, Region 4 coded type: 4 or, Region 5 coded type: 4 or, Region 6 coded type: 2 *So if your dvd player only plays dvd's that are region 1 coded you would type 4 4. Then press 9 on your remote control. 5. Press Open button on the remote control. 6. Wait 10 seconds. 7. Turn power off. *YOUR "SAMSUNG DVD-S228" IS NOW REGION CODE FREE AND CAN PLAY ANY DVD FROM ANY COUNTRY. Samsung DVD-S323 Method 1: press repeat, then times open/close and power off Method 2: 1.- Power on DVD 2.- wait message "No Disc" 3.- press "repeat" 4.- press =>7=>6=>8=>8=>4 5.- wait that clear number on screen 6.- press quickly 9
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 7.- open with remote control 8.- insert disk zone 1 9.- press "stand by/on" 10.- power on DVD 11.- ready Method 3: First, unplug and plug again the player, then press play button on the player and hold it, press the stop button (on the player too) and hold it, the player will power on automatically. You will now need to select a language option in the menu that appears. Now, press the repeat button on the remote control (if are two buttons, use the button that haven't the "a-b" mark), after this, press the secuence number according to the region code that have your player currently: Region 1 use 2, 9, 3, 3, 4 Region 2 use 3, 8, 7, 6, 7 Region 3 use 5, 6, 7, 3, 2 Region 4 use 7, 6, 8, 8, 4 Region 5 use 5, 3, 8, 1, 4 Region 6 use 2, 4, 4, 6, 2 After this press 9 press "open/close" button on your player press "power" button in your remote control Ready. Samsung DVD-S324 1)leave disc tray empty 2)press repeat 3) press 57538 4) a "2" will appear on the top left hand corner of the screen 5)press number 9 (this is for multiregion, apparently if you press 1 ,you get region1 ,press 2 you get region 2 etc) 6)press open button 7) power off after 15 seconds 8) power on and youre in da zone :-D Samsung DVD-S325 Power on your player whilst pressing hold both the FF and Pause buttons on the front player After a short while you should be presented with a set of language options. Release the Play and Stop buttons on the player You will now need to select a language option between 1 and 6 To convert this player to Multi-Region playback:

This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 Method 2: 1. Turn the power of your player on (without disc) 2. Wait for menu 3. Using your remote control enter the code 1,6,7,1,9 4. choose region with up/down arrow 5. Turn the player off.and then you can play! Thomson DTH-222 1, 6, 7, 1, 9 A text shows up with the current region Press 0 for All regions Thomson DTH-223E -unplug the player for 20 sec -turn on the player without any disk inside -enter the code 456 -a menu appears, select 'all' in the list for all regions -turn the player off Thomson DTH-231 1. Turn on the player without a disc inside 2. Wait for the menu 3. Using the remote enter the following code: 1, 6, 7, 1, 9. 4. Chose region (0 for all regions). 5. Turn the player off! Thomson DTH-233E In STOP mode without Disc on the tray Enter 3, 2, 1, 7, 8, 9, 4, 5, 6 Select with up / down on the OSD screen the required code & confirm with OK Thomson DTH-311E Method 1: - turn the player on without any disc inside - enter the code 456 before the player menu appears - select 'all' in the appearing list for regionfree - turn the player off Method 2: - turn the player on without any disc inside - enter the code 16719 when the menu appears
This NON RESELLABLE document has been brought to you by: Best.Seller_1 @ eBay To find more items sold by me, go to: http://cgi6.ebay.com/ws/eBayISAPI.dll?ViewSellersOtherItems&userid=best.seller_1 - select 0 far all, 1 for zone 1. in the appearing list Thomson DTH-3300 Press the Repeat button on your remote control Using your remote control enter the code below, note that you must know what Region your player is currently set to in order to know which code is appropriate for Region 1 use 2, 9, 3, 3 and 4 for Region 2 use 3, 8, 7, 6 and 7 for Region 3 use 5, 6, 7, 3 and 2 for Region 4 use 7, 6, 8, 8 and 4 for Region 5 use 5, 3, 8, 1 and 4 for Region 6 use 2, 4, 4, 6 and 2 A code should be displayed on the screen indicating the current Region setting of your unit. Press the 9 button on your remote control for Region free, or 1 for Region 1, 2 for Region 2 and so o Thomson DTH-3600 1. Power on your player 2. Press and hold both the Play and Stop buttons on the player 3. After a short while you should be presented with a set of language options. Release the Play and Stop buttons on the player 4. You will now need to select a language option between 1 and 6 To convert this player to Multi-Region playback 1. Press the Repeat button on your remote control 2. Using your remote control enter the code below, note that you must know what Region your player is currently set to in order to know which code is appropriate for Region 1 use 2, 9, 3, 3 and 4 for Region 2 use 3, 8, 7, 6 and 7 for Region 3 use 5, 6, 7, 3 and 2 for Region 4 use 7, 6, 8, 8 and 4 for Region 5 use 5, 3, 8, 1 and 4 for Region 6 use 2, 4, 4, 6 and 2 3. A code should be displayed on the screen indicating the current Region setting of your unit. 4. Press the 9 button on your remote control for Region free, or 1 for Region 1, 2 for Region 2 and so on. 5. Press the Open button on your player 6. Press the Standby button on your remote control If the player sticks on FBI Warning screens

DVD-215

SUPER SLIM PROGRESSIVE SCAN DVD PLAYER
Progressive Scan DVD Player Super Slim Design Plays DVD/MP3/CD/CD-R/CD-RW/Kodak Picture CD Compatible with PAL/NTSC Multiple Subtitles/Viewing Angle Convenient On Screen Display Zoom Operation Parental Lock Control Full Function Remote Control 110-220 Automatic Power Adjustable Input FCC Approved & UL Listed FDA Approved Specifications: Audio Dolby Digital Coaxial Digital Out Optical Digital Out Analog Audio Output Video Component Video Out (Progressive Scan) RCA Video Out S-Video Out Carton - Inner: 1 Master: 1 UPC: 99215 9

MIRROR FRONT

www.cobyusa.com and www.ecoby.com
2004 COBY ELECTRONICS CORPORATION Features and specifications are subject to change without prior notification Printed in USA